- Dynamic Device Personalization (DDP)
- Queue region configuration
- Virtual Function Port Representors
+- Malicious Device Drive event catch and notify
+- Generic flow API
Prerequisites
-------------
- Upgrade the NVM/FW version following the `Intel® Ethernet NVM Update Tool Quick Usage Guide for Linux
<https://www-ssl.intel.com/content/www/us/en/embedded/products/networking/nvm-update-tool-quick-linux-usage-guide.html>`_ and `Intel® Ethernet NVM Update Tool: Quick Usage Guide for EFI <https://www.intel.com/content/www/us/en/embedded/products/networking/nvm-update-tool-quick-efi-usage-guide.html>`_ if needed.
+- For information about supported media, please refer to this document: `Intel® Ethernet Controller X710/XXV710/XL710 Feature Support Matrix
+ <http://www.intel.com/content/dam/www/public/us/en/documents/release-notes/xl710-ethernet-controller-feature-matrix.pdf>`_.
+
+ .. Note::
+
+ * Some adapters based on the Intel(R) Ethernet Controller 700 Series only
+ support Intel Ethernet Optics modules. On these adapters, other modules are not
+ supported and will not function.
+
+ * For connections based on Intel(R) Ethernet Controller 700 Series,
+ support is dependent on your system board. Please see your vendor for details.
+
+ * In all cases Intel recommends using Intel Ethernet Optics; other modules
+ may function but are not validated by Intel. Contact Intel for supported media types.
+
Recommended Matching List
-------------------------
list which has been tested and verified. The detailed information can refer
to chapter Tested Platforms/Tested NICs in release notes.
+For X710/XL710/XXV710,
+
+--------------+-----------------------+------------------+
| DPDK version | Kernel driver version | Firmware version |
+==============+=======================+==================+
+ | 20.05 | 2.11.27 | 7.30 |
+ +--------------+-----------------------+------------------+
+ | 20.02 | 2.10.19 | 7.20 |
+ +--------------+-----------------------+------------------+
| 19.11 | 2.9.21 | 7.00 |
+--------------+-----------------------+------------------+
| 19.08 | 2.8.43 | 7.00 |
| 16.04 | 1.4.25 | 5.02 |
+--------------+-----------------------+------------------+
+
+For X722,
+
+ +--------------+-----------------------+------------------+
+ | DPDK version | Kernel driver version | Firmware version |
+ +==============+=======================+==================+
+ | 20.05 | 2.11.27 | 4.11 |
+ +--------------+-----------------------+------------------+
+ | 20.02 | 2.10.19 | 4.11 |
+ +--------------+-----------------------+------------------+
+ | 19.11 | 2.9.21 | 4.10 |
+ +--------------+-----------------------+------------------+
+ | 19.08 | 2.9.21 | 4.10 |
+ +--------------+-----------------------+------------------+
+ | 19.05 | 2.7.29 | 3.33 |
+ +--------------+-----------------------+------------------+
+ | 19.02 | 2.7.26 | 3.33 |
+ +--------------+-----------------------+------------------+
+ | 18.11 | 2.4.6 | 3.33 |
+ +--------------+-----------------------+------------------+
+
+
Pre-Installation Configuration
------------------------------
protocols/filters which are not supported by default. The DDP
functionality requires a NIC firmware version of 6.0 or greater.
-Current implementation supports GTP-C/GTP-U/PPPoE/PPPoL2TP,
+Current implementation supports GTP-C/GTP-U/PPPoE/PPPoL2TP/ESP,
steering can be used with rte_flow API.
GTPv1 package is released, and it can be downloaded from
PPPoE package is released, and it can be downloaded from
https://downloadcenter.intel.com/download/28040.
+ESP-AH package is released, and it can be downloaded from
+https://downloadcenter.intel.com/download/29446.
+
Load a profile which supports GTP and store backup profile:
.. code-block:: console
testpmd> set port (port_id) queue-region flush (on|off)
testpmd> show port (port_id) queue-region
+Generic flow API
+~~~~~~~~~~~~~~~~~~~
+
+- ``RSS Flow``
+
+ RSS Flow supports to set hash input set, hash function, enable hash
+ and configure queue region.
+ For example:
+ Configure queue region as queue 0, 1, 2, 3.
+
+ .. code-block:: console
+
+ testpmd> flow create 0 ingress pattern end actions rss types end \
+ queues 0 1 2 3 end / end
+
+ Enable hash and set input set for ipv4-tcp.
+
+ .. code-block:: console
+
+ testpmd> flow create 0 ingress pattern eth / ipv4 / tcp / end \
+ actions rss types ipv4-tcp l3-src-only end queues end / end
+
+ Set symmetric hash enable for flow type ipv4-tcp.
+
+ .. code-block:: console
+
+ testpmd> flow create 0 ingress pattern eth / ipv4 / tcp / end \
+ actions rss types ipv4-tcp end queues end func symmetric_toeplitz / end
+
+ Set hash function as simple xor.
+
+ .. code-block:: console
+
+ testpmd> flow create 0 ingress pattern end actions rss types end \
+ queues end func simple_xor / end
+
Limitations or Known issues
---------------------------
As i40e PMD supports both 16 and 32 bytes RX descriptor sizes, and 16 bytes size can provide helps to high performance of small packets.
Configuration of ``CONFIG_RTE_LIBRTE_I40E_16BYTE_RX_DESC`` in config files can be changed to use 16 bytes size RX descriptors.
+Input set requirement of each pctype for FDIR
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+Each PCTYPE can only have one specific FDIR input set at one time.
+For example, if creating 2 rte_flow rules with different input set for one PCTYPE,
+it will fail and return the info "Conflict with the first rule's input set",
+which means the current rule's input set conflicts with the first rule's.
+Remove the first rule if want to change the input set of the PCTYPE.
+
Example of getting best performance with l3fwd example
------------------------------------------------------