-.. BSD LICENSE
- Copyright(c) 2010-2016 Intel Corporation. All rights reserved.
- All rights reserved.
-
- Redistribution and use in source and binary forms, with or without
- modification, are permitted provided that the following conditions
- are met:
-
- * Redistributions of source code must retain the above copyright
- notice, this list of conditions and the following disclaimer.
- * Redistributions in binary form must reproduce the above copyright
- notice, this list of conditions and the following disclaimer in
- the documentation and/or other materials provided with the
- distribution.
- * Neither the name of Intel Corporation nor the names of its
- contributors may be used to endorse or promote products derived
- from this software without specific prior written permission.
-
- THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
- "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
- LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
- A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
- OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
- SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
- LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
- DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
- THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
- (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
- OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+.. SPDX-License-Identifier: BSD-3-Clause
+ Copyright(c) 2010-2016 Intel Corporation.
IXGBE Driver
============
* HW extend dual VLAN
-* Enabled by RX_OLFLAGS (RTE_IXGBE_RX_OLFLAGS_ENABLE=y)
-
-
To guarantee the constraint, configuration flags in dev_conf.rxmode will be checked:
* hw_vlan_strip
Sample Application Notes
------------------------
-testpmd
-~~~~~~~
-
-By default, using CONFIG_RTE_IXGBE_RX_OLFLAGS_ENABLE=y:
-
-.. code-block:: console
-
- ./x86_64-native-linuxapp-gcc/app/testpmd -c 300 -n 4 -- -i --burst=32 --rxfreet=32 --mbcache=250 --txpt=32 --rxht=8 --rxwt=0 --txfreet=32 --txrst=32 --txqflags=0xf01
-
-When CONFIG_RTE_IXGBE_RX_OLFLAGS_ENABLE=n, better performance can be achieved:
-
-.. code-block:: console
-
- ./x86_64-native-linuxapp-gcc/app/testpmd -c 300 -n 4 -- -i --burst=32 --rxfreet=32 --mbcache=250 --txpt=32 --rxht=8 --rxwt=0 --txfreet=32 --txrst=32 --txqflags=0xf01 --disable-hw-vlan
-
l3fwd
~~~~~
the advanced context descriptor should be set and set it. And DPDK has to ask
the info about the header length from the upper layer, because parsing the
packet itself is not acceptable. So, it's too expensive to support MDD.
-When using kernel PF + DPDK VF on x550, please make sure using the kernel
-driver that disables MDD or can disable MDD. (Some kernel driver can use
-this CLI 'insmod ixgbe.ko MDD=0,0' to disable MDD. Some kernel driver disables
-it by default.)
+When using kernel PF + DPDK VF on x550, please make sure to use a kernel
+PF driver that disables MDD or can disable MDD.
+
+Some kernel drivers already disable MDD by default while some kernels can use
+the command ``insmod ixgbe.ko MDD=0,0`` to disable MDD. Each "0" in the
+command refers to a port. For example, if there are 6 ixgbe ports, the command
+should be changed to ``insmod ixgbe.ko MDD=0,0,0,0,0,0``.
Statistics
In order to ensure valid results, it is recommended to poll every 4 minutes.
+MTU setting
+~~~~~~~~~~~
+
+Although the user can set the MTU separately on PF and VF ports, the ixgbe NIC
+only supports one global MTU per physical port.
+So when the user sets different MTUs on PF and VF ports in one physical port,
+the real MTU for all these PF and VF ports is the largest value set.
+This behavior is based on the kernel driver behavior.
+
+VF MAC address setting
+~~~~~~~~~~~~~~~~~~~~~~
+
+On ixgbe, the concept of "pool" can be used for different things depending on
+the mode. In VMDq mode, "pool" means a VMDq pool. In IOV mode, "pool" means a
+VF.
+
+There is no RTE API to add a VF's MAC address from the PF. On ixgbe, the
+``rte_eth_dev_mac_addr_add()`` function can be used to add a VF's MAC address,
+as a workaround.
+
+
+Inline crypto processing support
+--------------------------------
+
+Inline IPsec processing is supported for ``RTE_SECURITY_ACTION_TYPE_INLINE_CRYPTO``
+mode for ESP packets only:
+
+- ESP authentication only: AES-128-GMAC (128-bit key)
+- ESP encryption and authentication: AES-128-GCM (128-bit key)
+
+IPsec Security Gateway Sample Application supports inline IPsec processing for
+ixgbe PMD.
+
+For more details see the IPsec Security Gateway Sample Application and Security
+library documentation.
+
Supported Chipsets and NICs
---------------------------
git.droids-corp.org / dpdk.git / blobdiff