-.. BSD LICENSE
+.. SPDX-License-Identifier: BSD-3-Clause
Copyright 2012 6WIND S.A.
- Copyright 2015 Mellanox
-
- Redistribution and use in source and binary forms, with or without
- modification, are permitted provided that the following conditions
- are met:
-
- * Redistributions of source code must retain the above copyright
- notice, this list of conditions and the following disclaimer.
- * Redistributions in binary form must reproduce the above copyright
- notice, this list of conditions and the following disclaimer in
- the documentation and/or other materials provided with the
- distribution.
- * Neither the name of 6WIND S.A. nor the names of its
- contributors may be used to endorse or promote products derived
- from this software without specific prior written permission.
-
- THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
- "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
- LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
- A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
- OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
- SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
- LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
- DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
- THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
- (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
- OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ Copyright 2015 Mellanox Technologies, Ltd
MLX4 poll mode driver library
=============================
-The MLX4 poll mode driver library (**librte_pmd_mlx4**) implements support
+The MLX4 poll mode driver library (**librte_net_mlx4**) implements support
for **Mellanox ConnectX-3** and **Mellanox ConnectX-3 Pro** 10/40 Gbps adapters
as well as their virtual functions (VF) in SR-IOV context.
There is also a `section dedicated to this poll mode driver
<http://www.mellanox.com/page/products_dyn?product_family=209&mtag=pmd_for_dpdk>`_.
-.. note::
-
- Due to external dependencies, this driver is disabled by default. It must
- be enabled manually by setting ``CONFIG_RTE_LIBRTE_MLX4_PMD=y`` and
- recompiling DPDK.
Implementation details
----------------------
Most Mellanox ConnectX-3 devices provide two ports but expose a single PCI
-bus address, thus unlike most drivers, librte_pmd_mlx4 registers itself as a
+bus address, thus unlike most drivers, librte_net_mlx4 registers itself as a
PCI driver that allocates one Ethernet device per detected port.
-For this reason, one cannot white/blacklist a single port without also
-white/blacklisting the others on the same device.
+For this reason, one cannot block (or allow) a single port without also
+blocking (or allowing) the others on the same device.
Besides its dependency on libibverbs (that implies libmlx4 and associated
-kernel support), librte_pmd_mlx4 relies heavily on system calls for control
+kernel support), librte_net_mlx4 relies heavily on system calls for control
operations such as querying/updating the MTU and flow control parameters.
For security reasons and robustness, this driver only deals with virtual
which remain functional, although they stop receiving unicast packets as
long as they share the same MAC address.
-Compiling librte_pmd_mlx4 causes DPDK to be linked against libibverbs.
+The :ref:`flow_isolated_mode` is supported.
-Features
---------
-
-- Multi arch support: x86_64 and POWER8.
-- Link state information is provided.
-- Scattered packets are supported for TX and RX.
-- Inner L3/L4 (IP, TCP and UDP) TX/RX checksum offloading and validation.
-- Outer L3 (IP) TX/RX checksum offloading and validation for VXLAN frames.
-- RX interrupts.
+Compiling librte_net_mlx4 causes DPDK to be linked against libibverbs.
Configuration
-------------
Compilation options
~~~~~~~~~~~~~~~~~~~
-These options can be modified in the ``.config`` file.
-
-- ``CONFIG_RTE_LIBRTE_MLX4_PMD`` (default **n**)
-
- Toggle compilation of librte_pmd_mlx4 itself.
-
-- ``CONFIG_RTE_LIBRTE_MLX4_DEBUG`` (default **n**)
-
- Toggle debugging code and stricter compilation flags. Enabling this option
- adds additional run-time checks and debugging messages at the cost of
- lower performance.
-
-- ``CONFIG_RTE_LIBRTE_MLX4_DEBUG_BROKEN_VERBS`` (default **n**)
+The ibverbs libraries can be linked with this PMD in a number of ways,
+configured by the ``ibverbs_link`` build option:
- Mellanox OFED versions earlier than 4.2 may return false errors from
- Verbs object destruction APIs after the device is plugged out.
- Enabling this option replaces assertion checks that cause the program
- to abort with harmless debugging messages as a workaround.
- Relevant only when CONFIG_RTE_LIBRTE_MLX4_DEBUG is enabled.
+- ``shared`` (default): the PMD depends on some .so files.
-- ``CONFIG_RTE_LIBRTE_MLX4_MAX_INLINE`` (default **0**)
+- ``dlopen``: Split the dependencies glue in a separate library
+ loaded when needed by dlopen.
+ It make dependencies on libibverbs and libmlx4 optional,
+ and has no performance impact.
- Amount of data to be inlined during TX operations. Improves latency but
- lowers throughput.
+- ``static``: Embed static flavor of the dependencies libibverbs and libmlx4
+ in the PMD shared library or the executable static binary.
-- ``CONFIG_RTE_LIBRTE_MLX4_TX_MP_CACHE`` (default **8**)
-
- Maximum number of cached memory pools (MPs) per TX queue. Each MP from
- which buffers are to be transmitted must be associated to memory regions
- (MRs). This is a slow operation that must be cached.
-
- This value is always 1 for RX queues since they use a single MP.
Environment variables
~~~~~~~~~~~~~~~~~~~~~
-- ``MLX4_INLINE_RECV_SIZE``
+- ``MLX4_GLUE_PATH``
+
+ A list of directories in which to search for the rdma-core "glue" plug-in,
+ separated by colons or semi-colons.
- A nonzero value enables inline receive for packets up to that size. May
- significantly improve performance in some cases but lower it in
- others. Requires careful testing.
Run-time configuration
~~~~~~~~~~~~~~~~~~~~~~
-- librte_pmd_mlx4 brings kernel network interfaces up during initialization
+- librte_net_mlx4 brings kernel network interfaces up during initialization
because it is affected by their state. Forcing them down prevents packets
reception.
times for additional ports. All ports are probed by default if left
unspecified.
+- ``mr_ext_memseg_en`` parameter [int]
+
+ A nonzero value enables extending memseg when registering DMA memory. If
+ enabled, the number of entries in MR (Memory Region) lookup table on datapath
+ is minimized and it benefits performance. On the other hand, it worsens memory
+ utilization because registered memory is pinned by kernel driver. Even if a
+ page in the extended chunk is freed, that doesn't become reusable until the
+ entire memory is freed.
+
+ Enabled by default.
+
Kernel module parameters
~~~~~~~~~~~~~~~~~~~~~~~~
The **mlx4_core** kernel module has several parameters that affect the
-behavior and/or the performance of librte_pmd_mlx4. Some of them are described
+behavior and/or the performance of librte_net_mlx4. Some of them are described
below.
- **num_vfs** (integer or triplet, optionally prefixed by device address
following limitation: VLAN filtering is not supported with this mode.
This is the recommended mode in case VLAN filter is not needed.
+Limitations
+-----------
+
+- For secondary process:
+
+ - Forked secondary process not supported.
+ - External memory unregistered in EAL memseg list cannot be used for DMA
+ unless such memory has been registered by ``mlx4_mr_update_ext_mp()`` in
+ primary process and remapped to the same virtual address in secondary
+ process. If the external memory is registered by primary process but has
+ different virtual address in secondary process, unexpected error may happen.
+
+- CRC stripping is supported by default and always reported as "true".
+ The ability to enable/disable CRC stripping requires OFED version
+ 4.3-1.5.0.0 and above or rdma-core version v18 and above.
+
+- TSO (Transmit Segmentation Offload) is supported in OFED version
+ 4.4 and above.
+
Prerequisites
-------------
allocations and initialization. The following dependencies are not part of
DPDK and must be installed separately:
-- **libibverbs**
+- **libibverbs** (provided by rdma-core package)
- User space verbs framework used by librte_pmd_mlx4. This library provides
+ User space verbs framework used by librte_net_mlx4. This library provides
a generic interface between the kernel and low-level user space drivers
such as libmlx4.
resources allocations) to be managed by the kernel and fast operations to
never leave user space.
-- **libmlx4**
+- **libmlx4** (provided by rdma-core package)
Low-level user space driver library for Mellanox ConnectX-3 devices,
it is automatically loaded by libibverbs.
This library basically implements send/receive calls to the hardware
queues.
-- **Kernel modules** (mlnx-ofed-kernel)
+- **Kernel modules**
They provide the kernel-side verbs API and low level device drivers that
manage actual hardware initialization and resources sharing with user
Both libraries are BSD and GPL licensed. Linux kernel modules are GPL
licensed.
-Currently supported by DPDK:
+Depending on system constraints and user preferences either RDMA core library
+with a recent enough Linux kernel release (recommended) or Mellanox OFED,
+which provides compatibility with older releases.
-- Mellanox OFED **4.1**.
-- Firmware version **2.36.5000** and above.
+Current RDMA core package and Linux kernel (recommended)
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
-Getting Mellanox OFED
-~~~~~~~~~~~~~~~~~~~~~
+- Minimal Linux kernel version: 4.14.
+- Minimal RDMA core version: v15 (see `RDMA core installation documentation`_).
+
+- Starting with rdma-core v21, static libraries can be built::
+
+ cd build
+ CFLAGS=-fPIC cmake -DIN_PLACE=1 -DENABLE_STATIC=1 -GNinja ..
+ ninja
+
+.. _`RDMA core installation documentation`: https://raw.githubusercontent.com/linux-rdma/rdma-core/master/README.md
-While these libraries and kernel modules are available on OpenFabrics
-Alliance's `website <https://www.openfabrics.org/>`_ and provided by package
-managers on most distributions, this PMD requires Ethernet extensions that
-may not be supported at the moment (this is a work in progress).
+.. _Mellanox_OFED_as_a_fallback:
-`Mellanox OFED
-<http://www.mellanox.com/page/products_dyn?product_family=26&mtag=linux_sw_drivers>`_
-includes the necessary support and should be used in the meantime. For DPDK,
-only libibverbs, libmlx4, mlnx-ofed-kernel packages and firmware updates are
-required from that distribution.
+Mellanox OFED as a fallback
+~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+- `Mellanox OFED`_ version: **4.4, 4.5, 4.6**.
+- firmware version: **2.42.5000** and above.
+
+.. _`Mellanox OFED`: http://www.mellanox.com/page/products_dyn?product_family=26&mtag=linux_sw_drivers
.. note::
this DPDK release was developed and tested against is strongly
recommended. Please check the `prerequisites`_.
-Supported NICs
---------------
+Installing Mellanox OFED
+^^^^^^^^^^^^^^^^^^^^^^^^
-* Mellanox(R) ConnectX(R)-3 Pro 40G MCX354A-FCC_Ax (2*40G)
-
-Quick Start Guide
------------------
-
-1. Download latest Mellanox OFED. For more info check the `prerequisites`_.
+1. Download latest Mellanox OFED.
2. Install the required libraries and kernel modules either by installing
only the required set, or by installing the entire Mellanox OFED:
- For bare metal use:
-
- .. code-block:: console
+ For bare metal use::
- ./mlnxofedinstall
+ ./mlnxofedinstall --dpdk --upstream-libs
- For SR-IOV hypervisors use:
+ For SR-IOV hypervisors use::
- .. code-block:: console
+ ./mlnxofedinstall --dpdk --upstream-libs --enable-sriov --hypervisor
- ./mlnxofedinstall --enable-sriov -hypervisor
+ For SR-IOV virtual machine use::
- For SR-IOV virtual machine use:
+ ./mlnxofedinstall --dpdk --upstream-libs --guest
- .. code-block:: console
-
- ./mlnxofedinstall --guest
-
-3. Verify the firmware is the correct one:
-
- .. code-block:: console
+3. Verify the firmware is the correct one::
ibv_devinfo
-4. Set all ports links to Ethernet, follow instructions on the screen:
-
- .. code-block:: console
+4. Set all ports links to Ethernet, follow instructions on the screen::
connectx_port_config
- Or in the manual way:
+5. Continue with :ref:`section 2 of the Quick Start Guide <QSG_2>`.
+
+.. _qsg:
+
+Quick Start Guide
+-----------------
- .. code-block:: console
+1. Set all ports links to Ethernet::
PCI=<NIC PCI address>
echo eth > "/sys/bus/pci/devices/$PCI/mlx4_port0"
echo eth > "/sys/bus/pci/devices/$PCI/mlx4_port1"
-5. In case of bare metal or hypervisor, configure optimized steering mode
- by adding the following line to ``/etc/modprobe.d/mlx4_core.conf``:
+ .. note::
+
+ If using Mellanox OFED one can permanently set the port link
+ to Ethernet using connectx_port_config tool provided by it.
+ :ref:`Mellanox_OFED_as_a_fallback`:
- .. code-block:: console
+.. _QSG_2:
+
+2. In case of bare metal or hypervisor, configure optimized steering mode
+ by adding the following line to ``/etc/modprobe.d/mlx4_core.conf``::
options mlx4_core log_num_mgm_entry_size=-7
If VLAN filtering is used, set log_num_mgm_entry_size=-1.
Performance degradation can occur on this case.
-6. Restart the driver:
-
- .. code-block:: console
+3. Restart the driver::
/etc/init.d/openibd restart
- or:
-
- .. code-block:: console
+ or::
service openibd restart
-7. Compile DPDK and you are ready to go. See instructions on
- :ref:`Development Kit Build System <Development_Kit_Build_System>`
+4. Install DPDK and you are ready to go.
+ See :doc:`compilation instructions <../linux_gsg/build_dpdk>`.
Performance tuning
------------------
-1. Verify the optimized steering mode is configured:
-
- .. code-block:: console
+1. Verify the optimized steering mode is configured::
cat /sys/module/mlx4_core/parameters/log_num_mgm_entry_size
-2. Use environment variable MLX4_INLINE_RECV_SIZE=64 to get maximum
- performance for 64B messages.
-
-3. Use the CPU near local NUMA node to which the PCIe adapter is connected,
+2. Use the CPU near local NUMA node to which the PCIe adapter is connected,
for better performance. For VMs, verify that the right CPU
- and NUMA node are pinned according to the above. Run:
+ and NUMA node are pinned according to the above. Run::
- .. code-block:: console
-
- lstopo-no-graphics
+ lstopo-no-graphics --merge
to identify the NUMA node to which the PCIe adapter is connected.
-4. If more than one adapter is used, and root complex capabilities allow
+3. If more than one adapter is used, and root complex capabilities allow
to put both adapters on the same NUMA node without PCI bandwidth degradation,
it is recommended to locate both adapters on the same NUMA node.
This in order to forward packets from one to the other without
NUMA performance penalty.
-5. Disable pause frames:
-
- .. code-block:: console
+4. Disable pause frames::
ethtool -A <netdev> rx off tx off
-6. Verify IO non-posted prefetch is disabled by default. This can be checked
+5. Verify IO non-posted prefetch is disabled by default. This can be checked
via the BIOS configuration. Please contact you server provider for more
information about the settings.
to set the PCI max read request parameter to 1K. This can be
done in the following way:
- To query the read request size use:
-
- .. code-block:: console
+ To query the read request size use::
setpci -s <NIC PCI address> 68.w
- If the output is different than 3XXX, set it by:
-
- .. code-block:: console
+ If the output is different than 3XXX, set it by::
setpci -s <NIC PCI address> 68.w=3XXX
The XXX can be different on different systems. Make sure to configure
according to the setpci output.
+6. To minimize overhead of searching Memory Regions:
+
+ - '--socket-mem' is recommended to pin memory by predictable amount.
+ - Configure per-lcore cache when creating Mempools for packet buffer.
+ - Refrain from dynamically allocating/freeing memory in run-time.
+
Usage example
-------------
This section demonstrates how to launch **testpmd** with Mellanox ConnectX-3
-devices managed by librte_pmd_mlx4.
+devices managed by librte_net_mlx4.
-#. Load the kernel modules:
-
- .. code-block:: console
+#. Load the kernel modules::
modprobe -a ib_uverbs mlx4_en mlx4_core mlx4_ib
Alternatively if MLNX_OFED is fully installed, the following script can
- be run:
-
- .. code-block:: console
+ be run::
/etc/init.d/openibd restart
not have to be loaded.
#. Make sure Ethernet interfaces are in working order and linked to kernel
- verbs. Related sysfs entries should be present:
-
- .. code-block:: console
+ verbs. Related sysfs entries should be present::
ls -d /sys/class/net/*/device/infiniband_verbs/uverbs* | cut -d / -f 5
- Example output:
-
- .. code-block:: console
+ Example output::
eth2
eth3
eth4
eth5
-#. Optionally, retrieve their PCI bus addresses for whitelisting:
-
- .. code-block:: console
+#. Optionally, retrieve their PCI bus addresses to be used with the allow argument::
{
for intf in eth2 eth3 eth4 eth5;
(cd "/sys/class/net/${intf}/device/" && pwd -P);
done;
} |
- sed -n 's,.*/\(.*\),-w \1,p'
-
- Example output:
+ sed -n 's,.*/\(.*\),-a \1,p'
- .. code-block:: console
+ Example output::
- -w 0000:83:00.0
- -w 0000:83:00.0
- -w 0000:84:00.0
- -w 0000:84:00.0
+ -a 0000:83:00.0
+ -a 0000:83:00.0
+ -a 0000:84:00.0
+ -a 0000:84:00.0
.. note::
There are only two distinct PCI bus addresses because the Mellanox
ConnectX-3 adapters installed on this system are dual port.
-#. Request huge pages:
-
- .. code-block:: console
-
- echo 1024 > /sys/kernel/mm/hugepages/hugepages-2048kB/nr_hugepages/nr_hugepages
-
-#. Start testpmd with basic parameters:
+#. Request huge pages::
- .. code-block:: console
+ dpdk-hugepages.py --setup 2G
- testpmd -l 8-15 -n 4 -w 0000:83:00.0 -w 0000:84:00.0 -- --rxq=2 --txq=2 -i
+#. Start testpmd with basic parameters::
- Example output:
+ dpdk-testpmd -l 8-15 -n 4 -a 0000:83:00.0 -a 0000:84:00.0 -- --rxq=2 --txq=2 -i
- .. code-block:: console
+ Example output::
[...]
EAL: PCI device 0000:83:00.0 on NUMA socket 1
- EAL: probe driver: 15b3:1007 librte_pmd_mlx4
- PMD: librte_pmd_mlx4: PCI information matches, using device "mlx4_0" (VF: false)
- PMD: librte_pmd_mlx4: 2 port(s) detected
- PMD: librte_pmd_mlx4: port 1 MAC address is 00:02:c9:b5:b7:50
- PMD: librte_pmd_mlx4: port 2 MAC address is 00:02:c9:b5:b7:51
+ EAL: probe driver: 15b3:1007 librte_net_mlx4
+ PMD: librte_net_mlx4: PCI information matches, using device "mlx4_0" (VF: false)
+ PMD: librte_net_mlx4: 2 port(s) detected
+ PMD: librte_net_mlx4: port 1 MAC address is 00:02:c9:b5:b7:50
+ PMD: librte_net_mlx4: port 2 MAC address is 00:02:c9:b5:b7:51
EAL: PCI device 0000:84:00.0 on NUMA socket 1
- EAL: probe driver: 15b3:1007 librte_pmd_mlx4
- PMD: librte_pmd_mlx4: PCI information matches, using device "mlx4_1" (VF: false)
- PMD: librte_pmd_mlx4: 2 port(s) detected
- PMD: librte_pmd_mlx4: port 1 MAC address is 00:02:c9:b5:ba:b0
- PMD: librte_pmd_mlx4: port 2 MAC address is 00:02:c9:b5:ba:b1
+ EAL: probe driver: 15b3:1007 librte_net_mlx4
+ PMD: librte_net_mlx4: PCI information matches, using device "mlx4_1" (VF: false)
+ PMD: librte_net_mlx4: 2 port(s) detected
+ PMD: librte_net_mlx4: port 1 MAC address is 00:02:c9:b5:ba:b0
+ PMD: librte_net_mlx4: port 2 MAC address is 00:02:c9:b5:ba:b1
Interactive-mode selected
Configuring Port 0 (socket 0)
- PMD: librte_pmd_mlx4: 0x867d60: TX queues number update: 0 -> 2
- PMD: librte_pmd_mlx4: 0x867d60: RX queues number update: 0 -> 2
+ PMD: librte_net_mlx4: 0x867d60: TX queues number update: 0 -> 2
+ PMD: librte_net_mlx4: 0x867d60: RX queues number update: 0 -> 2
Port 0: 00:02:C9:B5:B7:50
Configuring Port 1 (socket 0)
- PMD: librte_pmd_mlx4: 0x867da0: TX queues number update: 0 -> 2
- PMD: librte_pmd_mlx4: 0x867da0: RX queues number update: 0 -> 2
+ PMD: librte_net_mlx4: 0x867da0: TX queues number update: 0 -> 2
+ PMD: librte_net_mlx4: 0x867da0: RX queues number update: 0 -> 2
Port 1: 00:02:C9:B5:B7:51
Configuring Port 2 (socket 0)
- PMD: librte_pmd_mlx4: 0x867de0: TX queues number update: 0 -> 2
- PMD: librte_pmd_mlx4: 0x867de0: RX queues number update: 0 -> 2
+ PMD: librte_net_mlx4: 0x867de0: TX queues number update: 0 -> 2
+ PMD: librte_net_mlx4: 0x867de0: RX queues number update: 0 -> 2
Port 2: 00:02:C9:B5:BA:B0
Configuring Port 3 (socket 0)
- PMD: librte_pmd_mlx4: 0x867e20: TX queues number update: 0 -> 2
- PMD: librte_pmd_mlx4: 0x867e20: RX queues number update: 0 -> 2
+ PMD: librte_net_mlx4: 0x867e20: TX queues number update: 0 -> 2
+ PMD: librte_net_mlx4: 0x867e20: RX queues number update: 0 -> 2
Port 3: 00:02:C9:B5:BA:B1
Checking link statuses...
Port 0 Link Up - speed 10000 Mbps - full-duplex
git.droids-corp.org / dpdk.git / blobdiff