increment/decrement, count, drop, mark. For details please see :ref:`mlx5_offloads_support`.
- Flow insertion rate of more then million flows per second, when using Direct Rules.
- Support for multiple rte_flow groups.
+- Per packet no-inline hint flag to disable packet data copying into Tx descriptors.
- Hardware LRO.
+- Hairpin.
Limitations
-----------
Will match any ipv4 packet (VLAN included).
+- When using DV flow engine (``dv_flow_en`` = 1), flow pattern without VLAN item
+ will match untagged packets only.
+ The flow rule::
+
+ flow create 0 ingress pattern eth / ipv4 / end ...
+
+ Will match untagged packets only.
+ The flow rule::
+
+ flow create 0 ingress pattern eth / vlan / ipv4 / end ...
+
+ Will match tagged packets only, with any VLAN ID value.
+ The flow rule::
+
+ flow create 0 ingress pattern eth / vlan vid is 3 / ipv4 / end ...
+
+ Will only match tagged packets with VLAN ID 3.
+
- VLAN pop offload command:
- Flow rules having a VLAN pop offload command as one of their actions and
- Flows with a VXLAN Network Identifier equal (or ends to be equal)
to 0 are not supported.
-- VXLAN TSO and checksum offloads are not supported on VM.
-
- L3 VXLAN and VXLAN-GPE tunnels cannot be supported together with MPLSoGRE and MPLSoUDP.
- Match on Geneve header supports the following fields only:
- Match on GTP tunnel header item supports the following fields only:
+ - v_pt_rsv_flags: E flag, S flag, PN flag
- msg_type
- teid
To receive IPv6 Multicast messages on VM, explicitly set the relevant
MAC address using rte_eth_dev_mac_addr_add() API.
+- To support a mixed traffic pattern (some buffers from local host memory, some
+ buffers from other devices) with high bandwidth, a mbuf flag is used.
+
+ An application hints the PMD whether or not it should try to inline the
+ given mbuf data buffer. PMD should do the best effort to act upon this request.
+
+ The hint flag ``RTE_PMD_MLX5_FINE_GRANULARITY_INLINE`` is dynamic,
+ registered by application with rte_mbuf_dynflag_register(). This flag is
+ purely driver-specific and declared in PMD specific header ``rte_pmd_mlx5.h``,
+ which is intended to be used by the application.
+
+ To query the supported specific flags in runtime,
+ the function ``rte_pmd_mlx5_get_dyn_flag_names`` returns the array of
+ currently (over present hardware and configuration) supported specific flags.
+ The "not inline hint" feature operating flow is the following one:
+
+ - application starts
+ - probe the devices, ports are created
+ - query the port capabilities
+ - if port supporting the feature is found
+ - register dynamic flag ``RTE_PMD_MLX5_FINE_GRANULARITY_INLINE``
+ - application starts the ports
+ - on ``dev_start()`` PMD checks whether the feature flag is registered and
+ enables the feature support in datapath
+ - application might set the registered flag bit in ``ol_flags`` field
+ of mbuf being sent and PMD will handle ones appropriately.
+
- The amount of descriptors in Tx queue may be limited by data inline settings.
Inline data require the more descriptor building blocks and overall block
amount may exceed the hardware supported limits. The application should
reduce the requested Tx size or adjust data inline settings with
``txq_inline_max`` and ``txq_inline_mpw`` devargs keys.
+- To provide the packet send scheduling on mbuf timestamps the ``tx_pp``
+ parameter should be specified, RTE_MBUF_DYNFIELD_TIMESTAMP_NAME and
+ RTE_MBUF_DYNFLAG_TIMESTAMP_NAME should be registered by application.
+ When PMD sees the RTE_MBUF_DYNFLAG_TIMESTAMP_NAME set on the packet
+ being sent it tries to synchronize the time of packet appearing on
+ the wire with the specified packet timestamp. It the specified one
+ is in the past it should be ignored, if one is in the distant future
+ it should be capped with some reasonable value (in range of seconds).
+ These specific cases ("too late" and "distant future") can be optionally
+ reported via device xstats to assist applications to detect the
+ time-related problems.
+
+ The timestamp upper "too-distant-future" limit
+ at the moment of invoking the Tx burst routine
+ can be estimated as ``tx_pp`` option (in nanoseconds) multiplied by 2^23.
+ Please note, for the testpmd txonly mode,
+ the limit is deduced from the expression::
+
+ (n_tx_descriptors / burst_size + 1) * inter_burst_gap
+
+ There is no any packet reordering according timestamps is supposed,
+ neither within packet burst, nor between packets, it is an entirely
+ application responsibility to generate packets and its timestamps
+ in desired order. The timestamps can be put only in the first packet
+ in the burst providing the entire burst scheduling.
+
- E-Switch decapsulation Flow:
- can be applied to PF port only.
TCP header (122B).
- Rx queue with LRO offload enabled, receiving a non-LRO packet, can forward
it with size limited to max LRO size, not to max RX packet length.
+ - LRO can be used with outer header of TCP packets of the standard format:
+ eth (with or without vlan) / ipv4 or ipv6 / tcp / payload
+
+ Other TCP packets (e.g. with MPLS label) received on Rx queue with LRO enabled, will be received with bad checksum.
+
+- CRC:
+
+ - ``DEV_RX_OFFLOAD_KEEP_CRC`` cannot be supported with decapsulation
+ for some NICs (such as ConnectX-6 Dx and BlueField 2).
+ The capability bit ``scatter_fcs_w_decap_disable`` shows NIC support.
Statistics
----------
- **ethtool** operations on related kernel interfaces also affect the PMD.
+Run as non-root
+^^^^^^^^^^^^^^^
+
+In order to run as a non-root user,
+some capabilities must be granted to the application::
+
+ setcap cap_sys_admin,cap_net_admin,cap_net_raw,cap_ipc_lock+ep <dpdk-app>
+
+Below are the reasons of the need for each capability:
+
+``cap_sys_admin``
+ When using physical addresses (PA mode), with Linux >= 4.0,
+ for access to ``/proc/self/pagemap``.
+
+``cap_net_admin``
+ For device configuration.
+
+``cap_net_raw``
+ For raw ethernet queue allocation through kernel driver.
+
+``cap_ipc_lock``
+ For DMA memory pinning.
+
+Driver options
+^^^^^^^^^^^^^^
+
- ``rxq_cqe_comp_en`` parameter [int]
A nonzero value enables the compression of CQE on RX side. This feature
A nonzero value enables configuring Multi-Packet Rx queues. Rx queue is
configured as Multi-Packet RQ if the total number of Rx queues is
- ``rxqs_min_mprq`` or more and Rx scatter isn't configured. Disabled by
- default.
+ ``rxqs_min_mprq`` or more. Disabled by default.
Multi-Packet Rx Queue (MPRQ a.k.a Striding RQ) can further save PCIe bandwidth
by posting a single large buffer for multiple packets. Instead of posting a
The size of Rx queue should be bigger than the number of strides.
+- ``mprq_log_stride_size`` parameter [int]
+
+ Log 2 of the size of a stride for Multi-Packet Rx queue. Configuring a smaller
+ stride size can save some memory and reduce probability of a depletion of all
+ available strides due to unreleased packets by an application. If configured
+ value is not in the range of device capability, the default value will be set
+ with a warning message. The default value is 11 which is 2048 bytes per a
+ stride, valid only if ``mprq_en`` is set. With ``mprq_log_stride_size`` set
+ it is possible for a packet to span across multiple strides. This mode allows
+ support of jumbo frames (9K) with MPRQ. The memcopy of some packets (or part
+ of a packet if Rx scatter is configured) may be required in case there is no
+ space left for a head room at the end of a stride which incurs some
+ performance penalty.
+
- ``mprq_max_memcpy_len`` parameter [int]
The maximum length of packet to memcpy in case of Multi-Packet Rx queue. Rx
variable "MLX5_SHUT_UP_BF" value is used. If there is no "MLX5_SHUT_UP_BF",
the default ``tx_db_nc`` value is zero for ARM64 hosts and one for others.
+- ``tx_pp`` parameter [int]
+
+ If a nonzero value is specified the driver creates all necessary internal
+ objects to provide accurate packet send scheduling on mbuf timestamps.
+ The positive value specifies the scheduling granularity in nanoseconds,
+ the packet send will be accurate up to specified digits. The allowed range is
+ from 500 to 1 million of nanoseconds. The negative value specifies the module
+ of granularity and engages the special test mode the check the schedule rate.
+ By default (if the ``tx_pp`` is not specified) send scheduling on timestamps
+ feature is disabled.
+
+- ``tx_skew`` parameter [int]
+
+ The parameter adjusts the send packet scheduling on timestamps and represents
+ the average delay between beginning of the transmitting descriptor processing
+ by the hardware and appearance of actual packet data on the wire. The value
+ should be provided in nanoseconds and is valid only if ``tx_pp`` parameter is
+ specified. The default value is zero.
+
- ``tx_vec_en`` parameter [int]
A nonzero value enables Tx vector on ConnectX-5, ConnectX-6, ConnectX-6 Dx
Enabled by default if supported.
+- ``lacp_by_user`` parameter [int]
+
+ A nonzero value enables the control of LACP traffic by the user application.
+ When a bond exists in the driver, by default it should be managed by the
+ kernel and therefore LACP traffic should be steered to the kernel.
+ If this devarg is set to 1 it will allow the user to manage the bond by
+ itself and not steer LACP traffic to the kernel.
+
+ Disabled by default (set to 0).
+
- ``mr_ext_memseg_en`` parameter [int]
A nonzero value enables extending memseg when registering DMA memory. If
If this parameter is not specified, by default PMD will set
the smallest value supported by HW.
+- ``hp_buf_log_sz`` parameter [int]
+
+ The total data buffer size of a hairpin queue (logarithmic form), in bytes.
+ PMD will set the data buffer size to 2 ** ``hp_buf_log_sz``, both for RX & TX.
+ The capacity of the value is specified by the firmware and the initialization
+ will get a failure if it is out of scope.
+ The range of the value is from 11 to 19 right now, and the supported frame
+ size of a single packet for hairpin is from 512B to 128KB. It might change if
+ different firmware release is being used. By using a small value, it could
+ reduce memory consumption but not work with a large frame. If the value is
+ too large, the memory consumption will be high and some potential performance
+ degradation will be introduced.
+ By default, the PMD will set this value to 16, which means that 9KB jumbo
+ frames will be supported.
+
+- ``reclaim_mem_mode`` parameter [int]
+
+ Cache some resources in flow destroy will help flow recreation more efficient.
+ While some systems may require the all the resources can be reclaimed after
+ flow destroyed.
+ The parameter ``reclaim_mem_mode`` provides the option for user to configure
+ if the resource cache is needed or not.
+
+ There are three options to choose:
+
+ - 0. It means the flow resources will be cached as usual. The resources will
+ be cached, helpful with flow insertion rate.
+
+ - 1. It will only enable the DPDK PMD level resources reclaim.
+
+ - 2. Both DPDK PMD level and rdma-core low level will be configured as
+ reclaimed mode.
+
+ By default, the PMD will set this value to 0.
+
+- ``sys_mem_en`` parameter [int]
+
+ A non-zero value enables the PMD memory management allocating memory
+ from system by default, without explicit rte memory flag.
+
+ By default, the PMD will set this value to 0.
+
+- ``decap_en`` parameter [int]
+
+ Some devices do not support FCS (frame checksum) scattering for
+ tunnel-decapsulated packets.
+ If set to 0, this option forces the FCS feature and rejects tunnel
+ decapsulation in the flow engine for such devices.
+
+ By default, the PMD will set this value to 1.
+
.. _mlx5_firmware_config:
Firmware configuration
IP_OVER_VXLAN_EN=1
IP_OVER_VXLAN_PORT=<udp dport>
+- enable VXLAN-GPE tunnel flow matching::
+
+ FLEX_PARSER_PROFILE_ENABLE=0
+ or
+ FLEX_PARSER_PROFILE_ENABLE=2
+
- enable IP-in-IP tunnel flow matching::
FLEX_PARSER_PROFILE_ENABLE=0
- enable Geneve flow matching::
FLEX_PARSER_PROFILE_ENABLE=0
+ or
+ FLEX_PARSER_PROFILE_ENABLE=1
- enable GTP flow matching::
FLEX_PARSER_PROFILE_ENABLE=3
+- enable eCPRI flow matching::
+
+ FLEX_PARSER_PROFILE_ENABLE=4
+ PROG_PARSE_GRAPH=1
+
Prerequisites
-------------
Mellanox OFED/EN
^^^^^^^^^^^^^^^^
-- Mellanox OFED version: ** 4.5, 4.6** /
- Mellanox EN version: **4.5, 4.6**
+- Mellanox OFED version: **4.5** and above /
+ Mellanox EN version: **4.5** and above
- firmware version:
- ConnectX-4: **12.21.1000** and above.
- ConnectX-4 Lx: **14.21.1000** and above.
- ConnectX-5: **16.21.1000** and above.
- ConnectX-5 Ex: **16.21.1000** and above.
- - ConnectX-6: **20.99.5374** and above.
+ - ConnectX-6: **20.27.0090** and above.
- ConnectX-6 Dx: **22.27.0090** and above.
- BlueField: **18.25.1010** and above.
| | | ConnectX-5 | | ConnectX-5 |
+-----------------------+-----------------+-----------------+
+Notes for metadata
+------------------
+
+MARK and META items are interrelated with datapath - they might move from/to
+the applications in mbuf fields. Hence, zero value for these items has the
+special meaning - it means "no metadata are provided", not zero values are
+treated by applications and PMD as valid ones.
+
+Moreover in the flow engine domain the value zero is acceptable to match and
+set, and we should allow to specify zero values as rte_flow parameters for the
+META and MARK items and actions. In the same time zero mask has no meaning and
+should be rejected on validation stage.
+
+Notes for rte_flow
+------------------
+
+Flows are not cached in the driver.
+When stopping a device port, all the flows created on this port from the
+application will be flushed automatically in the background.
+After stopping the device port, all flows on this port become invalid and
+not represented in the system.
+All references to these flows held by the application should be discarded
+directly but neither destroyed nor flushed.
+
+The application should re-create the flows as required after the port restart.
+
Notes for testpmd
-----------------