- Support for multiple rte_flow groups.
- Per packet no-inline hint flag to disable packet data copying into Tx descriptors.
- Hardware LRO.
+- Hairpin.
Limitations
-----------
Will match any ipv4 packet (VLAN included).
+- When using DV flow engine (``dv_flow_en`` = 1), flow pattern without VLAN item
+ will match untagged packets only.
+ The flow rule::
+
+ flow create 0 ingress pattern eth / ipv4 / end ...
+
+ Will match untagged packets only.
+ The flow rule::
+
+ flow create 0 ingress pattern eth / vlan / ipv4 / end ...
+
+ Will match tagged packets only, with any VLAN ID value.
+ The flow rule::
+
+ flow create 0 ingress pattern eth / vlan vid is 3 / ipv4 / end ...
+
+ Will only match tagged packets with VLAN ID 3.
+
- VLAN pop offload command:
- Flow rules having a VLAN pop offload command as one of their actions and
- Flows with a VXLAN Network Identifier equal (or ends to be equal)
to 0 are not supported.
-- VXLAN TSO and checksum offloads are not supported on VM.
-
- L3 VXLAN and VXLAN-GPE tunnels cannot be supported together with MPLSoGRE and MPLSoUDP.
- Match on Geneve header supports the following fields only:
- Match on GTP tunnel header item supports the following fields only:
+ - v_pt_rsv_flags: E flag, S flag, PN flag
- msg_type
- teid
reduce the requested Tx size or adjust data inline settings with
``txq_inline_max`` and ``txq_inline_mpw`` devargs keys.
+- To provide the packet send scheduling on mbuf timestamps the ``tx_pp``
+ parameter should be specified, RTE_MBUF_DYNFIELD_TIMESTAMP_NAME and
+ RTE_MBUF_DYNFLAG_TIMESTAMP_NAME should be registered by application.
+ When PMD sees the RTE_MBUF_DYNFLAG_TIMESTAMP_NAME set on the packet
+ being sent it tries to synchronize the time of packet appearing on
+ the wire with the specified packet timestamp. It the specified one
+ is in the past it should be ignored, if one is in the distant future
+ it should be capped with some reasonable value (in range of seconds).
+ These specific cases ("too late" and "distant future") can be optionally
+ reported via device xstats to assist applications to detect the
+ time-related problems.
+
+ The timestamp upper "too-distant-future" limit
+ at the moment of invoking the Tx burst routine
+ can be estimated as ``tx_pp`` option (in nanoseconds) multiplied by 2^23.
+ Please note, for the testpmd txonly mode,
+ the limit is deduced from the expression::
+
+ (n_tx_descriptors / burst_size + 1) * inter_burst_gap
+
+ There is no any packet reordering according timestamps is supposed,
+ neither within packet burst, nor between packets, it is an entirely
+ application responsibility to generate packets and its timestamps
+ in desired order. The timestamps can be put only in the first packet
+ in the burst providing the entire burst scheduling.
+
- E-Switch decapsulation Flow:
- can be applied to PF port only.
TCP header (122B).
- Rx queue with LRO offload enabled, receiving a non-LRO packet, can forward
it with size limited to max LRO size, not to max RX packet length.
+ - LRO can be used with outer header of TCP packets of the standard format:
+ eth (with or without vlan) / ipv4 or ipv6 / tcp / payload
+
+ Other TCP packets (e.g. with MPLS label) received on Rx queue with LRO enabled, will be received with bad checksum.
+
+- CRC:
+
+ - ``DEV_RX_OFFLOAD_KEEP_CRC`` cannot be supported with decapsulation
+ for some NICs (such as ConnectX-6 Dx and BlueField 2).
+ The capability bit ``scatter_fcs_w_decap_disable`` shows NIC support.
Statistics
----------
- **ethtool** operations on related kernel interfaces also affect the PMD.
+Run as non-root
+^^^^^^^^^^^^^^^
+
+In order to run as a non-root user,
+some capabilities must be granted to the application::
+
+ setcap cap_sys_admin,cap_net_admin,cap_net_raw,cap_ipc_lock+ep <dpdk-app>
+
+Below are the reasons of the need for each capability:
+
+``cap_sys_admin``
+ When using physical addresses (PA mode), with Linux >= 4.0,
+ for access to ``/proc/self/pagemap``.
+
+``cap_net_admin``
+ For device configuration.
+
+``cap_net_raw``
+ For raw ethernet queue allocation through kernel driver.
+
+``cap_ipc_lock``
+ For DMA memory pinning.
+
+Driver options
+^^^^^^^^^^^^^^
+
- ``rxq_cqe_comp_en`` parameter [int]
A nonzero value enables the compression of CQE on RX side. This feature
A nonzero value enables configuring Multi-Packet Rx queues. Rx queue is
configured as Multi-Packet RQ if the total number of Rx queues is
- ``rxqs_min_mprq`` or more and Rx scatter isn't configured. Disabled by
- default.
+ ``rxqs_min_mprq`` or more. Disabled by default.
Multi-Packet Rx Queue (MPRQ a.k.a Striding RQ) can further save PCIe bandwidth
by posting a single large buffer for multiple packets. Instead of posting a
The size of Rx queue should be bigger than the number of strides.
+- ``mprq_log_stride_size`` parameter [int]
+
+ Log 2 of the size of a stride for Multi-Packet Rx queue. Configuring a smaller
+ stride size can save some memory and reduce probability of a depletion of all
+ available strides due to unreleased packets by an application. If configured
+ value is not in the range of device capability, the default value will be set
+ with a warning message. The default value is 11 which is 2048 bytes per a
+ stride, valid only if ``mprq_en`` is set. With ``mprq_log_stride_size`` set
+ it is possible for a packet to span across multiple strides. This mode allows
+ support of jumbo frames (9K) with MPRQ. The memcopy of some packets (or part
+ of a packet if Rx scatter is configured) may be required in case there is no
+ space left for a head room at the end of a stride which incurs some
+ performance penalty.
+
- ``mprq_max_memcpy_len`` parameter [int]
The maximum length of packet to memcpy in case of Multi-Packet Rx queue. Rx
variable "MLX5_SHUT_UP_BF" value is used. If there is no "MLX5_SHUT_UP_BF",
the default ``tx_db_nc`` value is zero for ARM64 hosts and one for others.
+- ``tx_pp`` parameter [int]
+
+ If a nonzero value is specified the driver creates all necessary internal
+ objects to provide accurate packet send scheduling on mbuf timestamps.
+ The positive value specifies the scheduling granularity in nanoseconds,
+ the packet send will be accurate up to specified digits. The allowed range is
+ from 500 to 1 million of nanoseconds. The negative value specifies the module
+ of granularity and engages the special test mode the check the schedule rate.
+ By default (if the ``tx_pp`` is not specified) send scheduling on timestamps
+ feature is disabled.
+
+- ``tx_skew`` parameter [int]
+
+ The parameter adjusts the send packet scheduling on timestamps and represents
+ the average delay between beginning of the transmitting descriptor processing
+ by the hardware and appearance of actual packet data on the wire. The value
+ should be provided in nanoseconds and is valid only if ``tx_pp`` parameter is
+ specified. The default value is zero.
+
- ``tx_vec_en`` parameter [int]
A nonzero value enables Tx vector on ConnectX-5, ConnectX-6, ConnectX-6 Dx
Enabled by default if supported.
+- ``lacp_by_user`` parameter [int]
+
+ A nonzero value enables the control of LACP traffic by the user application.
+ When a bond exists in the driver, by default it should be managed by the
+ kernel and therefore LACP traffic should be steered to the kernel.
+ If this devarg is set to 1 it will allow the user to manage the bond by
+ itself and not steer LACP traffic to the kernel.
+
+ Disabled by default (set to 0).
+
- ``mr_ext_memseg_en`` parameter [int]
A nonzero value enables extending memseg when registering DMA memory. If
If this parameter is not specified, by default PMD will set
the smallest value supported by HW.
+- ``hp_buf_log_sz`` parameter [int]
+
+ The total data buffer size of a hairpin queue (logarithmic form), in bytes.
+ PMD will set the data buffer size to 2 ** ``hp_buf_log_sz``, both for RX & TX.
+ The capacity of the value is specified by the firmware and the initialization
+ will get a failure if it is out of scope.
+ The range of the value is from 11 to 19 right now, and the supported frame
+ size of a single packet for hairpin is from 512B to 128KB. It might change if
+ different firmware release is being used. By using a small value, it could
+ reduce memory consumption but not work with a large frame. If the value is
+ too large, the memory consumption will be high and some potential performance
+ degradation will be introduced.
+ By default, the PMD will set this value to 16, which means that 9KB jumbo
+ frames will be supported.
+
+- ``reclaim_mem_mode`` parameter [int]
+
+ Cache some resources in flow destroy will help flow recreation more efficient.
+ While some systems may require the all the resources can be reclaimed after
+ flow destroyed.
+ The parameter ``reclaim_mem_mode`` provides the option for user to configure
+ if the resource cache is needed or not.
+
+ There are three options to choose:
+
+ - 0. It means the flow resources will be cached as usual. The resources will
+ be cached, helpful with flow insertion rate.
+
+ - 1. It will only enable the DPDK PMD level resources reclaim.
+
+ - 2. Both DPDK PMD level and rdma-core low level will be configured as
+ reclaimed mode.
+
+ By default, the PMD will set this value to 0.
+
+- ``sys_mem_en`` parameter [int]
+
+ A non-zero value enables the PMD memory management allocating memory
+ from system by default, without explicit rte memory flag.
+
+ By default, the PMD will set this value to 0.
+
+- ``decap_en`` parameter [int]
+
+ Some devices do not support FCS (frame checksum) scattering for
+ tunnel-decapsulated packets.
+ If set to 0, this option forces the FCS feature and rejects tunnel
+ decapsulation in the flow engine for such devices.
+
+ By default, the PMD will set this value to 1.
+
.. _mlx5_firmware_config:
Firmware configuration
FLEX_PARSER_PROFILE_ENABLE=3
+- enable eCPRI flow matching::
+
+ FLEX_PARSER_PROFILE_ENABLE=4
+ PROG_PARSE_GRAPH=1
+
Prerequisites
-------------
| | | ConnectX-5 | | ConnectX-5 |
+-----------------------+-----------------+-----------------+
+Notes for metadata
+------------------
+
+MARK and META items are interrelated with datapath - they might move from/to
+the applications in mbuf fields. Hence, zero value for these items has the
+special meaning - it means "no metadata are provided", not zero values are
+treated by applications and PMD as valid ones.
+
+Moreover in the flow engine domain the value zero is acceptable to match and
+set, and we should allow to specify zero values as rte_flow parameters for the
+META and MARK items and actions. In the same time zero mask has no meaning and
+should be rejected on validation stage.
+
+Notes for rte_flow
+------------------
+
+Flows are not cached in the driver.
+When stopping a device port, all the flows created on this port from the
+application will be flushed automatically in the background.
+After stopping the device port, all flows on this port become invalid and
+not represented in the system.
+All references to these flows held by the application should be discarded
+directly but neither destroyed nor flushed.
+
+The application should re-create the flows as required after the port restart.
+
Notes for testpmd
-----------------