reduce the requested Tx size or adjust data inline settings with
``txq_inline_max`` and ``txq_inline_mpw`` devargs keys.
+- To provide the packet send scheduling on mbuf timestamps the ``tx_pp``
+ parameter should be specified, RTE_MBUF_DYNFIELD_TIMESTAMP_NAME and
+ RTE_MBUF_DYNFLAG_TIMESTAMP_NAME should be registered by application.
+ When PMD sees the RTE_MBUF_DYNFLAG_TIMESTAMP_NAME set on the packet
+ being sent it tries to synchronize the time of packet appearing on
+ the wire with the specified packet timestamp. It the specified one
+ is in the past it should be ignored, if one is in the distant future
+ it should be capped with some reasonable value (in range of seconds).
+ These specific cases ("too late" and "distant future") can be optionally
+ reported via device xstats to assist applications to detect the
+ time-related problems.
+
+ There is no any packet reordering according timestamps is supposed,
+ neither within packet burst, nor between packets, it is an entirely
+ application responsibility to generate packets and its timestamps
+ in desired order. The timestamps can be put only in the first packet
+ in the burst providing the entire burst scheduling.
+
- E-Switch decapsulation Flow:
- can be applied to PF port only.
Other TCP packets (e.g. with MPLS label) received on Rx queue with LRO enabled, will be received with bad checksum.
+- CRC:
+
+ - ``DEV_RX_OFFLOAD_KEEP_CRC`` cannot be supported with decapsulation
+ for some NICs (such as ConnectX-6 Dx and BlueField 2).
+ The capability bit ``scatter_fcs_w_decap_disable`` shows NIC support.
+
Statistics
----------
value is not in the range of device capability, the default value will be set
with a warning message. The default value is 11 which is 2048 bytes per a
stride, valid only if ``mprq_en`` is set. With ``mprq_log_stride_size`` set
- it is possible for a pcaket to span across multiple strides. This mode allows
+ it is possible for a packet to span across multiple strides. This mode allows
support of jumbo frames (9K) with MPRQ. The memcopy of some packets (or part
of a packet if Rx scatter is configured) may be required in case there is no
space left for a head room at the end of a stride which incurs some
variable "MLX5_SHUT_UP_BF" value is used. If there is no "MLX5_SHUT_UP_BF",
the default ``tx_db_nc`` value is zero for ARM64 hosts and one for others.
+- ``tx_pp`` parameter [int]
+
+ If a nonzero value is specified the driver creates all necessary internal
+ objects to provide accurate packet send scheduling on mbuf timestamps.
+ The positive value specifies the scheduling granularity in nanoseconds,
+ the packet send will be accurate up to specified digits. The allowed range is
+ from 500 to 1 million of nanoseconds. The negative value specifies the module
+ of granularity and engages the special test mode the check the schedule rate.
+ By default (if the ``tx_pp`` is not specified) send scheduling on timestamps
+ feature is disabled.
+
+- ``tx_skew`` parameter [int]
+
+ The parameter adjusts the send packet scheduling on timestamps and represents
+ the average delay between beginning of the transmitting descriptor processing
+ by the hardware and appearance of actual packet data on the wire. The value
+ should be provided in nanoseconds and is valid only if ``tx_pp`` parameter is
+ specified. The default value is zero.
+
- ``tx_vec_en`` parameter [int]
A nonzero value enables Tx vector on ConnectX-5, ConnectX-6, ConnectX-6 Dx
Enabled by default if supported.
+- ``lacp_by_user`` parameter [int]
+
+ A nonzero value enables the control of LACP traffic by the user application.
+ When a bond exists in the driver, by default it should be managed by the
+ kernel and therefore LACP traffic should be steered to the kernel.
+ If this devarg is set to 1 it will allow the user to manage the bond by
+ itself and not steer LACP traffic to the kernel.
+
+ Disabled by default (set to 0).
+
- ``mr_ext_memseg_en`` parameter [int]
A nonzero value enables extending memseg when registering DMA memory. If
By default, the PMD will set this value to 16, which means that 9KB jumbo
frames will be supported.
+- ``reclaim_mem_mode`` parameter [int]
+
+ Cache some resources in flow destroy will help flow recreation more efficient.
+ While some systems may require the all the resources can be reclaimed after
+ flow destroyed.
+ The parameter ``reclaim_mem_mode`` provides the option for user to configure
+ if the resource cache is needed or not.
+
+ There are three options to choose:
+
+ - 0. It means the flow resources will be cached as usual. The resources will
+ be cached, helpful with flow insertion rate.
+
+ - 1. It will only enable the DPDK PMD level resources reclaim.
+
+ - 2. Both DPDK PMD level and rdma-core low level will be configured as
+ reclaimed mode.
+
+ By default, the PMD will set this value to 0.
+
+- ``sys_mem_en`` parameter [int]
+
+ A non-zero value enables the PMD memory management allocating memory
+ from system by default, without explicit rte memory flag.
+
+ By default, the PMD will set this value to 0.
+
+- ``decap_en`` parameter [int]
+
+ Some devices do not support FCS (frame checksum) scattering for
+ tunnel-decapsulated packets.
+ If set to 0, this option forces the FCS feature and rejects tunnel
+ decapsulation in the flow engine for such devices.
+
+ By default, the PMD will set this value to 1.
+
.. _mlx5_firmware_config:
Firmware configuration
FLEX_PARSER_PROFILE_ENABLE=3
+- enable eCPRI flow matching::
+
+ FLEX_PARSER_PROFILE_ENABLE=4
+ PROG_PARSE_GRAPH=1
+
Prerequisites
-------------
git.droids-corp.org / dpdk.git / blobdiff