* kvargs: The function ``rte_kvargs_process`` will get a new parameter
for returning key match count. It will ease handling of no-match case.
-* eal: The ``attr_value`` parameter of ``rte_service_attr_get()``
- will be changed from ``uint32_t *`` to ``uint64_t *``
- as the attributes are of type ``uint64_t``.
+* eal: The function ``rte_eal_remote_launch`` will return new error codes
+ after read or write error on the pipe, instead of calling ``rte_panic``.
* eal: both declaring and identifying devices will be streamlined in v18.11.
New functions will appear to query a specific port from buses, classes of
+ ``rte_eal_devargs_type_count``
-* pci: Several exposed functions are misnamed.
- The following functions are deprecated starting from v17.11 and are replaced:
-
- - ``eal_parse_pci_BDF`` replaced by ``rte_pci_addr_parse``
- - ``eal_parse_pci_DomBDF`` replaced by ``rte_pci_addr_parse``
- - ``rte_eal_compare_pci_addr`` replaced by ``rte_pci_addr_cmp``
+* vfio: removal of ``rte_vfio_dma_map`` and ``rte_vfio_dma_unmap`` APIs which
+ have been replaced with ``rte_dev_dma_map`` and ``rte_dev_dma_unmap``
+ functions. The due date for the removal targets DPDK 20.02.
* dpaa2: removal of ``rte_dpaa2_memsegs`` structure which has been replaced
by a pa-va search library. This structure was earlier being used for holding
structure would be made internal (or removed if all dependencies are cleared)
in future releases.
+* net: The Ethernet address and header definitions will change
+ attributes. The Ethernet address struct will no longer be marked as
+ packed since the packed attribute is meaningless on a byte
+ array. The Ethernet header will be marked as aligned on a 2-byte
+ boundary and will no longer have the packed attribute. This allows
+ for efficient access on CPU architectures where unaligned access is
+ expensive. These changes should not impact normal usage because drivers
+ naturally align the Ethernet header on receive and all known
+ encapsulations preserve the alignment of the header.
+
+* ethdev: The function ``rte_eth_dev_count`` will be removed in DPDK 20.02.
+ It is replaced by the function ``rte_eth_dev_count_avail``.
+ If the intent is to iterate over ports, ``RTE_ETH_FOREACH_*`` macros
+ are better port iterators.
+
* ethdev: the legacy filter API, including
``rte_eth_dev_filter_supported()``, ``rte_eth_dev_filter_ctrl()`` as well
as filter types MACVLAN, ETHERTYPE, FLEXIBLE, SYN, NTUPLE, TUNNEL, FDIR,
Target release for removal of the legacy API will be defined once most
PMDs have switched to rte_flow.
-* ethdev: Maximum and minimum MTU values vary between hardware devices. In
- hardware agnostic DPDK applications access to such information would allow
- a more accurate way of validating and setting supported MTU values on a per
- device basis rather than using a defined default for all devices. To
- resolve this, the following members will be added to ``rte_eth_dev_info``.
- Note: these can be added to fit a hole in the existing structure for amd64
- but not for 32-bit, as such ABI change will occur as size of the structure
- will increase.
-
- - Member ``uint16_t min_mtu`` the minimum MTU allowed.
- - Member ``uint16_t max_mtu`` the maximum MTU allowed.
-
-* crypto/aesni_mb: the minimum supported intel-ipsec-mb library version will be
- changed from 0.49.0 to 0.52.0.
+* ethdev: Update API functions returning ``void`` to return ``int`` with
+ negative errno values to indicate various error conditions (e.g.
+ invalid port ID, unsupported operation, failed operation):
+
+ - ``rte_eth_dev_stop``
+ - ``rte_eth_dev_close``
+
+* ethdev: New offload flags ``DEV_RX_OFFLOAD_RSS_HASH`` and
+ ``DEV_RX_OFFLOAD_FLOW_MARK`` will be added in 19.11.
+ This will allow application to enable or disable PMDs from updating
+ ``rte_mbuf::hash::rss`` and ``rte_mbuf::hash::fdir`` respectively.
+ This scheme will allow PMDs to avoid writes to ``rte_mbuf`` fields on Rx and
+ thereby improve Rx performance if application wishes do so.
+ In 19.11 PMDs will still update the fields even when the offloads are not
+ enabled.
+
+* ethdev: New function ``rte_eth_dev_set_supported_ptypes`` will be added in
+ 19.11.
+ This will allow application to request PMD to set specific ptypes defined
+ through ``rte_eth_dev_set_supported_ptypes`` in ``rte_mbuf::packet_type``.
+ If application doesn't want any ptype information it can call
+ ``rte_eth_dev_set_supported_ptypes(ethdev_id, RTE_PTYPE_UNKNOWN)`` and PMD
+ will set ``rte_mbuf::packet_type`` to ``0``.
+ If application doesn't call ``rte_eth_dev_set_supported_ptypes`` PMD can
+ return ``rte_mbuf::packet_type`` with ``rte_eth_dev_get_supported_ptypes``.
+ If application is interested only in L2/L3 layer, it can inform the PMD
+ to update ``rte_mbuf::packet_type`` with L2/L3 ptype by calling
+ ``rte_eth_dev_set_supported_ptypes(ethdev_id, RTE_PTYPE_L2_MASK | RTE_PTYPE_L3_MASK)``.
+ This scheme will allow PMDs to avoid lookup to internal ptype table on Rx and
+ thereby improve Rx performance if application wishes do so.
+
+* ethdev: New 32-bit fields may be added for maximum LRO session size, in
+ struct ``rte_eth_dev_info`` for the port capability and in struct
+ ``rte_eth_rxmode`` for the port configuration.
+
+* cryptodev: support for using IV with all sizes is added, J0 still can
+ be used but only when IV length in following structs ``rte_crypto_auth_xform``,
+ ``rte_crypto_aead_xform`` is set to zero. When IV length is greater or equal
+ to one it means it represents IV, when is set to zero it means J0 is used
+ directly, in this case 16 bytes of J0 need to be passed.
+
+* sched: To allow more traffic classes, flexible mapping of pipe queues to
+ traffic classes, and subport level configuration of pipes and queues
+ changes will be made to macros, data structures and API functions defined
+ in "rte_sched.h". These changes are aligned to improvements suggested in the
+ RFC https://mails.dpdk.org/archives/dev/2018-November/120035.html.
+
+* metrics: The function ``rte_metrics_init`` will have a non-void return
+ in order to notify errors instead of calling ``rte_exit``.
+
+* power: ``rte_power_set_env`` function will no longer return 0 on attempt
+ to set new power environment if power environment was already initialized.
+ In this case the function will return -1 unless the environment is unset first
+ (using ``rte_power_unset_env``). Other function usage scenarios will not change.