net/mlx5: support power monitoring

[dpdk.git] / doc / guides / sample_app_ug / ip_reassembly.rst

diff --git a/doc/guides/sample_app_ug/ip_reassembly.rst b/doc/guides/sample_app_ug/ip_reassembly.rst
index a628b63..e72c849 100644 (file)
--- a/doc/guides/sample_app_ug/ip_reassembly.rst
+++ b/doc/guides/sample_app_ug/ip_reassembly.rst
@@ -42,7 +42,7 @@ The application has a number of command line options:
 
 .. code-block:: console
 
-    ./build/ip_reassembly [EAL options] -- -p PORTMASK [-q NQ] [--maxflows=FLOWS>] [--flowttl=TTL[(s|ms)]]
+    ./<build_dir>/examples/dpdk-ip_reassembly [EAL options] -- -p PORTMASK [-q NQ] [--maxflows=FLOWS>] [--flowttl=TTL[(s|ms)]]
 
 where:
 
@@ -61,7 +61,7 @@ To run the example in linux environment with 2 lcores (2,4) over 2 ports(0,2) wi
 
 .. code-block:: console
 
-    ./build/ip_reassembly -l 2,4 -n 3 -- -p 5
+    ./<build_dir>/examples/dpdk-ip_reassembly -l 2,4 -n 3 -- -p 5
     EAL: coremask set to 14
     EAL: Detected lcore 0 on socket 0
     EAL: Detected lcore 1 on socket 1
@@ -92,7 +92,7 @@ To run the example in linux environment with 1 lcore (4) over 2 ports(0,2) with
 
 .. code-block:: console
 
-    ./build/ip_reassembly -l 4 -n 3 -- -p 5 -q 2
+    ./<build_dir>/examples/dpdk-ip_reassembly -l 4 -n 3 -- -p 5 -q 2
 
 To test the application, flows should be set up in the flow generator that match the values in the
 l3fwd_ipv4_route_array and/or l3fwd_ipv6_route_array table.
@@ -107,14 +107,14 @@ The default l3fwd_ipv4_route_array table is:
 .. code-block:: c
 
     struct l3fwd_ipv4_route l3fwd_ipv4_route_array[] = {
-        {IPv4(100, 10, 0, 0), 16, 0},
-        {IPv4(100, 20, 0, 0), 16, 1},
-        {IPv4(100, 30, 0, 0), 16, 2},
-        {IPv4(100, 40, 0, 0), 16, 3},
-        {IPv4(100, 50, 0, 0), 16, 4},
-        {IPv4(100, 60, 0, 0), 16, 5},
-        {IPv4(100, 70, 0, 0), 16, 6},
-        {IPv4(100, 80, 0, 0), 16, 7},
+        {RTE_IPV4(100, 10, 0, 0), 16, 0},
+        {RTE_IPV4(100, 20, 0, 0), 16, 1},
+        {RTE_IPV4(100, 30, 0, 0), 16, 2},
+        {RTE_IPV4(100, 40, 0, 0), 16, 3},
+        {RTE_IPV4(100, 50, 0, 0), 16, 4},
+        {RTE_IPV4(100, 60, 0, 0), 16, 5},
+        {RTE_IPV4(100, 70, 0, 0), 16, 6},
+        {RTE_IPV4(100, 80, 0, 0), 16, 7},
     };
 
 The default l3fwd_ipv6_route_array table is:
@@ -231,7 +231,8 @@ Debug logging and Statistics Collection
 ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
 
 The RTE_LIBRTE_IP_FRAG_TBL_STAT controls statistics collection for the IP Fragment Table.
-This macro is disabled by default.
+This macro is disabled by default, but it can be enabled by modifying the appropriate line
+in ``config/rte_config.h``.
 To make ip_reassembly print the statistics to the standard output,
 the user must send either an USR1, INT or TERM signal to the process.
 For all of these signals, the ip_reassembly process prints Fragment table statistics for each RX queue,