eal: add new prefetch write variants

[dpdk.git] / doc / guides / sample_app_ug / link_status_intr.rst

diff --git a/doc/guides/sample_app_ug/link_status_intr.rst b/doc/guides/sample_app_ug/link_status_intr.rst
index c7665fe..1057c75 100644 (file)
--- a/doc/guides/sample_app_ug/link_status_intr.rst
+++ b/doc/guides/sample_app_ug/link_status_intr.rst
@@ -49,7 +49,7 @@ where,
 
 *   -T PERIOD: statistics will be refreshed each PERIOD seconds (0 to disable, 10 default)
 
-To run the application in a linuxapp environment with 4 lcores, 4 memory channels, 16 ports and 8 RX queues per lcore,
+To run the application in a linux environment with 4 lcores, 4 memory channels, 16 ports and 8 RX queues per lcore,
 issue the command:
 
 .. code-block:: console
@@ -88,9 +88,6 @@ To fully understand this code, it is recommended to study the chapters that rela
 
 .. code-block:: c
 
-    if (rte_pci_probe() < 0)
-        rte_exit(EXIT_FAILURE, "Cannot probe PCI\n");
-
     /*
      * Each logical core is assigned a dedicated TX queue on each port.
      */
@@ -115,10 +112,6 @@ To fully understand this code, it is recommended to study the chapters that rela
         rte_eth_dev_info_get((uint8_t) portid, &dev_info);
     }
 
-Observe that:
-
-*   rte_pci_probe()  parses the devices on the PCI bus and initializes recognized devices.
-
 The next step is to configure the RX and TX queues.
 For each port, there is only one RX queue (only one lcore is able to poll a given port).
 The number of TX queues depends on the number of available lcores.
@@ -137,7 +130,6 @@ The global configuration is stored in a static structure:
     static const struct rte_eth_conf port_conf = {
         .rxmode = {
             .split_hdr_size = 0,
-            .offloads = DEV_RX_OFFLOAD_CRC_STRIP,
         },
         .txmode = {},
         .intr_conf = {
@@ -165,6 +157,8 @@ An example callback function that has been written as indicated below.
     lsi_event_callback(uint16_t port_id, enum rte_eth_event_type type, void *param)
     {
         struct rte_eth_link link;
+        int ret;
+        char link_status[RTE_ETH_LINK_MAX_STR_LEN];
 
         RTE_SET_USED(param);
 
@@ -172,13 +166,14 @@ An example callback function that has been written as indicated below.
 
         printf("Event type: %s\n", type == RTE_ETH_EVENT_INTR_LSC ? "LSC interrupt" : "unknown event");
 
-        rte_eth_link_get_nowait(port_id, &link);
-
-        if (link.link_status) {
-            printf("Port %d Link Up - speed %u Mbps - %s\n\n", port_id, (unsigned)link.link_speed,
-                  (link.link_duplex == ETH_LINK_FULL_DUPLEX) ? ("full-duplex") : ("half-duplex"));
-        } else
-            printf("Port %d Link Down\n\n", port_id);
+        ret = rte_eth_link_get_nowait(port_id, &link);
+        if (ret < 0) {
+            printf("Failed to get port %d link status: %s\n\n",
+                   port_id, rte_strerror(-ret));
+        } else {
+            rte_eth_link_to_str(link_status, sizeof(link_status), &link);
+            printf("Port %d %s\n", port_id, link_status);
+        }
     }
 
 This function is called when a link status interrupt is present for the right port.
@@ -312,11 +307,11 @@ The processing is very simple: processes the TX port from the RX port and then r
     static void
     lsi_simple_forward(struct rte_mbuf *m, unsigned portid)
     {
-        struct ether_hdr *eth;
+        struct rte_ether_hdr *eth;
         void *tmp;
         unsigned dst_port = lsi_dst_ports[portid];
 
-        eth = rte_pktmbuf_mtod(m, struct ether_hdr *);
+        eth = rte_pktmbuf_mtod(m, struct rte_ether_hdr *);
 
         /* 02:00:00:00:00:xx */
 
@@ -325,7 +320,7 @@ The processing is very simple: processes the TX port from the RX port and then r
         *((uint64_t *)tmp) = 0x000000000002 + (dst_port << 40);
 
         /* src addr */
-        ether_addr_copy(&lsi_ports_eth_addr[dst_port], &eth->s_addr);
+        rte_ether_addr_copy(&lsi_ports_eth_addr[dst_port], &eth->s_addr);
 
         lsi_send_packet(m, dst_port);
     }