eal: move common header files

[dpdk.git] / doc / guides / sample_app_ug / link_status_intr.rst

diff --git a/doc/guides/sample_app_ug/link_status_intr.rst b/doc/guides/sample_app_ug/link_status_intr.rst
index 8fa6d76..5283be8 100644 (file)
--- a/doc/guides/sample_app_ug/link_status_intr.rst
+++ b/doc/guides/sample_app_ug/link_status_intr.rst
@@ -49,7 +49,7 @@ where,
 
 *   -T PERIOD: statistics will be refreshed each PERIOD seconds (0 to disable, 10 default)
 
-To run the application in a linuxapp environment with 4 lcores, 4 memory channels, 16 ports and 8 RX queues per lcore,
+To run the application in a linux environment with 4 lcores, 4 memory channels, 16 ports and 8 RX queues per lcore,
 issue the command:
 
 .. code-block:: console
@@ -91,15 +91,11 @@ To fully understand this code, it is recommended to study the chapters that rela
     if (rte_pci_probe() < 0)
         rte_exit(EXIT_FAILURE, "Cannot probe PCI\n");
 
-    nb_ports = rte_eth_dev_count();
-    if (nb_ports == 0)
-        rte_exit(EXIT_FAILURE, "No Ethernet ports - bye\n");
-
     /*
      * Each logical core is assigned a dedicated TX queue on each port.
      */
 
-    for (portid = 0; portid < nb_ports; portid++) {
+    RTE_ETH_FOREACH_DEV(portid) {
         /* skip ports that are not enabled */
 
         if ((lsi_enabled_port_mask & (1 << portid)) == 0)
@@ -141,10 +137,6 @@ The global configuration is stored in a static structure:
     static const struct rte_eth_conf port_conf = {
         .rxmode = {
             .split_hdr_size = 0,
-            .header_split = 0,   /**< Header Split disabled */
-            .hw_ip_checksum = 0, /**< IP checksum offload disabled */
-            .hw_vlan_filter = 0, /**< VLAN filtering disabled */
-            .hw_strip_crc= 0,    /**< CRC stripped by hardware */
         },
         .txmode = {},
         .intr_conf = {
@@ -172,6 +164,7 @@ An example callback function that has been written as indicated below.
     lsi_event_callback(uint16_t port_id, enum rte_eth_event_type type, void *param)
     {
         struct rte_eth_link link;
+        int ret;
 
         RTE_SET_USED(param);
 
@@ -179,9 +172,11 @@ An example callback function that has been written as indicated below.
 
         printf("Event type: %s\n", type == RTE_ETH_EVENT_INTR_LSC ? "LSC interrupt" : "unknown event");
 
-        rte_eth_link_get_nowait(port_id, &link);
-
-        if (link.link_status) {
+        ret = rte_eth_link_get_nowait(port_id, &link);
+        if (ret < 0) {
+            printf("Failed to get port %d link status: %s\n\n",
+                   port_id, rte_strerror(-ret));
+        } else if (link.link_status) {
             printf("Port %d Link Up - speed %u Mbps - %s\n\n", port_id, (unsigned)link.link_speed,
                   (link.link_duplex == ETH_LINK_FULL_DUPLEX) ? ("full-duplex") : ("half-duplex"));
         } else
@@ -319,11 +314,11 @@ The processing is very simple: processes the TX port from the RX port and then r
     static void
     lsi_simple_forward(struct rte_mbuf *m, unsigned portid)
     {
-        struct ether_hdr *eth;
+        struct rte_ether_hdr *eth;
         void *tmp;
         unsigned dst_port = lsi_dst_ports[portid];
 
-        eth = rte_pktmbuf_mtod(m, struct ether_hdr *);
+        eth = rte_pktmbuf_mtod(m, struct rte_ether_hdr *);
 
         /* 02:00:00:00:00:xx */
 
@@ -332,7 +327,7 @@ The processing is very simple: processes the TX port from the RX port and then r
         *((uint64_t *)tmp) = 0x000000000002 + (dst_port << 40);
 
         /* src addr */
-        ether_addr_copy(&lsi_ports_eth_addr[dst_port], &eth->s_addr);
+        rte_ether_addr_copy(&lsi_ports_eth_addr[dst_port], &eth->s_addr);
 
         lsi_send_packet(m, dst_port);
     }