app/testpmd: introduce QinQ offload option

[dpdk.git] / doc / guides / testpmd_app_ug / run_app.rst

diff --git a/doc/guides/testpmd_app_ug/run_app.rst b/doc/guides/testpmd_app_ug/run_app.rst
index 89a097d..9723cf5 100644 (file)
--- a/doc/guides/testpmd_app_ug/run_app.rst
+++ b/doc/guides/testpmd_app_ug/run_app.rst
@@ -121,12 +121,24 @@ The command line options are:
        XX:XX:XX:XX:XX:02
        ...
 
-
 *   ``--eth-peer=N,XX:XX:XX:XX:XX:XX``
 
     Set the MAC address ``XX:XX:XX:XX:XX:XX`` of the peer port N,
     where 0 <= N < ``CONFIG_RTE_MAX_ETHPORTS`` from the configuration file.
 
+*   ``--tx-ip=SRC,DST``
+
+    Set the source and destination IP address used when doing transmit only test.
+    The defaults address values are source 192.18.0.1 and
+    destination 192.18.0.2. These are special purpose addresses
+    reserved for benchmarking (RFC 2544).
+
+*   ``--tx-udp=SRC[,DST]``
+
+    Set the source and destination UDP port number for transmit test only test.
+    The default port is the port 9 which is defined for the discard protocol
+    (RFC 863).
+
 *   ``--pkt-filter-mode=mode``
 
     Set Flow Director mode where mode is either ``none`` (the default), ``signature`` or ``perfect``.
@@ -186,6 +198,10 @@ The command line options are:
 
     Enable hardware VLAN extend.
 
+*   ``--enable-hw-qinq-strip``
+
+    Enable hardware QINQ strip.
+
 *   ``--enable-drop-en``
 
     Enable per-queue packet drop for packets with no descriptors.
@@ -332,6 +348,12 @@ The command line options are:
 
     Disable check on link status when starting/stopping ports.
 
+*   ``--disable-device-start``
+
+    Do not automatically start all ports. This allows testing
+    configuration of rx and tx queues before device is started
+    for the first time.
+
 *   ``--no-lsc-interrupt``
 
     Disable LSC interrupts for all ports, even those supporting it.
@@ -369,7 +391,7 @@ The command line options are:
 
 *   ``--hot-plug``
 
-    Enable device event monitor mechanism for hot plug.
+    Enable device event monitor mechanism for hotplug.
 
 *   ``--vxlan-gpe-port=N``
 
@@ -409,23 +431,23 @@ The command line options are:
 
 *   ``--noisy-lkup-memory=N``
 
-    Set the size of the noisy neighbour simulation memory buffer in MB to N.
+    Set the size of the noisy neighbor simulation memory buffer in MB to N.
     Only available with the noisy forwarding mode. The default value is 0.
 
 
 *   ``--noisy-lkup-num-reads=N``
 
-    Set the number of reads to be done in noisy neighbour simulation memory buffer to N.
+    Set the number of reads to be done in noisy neighbor simulation memory buffer to N.
     Only available with the noisy forwarding mode. The default value is 0.
 
 *   ``--noisy-lkup-num-writes=N``
 
-    Set the number of writes to be done in noisy neighbour simulation memory buffer to N.
+    Set the number of writes to be done in noisy neighbor simulation memory buffer to N.
     Only available with the noisy forwarding mode. The default value is 0.
 
 *   ``--noisy-lkup-num-reads-writes=N``
 
-    Set the number of r/w accesses to be done in noisy neighbour simulation memory buffer to N.
+    Set the number of r/w accesses to be done in noisy neighbor simulation memory buffer to N.
     Only available with the noisy forwarding mode. The default value is 0.
 
 *   ``--no-iova-contig``