app/testpmd: use consistent vdev names

[dpdk.git] / doc / guides / testpmd_app_ug / testpmd_funcs.rst

diff --git a/doc/guides/testpmd_app_ug/testpmd_funcs.rst b/doc/guides/testpmd_app_ug/testpmd_funcs.rst
index d812989..5caca30 100644 (file)
--- a/doc/guides/testpmd_app_ug/testpmd_funcs.rst
+++ b/doc/guides/testpmd_app_ug/testpmd_funcs.rst
@@ -98,9 +98,11 @@ Start packet forwarding with current configuration::
 start tx_first
 ~~~~~~~~~~~~~~
 
-Start packet forwarding with current configuration after sending one burst of packets::
+Start packet forwarding with current configuration after sending specified number of bursts of packets::
 
-   testpmd> start tx_first
+   testpmd> start tx_first (""|burst_num)
+
+The default burst number is 1 when ``burst_num`` not presented.
 
 stop
 ~~~~
@@ -177,6 +179,10 @@ For example:
      ipv6-sctp
      ipv6-other
      l2_payload
+     port
+     vxlan
+     geneve
+     nvgre
 
 show port rss reta
 ~~~~~~~~~~~~~~~~~~
@@ -993,7 +999,7 @@ For example, to move a pci device using ixgbe under DPDK management:
 .. code-block:: console
 
    # Check the status of the available devices.
-   ./tools/dpdk_nic_bind.py --status
+   ./tools/dpdk-devbind.py --status
 
    Network devices using DPDK-compatible driver
    ============================================
@@ -1005,11 +1011,11 @@ For example, to move a pci device using ixgbe under DPDK management:
 
 
    # Bind the device to igb_uio.
-   sudo ./tools/dpdk_nic_bind.py -b igb_uio 0000:0a:00.0
+   sudo ./tools/dpdk-devbind.py -b igb_uio 0000:0a:00.0
 
 
    # Recheck the status of the devices.
-   ./tools/dpdk_nic_bind.py --status
+   ./tools/dpdk-devbind.py --status
    Network devices using DPDK-compatible driver
    ============================================
    0000:0a:00.0 '82599ES 10-Gigabit' drv=igb_uio unused=
@@ -1035,14 +1041,14 @@ For example, to attach a port created by pcap PMD.
 
 .. code-block:: console
 
-   testpmd> port attach eth_pcap0
+   testpmd> port attach net_pcap0
    Attaching a new port...
-   PMD: Initializing pmd_pcap for eth_pcap0
+   PMD: Initializing pmd_pcap for net_pcap0
    PMD: Creating pcap-backed ethdev on numa socket 0
    Port 0 is attached. Now total ports is 1
    Done
 
-In this case, identifier is ``eth_pcap0``.
+In this case, identifier is ``net_pcap0``.
 This identifier format is the same as ``--vdev`` format of DPDK applications.
 
 For example, to re-attach a bonded port which has been previously detached,
@@ -1050,10 +1056,10 @@ the mode and slave parameters must be given.
 
 .. code-block:: console
 
-   testpmd> port attach eth_bond_0,mode=0,slave=1
+   testpmd> port attach net_bond_0,mode=0,slave=1
    Attaching a new port...
-   EAL: Initializing pmd_bond for eth_bond_0
-   EAL: Create bonded device eth_bond_0 on port 0 in mode 0 on socket 0.
+   EAL: Initializing pmd_bond for net_bond_0
+   EAL: Create bonded device net_bond_0 on port 0 in mode 0 on socket 0.
    Port 0 is attached. Now total ports is 1
    Done
 
@@ -1101,7 +1107,7 @@ For example, to detach a virtual device port 0.
    testpmd> port detach 0
    Detaching a port...
    PMD: Closing pcap ethdev on numa socket 0
-   Port 'eth_pcap0' is detached. Now total ports is 0
+   Port 'net_pcap0' is detached. Now total ports is 0
    Done
 
 To remove a pci device completely from the system, first detach the port from testpmd.
@@ -1112,9 +1118,9 @@ For example, to move a pci device under kernel management:
 
 .. code-block:: console
 
-   sudo ./tools/dpdk_nic_bind.py -b ixgbe 0000:0a:00.0
+   sudo ./tools/dpdk-devbind.py -b ixgbe 0000:0a:00.0
 
-   ./tools/dpdk_nic_bind.py --status
+   ./tools/dpdk-devbind.py --status
 
    Network devices using DPDK-compatible driver
    ============================================
@@ -1284,7 +1290,7 @@ port config - RSS
 
 Set the RSS (Receive Side Scaling) mode on or off::
 
-   testpmd> port config all rss (all|ip|tcp|udp|sctp|ether|none)
+   testpmd> port config all rss (all|ip|tcp|udp|sctp|ether|port|vxlan|geneve|nvgre|none)
 
 RSS is on by default.