app/testpmd: parse flow command line for ESP

[dpdk.git] / doc / guides / testpmd_app_ug / testpmd_funcs.rst

diff --git a/doc/guides/testpmd_app_ug/testpmd_funcs.rst b/doc/guides/testpmd_app_ug/testpmd_funcs.rst
index 504dbbe..7f4564c 100644 (file)
--- a/doc/guides/testpmd_app_ug/testpmd_funcs.rst
+++ b/doc/guides/testpmd_app_ug/testpmd_funcs.rst
@@ -33,7 +33,7 @@ If you type a partial command and hit ``<TAB>`` you get a list of the available
 
 .. note::
 
-   Some examples in this document are too long to fit on one line are are shown wrapped at `"\\"` for display purposes::
+   Some examples in this document are too long to fit on one line are shown wrapped at `"\\"` for display purposes::
 
       testpmd> set flow_ctrl rx (on|off) tx (on|off) (high_water) (low_water) \
                (pause_time) (send_xon) (port_id)
@@ -480,6 +480,28 @@ Show ptypes supported for a specific port::
 
    testpmd> show port (port_id) ptypes
 
+set port supported ptypes
+~~~~~~~~~~~~~~~~~~~~~~~~~
+
+set packet types classification for a specific port::
+
+   testpmd> set port (port_id) ptypes_mask (mask)
+
+show port mac addresses info
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+Show mac addresses added for a specific port::
+
+   testpmd> show port (port_id) macs
+
+
+show port multicast mac addresses info
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+Show multicast mac addresses added for a specific port::
+
+   testpmd> show port (port_id) mcast_macs
+
 show device info
 ~~~~~~~~~~~~~~~~
 
@@ -1711,8 +1733,7 @@ Enable or disable a per port Tx offloading on all Tx queues of a port::
                   sctp_cksum, tcp_tso, udp_tso, outer_ipv4_cksum,
                   qinq_insert, vxlan_tnl_tso, gre_tnl_tso,
                   ipip_tnl_tso, geneve_tnl_tso, macsec_insert,
-                  mt_lockfree, multi_segs, mbuf_fast_free, security,
-                  match_metadata
+                  mt_lockfree, multi_segs, mbuf_fast_free, security
 
 This command should be run when the port is stopped, or else it will fail.
 
@@ -2147,6 +2168,15 @@ Set the maximum packet length::
 
 This is equivalent to the ``--max-pkt-len`` command-line option.
 
+port config - max-lro-pkt-size
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+Set the maximum LRO aggregated packet size::
+
+   testpmd> port config all max-lro-pkt-size (value)
+
+This is equivalent to the ``--max-lro-pkt-size`` command-line option.
+
 port config - Drop Packets
 ~~~~~~~~~~~~~~~~~~~~~~~~~~
 
@@ -2744,7 +2774,7 @@ Traffic Management
 ------------------
 
 The following section shows functions for configuring traffic management on
-on the ethernet device through the use of generic TM API.
+the ethernet device through the use of generic TM API.
 
 show port traffic management capability
 ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
@@ -3939,6 +3969,10 @@ This section lists supported pattern items and their attributes, if any.
 
   - ``proto_id {unsigned}``: PPP protocol identifier.
 
+- ``l2tpv3oip``: match L2TPv3 over IP header.
+
+  - ``session_id {unsigned}``: L2TPv3 over IP session identifier.
+
 Actions list
 ^^^^^^^^^^^^
 
@@ -4198,6 +4232,14 @@ This section lists supported actions and their attributes, if any.
 
   - ``value {unsigned}``: Value to decrease TCP acknowledgment number by.
 
+- ``set_ipv4_dscp``: Set IPv4 DSCP value with specified value
+
+  - ``dscp_value {unsigned}``: The new DSCP value to be set
+
+- ``set_ipv6_dscp``: Set IPv6 DSCP value with specified value
+
+  - ``dscp_value {unsigned}``: The new DSCP value to be set
+
 Destroying flow rules
 ~~~~~~~~~~~~~~~~~~~~~
 
@@ -4736,6 +4778,20 @@ Decapsulating VxLAN::
  testpmd> flow create 0 ingress pattern eth / ipv4 / udp / vxlan / eth / ipv4 /
         end actions raw_decap / queue index 0 / end
 
+Sample ESP rules
+~~~~~~~~~~~~~~~~
+
+ESP rules can be created by the following commands::
+
+ testpmd> flow create 0 ingress pattern eth / ipv4 / esp spi is 1 / end actions
+        queue index 3 / end
+ testpmd> flow create 0 ingress pattern eth / ipv4 / udp / esp spi is 1 / end
+        actions queue index 3 / end
+ testpmd> flow create 0 ingress pattern eth / ipv6 / esp spi is 1 / end actions
+        queue index 3 / end
+ testpmd> flow create 0 ingress pattern eth / ipv6 / udp / esp spi is 1 / end
+        actions queue index 3 / end
+
 BPF Functions
 --------------