********************* Infos for port 0 *********************
MAC address: XX:XX:XX:XX:XX:XX
+ Connect to socket: 0
+ memory allocation on the socket: 0
Link status: up
- Link speed: 10000 Mbps
+ Link speed: 40000 Mbps
Link duplex: full-duplex
Promiscuous mode: enabled
Allmulticast mode: disabled
- Maximum number of MAC addresses: 127
+ Maximum number of MAC addresses: 64
+ Maximum number of MAC addresses of hash filtering: 0
VLAN offload:
strip on
filter on
qinq(extend) off
+ Redirection table size: 512
+ Supported flow types:
+ ipv4-frag
+ ipv4-tcp
+ ipv4-udp
+ ipv4-sctp
+ ipv4-other
+ ipv6-frag
+ ipv6-tcp
+ ipv6-udp
+ ipv6-sctp
+ ipv6-other
+ l2_payload
show port rss reta
~~~~~~~~~~~~~~~~~~
tx_vlan reset (port_id)
-tx_checksum set
-~~~~~~~~~~~~~~~
+csum set
+~~~~~~~~
Select hardware or software calculation of the checksum when
transmitting a packet using the csum forward engine:
-tx_cksum set (ip|udp|tcp|sctp|vxlan)
+csum set (ip|udp|tcp|sctp|outer-ip) (hw|sw) (port_id)
-ip|udp|tcp|sctp always concern the inner layer.
-vxlan concerns the outer IP and UDP layer (in case the packet
-is recognized as a vxlan packet by the forward engine)
+- ip|udp|tcp|sctp always concern the inner layer.
+
+- outer-ip concerns the outer IP layer in case the packet is recognized
+ as a tunnel packet by the forward engine (vxlan, gre and ipip are
+ supported). See "csum parse-tunnel" command.
.. note::
Check the NIC Datasheet for hardware limits.
-tx_checksum show
-~~~~~~~~~~~~~~~~
+csum parse-tunnel
+~~~~~~~~~~~~~~~~~
+
+Define how tunneled packets should be handled by the csum forward
+engine.
+
+csum parse-tunnel (on|off) (tx_port_id)
+
+If enabled, the csum forward engine will try to recognize supported
+tunnel headers (vxlan, gre, ipip).
+
+If disabled, treat tunnel packets as non-tunneled packets (a inner
+header is handled as a packet payload).
+
+.. note::
+
+ The port argument is the TX port like in the "csum set" command.
+
+Example:
+
+Consider a packet as following:
+"eth_out/ipv4_out/udp_out/vxlan/eth_in/ipv4_in/tcp_in"
+
+- If parse-tunnel is enabled, the ip|udp|tcp|sctp parameters of "csum
+ set" command are about inner headers (here ipv4_in and tcp_in), and the
+ outer-ip parameter is about outer headers (here ipv4_out).
+
+- If parse-tunnel is disabled, the ip|udp|tcp|sctp parameters of "csum
+ set" command are about outer headers, here ipv4_out and udp_out.
+
+csum show
+~~~~~~~~~
Display tx checksum offload configuration:
-tx_checksum show (port_id)
+csum show (port_id)
tso set
~~~~~~~
tso set (segsize) (port_id)
.. note::
- Please check the NIC datasheet for HW limits
+
+ Check the NIC datasheet for hardware limits
tso show
~~~~~~~~
Set the RSS (Receive Side Scaling) mode on or off:
-port config all rss (ip|udp|none)
+port config all rss (all|ip|tcp|udp|sctp|ether|none)
RSS is on by default.
flow_director_flex_payload (port_id) (raw|l2|l3|l4) (config)
-For example, to select the first 16 bytes from the offset 4 (bytes) of packet’s payload as flexible payload.
+For example, to select the first 16 bytes from the offset 4 (bytes) of packet's payload as flexible payload.
.. code-block:: console
testpmd> flow_director_flex_payload 0 l4 (4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19)
+
+get_sym_hash_ena_per_port
+~~~~~~~~~~~~~~~~~~~~~~~~~
+
+Get symmetric hash enable configuration per port.
+
+get_sym_hash_ena_per_port (port_id)
+
+For example, to get symmetric hash enable configuration of port 1.
+
+.. code-block:: console
+
+ testpmd> get_sym_hash_ena_per_port 1
+
+set_sym_hash_ena_per_port
+~~~~~~~~~~~~~~~~~~~~~~~~~
+
+Set symmetric hash enable configuration per port to enable or disable.
+
+set_sym_hash_ena_per_port (port_id) (enable|disable)
+
+For example, to set symmetric hash enable configuration of port 1 to enable.
+
+.. code-block:: console
+
+ testpmd> set_sym_hash_ena_per_port 1 enable
+
+get_hash_global_config
+~~~~~~~~~~~~~~~~~~~~~~
+
+Get the global configurations of hash filters.
+
+get_hash_global_config (port_id)
+
+For example, to get the global configurations of hash filters of port 1.
+
+.. code-block:: console
+
+ testpmd> get_hash_global_config 1
+
+set_hash_global_config
+~~~~~~~~~~~~~~~~~~~~~~
+
+Set the global configurations of hash filters.
+
+set_hash_global_config (port_id) (toeplitz|simple_xor|default)
+(ipv4|ipv4-frag|ipv4-tcp|ipv4-udp|ipv4-sctp|ipv4-other|ipv6|ipv6-frag|ipv6-tcp|ipv6-udp|ipv6-sctp|ipv6-other|l2_payload)
+(enable|disable)
+
+For example, to enable simple_xor for flow type of ipv6 on port 2.
+
+.. code-block:: console
+
+ testpmd> set_hash_global_config 2 simple_xor ipv6 enable