-.. BSD LICENSE
- Copyright(c) 2010-2014 Intel Corporation. All rights reserved.
- All rights reserved.
-
- Redistribution and use in source and binary forms, with or without
- modification, are permitted provided that the following conditions
- are met:
-
- * Redistributions of source code must retain the above copyright
- notice, this list of conditions and the following disclaimer.
- * Redistributions in binary form must reproduce the above copyright
- notice, this list of conditions and the following disclaimer in
- the documentation and/or other materials provided with the
- distribution.
- * Neither the name of Intel Corporation nor the names of its
- contributors may be used to endorse or promote products derived
- from this software without specific prior written permission.
-
- THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
- "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
- LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
- A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
- OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
- SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
- LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
- DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
- THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
- (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
- OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+.. SPDX-License-Identifier: BSD-3-Clause
+ Copyright(c) 2010-2016 Intel Corporation.
+
+.. _testpmd_runtime:
Testpmd Runtime Functions
=========================
-Where the testpmd application is started in interactive mode, (-i|--interactive),
+Where the testpmd application is started in interactive mode, (``-i|--interactive``),
it displays a prompt that can be used to start and stop forwarding,
-configure the application, display statistics, set the Flow Director and other tasks.
-
-.. code-block:: console
+configure the application, display statistics (including the extended NIC
+statistics aka xstats) , set the Flow Director and other tasks::
- testpmd>
+ testpmd>
The testpmd prompt has some, limited, readline support.
-Common bash command- line functions such as Ctrl+a and Ctrl+e to go to the start and end of the prompt line are supported
+Common bash command-line functions such as ``Ctrl+a`` and ``Ctrl+e`` to go to the start and end of the prompt line are supported
as well as access to the command history via the up-arrow.
There is also support for tab completion.
-If you type a partial command and hit <TAB> you get a list of the available completions:
+If you type a partial command and hit ``<TAB>`` you get a list of the available completions:
.. code-block:: console
- testpmd> show port <TAB>
+ testpmd> show port <TAB>
+
+ info [Mul-choice STRING]: show|clear port info|stats|xstats|fdir|stat_qmap|dcb_tc|cap X
+ info [Mul-choice STRING]: show|clear port info|stats|xstats|fdir|stat_qmap|dcb_tc|cap all
+ stats [Mul-choice STRING]: show|clear port info|stats|xstats|fdir|stat_qmap|dcb_tc|cap X
+ stats [Mul-choice STRING]: show|clear port info|stats|xstats|fdir|stat_qmap|dcb_tc|cap all
+ ...
+
+
+.. note::
+
+ Some examples in this document are too long to fit on one line are shown wrapped at `"\\"` for display purposes::
- info [Mul-choice STRING]: show|clear port info|stats|fdir|stat_qmap X
- info [Mul-choice STRING]: show|clear port info|stats|fdir|stat_qmap all
- stats [Mul-choice STRING]: show|clear port info|stats|fdir|stat_qmap X
- stats [Mul-choice STRING]: show|clear port info|stats|fdir|stat_qmap all
- ...
+ testpmd> set flow_ctrl rx (on|off) tx (on|off) (high_water) (low_water) \
+ (pause_time) (send_xon) (port_id)
+
+In the real ``testpmd>`` prompt these commands should be on a single line.
Help Functions
--------------
.. code-block:: console
- testpmd> help
+ testpmd> help
+
+ help control : Start and stop forwarding.
+ help display : Displaying port, stats and config information.
+ help config : Configuration information.
+ help ports : Configuring ports.
+ help registers : Reading and setting port registers.
+ help filters : Filters configuration help.
+ help all : All of the above sections.
+
+
+Command File Functions
+----------------------
+
+To facilitate loading large number of commands or to avoid cutting and pasting where not
+practical or possible testpmd supports alternative methods for executing commands.
+
+* If started with the ``--cmdline-file=FILENAME`` command line argument testpmd
+ will execute all CLI commands contained within the file immediately before
+ starting packet forwarding or entering interactive mode.
+
+.. code-block:: console
+
+ ./testpmd -n4 -r2 ... -- -i --cmdline-file=/home/ubuntu/flow-create-commands.txt
+ Interactive-mode selected
+ CLI commands to be read from /home/ubuntu/flow-create-commands.txt
+ Configuring Port 0 (socket 0)
+ Port 0: 7C:FE:90:CB:74:CE
+ Configuring Port 1 (socket 0)
+ Port 1: 7C:FE:90:CB:74:CA
+ Checking link statuses...
+ Port 0 Link Up - speed 10000 Mbps - full-duplex
+ Port 1 Link Up - speed 10000 Mbps - full-duplex
+ Done
+ Flow rule #0 created
+ Flow rule #1 created
+ ...
+ ...
+ Flow rule #498 created
+ Flow rule #499 created
+ Read all CLI commands from /home/ubuntu/flow-create-commands.txt
+ testpmd>
+
+
+* At run-time additional commands can be loaded in bulk by invoking the ``load FILENAME``
+ command.
+
+.. code-block:: console
+
+ testpmd> load /home/ubuntu/flow-create-commands.txt
+ Flow rule #0 created
+ Flow rule #1 created
+ ...
+ ...
+ Flow rule #498 created
+ Flow rule #499 created
+ Read all CLI commands from /home/ubuntu/flow-create-commands.txt
+ testpmd>
+
+
+In all cases output from any included command will be displayed as standard output.
+Execution will continue until the end of the file is reached regardless of
+whether any errors occur. The end user must examine the output to determine if
+any failures occurred.
- Help is available for the following sections:
- help control : Start and stop forwarding.
- help display : Displaying port, stats and config information.
- help config : Configuration information.
- help ports : Configuring ports.
- help flowdir : Flow Director filter help.
- help registers : Reading and setting port registers.
- help filters : Filters configuration help.
- help all : All of the above sections.
Control Functions
-----------------
start
~~~~~
-Start packet forwarding with current configuration:
+Start packet forwarding with current configuration::
-start
+ testpmd> start
start tx_first
~~~~~~~~~~~~~~
-Start packet forwarding with current configuration after sending one burst of packets:
+Start packet forwarding with current configuration after sending specified number of bursts of packets::
-start tx_first
+ testpmd> start tx_first (""|burst_num)
+
+The default burst number is 1 when ``burst_num`` not presented.
stop
~~~~
-Stop packet forwarding, and display accumulated statistics:
+Stop packet forwarding, and display accumulated statistics::
-stop
+ testpmd> stop
quit
~~~~
-Quit to prompt:
+Quit to prompt::
+
+ testpmd> quit
-quit
Display Functions
-----------------
show port
~~~~~~~~~
-Display information for a given port or all ports:
+Display information for a given port or all ports::
-show port (info|stats|fdir|stat_qmap) (port_id|all)
+ testpmd> show port (info|summary|stats|xstats|fdir|stat_qmap|dcb_tc|cap) (port_id|all)
The available information categories are:
-info : General port information such as MAC address.
+* ``info``: General port information such as MAC address.
-stats : RX/TX statistics.
+* ``summary``: Brief port summary such as Device Name, Driver Name etc.
-fdir : Flow Director information and statistics.
+* ``stats``: RX/TX statistics.
-stat_qmap : Queue statistics mapping.
+* ``xstats``: RX/TX extended NIC statistics.
-For example:
+* ``fdir``: Flow Director information and statistics.
-.. code-block:: console
+* ``stat_qmap``: Queue statistics mapping.
+
+* ``dcb_tc``: DCB information such as TC mapping.
- testpmd> show port info 0
+* ``cap``: Supported offload capabilities.
- ********************* Infos for port 0 *********************
+For example:
+
+.. code-block:: console
- MAC address: XX:XX:XX:XX:XX:XX
- Link status: up
- Link speed: 10000 Mbps
- Link duplex: full-duplex
- Promiscuous mode: enabled
- Allmulticast mode: disabled
- Maximum number of MAC addresses: 127
- VLAN offload:
- strip on
- filter on
- qinq(extend) off
+ testpmd> show port info 0
+
+ ********************* Infos for port 0 *********************
+
+ MAC address: XX:XX:XX:XX:XX:XX
+ Connect to socket: 0
+ memory allocation on the socket: 0
+ Link status: up
+ Link speed: 40000 Mbps
+ Link duplex: full-duplex
+ Promiscuous mode: enabled
+ Allmulticast mode: disabled
+ Maximum number of MAC addresses: 64
+ Maximum number of MAC addresses of hash filtering: 0
+ VLAN offload:
+ strip on, filter on, extend off, qinq strip off
+ Redirection table size: 512
+ Supported flow types:
+ ipv4-frag
+ ipv4-tcp
+ ipv4-udp
+ ipv4-sctp
+ ipv4-other
+ ipv6-frag
+ ipv6-tcp
+ ipv6-udp
+ ipv6-sctp
+ ipv6-other
+ l2_payload
+ port
+ vxlan
+ geneve
+ nvgre
+ vxlan-gpe
show port rss reta
~~~~~~~~~~~~~~~~~~
-Display the rss redirection table entry indicated by masks on port X:
+Display the rss redirection table entry indicated by masks on port X::
-show port (port_id) rss reta (size) (mask0, mask1...)
+ testpmd> show port (port_id) rss reta (size) (mask0, mask1...)
size is used to indicate the hardware supported reta size
show port rss-hash
~~~~~~~~~~~~~~~~~~
-Display the RSS hash functions and RSS hash key of a port:
+Display the RSS hash functions and RSS hash key of a port::
-show port (port_id) rss-hash [key]
+ testpmd> show port (port_id) rss-hash [key]
clear port
~~~~~~~~~~
-Clear the port statistics for a given port or for all ports:
+Clear the port statistics for a given port or for all ports::
-clear port (info|stats|fdir|stat_qmap) (port_id|all)
+ testpmd> clear port (info|stats|xstats|fdir|stat_qmap) (port_id|all)
-For example:
+For example::
-.. code-block:: console
+ testpmd> clear port stats all
+
+show (rxq|txq)
+~~~~~~~~~~~~~~
+
+Display information for a given port's RX/TX queue::
+
+ testpmd> show (rxq|txq) info (port_id) (queue_id)
+
+show desc status(rxq|txq)
+~~~~~~~~~~~~~~~~~~~~~~~~~
+
+Display information for a given port's RX/TX descriptor status::
+
+ testpmd> show port (port_id) (rxq|txq) (queue_id) desc (desc_id) status
- testpmd> clear port stats all
show config
~~~~~~~~~~~
Displays the configuration of the application.
-The configuration comes from the command-line, the runtime or the application defaults:
+The configuration comes from the command-line, the runtime or the application defaults::
-show config (rxtx|cores|fwd)
+ testpmd> show config (rxtx|cores|fwd|txpkts)
The available information categories are:
-rxtx : RX/TX configuration items.
+* ``rxtx``: RX/TX configuration items.
+
+* ``cores``: List of forwarding cores.
-cores : List of forwarding cores.
+* ``fwd``: Packet forwarding configuration.
-fwd : Packet forwarding configuration.
+* ``txpkts``: Packets to TX configuration.
For example:
.. code-block:: console
- testpmd> show config rxtx
+ testpmd> show config rxtx
- io packet forwarding - CRC stripping disabled - packets/burst=16
- nb forwarding cores=2 - nb forwarding ports=1
- RX queues=1 - RX desc=128 - RX free threshold=0
- RX threshold registers: pthresh=8 hthresh=8 wthresh=4
- TX queues=1 - TX desc=512 - TX free threshold=0
- TX threshold registers: pthresh=36 hthresh=0 wthresh=0
- TX RS bit threshold=0 - TXQ flags=0x0
+ io packet forwarding - CRC stripping disabled - packets/burst=16
+ nb forwarding cores=2 - nb forwarding ports=1
+ RX queues=1 - RX desc=128 - RX free threshold=0
+ RX threshold registers: pthresh=8 hthresh=8 wthresh=4
+ TX queues=1 - TX desc=512 - TX free threshold=0
+ TX threshold registers: pthresh=36 hthresh=0 wthresh=0
+ TX RS bit threshold=0 - TXQ flags=0x0
-read rxd
+set fwd
+~~~~~~~
+
+Set the packet forwarding mode::
+
+ testpmd> set fwd (io|mac|macswap|flowgen| \
+ rxonly|txonly|csum|icmpecho|noisy) (""|retry)
+
+``retry`` can be specified for forwarding engines except ``rx_only``.
+
+The available information categories are:
+
+* ``io``: Forwards packets "as-is" in I/O mode.
+ This is the fastest possible forwarding operation as it does not access packets data.
+ This is the default mode.
+
+* ``mac``: Changes the source and the destination Ethernet addresses of packets before forwarding them.
+ Default application behavior is to set source Ethernet address to that of the transmitting interface, and destination
+ address to a dummy value (set during init). The user may specify a target destination Ethernet address via the 'eth-peer' or
+ 'eth-peers-configfile' command-line options. It is not currently possible to specify a specific source Ethernet address.
+
+* ``macswap``: MAC swap forwarding mode.
+ Swaps the source and the destination Ethernet addresses of packets before forwarding them.
+
+* ``flowgen``: Multi-flow generation mode.
+ Originates a number of flows (with varying destination IP addresses), and terminate receive traffic.
+
+* ``rxonly``: Receives packets but doesn't transmit them.
+
+* ``txonly``: Generates and transmits packets without receiving any.
+
+* ``csum``: Changes the checksum field with hardware or software methods depending on the offload flags on the packet.
+
+* ``icmpecho``: Receives a burst of packets, lookup for ICMP echo requests and, if any, send back ICMP echo replies.
+
+* ``ieee1588``: Demonstrate L2 IEEE1588 V2 PTP timestamping for RX and TX. Requires ``CONFIG_RTE_LIBRTE_IEEE1588=y``.
+
+* ``softnic``: Demonstrates the softnic forwarding operation. In this mode, packet forwarding is
+ similar to I/O mode except for the fact that packets are loopback to the softnic ports only. Therefore, portmask parameter should be set to softnic port only. The various software based custom NIC pipelines specified through the softnic firmware (DPDK packet framework script) can be tested in this mode. Furthermore, it allows to build 5-level hierarchical QoS scheduler as a default option that can be enabled through CLI once testpmd application is initialised. The user can modify the default scheduler hierarchy or can specify the new QoS Scheduler hierarchy through CLI. Requires ``CONFIG_RTE_LIBRTE_PMD_SOFTNIC=y``.
+
+* ``noisy``: Noisy neighbor simulation.
+ Simulate more realistic behavior of a guest machine engaged in receiving
+ and sending packets performing Virtual Network Function (VNF).
+
+Example::
+
+ testpmd> set fwd rxonly
+
+ Set rxonly packet forwarding mode
+
+
+show fwd
~~~~~~~~
-Display an RX descriptor for a port RX queue:
+When running, forwarding engines maintain statistics from the time they have been started.
+Example for the io forwarding engine, with some packet drops on the tx side::
-read rxd (port_id) (queue_id) (rxd_id)
+ testpmd> show fwd stats all
-For example:
+ ------- Forward Stats for RX Port= 0/Queue= 0 -> TX Port= 1/Queue= 0 -------
+ RX-packets: 274293770 TX-packets: 274293642 TX-dropped: 128
-.. code-block:: console
+ ------- Forward Stats for RX Port= 1/Queue= 0 -> TX Port= 0/Queue= 0 -------
+ RX-packets: 274301850 TX-packets: 274301850 TX-dropped: 0
+
+ ---------------------- Forward statistics for port 0 ----------------------
+ RX-packets: 274293802 RX-dropped: 0 RX-total: 274293802
+ TX-packets: 274301862 TX-dropped: 0 TX-total: 274301862
+ ----------------------------------------------------------------------------
+
+ ---------------------- Forward statistics for port 1 ----------------------
+ RX-packets: 274301894 RX-dropped: 0 RX-total: 274301894
+ TX-packets: 274293706 TX-dropped: 128 TX-total: 274293834
+ ----------------------------------------------------------------------------
+
+ +++++++++++++++ Accumulated forward statistics for all ports+++++++++++++++
+ RX-packets: 548595696 RX-dropped: 0 RX-total: 548595696
+ TX-packets: 548595568 TX-dropped: 128 TX-total: 548595696
+ ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
+
+clear fwd
+~~~~~~~~~
+
+Clear the forwarding engines statistics::
+
+ testpmd> clear fwd stats all
+
+read rxd
+~~~~~~~~
+
+Display an RX descriptor for a port RX queue::
+
+ testpmd> read rxd (port_id) (queue_id) (rxd_id)
- testpmd> read rxd 0 0 4
+For example::
+
+ testpmd> read rxd 0 0 4
0x0000000B - 0x001D0180 / 0x0000000B - 0x001D0180
read txd
~~~~~~~~
-Display a TX descriptor for a port TX queue:
+Display a TX descriptor for a port TX queue::
+
+ testpmd> read txd (port_id) (queue_id) (txd_id)
+
+For example::
+
+ testpmd> read txd 0 0 4
+ 0x00000001 - 0x24C3C440 / 0x000F0000 - 0x2330003C
+
+ddp get list
+~~~~~~~~~~~~
+
+Get loaded dynamic device personalization (DDP) package info list::
+
+ testpmd> ddp get list (port_id)
+
+ddp get info
+~~~~~~~~~~~~
+
+Display information about dynamic device personalization (DDP) profile::
+
+ testpmd> ddp get info (profile_path)
+
+show vf stats
+~~~~~~~~~~~~~
+
+Display VF statistics::
+
+ testpmd> show vf stats (port_id) (vf_id)
+
+clear vf stats
+~~~~~~~~~~~~~~
+
+Reset VF statistics::
+
+ testpmd> clear vf stats (port_id) (vf_id)
+
+show port pctype mapping
+~~~~~~~~~~~~~~~~~~~~~~~~
+
+List all items from the pctype mapping table::
+
+ testpmd> show port (port_id) pctype mapping
+
+show rx offloading capabilities
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+List all per queue and per port Rx offloading capabilities of a port::
+
+ testpmd> show port (port_id) rx_offload capabilities
+
+show rx offloading configuration
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+List port level and all queue level Rx offloading configuration::
+
+ testpmd> show port (port_id) rx_offload configuration
+
+show tx offloading capabilities
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+List all per queue and per port Tx offloading capabilities of a port::
+
+ testpmd> show port (port_id) tx_offload capabilities
+
+show tx offloading configuration
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+List port level and all queue level Tx offloading configuration::
+
+ testpmd> show port (port_id) tx_offload configuration
+
+show tx metadata setting
+~~~~~~~~~~~~~~~~~~~~~~~~
+
+Show Tx metadata value set for a specific port::
-read txd (port_id) (queue_id) (txd_id)
+ testpmd> show port (port_id) tx_metadata
+
+show port supported ptypes
+~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+Show ptypes supported for a specific port::
+
+ testpmd> show port (port_id) ptypes
+
+set port supported ptypes
+~~~~~~~~~~~~~~~~~~~~~~~~~
+
+set packet types classification for a specific port::
+
+ testpmd> set port (port_id) ptypes_mask (mask)
+
+show port mac addresses info
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+Show mac addresses added for a specific port::
+
+ testpmd> show port (port_id) macs
+
+
+show port multicast mac addresses info
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+Show multicast mac addresses added for a specific port::
+
+ testpmd> show port (port_id) mcast_macs
+
+show device info
+~~~~~~~~~~~~~~~~
+
+Show general information about devices probed::
+
+ testpmd> show device info (<identifier>|all)
For example:
.. code-block:: console
- testpmd> read txd 0 0 4
- 0x00000001 - 0x24C3C440 / 0x000F0000 - 0x2330003C
+ testpmd> show device info net_pcap0
+
+ ********************* Infos for device net_pcap0 *********************
+ Bus name: vdev
+ Driver name: net_pcap
+ Devargs: iface=enP2p6s0,phy_mac=1
+ Connect to socket: -1
+
+ Port id: 2
+ MAC address: 1E:37:93:28:04:B8
+ Device name: net_pcap0
+
+dump physmem
+~~~~~~~~~~~~
+
+Dumps all physical memory segment layouts::
+
+ testpmd> dump_physmem
+
+dump memzone
+~~~~~~~~~~~~
+
+Dumps the layout of all memory zones::
+
+ testpmd> dump_memzone
+
+dump socket memory
+~~~~~~~~~~~~~~~~~~
+
+Dumps the memory usage of all sockets::
+
+ testpmd> dump_socket_mem
+
+dump struct size
+~~~~~~~~~~~~~~~~
+
+Dumps the size of all memory structures::
+
+ testpmd> dump_struct_sizes
+
+dump ring
+~~~~~~~~~
+
+Dumps the status of all or specific element in DPDK rings::
+
+ testpmd> dump_ring [ring_name]
+
+dump mempool
+~~~~~~~~~~~~
+
+Dumps the statistics of all or specific memory pool::
+
+ testpmd> dump_mempool [mempool_name]
+
+dump devargs
+~~~~~~~~~~~~
+
+Dumps the user device list::
+
+ testpmd> dump_devargs
+
+dump log types
+~~~~~~~~~~~~~~
+
+Dumps the log level for all the dpdk modules::
+
+ testpmd> dump_log_types
+
+show (raw_encap|raw_decap)
+~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+Display content of raw_encap/raw_decap buffers in hex::
+
+ testpmd> show <raw_encap|raw_decap> <index>
+ testpmd> show <raw_encap|raw_decap> all
+
+For example::
+
+ testpmd> show raw_encap 6
+
+ index: 6 at [0x1c565b0], len=50
+ 00000000: 00 00 00 00 00 00 16 26 36 46 56 66 08 00 45 00 | .......&6FVf..E.
+ 00000010: 00 00 00 00 00 00 00 11 00 00 C0 A8 01 06 C0 A8 | ................
+ 00000020: 03 06 00 00 00 FA 00 00 00 00 08 00 00 00 00 00 | ................
+ 00000030: 06 00 | ..
+
Configuration Functions
-----------------------
.. note::
- Configuration changes only become active when forwarding is started/restarted.
+ Configuration changes only become active when forwarding is started/restarted.
set default
~~~~~~~~~~~
-Reset forwarding to the default configuration:
+Reset forwarding to the default configuration::
-set default
+ testpmd> set default
set verbose
~~~~~~~~~~~
-Set the debug verbosity level:
+Set the debug verbosity level::
-set verbose (level)
+ testpmd> set verbose (level)
-Currently the only available levels are 0 (silent except for error) and 1 (fully verbose).
+Available levels are as following:
+
+* ``0`` silent except for error.
+* ``1`` fully verbose except for Tx packets.
+* ``2`` fully verbose except for Rx packets.
+* ``> 2`` fully verbose.
+
+set log
+~~~~~~~
+
+Set the log level for a log type::
+
+ testpmd> set log global|(type) (level)
+
+Where:
+
+* ``type`` is the log name.
+
+* ``level`` is the log level.
+
+For example, to change the global log level::
+
+ testpmd> set log global (level)
+
+Regexes can also be used for type. To change log level of user1, user2 and user3::
+
+ testpmd> set log user[1-3] (level)
set nbport
~~~~~~~~~~
set nbport (num)
-This is equivalent to the --nb-ports command-line option.
+This is equivalent to the ``--nb-ports`` command-line option.
set nbcore
~~~~~~~~~~
-Set the number of cores used by the application:
+Set the number of cores used by the application::
-set nbcore (num)
+ testpmd> set nbcore (num)
-This is equivalent to the --nb-cores command-line option.
+This is equivalent to the ``--nb-cores`` command-line option.
.. note::
- The number of cores used must not be greater than number of ports used multiplied by the number of queues per port.
+ The number of cores used must not be greater than number of ports used multiplied by the number of queues per port.
set coremask
~~~~~~~~~~~~
-Set the forwarding cores hexadecimal mask:
+Set the forwarding cores hexadecimal mask::
-set coremask (mask)
+ testpmd> set coremask (mask)
-This is equivalent to the --coremask command-line option.
+This is equivalent to the ``--coremask`` command-line option.
.. note::
- The master lcore is reserved for command line parsing only and cannot be masked on for packet forwarding.
+ The master lcore is reserved for command line parsing only and cannot be masked on for packet forwarding.
set portmask
~~~~~~~~~~~~
-Set the forwarding ports hexadecimal mask:
+Set the forwarding ports hexadecimal mask::
-set portmask (mask)
+ testpmd> set portmask (mask)
-This is equivalent to the --portmask command-line option.
+This is equivalent to the ``--portmask`` command-line option.
set burst
~~~~~~~~~
-Set number of packets per burst:
+Set number of packets per burst::
-set burst (num)
+ testpmd> set burst (num)
-This is equivalent to the --burst command-line option.
+This is equivalent to the ``--burst command-line`` option.
-In mac_retry forwarding mode, the transmit delay time and number of retries can also be set.
+When retry is enabled, the transmit delay time and number of retries can also be set::
-set burst tx delay (micrseconds) retry (num)
+ testpmd> set burst tx delay (microseconds) retry (num)
set txpkts
~~~~~~~~~~
-Set the length of each segment of the TX-ONLY packets:
+Set the length of each segment of the TX-ONLY packets or length of packet for FLOWGEN mode::
-set txpkts (x[,y]*)
+ testpmd> set txpkts (x[,y]*)
Where x[,y]* represents a CSV list of values, without white space.
+set txsplit
+~~~~~~~~~~~
+
+Set the split policy for the TX packets, applicable for TX-ONLY and CSUM forwarding modes::
+
+ testpmd> set txsplit (off|on|rand)
+
+Where:
+
+* ``off`` disable packet copy & split for CSUM mode.
+
+* ``on`` split outgoing packet into multiple segments. Size of each segment
+ and number of segments per packet is determined by ``set txpkts`` command
+ (see above).
+
+* ``rand`` same as 'on', but number of segments per each packet is a random value between 1 and total number of segments.
+
set corelist
~~~~~~~~~~~~
-Set the list of forwarding cores:
+Set the list of forwarding cores::
-set corelist (x[,y]*)
+ testpmd> set corelist (x[,y]*)
For example, to change the forwarding cores:
.. code-block:: console
- testpmd> set corelist 3,1
- testpmd> show config fwd
+ testpmd> set corelist 3,1
+ testpmd> show config fwd
- io packet forwarding - ports=2 - cores=2 - streams=2 - NUMA support disabled
- Logical Core 3 (socket 0) forwards packets on 1 streams:
- RX P=0/Q=0 (socket 0) -> TX P=1/Q=0 (socket 0) peer=02:00:00:00:00:01
- Logical Core 1 (socket 0) forwards packets on 1 streams:
- RX P=1/Q=0 (socket 0) -> TX P=0/Q=0 (socket 0) peer=02:00:00:00:00:00
+ io packet forwarding - ports=2 - cores=2 - streams=2 - NUMA support disabled
+ Logical Core 3 (socket 0) forwards packets on 1 streams:
+ RX P=0/Q=0 (socket 0) -> TX P=1/Q=0 (socket 0) peer=02:00:00:00:00:01
+ Logical Core 1 (socket 0) forwards packets on 1 streams:
+ RX P=1/Q=0 (socket 0) -> TX P=0/Q=0 (socket 0) peer=02:00:00:00:00:00
.. note::
- The cores are used in the same order as specified on the command line.
+ The cores are used in the same order as specified on the command line.
set portlist
~~~~~~~~~~~~
-Set the list of forwarding ports:
+Set the list of forwarding ports::
-set portlist (x[,y]*)
+ testpmd> set portlist (x[,y]*)
For example, to change the port forwarding:
.. code-block:: console
- testpmd> set portlist 0,2,1,3
- testpmd> show config fwd
+ testpmd> set portlist 0,2,1,3
+ testpmd> show config fwd
- io packet forwarding - ports=4 - cores=1 - streams=4
- Logical Core 3 (socket 0) forwards packets on 4 streams:
- RX P=0/Q=0 (socket 0) -> TX P=2/Q=0 (socket 0) peer=02:00:00:00:00:01
- RX P=2/Q=0 (socket 0) -> TX P=0/Q=0 (socket 0) peer=02:00:00:00:00:00
- RX P=1/Q=0 (socket 0) -> TX P=3/Q=0 (socket 0) peer=02:00:00:00:00:03
- RX P=3/Q=0 (socket 0) -> TX P=1/Q=0 (socket 0) peer=02:00:00:00:00:02
+ io packet forwarding - ports=4 - cores=1 - streams=4
+ Logical Core 3 (socket 0) forwards packets on 4 streams:
+ RX P=0/Q=0 (socket 0) -> TX P=2/Q=0 (socket 0) peer=02:00:00:00:00:01
+ RX P=2/Q=0 (socket 0) -> TX P=0/Q=0 (socket 0) peer=02:00:00:00:00:00
+ RX P=1/Q=0 (socket 0) -> TX P=3/Q=0 (socket 0) peer=02:00:00:00:00:03
+ RX P=3/Q=0 (socket 0) -> TX P=1/Q=0 (socket 0) peer=02:00:00:00:00:02
-vlan set strip
-~~~~~~~~~~~~~~
+set port setup on
+~~~~~~~~~~~~~~~~~
-Set the VLAN strip on a port:
+Select how to retrieve new ports created after "port attach" command::
-vlan set strip (on|off) (port_id)
+ testpmd> set port setup on (iterator|event)
-vlan set stripq
+For each new port, a setup is done.
+It will find the probed ports via RTE_ETH_FOREACH_MATCHING_DEV loop
+in iterator mode, or via RTE_ETH_EVENT_NEW in event mode.
+
+set tx loopback
~~~~~~~~~~~~~~~
-Set the VLAN strip for a queue on a port:
+Enable/disable tx loopback::
-vlan set stripq (on|off) (port_id,queue_id)
+ testpmd> set tx loopback (port_id) (on|off)
-vlan set filter
+set drop enable
~~~~~~~~~~~~~~~
-Set the VLAN filter on a port:
+set drop enable bit for all queues::
-vlan set filter (on|off) (port_id)
+ testpmd> set all queues drop (port_id) (on|off)
-vlan set qinq
-~~~~~~~~~~~~~
+set split drop enable (for VF)
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
-Set the VLAN QinQ (extended queue in queue) on for a port:
+set split drop enable bit for VF from PF::
-vlan set qinq (on|off) (port_id)
+ testpmd> set vf split drop (port_id) (vf_id) (on|off)
-vlan set tpid
+set mac antispoof (for VF)
+~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+Set mac antispoof for a VF from the PF::
+
+ testpmd> set vf mac antispoof (port_id) (vf_id) (on|off)
+
+set macsec offload
+~~~~~~~~~~~~~~~~~~
+
+Enable/disable MACsec offload::
+
+ testpmd> set macsec offload (port_id) on encrypt (on|off) replay-protect (on|off)
+ testpmd> set macsec offload (port_id) off
+
+set macsec sc
~~~~~~~~~~~~~
-Set the outer VLAN TPID for packet filtering on a port:
+Configure MACsec secure connection (SC)::
-vlan set tpid (value) (port_id)
+ testpmd> set macsec sc (tx|rx) (port_id) (mac) (pi)
.. note::
- TPID value must be a 16-bit number (value <= 65536).
+ The pi argument is ignored for tx.
+ Check the NIC Datasheet for hardware limits.
-rx_vlan add
-~~~~~~~~~~~
+set macsec sa
+~~~~~~~~~~~~~
-Add a VLAN ID, or all identifiers, to the set of VLAN identifiers filtered by port ID:
+Configure MACsec secure association (SA)::
-rx_vlan add (vlan_id|all) (port_id)
+ testpmd> set macsec sa (tx|rx) (port_id) (idx) (an) (pn) (key)
.. note::
- VLAN filter must be set on that port. VLAN ID < 4096.
+ The IDX value must be 0 or 1.
+ Check the NIC Datasheet for hardware limits.
-rx_vlan rm
-~~~~~~~~~~
+set broadcast mode (for VF)
+~~~~~~~~~~~~~~~~~~~~~~~~~~~
-Remove a VLAN ID, or all identifiers, from the set of VLAN identifiers filtered by port ID:
+Set broadcast mode for a VF from the PF::
-rx_vlan rm (vlan_id|all) (port_id)
+ testpmd> set vf broadcast (port_id) (vf_id) (on|off)
-rx_vlan add(for VF)
-~~~~~~~~~~~~~~~~~~~
+vlan set stripq
+~~~~~~~~~~~~~~~
-Add a VLAN ID, to the set of VLAN identifiers filtered for VF(s) for port ID:
+Set the VLAN strip for a queue on a port::
-rx_vlan add (vlan_id) port (port_id) vf (vf_mask)
+ testpmd> vlan set stripq (on|off) (port_id,queue_id)
-rx_vlan rm(for VF)
-~~~~~~~~~~~~~~~~~~
+vlan set stripq (for VF)
+~~~~~~~~~~~~~~~~~~~~~~~~
-Remove a VLAN ID, from the set of VLAN identifiers filtered for VF(s) for port ID:
+Set VLAN strip for all queues in a pool for a VF from the PF::
-rx_vlan rm (vlan_id) port (port_id) vf (vf_mask)
+ testpmd> set vf vlan stripq (port_id) (vf_id) (on|off)
-rx_vlan set tpid
-~~~~~~~~~~~~~~~~
+vlan set insert (for VF)
+~~~~~~~~~~~~~~~~~~~~~~~~
-Set the outer VLAN TPID for packet filtering on a port:
+Set VLAN insert for a VF from the PF::
-rx_vlan set tpid (value) (port_id)
+ testpmd> set vf vlan insert (port_id) (vf_id) (vlan_id)
-tunnel_filter add
-~~~~~~~~~~~~~~~~~
+vlan set tag (for VF)
+~~~~~~~~~~~~~~~~~~~~~
+
+Set VLAN tag for a VF from the PF::
+
+ testpmd> set vf vlan tag (port_id) (vf_id) (on|off)
+
+vlan set antispoof (for VF)
+~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+Set VLAN antispoof for a VF from the PF::
+
+ testpmd> set vf vlan antispoof (port_id) (vf_id) (on|off)
+
+vlan set (strip|filter|qinq_strip|extend)
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+Set the VLAN strip/filter/QinQ strip/extend on for a port::
+
+ testpmd> vlan set (strip|filter|qinq_strip|extend) (on|off) (port_id)
+
+vlan set tpid
+~~~~~~~~~~~~~
+
+Set the inner or outer VLAN TPID for packet filtering on a port::
+
+ testpmd> vlan set (inner|outer) tpid (value) (port_id)
+
+.. note::
+
+ TPID value must be a 16-bit number (value <= 65536).
+
+rx_vlan add
+~~~~~~~~~~~
+
+Add a VLAN ID, or all identifiers, to the set of VLAN identifiers filtered by port ID::
+
+ testpmd> rx_vlan add (vlan_id|all) (port_id)
+
+.. note::
+
+ VLAN filter must be set on that port. VLAN ID < 4096.
+ Depending on the NIC used, number of vlan_ids may be limited to the maximum entries
+ in VFTA table. This is important if enabling all vlan_ids.
+
+rx_vlan rm
+~~~~~~~~~~
+
+Remove a VLAN ID, or all identifiers, from the set of VLAN identifiers filtered by port ID::
+
+ testpmd> rx_vlan rm (vlan_id|all) (port_id)
+
+rx_vlan add (for VF)
+~~~~~~~~~~~~~~~~~~~~
+
+Add a VLAN ID, to the set of VLAN identifiers filtered for VF(s) for port ID::
+
+ testpmd> rx_vlan add (vlan_id) port (port_id) vf (vf_mask)
+
+rx_vlan rm (for VF)
+~~~~~~~~~~~~~~~~~~~
+
+Remove a VLAN ID, from the set of VLAN identifiers filtered for VF(s) for port ID::
+
+ testpmd> rx_vlan rm (vlan_id) port (port_id) vf (vf_mask)
+
+tunnel_filter add
+~~~~~~~~~~~~~~~~~
+
+Add a tunnel filter on a port::
+
+ testpmd> tunnel_filter add (port_id) (outer_mac) (inner_mac) (ip_addr) \
+ (inner_vlan) (vxlan|nvgre|ipingre|vxlan-gpe) (imac-ivlan|imac-ivlan-tenid|\
+ imac-tenid|imac|omac-imac-tenid|oip|iip) (tenant_id) (queue_id)
+
+The available information categories are:
+
+* ``vxlan``: Set tunnel type as VXLAN.
+
+* ``nvgre``: Set tunnel type as NVGRE.
+
+* ``ipingre``: Set tunnel type as IP-in-GRE.
+
+* ``vxlan-gpe``: Set tunnel type as VXLAN-GPE
+
+* ``imac-ivlan``: Set filter type as Inner MAC and VLAN.
+
+* ``imac-ivlan-tenid``: Set filter type as Inner MAC, VLAN and tenant ID.
+
+* ``imac-tenid``: Set filter type as Inner MAC and tenant ID.
+
+* ``imac``: Set filter type as Inner MAC.
+
+* ``omac-imac-tenid``: Set filter type as Outer MAC, Inner MAC and tenant ID.
+
+* ``oip``: Set filter type as Outer IP.
+
+* ``iip``: Set filter type as Inner IP.
+
+Example::
+
+ testpmd> tunnel_filter add 0 68:05:CA:28:09:82 00:00:00:00:00:00 \
+ 192.168.2.2 0 ipingre oip 1 1
+
+ Set an IP-in-GRE tunnel on port 0, and the filter type is Outer IP.
+
+tunnel_filter remove
+~~~~~~~~~~~~~~~~~~~~
+
+Remove a tunnel filter on a port::
+
+ testpmd> tunnel_filter rm (port_id) (outer_mac) (inner_mac) (ip_addr) \
+ (inner_vlan) (vxlan|nvgre|ipingre|vxlan-gpe) (imac-ivlan|imac-ivlan-tenid|\
+ imac-tenid|imac|omac-imac-tenid|oip|iip) (tenant_id) (queue_id)
+
+rx_vxlan_port add
+~~~~~~~~~~~~~~~~~
+
+Add an UDP port for VXLAN packet filter on a port::
+
+ testpmd> rx_vxlan_port add (udp_port) (port_id)
+
+rx_vxlan_port remove
+~~~~~~~~~~~~~~~~~~~~
+
+Remove an UDP port for VXLAN packet filter on a port::
+
+ testpmd> rx_vxlan_port rm (udp_port) (port_id)
+
+tx_vlan set
+~~~~~~~~~~~
+
+Set hardware insertion of VLAN IDs in packets sent on a port::
+
+ testpmd> tx_vlan set (port_id) vlan_id[, vlan_id_outer]
+
+For example, set a single VLAN ID (5) insertion on port 0::
+
+ tx_vlan set 0 5
+
+Or, set double VLAN ID (inner: 2, outer: 3) insertion on port 1::
+
+ tx_vlan set 1 2 3
+
+
+tx_vlan set pvid
+~~~~~~~~~~~~~~~~
+
+Set port based hardware insertion of VLAN ID in packets sent on a port::
+
+ testpmd> tx_vlan set pvid (port_id) (vlan_id) (on|off)
+
+tx_vlan reset
+~~~~~~~~~~~~~
+
+Disable hardware insertion of a VLAN header in packets sent on a port::
+
+ testpmd> tx_vlan reset (port_id)
+
+csum set
+~~~~~~~~
+
+Select hardware or software calculation of the checksum when
+transmitting a packet using the ``csum`` forwarding engine::
+
+ testpmd> csum set (ip|udp|tcp|sctp|outer-ip|outer-udp) (hw|sw) (port_id)
+
+Where:
+
+* ``ip|udp|tcp|sctp`` always relate to the inner layer.
+
+* ``outer-ip`` relates to the outer IP layer (only for IPv4) in the case where the packet is recognized
+ as a tunnel packet by the forwarding engine (vxlan, gre and ipip are
+ supported). See also the ``csum parse-tunnel`` command.
+
+* ``outer-udp`` relates to the outer UDP layer in the case where the packet is recognized
+ as a tunnel packet by the forwarding engine (vxlan, vxlan-gpe are
+ supported). See also the ``csum parse-tunnel`` command.
+
+.. note::
+
+ Check the NIC Datasheet for hardware limits.
+
+RSS queue region
+~~~~~~~~~~~~~~~~
+
+Set RSS queue region span on a port::
+
+ testpmd> set port (port_id) queue-region region_id (value) \
+ queue_start_index (value) queue_num (value)
+
+Set flowtype mapping on a RSS queue region on a port::
+
+ testpmd> set port (port_id) queue-region region_id (value) flowtype (value)
+
+where:
+
+* For the flowtype(pctype) of packet,the specific index for each type has
+ been defined in file i40e_type.h as enum i40e_filter_pctype.
+
+Set user priority mapping on a RSS queue region on a port::
+
+ testpmd> set port (port_id) queue-region UP (value) region_id (value)
+
+Flush all queue region related configuration on a port::
+
+ testpmd> set port (port_id) queue-region flush (on|off)
+
+where:
+
+* ``on``: is just an enable function which server for other configuration,
+ it is for all configuration about queue region from up layer,
+ at first will only keep in DPDK software stored in driver,
+ only after "flush on", it commit all configuration to HW.
+
+* ``"off``: is just clean all configuration about queue region just now,
+ and restore all to DPDK i40e driver default config when start up.
+
+Show all queue region related configuration info on a port::
+
+ testpmd> show port (port_id) queue-region
+
+.. note::
+
+ Queue region only support on PF by now, so these command is
+ only for configuration of queue region on PF port.
+
+csum parse-tunnel
+~~~~~~~~~~~~~~~~~
+
+Define how tunneled packets should be handled by the csum forward
+engine::
+
+ testpmd> csum parse-tunnel (on|off) (tx_port_id)
+
+If enabled, the csum forward engine will try to recognize supported
+tunnel headers (vxlan, gre, ipip).
+
+If disabled, treat tunnel packets as non-tunneled packets (a inner
+header is handled as a packet payload).
+
+.. note::
+
+ The port argument is the TX port like in the ``csum set`` command.
+
+Example:
+
+Consider a packet in packet like the following::
+
+ eth_out/ipv4_out/udp_out/vxlan/eth_in/ipv4_in/tcp_in
+
+* If parse-tunnel is enabled, the ``ip|udp|tcp|sctp`` parameters of ``csum set``
+ command relate to the inner headers (here ``ipv4_in`` and ``tcp_in``), and the
+ ``outer-ip|outer-udp`` parameter relates to the outer headers (here ``ipv4_out`` and ``udp_out``).
+
+* If parse-tunnel is disabled, the ``ip|udp|tcp|sctp`` parameters of ``csum set``
+ command relate to the outer headers, here ``ipv4_out`` and ``udp_out``.
+
+csum show
+~~~~~~~~~
+
+Display tx checksum offload configuration::
+
+ testpmd> csum show (port_id)
+
+tso set
+~~~~~~~
+
+Enable TCP Segmentation Offload (TSO) in the ``csum`` forwarding engine::
+
+ testpmd> tso set (segsize) (port_id)
+
+.. note::
+
+ Check the NIC datasheet for hardware limits.
+
+tso show
+~~~~~~~~
+
+Display the status of TCP Segmentation Offload::
+
+ testpmd> tso show (port_id)
+
+tunnel tso set
+~~~~~~~~~~~~~~
+
+Set tso segment size of tunneled packets for a port in csum engine::
+
+ testpmd> tunnel_tso set (tso_segsz) (port_id)
+
+tunnel tso show
+~~~~~~~~~~~~~~~
+
+Display the status of tunneled TCP Segmentation Offload for a port::
+
+ testpmd> tunnel_tso show (port_id)
+
+set port - gro
+~~~~~~~~~~~~~~
+
+Enable or disable GRO in ``csum`` forwarding engine::
+
+ testpmd> set port <port_id> gro on|off
+
+If enabled, the csum forwarding engine will perform GRO on the TCP/IPv4
+packets received from the given port.
+
+If disabled, packets received from the given port won't be performed
+GRO. By default, GRO is disabled for all ports.
+
+.. note::
+
+ When enable GRO for a port, TCP/IPv4 packets received from the port
+ will be performed GRO. After GRO, all merged packets have bad
+ checksums, since the GRO library doesn't re-calculate checksums for
+ the merged packets. Therefore, if users want the merged packets to
+ have correct checksums, please select HW IP checksum calculation and
+ HW TCP checksum calculation for the port which the merged packets are
+ transmitted to.
+
+show port - gro
+~~~~~~~~~~~~~~~
+
+Display GRO configuration for a given port::
+
+ testpmd> show port <port_id> gro
+
+set gro flush
+~~~~~~~~~~~~~
+
+Set the cycle to flush the GROed packets from reassembly tables::
+
+ testpmd> set gro flush <cycles>
+
+When enable GRO, the csum forwarding engine performs GRO on received
+packets, and the GROed packets are stored in reassembly tables. Users
+can use this command to determine when the GROed packets are flushed
+from the reassembly tables.
+
+The ``cycles`` is measured in GRO operation times. The csum forwarding
+engine flushes the GROed packets from the tables every ``cycles`` GRO
+operations.
+
+By default, the value of ``cycles`` is 1, which means flush GROed packets
+from the reassembly tables as soon as one GRO operation finishes. The value
+of ``cycles`` should be in the range of 1 to ``GRO_MAX_FLUSH_CYCLES``.
+
+Please note that the large value of ``cycles`` may cause the poor TCP/IP
+stack performance. Because the GROed packets are delayed to arrive the
+stack, thus causing more duplicated ACKs and TCP retransmissions.
+
+set port - gso
+~~~~~~~~~~~~~~
+
+Toggle per-port GSO support in ``csum`` forwarding engine::
+
+ testpmd> set port <port_id> gso on|off
+
+If enabled, the csum forwarding engine will perform GSO on supported IPv4
+packets, transmitted on the given port.
+
+If disabled, packets transmitted on the given port will not undergo GSO.
+By default, GSO is disabled for all ports.
+
+.. note::
+
+ When GSO is enabled on a port, supported IPv4 packets transmitted on that
+ port undergo GSO. Afterwards, the segmented packets are represented by
+ multi-segment mbufs; however, the csum forwarding engine doesn't calculation
+ of checksums for GSO'd segments in SW. As a result, if users want correct
+ checksums in GSO segments, they should enable HW checksum calculation for
+ GSO-enabled ports.
+
+ For example, HW checksum calculation for VxLAN GSO'd packets may be enabled
+ by setting the following options in the csum forwarding engine:
+
+ testpmd> csum set outer_ip hw <port_id>
+
+ testpmd> csum set ip hw <port_id>
+
+ testpmd> csum set tcp hw <port_id>
+
+ UDP GSO is the same as IP fragmentation, which treats the UDP header
+ as the payload and does not modify it during segmentation. That is,
+ after UDP GSO, only the first output fragment has the original UDP
+ header. Therefore, users need to enable HW IP checksum calculation
+ and SW UDP checksum calculation for GSO-enabled ports, if they want
+ correct checksums for UDP/IPv4 packets.
+
+set gso segsz
+~~~~~~~~~~~~~
+
+Set the maximum GSO segment size (measured in bytes), which includes the
+packet header and the packet payload for GSO-enabled ports (global)::
+
+ testpmd> set gso segsz <length>
+
+show port - gso
+~~~~~~~~~~~~~~~
+
+Display the status of Generic Segmentation Offload for a given port::
+
+ testpmd> show port <port_id> gso
+
+mac_addr add
+~~~~~~~~~~~~
+
+Add an alternative MAC address to a port::
+
+ testpmd> mac_addr add (port_id) (XX:XX:XX:XX:XX:XX)
+
+mac_addr remove
+~~~~~~~~~~~~~~~
+
+Remove a MAC address from a port::
+
+ testpmd> mac_addr remove (port_id) (XX:XX:XX:XX:XX:XX)
+
+mcast_addr add
+~~~~~~~~~~~~~~
+
+To add the multicast MAC address to/from the set of multicast addresses
+filtered by port::
+
+ testpmd> mcast_addr add (port_id) (mcast_addr)
+
+mcast_addr remove
+~~~~~~~~~~~~~~~~~
+
+To remove the multicast MAC address to/from the set of multicast addresses
+filtered by port::
+
+ testpmd> mcast_addr remove (port_id) (mcast_addr)
+
+mac_addr add (for VF)
+~~~~~~~~~~~~~~~~~~~~~
+
+Add an alternative MAC address for a VF to a port::
+
+ testpmd> mac_add add port (port_id) vf (vf_id) (XX:XX:XX:XX:XX:XX)
+
+mac_addr set
+~~~~~~~~~~~~
+
+Set the default MAC address for a port::
+
+ testpmd> mac_addr set (port_id) (XX:XX:XX:XX:XX:XX)
+
+mac_addr set (for VF)
+~~~~~~~~~~~~~~~~~~~~~
+
+Set the MAC address for a VF from the PF::
+
+ testpmd> set vf mac addr (port_id) (vf_id) (XX:XX:XX:XX:XX:XX)
+
+set eth-peer
+~~~~~~~~~~~~
+
+Set the forwarding peer address for certain port::
+
+ testpmd> set eth-peer (port_id) (peer_addr)
+
+This is equivalent to the ``--eth-peer`` command-line option.
+
+set port-uta
+~~~~~~~~~~~~
+
+Set the unicast hash filter(s) on/off for a port::
+
+ testpmd> set port (port_id) uta (XX:XX:XX:XX:XX:XX|all) (on|off)
+
+set promisc
+~~~~~~~~~~~
+
+Set the promiscuous mode on for a port or for all ports.
+In promiscuous mode packets are not dropped if they aren't for the specified MAC address::
+
+ testpmd> set promisc (port_id|all) (on|off)
+
+set allmulti
+~~~~~~~~~~~~
+
+Set the allmulti mode for a port or for all ports::
+
+ testpmd> set allmulti (port_id|all) (on|off)
+
+Same as the ifconfig (8) option. Controls how multicast packets are handled.
+
+set promisc (for VF)
+~~~~~~~~~~~~~~~~~~~~
+
+Set the unicast promiscuous mode for a VF from PF.
+It's supported by Intel i40e NICs now.
+In promiscuous mode packets are not dropped if they aren't for the specified MAC address::
+
+ testpmd> set vf promisc (port_id) (vf_id) (on|off)
+
+set allmulticast (for VF)
+~~~~~~~~~~~~~~~~~~~~~~~~~
+
+Set the multicast promiscuous mode for a VF from PF.
+It's supported by Intel i40e NICs now.
+In promiscuous mode packets are not dropped if they aren't for the specified MAC address::
+
+ testpmd> set vf allmulti (port_id) (vf_id) (on|off)
+
+set tx max bandwidth (for VF)
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+Set TX max absolute bandwidth (Mbps) for a VF from PF::
+
+ testpmd> set vf tx max-bandwidth (port_id) (vf_id) (max_bandwidth)
+
+set tc tx min bandwidth (for VF)
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+Set all TCs' TX min relative bandwidth (%) for a VF from PF::
+
+ testpmd> set vf tc tx min-bandwidth (port_id) (vf_id) (bw1, bw2, ...)
+
+set tc tx max bandwidth (for VF)
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+Set a TC's TX max absolute bandwidth (Mbps) for a VF from PF::
+
+ testpmd> set vf tc tx max-bandwidth (port_id) (vf_id) (tc_no) (max_bandwidth)
+
+set tc strict link priority mode
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+Set some TCs' strict link priority mode on a physical port::
+
+ testpmd> set tx strict-link-priority (port_id) (tc_bitmap)
+
+set tc tx min bandwidth
+~~~~~~~~~~~~~~~~~~~~~~~
+
+Set all TCs' TX min relative bandwidth (%) globally for all PF and VFs::
+
+ testpmd> set tc tx min-bandwidth (port_id) (bw1, bw2, ...)
+
+set flow_ctrl rx
+~~~~~~~~~~~~~~~~
+
+Set the link flow control parameter on a port::
+
+ testpmd> set flow_ctrl rx (on|off) tx (on|off) (high_water) (low_water) \
+ (pause_time) (send_xon) mac_ctrl_frame_fwd (on|off) \
+ autoneg (on|off) (port_id)
+
+Where:
+
+* ``high_water`` (integer): High threshold value to trigger XOFF.
+
+* ``low_water`` (integer): Low threshold value to trigger XON.
+
+* ``pause_time`` (integer): Pause quota in the Pause frame.
+
+* ``send_xon`` (0/1): Send XON frame.
+
+* ``mac_ctrl_frame_fwd``: Enable receiving MAC control frames.
+
+* ``autoneg``: Change the auto-negotiation parameter.
+
+set pfc_ctrl rx
+~~~~~~~~~~~~~~~
+
+Set the priority flow control parameter on a port::
+
+ testpmd> set pfc_ctrl rx (on|off) tx (on|off) (high_water) (low_water) \
+ (pause_time) (priority) (port_id)
+
+Where:
+
+* ``high_water`` (integer): High threshold value.
+
+* ``low_water`` (integer): Low threshold value.
+
+* ``pause_time`` (integer): Pause quota in the Pause frame.
+
+* ``priority`` (0-7): VLAN User Priority.
+
+set stat_qmap
+~~~~~~~~~~~~~
+
+Set statistics mapping (qmapping 0..15) for RX/TX queue on port::
+
+ testpmd> set stat_qmap (tx|rx) (port_id) (queue_id) (qmapping)
+
+For example, to set rx queue 2 on port 0 to mapping 5::
+
+ testpmd>set stat_qmap rx 0 2 5
+
+set xstats-hide-zero
+~~~~~~~~~~~~~~~~~~~~
+
+Set the option to hide zero values for xstats display::
+
+ testpmd> set xstats-hide-zero on|off
+
+.. note::
+
+ By default, the zero values are displayed for xstats.
+
+set port - rx/tx (for VF)
+~~~~~~~~~~~~~~~~~~~~~~~~~
+
+Set VF receive/transmit from a port::
+
+ testpmd> set port (port_id) vf (vf_id) (rx|tx) (on|off)
+
+set port - mac address filter (for VF)
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+Add/Remove unicast or multicast MAC addr filter for a VF::
+
+ testpmd> set port (port_id) vf (vf_id) (mac_addr) \
+ (exact-mac|exact-mac-vlan|hashmac|hashmac-vlan) (on|off)
+
+set port - rx mode(for VF)
+~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+Set the VF receive mode of a port::
+
+ testpmd> set port (port_id) vf (vf_id) \
+ rxmode (AUPE|ROPE|BAM|MPE) (on|off)
+
+The available receive modes are:
+
+* ``AUPE``: Accepts untagged VLAN.
+
+* ``ROPE``: Accepts unicast hash.
+
+* ``BAM``: Accepts broadcast packets.
+
+* ``MPE``: Accepts all multicast packets.
+
+set port - tx_rate (for Queue)
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+Set TX rate limitation for a queue on a port::
+
+ testpmd> set port (port_id) queue (queue_id) rate (rate_value)
+
+set port - tx_rate (for VF)
+~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+Set TX rate limitation for queues in VF on a port::
+
+ testpmd> set port (port_id) vf (vf_id) rate (rate_value) queue_mask (queue_mask)
+
+set port - mirror rule
+~~~~~~~~~~~~~~~~~~~~~~
+
+Set pool or vlan type mirror rule for a port::
+
+ testpmd> set port (port_id) mirror-rule (rule_id) \
+ (pool-mirror-up|pool-mirror-down|vlan-mirror) \
+ (poolmask|vlanid[,vlanid]*) dst-pool (pool_id) (on|off)
+
+Set link mirror rule for a port::
+
+ testpmd> set port (port_id) mirror-rule (rule_id) \
+ (uplink-mirror|downlink-mirror) dst-pool (pool_id) (on|off)
+
+For example to enable mirror traffic with vlan 0,1 to pool 0::
+
+ set port 0 mirror-rule 0 vlan-mirror 0,1 dst-pool 0 on
+
+reset port - mirror rule
+~~~~~~~~~~~~~~~~~~~~~~~~
+
+Reset a mirror rule for a port::
+
+ testpmd> reset port (port_id) mirror-rule (rule_id)
+
+set flush_rx
+~~~~~~~~~~~~
+
+Set the flush on RX streams before forwarding.
+The default is flush ``on``.
+Mainly used with PCAP drivers to turn off the default behavior of flushing the first 512 packets on RX streams::
+
+ testpmd> set flush_rx off
+
+set bypass mode
+~~~~~~~~~~~~~~~
+
+Set the bypass mode for the lowest port on bypass enabled NIC::
+
+ testpmd> set bypass mode (normal|bypass|isolate) (port_id)
+
+set bypass event
+~~~~~~~~~~~~~~~~
+
+Set the event required to initiate specified bypass mode for the lowest port on a bypass enabled::
+
+ testpmd> set bypass event (timeout|os_on|os_off|power_on|power_off) \
+ mode (normal|bypass|isolate) (port_id)
+
+Where:
+
+* ``timeout``: Enable bypass after watchdog timeout.
+
+* ``os_on``: Enable bypass when OS/board is powered on.
+
+* ``os_off``: Enable bypass when OS/board is powered off.
+
+* ``power_on``: Enable bypass when power supply is turned on.
+
+* ``power_off``: Enable bypass when power supply is turned off.
+
+
+set bypass timeout
+~~~~~~~~~~~~~~~~~~
+
+Set the bypass watchdog timeout to ``n`` seconds where 0 = instant::
+
+ testpmd> set bypass timeout (0|1.5|2|3|4|8|16|32)
+
+show bypass config
+~~~~~~~~~~~~~~~~~~
+
+Show the bypass configuration for a bypass enabled NIC using the lowest port on the NIC::
+
+ testpmd> show bypass config (port_id)
+
+set link up
+~~~~~~~~~~~
+
+Set link up for a port::
+
+ testpmd> set link-up port (port id)
+
+set link down
+~~~~~~~~~~~~~
+
+Set link down for a port::
+
+ testpmd> set link-down port (port id)
+
+E-tag set
+~~~~~~~~~
+
+Enable E-tag insertion for a VF on a port::
+
+ testpmd> E-tag set insertion on port-tag-id (value) port (port_id) vf (vf_id)
+
+Disable E-tag insertion for a VF on a port::
+
+ testpmd> E-tag set insertion off port (port_id) vf (vf_id)
+
+Enable/disable E-tag stripping on a port::
+
+ testpmd> E-tag set stripping (on|off) port (port_id)
+
+Enable/disable E-tag based forwarding on a port::
+
+ testpmd> E-tag set forwarding (on|off) port (port_id)
+
+Add an E-tag forwarding filter on a port::
+
+ testpmd> E-tag set filter add e-tag-id (value) dst-pool (pool_id) port (port_id)
+
+Delete an E-tag forwarding filter on a port::
+ testpmd> E-tag set filter del e-tag-id (value) port (port_id)
+
+ddp add
+~~~~~~~
+
+Load a dynamic device personalization (DDP) profile and store backup profile::
+
+ testpmd> ddp add (port_id) (profile_path[,backup_profile_path])
+
+ddp del
+~~~~~~~
+
+Delete a dynamic device personalization profile and restore backup profile::
+
+ testpmd> ddp del (port_id) (backup_profile_path)
+
+ptype mapping
+~~~~~~~~~~~~~
+
+List all items from the ptype mapping table::
+
+ testpmd> ptype mapping get (port_id) (valid_only)
+
+Where:
+
+* ``valid_only``: A flag indicates if only list valid items(=1) or all itemss(=0).
+
+Replace a specific or a group of software defined ptype with a new one::
+
+ testpmd> ptype mapping replace (port_id) (target) (mask) (pkt_type)
+
+where:
+
+* ``target``: A specific software ptype or a mask to represent a group of software ptypes.
+
+* ``mask``: A flag indicate if "target" is a specific software ptype(=0) or a ptype mask(=1).
+
+* ``pkt_type``: The new software ptype to replace the old ones.
+
+Update hardware defined ptype to software defined packet type mapping table::
+
+ testpmd> ptype mapping update (port_id) (hw_ptype) (sw_ptype)
+
+where:
+
+* ``hw_ptype``: hardware ptype as the index of the ptype mapping table.
+
+* ``sw_ptype``: software ptype as the value of the ptype mapping table.
+
+Reset ptype mapping table::
+
+ testpmd> ptype mapping reset (port_id)
+
+config per port Rx offloading
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+Enable or disable a per port Rx offloading on all Rx queues of a port::
+
+ testpmd> port config (port_id) rx_offload (offloading) on|off
+
+* ``offloading``: can be any of these offloading capability:
+ vlan_strip, ipv4_cksum, udp_cksum, tcp_cksum, tcp_lro,
+ qinq_strip, outer_ipv4_cksum, macsec_strip,
+ header_split, vlan_filter, vlan_extend, jumbo_frame,
+ scatter, timestamp, security, keep_crc, rss_hash
+
+This command should be run when the port is stopped, or else it will fail.
+
+config per queue Rx offloading
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+Enable or disable a per queue Rx offloading only on a specific Rx queue::
+
+ testpmd> port (port_id) rxq (queue_id) rx_offload (offloading) on|off
+
+* ``offloading``: can be any of these offloading capability:
+ vlan_strip, ipv4_cksum, udp_cksum, tcp_cksum, tcp_lro,
+ qinq_strip, outer_ipv4_cksum, macsec_strip,
+ header_split, vlan_filter, vlan_extend, jumbo_frame,
+ scatter, timestamp, security, keep_crc
+
+This command should be run when the port is stopped, or else it will fail.
+
+config per port Tx offloading
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+Enable or disable a per port Tx offloading on all Tx queues of a port::
+
+ testpmd> port config (port_id) tx_offload (offloading) on|off
+
+* ``offloading``: can be any of these offloading capability:
+ vlan_insert, ipv4_cksum, udp_cksum, tcp_cksum,
+ sctp_cksum, tcp_tso, udp_tso, outer_ipv4_cksum,
+ qinq_insert, vxlan_tnl_tso, gre_tnl_tso,
+ ipip_tnl_tso, geneve_tnl_tso, macsec_insert,
+ mt_lockfree, multi_segs, mbuf_fast_free, security
+
+This command should be run when the port is stopped, or else it will fail.
+
+config per queue Tx offloading
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+Enable or disable a per queue Tx offloading only on a specific Tx queue::
+
+ testpmd> port (port_id) txq (queue_id) tx_offload (offloading) on|off
+
+* ``offloading``: can be any of these offloading capability:
+ vlan_insert, ipv4_cksum, udp_cksum, tcp_cksum,
+ sctp_cksum, tcp_tso, udp_tso, outer_ipv4_cksum,
+ qinq_insert, vxlan_tnl_tso, gre_tnl_tso,
+ ipip_tnl_tso, geneve_tnl_tso, macsec_insert,
+ mt_lockfree, multi_segs, mbuf_fast_free, security
+
+This command should be run when the port is stopped, or else it will fail.
+
+Config VXLAN Encap outer layers
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+Configure the outer layer to encapsulate a packet inside a VXLAN tunnel::
+
+ set vxlan ip-version (ipv4|ipv6) vni (vni) udp-src (udp-src) \
+ udp-dst (udp-dst) ip-src (ip-src) ip-dst (ip-dst) eth-src (eth-src) \
+ eth-dst (eth-dst)
+
+ set vxlan-with-vlan ip-version (ipv4|ipv6) vni (vni) udp-src (udp-src) \
+ udp-dst (udp-dst) ip-src (ip-src) ip-dst (ip-dst) vlan-tci (vlan-tci) \
+ eth-src (eth-src) eth-dst (eth-dst)
+
+ set vxlan-tos-ttl ip-version (ipv4|ipv6) vni (vni) udp-src (udp-src) \
+ udp-dst (udp-dst) ip-tos (ip-tos) ip-ttl (ip-ttl) ip-src (ip-src) \
+ ip-dst (ip-dst) eth-src (eth-src) eth-dst (eth-dst)
+
+These commands will set an internal configuration inside testpmd, any following
+flow rule using the action vxlan_encap will use the last configuration set.
+To have a different encapsulation header, one of those commands must be called
+before the flow rule creation.
+
+Config NVGRE Encap outer layers
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+Configure the outer layer to encapsulate a packet inside a NVGRE tunnel::
+
+ set nvgre ip-version (ipv4|ipv6) tni (tni) ip-src (ip-src) ip-dst (ip-dst) \
+ eth-src (eth-src) eth-dst (eth-dst)
+ set nvgre-with-vlan ip-version (ipv4|ipv6) tni (tni) ip-src (ip-src) \
+ ip-dst (ip-dst) vlan-tci (vlan-tci) eth-src (eth-src) eth-dst (eth-dst)
+
+These commands will set an internal configuration inside testpmd, any following
+flow rule using the action nvgre_encap will use the last configuration set.
+To have a different encapsulation header, one of those commands must be called
+before the flow rule creation.
+
+Config L2 Encap
+~~~~~~~~~~~~~~~
+
+Configure the l2 to be used when encapsulating a packet with L2::
+
+ set l2_encap ip-version (ipv4|ipv6) eth-src (eth-src) eth-dst (eth-dst)
+ set l2_encap-with-vlan ip-version (ipv4|ipv6) vlan-tci (vlan-tci) \
+ eth-src (eth-src) eth-dst (eth-dst)
+
+Those commands will set an internal configuration inside testpmd, any following
+flow rule using the action l2_encap will use the last configuration set.
+To have a different encapsulation header, one of those commands must be called
+before the flow rule creation.
+
+Config L2 Decap
+~~~~~~~~~~~~~~~
+
+Configure the l2 to be removed when decapsulating a packet with L2::
+
+ set l2_decap ip-version (ipv4|ipv6)
+ set l2_decap-with-vlan ip-version (ipv4|ipv6)
+
+Those commands will set an internal configuration inside testpmd, any following
+flow rule using the action l2_decap will use the last configuration set.
+To have a different encapsulation header, one of those commands must be called
+before the flow rule creation.
+
+Config MPLSoGRE Encap outer layers
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+Configure the outer layer to encapsulate a packet inside a MPLSoGRE tunnel::
+
+ set mplsogre_encap ip-version (ipv4|ipv6) label (label) \
+ ip-src (ip-src) ip-dst (ip-dst) eth-src (eth-src) eth-dst (eth-dst)
+ set mplsogre_encap-with-vlan ip-version (ipv4|ipv6) label (label) \
+ ip-src (ip-src) ip-dst (ip-dst) vlan-tci (vlan-tci) \
+ eth-src (eth-src) eth-dst (eth-dst)
+
+These commands will set an internal configuration inside testpmd, any following
+flow rule using the action mplsogre_encap will use the last configuration set.
+To have a different encapsulation header, one of those commands must be called
+before the flow rule creation.
+
+Config MPLSoGRE Decap outer layers
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+Configure the outer layer to decapsulate MPLSoGRE packet::
+
+ set mplsogre_decap ip-version (ipv4|ipv6)
+ set mplsogre_decap-with-vlan ip-version (ipv4|ipv6)
+
+These commands will set an internal configuration inside testpmd, any following
+flow rule using the action mplsogre_decap will use the last configuration set.
+To have a different decapsulation header, one of those commands must be called
+before the flow rule creation.
+
+Config MPLSoUDP Encap outer layers
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+Configure the outer layer to encapsulate a packet inside a MPLSoUDP tunnel::
+
+ set mplsoudp_encap ip-version (ipv4|ipv6) label (label) udp-src (udp-src) \
+ udp-dst (udp-dst) ip-src (ip-src) ip-dst (ip-dst) \
+ eth-src (eth-src) eth-dst (eth-dst)
+ set mplsoudp_encap-with-vlan ip-version (ipv4|ipv6) label (label) \
+ udp-src (udp-src) udp-dst (udp-dst) ip-src (ip-src) ip-dst (ip-dst) \
+ vlan-tci (vlan-tci) eth-src (eth-src) eth-dst (eth-dst)
+
+These commands will set an internal configuration inside testpmd, any following
+flow rule using the action mplsoudp_encap will use the last configuration set.
+To have a different encapsulation header, one of those commands must be called
+before the flow rule creation.
+
+Config MPLSoUDP Decap outer layers
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+Configure the outer layer to decapsulate MPLSoUDP packet::
+
+ set mplsoudp_decap ip-version (ipv4|ipv6)
+ set mplsoudp_decap-with-vlan ip-version (ipv4|ipv6)
+
+These commands will set an internal configuration inside testpmd, any following
+flow rule using the action mplsoudp_decap will use the last configuration set.
+To have a different decapsulation header, one of those commands must be called
+before the flow rule creation.
+
+Config Raw Encapsulation
+~~~~~~~~~~~~~~~~~~~~~~~~~
+
+Configure the raw data to be used when encapsulating a packet by
+rte_flow_action_raw_encap::
+
+ set raw_encap {index} {item} [/ {item} [...]] / end_set
+
+There are multiple global buffers for ``raw_encap``, this command will set one
+internal buffer index by ``{index}``.
+If there is no ``{index}`` specified::
+
+ set raw_encap {item} [/ {item} [...]] / end_set
+
+the default index ``0`` is used.
+In order to use different encapsulating header, ``index`` must be specified
+during the flow rule creation::
+
+ testpmd> flow create 0 egress pattern eth / ipv4 / end actions
+ raw_encap index 2 / end
+
+Otherwise the default index ``0`` is used.
+
+Config Raw Decapsulation
+~~~~~~~~~~~~~~~~~~~~~~~~
+
+Configure the raw data to be used when decapsulating a packet by
+rte_flow_action_raw_decap::
+
+ set raw_decap {index} {item} [/ {item} [...]] / end_set
+
+There are multiple global buffers for ``raw_decap``, this command will set
+one internal buffer index by ``{index}``.
+If there is no ``{index}`` specified::
+
+ set raw_decap {item} [/ {item} [...]] / end_set
+
+the default index ``0`` is used.
+In order to use different decapsulating header, ``index`` must be specified
+during the flow rule creation::
+
+ testpmd> flow create 0 egress pattern eth / ipv4 / end actions
+ raw_encap index 3 / end
+
+Otherwise the default index ``0`` is used.
+
+Port Functions
+--------------
+
+The following sections show functions for configuring ports.
+
+.. note::
+
+ Port configuration changes only become active when forwarding is started/restarted.
+
+port attach
+~~~~~~~~~~~
+
+Attach a port specified by pci address or virtual device args::
+
+ testpmd> port attach (identifier)
+
+To attach a new pci device, the device should be recognized by kernel first.
+Then it should be moved under DPDK management.
+Finally the port can be attached to testpmd.
+
+For example, to move a pci device using ixgbe under DPDK management:
+
+.. code-block:: console
+
+ # Check the status of the available devices.
+ ./usertools/dpdk-devbind.py --status
+
+ Network devices using DPDK-compatible driver
+ ============================================
+ <none>
+
+ Network devices using kernel driver
+ ===================================
+ 0000:0a:00.0 '82599ES 10-Gigabit' if=eth2 drv=ixgbe unused=
+
+
+ # Bind the device to igb_uio.
+ sudo ./usertools/dpdk-devbind.py -b igb_uio 0000:0a:00.0
+
+
+ # Recheck the status of the devices.
+ ./usertools/dpdk-devbind.py --status
+ Network devices using DPDK-compatible driver
+ ============================================
+ 0000:0a:00.0 '82599ES 10-Gigabit' drv=igb_uio unused=
+
+To attach a port created by virtual device, above steps are not needed.
+
+For example, to attach a port whose pci address is 0000:0a:00.0.
+
+.. code-block:: console
+
+ testpmd> port attach 0000:0a:00.0
+ Attaching a new port...
+ EAL: PCI device 0000:0a:00.0 on NUMA socket -1
+ EAL: probe driver: 8086:10fb rte_ixgbe_pmd
+ EAL: PCI memory mapped at 0x7f83bfa00000
+ EAL: PCI memory mapped at 0x7f83bfa80000
+ PMD: eth_ixgbe_dev_init(): MAC: 2, PHY: 18, SFP+: 5
+ PMD: eth_ixgbe_dev_init(): port 0 vendorID=0x8086 deviceID=0x10fb
+ Port 0 is attached. Now total ports is 1
+ Done
+
+For example, to attach a port created by pcap PMD.
+
+.. code-block:: console
+
+ testpmd> port attach net_pcap0
+ Attaching a new port...
+ PMD: Initializing pmd_pcap for net_pcap0
+ PMD: Creating pcap-backed ethdev on numa socket 0
+ Port 0 is attached. Now total ports is 1
+ Done
+
+In this case, identifier is ``net_pcap0``.
+This identifier format is the same as ``--vdev`` format of DPDK applications.
+
+For example, to re-attach a bonded port which has been previously detached,
+the mode and slave parameters must be given.
+
+.. code-block:: console
+
+ testpmd> port attach net_bond_0,mode=0,slave=1
+ Attaching a new port...
+ EAL: Initializing pmd_bond for net_bond_0
+ EAL: Create bonded device net_bond_0 on port 0 in mode 0 on socket 0.
+ Port 0 is attached. Now total ports is 1
+ Done
+
+
+port detach
+~~~~~~~~~~~
+
+Detach a specific port::
+
+ testpmd> port detach (port_id)
+
+Before detaching a port, the port should be stopped and closed.
+
+For example, to detach a pci device port 0.
+
+.. code-block:: console
+
+ testpmd> port stop 0
+ Stopping ports...
+ Done
+ testpmd> port close 0
+ Closing ports...
+ Done
+
+ testpmd> port detach 0
+ Detaching a port...
+ EAL: PCI device 0000:0a:00.0 on NUMA socket -1
+ EAL: remove driver: 8086:10fb rte_ixgbe_pmd
+ EAL: PCI memory unmapped at 0x7f83bfa00000
+ EAL: PCI memory unmapped at 0x7f83bfa80000
+ Done
+
+
+For example, to detach a virtual device port 0.
+
+.. code-block:: console
+
+ testpmd> port stop 0
+ Stopping ports...
+ Done
+ testpmd> port close 0
+ Closing ports...
+ Done
+
+ testpmd> port detach 0
+ Detaching a port...
+ PMD: Closing pcap ethdev on numa socket 0
+ Port 'net_pcap0' is detached. Now total ports is 0
+ Done
+
+To remove a pci device completely from the system, first detach the port from testpmd.
+Then the device should be moved under kernel management.
+Finally the device can be removed using kernel pci hotplug functionality.
+
+For example, to move a pci device under kernel management:
+
+.. code-block:: console
+
+ sudo ./usertools/dpdk-devbind.py -b ixgbe 0000:0a:00.0
+
+ ./usertools/dpdk-devbind.py --status
+
+ Network devices using DPDK-compatible driver
+ ============================================
+ <none>
+
+ Network devices using kernel driver
+ ===================================
+ 0000:0a:00.0 '82599ES 10-Gigabit' if=eth2 drv=ixgbe unused=igb_uio
+
+To remove a port created by a virtual device, above steps are not needed.
+
+port start
+~~~~~~~~~~
+
+Start all ports or a specific port::
+
+ testpmd> port start (port_id|all)
+
+port stop
+~~~~~~~~~
+
+Stop all ports or a specific port::
+
+ testpmd> port stop (port_id|all)
+
+port close
+~~~~~~~~~~
+
+Close all ports or a specific port::
+
+ testpmd> port close (port_id|all)
+
+port reset
+~~~~~~~~~~
+
+Reset all ports or a specific port::
+
+ testpmd> port reset (port_id|all)
+
+User should stop port(s) before resetting and (re-)start after reset.
+
+port config - queue ring size
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+Configure a rx/tx queue ring size::
+
+ testpmd> port (port_id) (rxq|txq) (queue_id) ring_size (value)
+
+Only take effect after command that (re-)start the port or command that setup specific queue.
+
+port start/stop queue
+~~~~~~~~~~~~~~~~~~~~~
+
+Start/stop a rx/tx queue on a specific port::
+
+ testpmd> port (port_id) (rxq|txq) (queue_id) (start|stop)
+
+port config - queue deferred start
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+Switch on/off deferred start of a specific port queue::
+
+ testpmd> port (port_id) (rxq|txq) (queue_id) deferred_start (on|off)
+
+port setup queue
+~~~~~~~~~~~~~~~~~~~~~
+
+Setup a rx/tx queue on a specific port::
+
+ testpmd> port (port_id) (rxq|txq) (queue_id) setup
+
+Only take effect when port is started.
+
+port config - speed
+~~~~~~~~~~~~~~~~~~~
+
+Set the speed and duplex mode for all ports or a specific port::
+
+ testpmd> port config (port_id|all) speed (10|100|1000|10000|25000|40000|50000|100000|auto) \
+ duplex (half|full|auto)
+
+port config - queues/descriptors
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+Set number of queues/descriptors for rxq, txq, rxd and txd::
+
+ testpmd> port config all (rxq|txq|rxd|txd) (value)
+
+This is equivalent to the ``--rxq``, ``--txq``, ``--rxd`` and ``--txd`` command-line options.
+
+port config - max-pkt-len
+~~~~~~~~~~~~~~~~~~~~~~~~~
+
+Set the maximum packet length::
+
+ testpmd> port config all max-pkt-len (value)
+
+This is equivalent to the ``--max-pkt-len`` command-line option.
+
+port config - max-lro-pkt-size
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+Set the maximum LRO aggregated packet size::
+
+ testpmd> port config all max-lro-pkt-size (value)
+
+This is equivalent to the ``--max-lro-pkt-size`` command-line option.
+
+port config - Drop Packets
+~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+Enable or disable packet drop on all RX queues of all ports when no receive buffers available::
+
+ testpmd> port config all drop-en (on|off)
+
+Packet dropping when no receive buffers available is off by default.
+
+The ``on`` option is equivalent to the ``--enable-drop-en`` command-line option.
+
+port config - RSS
+~~~~~~~~~~~~~~~~~
+
+Set the RSS (Receive Side Scaling) mode on or off::
+
+ testpmd> port config all rss (all|default|ip|tcp|udp|sctp|ether|port|vxlan|geneve|nvgre|vxlan-gpe|none)
+
+RSS is on by default.
+
+The ``all`` option is equivalent to ip|tcp|udp|sctp|ether.
+The ``default`` option enables all supported RSS types reported by device info.
+The ``none`` option is equivalent to the ``--disable-rss`` command-line option.
+
+port config - RSS Reta
+~~~~~~~~~~~~~~~~~~~~~~
+
+Set the RSS (Receive Side Scaling) redirection table::
+
+ testpmd> port config all rss reta (hash,queue)[,(hash,queue)]
+
+port config - DCB
+~~~~~~~~~~~~~~~~~
+
+Set the DCB mode for an individual port::
+
+ testpmd> port config (port_id) dcb vt (on|off) (traffic_class) pfc (on|off)
+
+The traffic class should be 4 or 8.
+
+port config - Burst
+~~~~~~~~~~~~~~~~~~~
+
+Set the number of packets per burst::
+
+ testpmd> port config all burst (value)
+
+This is equivalent to the ``--burst`` command-line option.
+
+port config - Threshold
+~~~~~~~~~~~~~~~~~~~~~~~
+
+Set thresholds for TX/RX queues::
+
+ testpmd> port config all (threshold) (value)
+
+Where the threshold type can be:
+
+* ``txpt:`` Set the prefetch threshold register of the TX rings, 0 <= value <= 255.
+
+* ``txht:`` Set the host threshold register of the TX rings, 0 <= value <= 255.
+
+* ``txwt:`` Set the write-back threshold register of the TX rings, 0 <= value <= 255.
+
+* ``rxpt:`` Set the prefetch threshold register of the RX rings, 0 <= value <= 255.
+
+* ``rxht:`` Set the host threshold register of the RX rings, 0 <= value <= 255.
+
+* ``rxwt:`` Set the write-back threshold register of the RX rings, 0 <= value <= 255.
+
+* ``txfreet:`` Set the transmit free threshold of the TX rings, 0 <= value <= txd.
+
+* ``rxfreet:`` Set the transmit free threshold of the RX rings, 0 <= value <= rxd.
+
+* ``txrst:`` Set the transmit RS bit threshold of TX rings, 0 <= value <= txd.
+
+These threshold options are also available from the command-line.
+
+port config - E-tag
+~~~~~~~~~~~~~~~~~~~
+
+Set the value of ether-type for E-tag::
+
+ testpmd> port config (port_id|all) l2-tunnel E-tag ether-type (value)
+
+Enable/disable the E-tag support::
+
+ testpmd> port config (port_id|all) l2-tunnel E-tag (enable|disable)
+
+port config pctype mapping
+~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+Reset pctype mapping table::
+
+ testpmd> port config (port_id) pctype mapping reset
+
+Update hardware defined pctype to software defined flow type mapping table::
+
+ testpmd> port config (port_id) pctype mapping update (pctype_id_0[,pctype_id_1]*) (flow_type_id)
+
+where:
+
+* ``pctype_id_x``: hardware pctype id as index of bit in bitmask value of the pctype mapping table.
+
+* ``flow_type_id``: software flow type id as the index of the pctype mapping table.
+
+port config input set
+~~~~~~~~~~~~~~~~~~~~~
+
+Config RSS/FDIR/FDIR flexible payload input set for some pctype::
+
+ testpmd> port config (port_id) pctype (pctype_id) \
+ (hash_inset|fdir_inset|fdir_flx_inset) \
+ (get|set|clear) field (field_idx)
+
+Clear RSS/FDIR/FDIR flexible payload input set for some pctype::
+
+ testpmd> port config (port_id) pctype (pctype_id) \
+ (hash_inset|fdir_inset|fdir_flx_inset) clear all
+
+where:
+
+* ``pctype_id``: hardware packet classification types.
+* ``field_idx``: hardware field index.
+
+port config udp_tunnel_port
+~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+Add/remove UDP tunnel port for VXLAN/GENEVE tunneling protocols::
+
+ testpmd> port config (port_id) udp_tunnel_port add|rm vxlan|geneve|vxlan-gpe (udp_port)
+
+port config tx_metadata
+~~~~~~~~~~~~~~~~~~~~~~~
+
+Set Tx metadata value per port.
+testpmd will add this value to any Tx packet sent from this port::
+
+ testpmd> port config (port_id) tx_metadata (value)
+
+port config dynf
+~~~~~~~~~~~~~~~~
+
+Set/clear dynamic flag per port.
+testpmd will register this flag in the mbuf (same registration
+for both Tx and Rx). Then set/clear this flag for each Tx
+packet sent from this port. The set bit only works for Tx packet::
+
+ testpmd> port config (port_id) dynf (name) (set|clear)
+
+port config mtu
+~~~~~~~~~~~~~~~
+
+To configure MTU(Maximum Transmission Unit) on devices using testpmd::
+
+ testpmd> port config mtu (port_id) (value)
+
+port config rss hash key
+~~~~~~~~~~~~~~~~~~~~~~~~
+
+To configure the RSS hash key used to compute the RSS
+hash of input [IP] packets received on port::
+
+ testpmd> port config <port_id> rss-hash-key (ipv4|ipv4-frag|\
+ ipv4-tcp|ipv4-udp|ipv4-sctp|ipv4-other|\
+ ipv6|ipv6-frag|ipv6-tcp|ipv6-udp|ipv6-sctp|\
+ ipv6-other|l2-payload|ipv6-ex|ipv6-tcp-ex|\
+ ipv6-udp-ex <string of hex digits \
+ (variable length, NIC dependent)>)
+
+Device Functions
+----------------
+
+The following sections show functions for device operations.
+
+device detach
+~~~~~~~~~~~~~
+
+Detach a device specified by pci address or virtual device args::
+
+ testpmd> device detach (identifier)
+
+Before detaching a device associated with ports, the ports should be stopped and closed.
+
+For example, to detach a pci device whose address is 0002:03:00.0.
+
+.. code-block:: console
+
+ testpmd> device detach 0002:03:00.0
+ Removing a device...
+ Port 1 is now closed
+ EAL: Releasing pci mapped resource for 0002:03:00.0
+ EAL: Calling pci_unmap_resource for 0002:03:00.0 at 0x218a050000
+ EAL: Calling pci_unmap_resource for 0002:03:00.0 at 0x218c050000
+ Device 0002:03:00.0 is detached
+ Now total ports is 1
+
+For example, to detach a port created by pcap PMD.
+
+.. code-block:: console
+
+ testpmd> device detach net_pcap0
+ Removing a device...
+ Port 0 is now closed
+ Device net_pcap0 is detached
+ Now total ports is 0
+ Done
+
+In this case, identifier is ``net_pcap0``.
+This identifier format is the same as ``--vdev`` format of DPDK applications.
+
+Link Bonding Functions
+----------------------
+
+The Link Bonding functions make it possible to dynamically create and
+manage link bonding devices from within testpmd interactive prompt.
+
+create bonded device
+~~~~~~~~~~~~~~~~~~~~
+
+Create a new bonding device::
+
+ testpmd> create bonded device (mode) (socket)
+
+For example, to create a bonded device in mode 1 on socket 0::
+
+ testpmd> create bonded device 1 0
+ created new bonded device (port X)
+
+add bonding slave
+~~~~~~~~~~~~~~~~~
+
+Adds Ethernet device to a Link Bonding device::
+
+ testpmd> add bonding slave (slave id) (port id)
+
+For example, to add Ethernet device (port 6) to a Link Bonding device (port 10)::
+
+ testpmd> add bonding slave 6 10
+
+
+remove bonding slave
+~~~~~~~~~~~~~~~~~~~~
+
+Removes an Ethernet slave device from a Link Bonding device::
+
+ testpmd> remove bonding slave (slave id) (port id)
+
+For example, to remove Ethernet slave device (port 6) to a Link Bonding device (port 10)::
+
+ testpmd> remove bonding slave 6 10
+
+set bonding mode
+~~~~~~~~~~~~~~~~
+
+Set the Link Bonding mode of a Link Bonding device::
+
+ testpmd> set bonding mode (value) (port id)
+
+For example, to set the bonding mode of a Link Bonding device (port 10) to broadcast (mode 3)::
+
+ testpmd> set bonding mode 3 10
+
+set bonding primary
+~~~~~~~~~~~~~~~~~~~
+
+Set an Ethernet slave device as the primary device on a Link Bonding device::
+
+ testpmd> set bonding primary (slave id) (port id)
+
+For example, to set the Ethernet slave device (port 6) as the primary port of a Link Bonding device (port 10)::
+
+ testpmd> set bonding primary 6 10
+
+set bonding mac
+~~~~~~~~~~~~~~~
+
+Set the MAC address of a Link Bonding device::
+
+ testpmd> set bonding mac (port id) (mac)
+
+For example, to set the MAC address of a Link Bonding device (port 10) to 00:00:00:00:00:01::
+
+ testpmd> set bonding mac 10 00:00:00:00:00:01
+
+set bonding xmit_balance_policy
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+Set the transmission policy for a Link Bonding device when it is in Balance XOR mode::
+
+ testpmd> set bonding xmit_balance_policy (port_id) (l2|l23|l34)
+
+For example, set a Link Bonding device (port 10) to use a balance policy of layer 3+4 (IP addresses & UDP ports)::
+
+ testpmd> set bonding xmit_balance_policy 10 l34
+
+
+set bonding mon_period
+~~~~~~~~~~~~~~~~~~~~~~
+
+Set the link status monitoring polling period in milliseconds for a bonding device.
+
+This adds support for PMD slave devices which do not support link status interrupts.
+When the mon_period is set to a value greater than 0 then all PMD's which do not support
+link status ISR will be queried every polling interval to check if their link status has changed::
+
+ testpmd> set bonding mon_period (port_id) (value)
+
+For example, to set the link status monitoring polling period of bonded device (port 5) to 150ms::
+
+ testpmd> set bonding mon_period 5 150
+
+
+set bonding lacp dedicated_queue
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+Enable dedicated tx/rx queues on bonding devices slaves to handle LACP control plane traffic
+when in mode 4 (link-aggregation-802.3ad)::
+
+ testpmd> set bonding lacp dedicated_queues (port_id) (enable|disable)
+
+
+set bonding agg_mode
+~~~~~~~~~~~~~~~~~~~~
+
+Enable one of the specific aggregators mode when in mode 4 (link-aggregation-802.3ad)::
+
+ testpmd> set bonding agg_mode (port_id) (bandwidth|count|stable)
+
+
+show bonding config
+~~~~~~~~~~~~~~~~~~~
+
+Show the current configuration of a Link Bonding device::
+
+ testpmd> show bonding config (port id)
+
+For example,
+to show the configuration a Link Bonding device (port 9) with 3 slave devices (1, 3, 4)
+in balance mode with a transmission policy of layer 2+3::
+
+ testpmd> show bonding config 9
+ Bonding mode: 2
+ Balance Xmit Policy: BALANCE_XMIT_POLICY_LAYER23
+ Slaves (3): [1 3 4]
+ Active Slaves (3): [1 3 4]
+ Primary: [3]
+
+
+Register Functions
+------------------
+
+The Register Functions can be used to read from and write to registers on the network card referenced by a port number.
+This is mainly useful for debugging purposes.
+Reference should be made to the appropriate datasheet for the network card for details on the register addresses
+and fields that can be accessed.
+
+read reg
+~~~~~~~~
+
+Display the value of a port register::
+
+ testpmd> read reg (port_id) (address)
+
+For example, to examine the Flow Director control register (FDIRCTL, 0x0000EE000) on an Intel 82599 10 GbE Controller::
+
+ testpmd> read reg 0 0xEE00
+ port 0 PCI register at offset 0xEE00: 0x4A060029 (1241907241)
+
+read regfield
+~~~~~~~~~~~~~
+
+Display a port register bit field::
+
+ testpmd> read regfield (port_id) (address) (bit_x) (bit_y)
+
+For example, reading the lowest two bits from the register in the example above::
+
+ testpmd> read regfield 0 0xEE00 0 1
+ port 0 PCI register at offset 0xEE00: bits[0, 1]=0x1 (1)
+
+read regbit
+~~~~~~~~~~~
+
+Display a single port register bit::
+
+ testpmd> read regbit (port_id) (address) (bit_x)
+
+For example, reading the lowest bit from the register in the example above::
+
+ testpmd> read regbit 0 0xEE00 0
+ port 0 PCI register at offset 0xEE00: bit 0=1
+
+write reg
+~~~~~~~~~
+
+Set the value of a port register::
+
+ testpmd> write reg (port_id) (address) (value)
+
+For example, to clear a register::
+
+ testpmd> write reg 0 0xEE00 0x0
+ port 0 PCI register at offset 0xEE00: 0x00000000 (0)
+
+write regfield
+~~~~~~~~~~~~~~
+
+Set bit field of a port register::
+
+ testpmd> write regfield (port_id) (address) (bit_x) (bit_y) (value)
+
+For example, writing to the register cleared in the example above::
+
+ testpmd> write regfield 0 0xEE00 0 1 2
+ port 0 PCI register at offset 0xEE00: 0x00000002 (2)
+
+write regbit
+~~~~~~~~~~~~
+
+Set single bit value of a port register::
+
+ testpmd> write regbit (port_id) (address) (bit_x) (value)
+
+For example, to set the high bit in the register from the example above::
+
+ testpmd> write regbit 0 0xEE00 31 1
+ port 0 PCI register at offset 0xEE00: 0x8000000A (2147483658)
+
+Traffic Metering and Policing
+-----------------------------
+
+The following section shows functions for configuring traffic metering and
+policing on the ethernet device through the use of generic ethdev API.
+
+show port traffic management capability
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+Show traffic metering and policing capability of the port::
+
+ testpmd> show port meter cap (port_id)
+
+add port meter profile (srTCM rfc2967)
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+Add meter profile (srTCM rfc2697) to the ethernet device::
+
+ testpmd> add port meter profile srtcm_rfc2697 (port_id) (profile_id) \
+ (cir) (cbs) (ebs)
+
+where:
+
+* ``profile_id``: ID for the meter profile.
+* ``cir``: Committed Information Rate (CIR) (bytes/second).
+* ``cbs``: Committed Burst Size (CBS) (bytes).
+* ``ebs``: Excess Burst Size (EBS) (bytes).
+
+add port meter profile (trTCM rfc2968)
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+Add meter profile (srTCM rfc2698) to the ethernet device::
+
+ testpmd> add port meter profile trtcm_rfc2698 (port_id) (profile_id) \
+ (cir) (pir) (cbs) (pbs)
+
+where:
+
+* ``profile_id``: ID for the meter profile.
+* ``cir``: Committed information rate (bytes/second).
+* ``pir``: Peak information rate (bytes/second).
+* ``cbs``: Committed burst size (bytes).
+* ``pbs``: Peak burst size (bytes).
+
+add port meter profile (trTCM rfc4115)
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+Add meter profile (trTCM rfc4115) to the ethernet device::
+
+ testpmd> add port meter profile trtcm_rfc4115 (port_id) (profile_id) \
+ (cir) (eir) (cbs) (ebs)
+
+where:
+
+* ``profile_id``: ID for the meter profile.
+* ``cir``: Committed information rate (bytes/second).
+* ``eir``: Excess information rate (bytes/second).
+* ``cbs``: Committed burst size (bytes).
+* ``ebs``: Excess burst size (bytes).
+
+delete port meter profile
+~~~~~~~~~~~~~~~~~~~~~~~~~
+
+Delete meter profile from the ethernet device::
+
+ testpmd> del port meter profile (port_id) (profile_id)
+
+create port meter
+~~~~~~~~~~~~~~~~~
+
+Create new meter object for the ethernet device::
+
+ testpmd> create port meter (port_id) (mtr_id) (profile_id) \
+ (meter_enable) (g_action) (y_action) (r_action) (stats_mask) (shared) \
+ (use_pre_meter_color) [(dscp_tbl_entry0) (dscp_tbl_entry1)...\
+ (dscp_tbl_entry63)]
+
+where:
+
+* ``mtr_id``: meter object ID.
+* ``profile_id``: ID for the meter profile.
+* ``meter_enable``: When this parameter has a non-zero value, the meter object
+ gets enabled at the time of creation, otherwise remains disabled.
+* ``g_action``: Policer action for the packet with green color.
+* ``y_action``: Policer action for the packet with yellow color.
+* ``r_action``: Policer action for the packet with red color.
+* ``stats_mask``: Mask of statistics counter types to be enabled for the
+ meter object.
+* ``shared``: When this parameter has a non-zero value, the meter object is
+ shared by multiple flows. Otherwise, meter object is used by single flow.
+* ``use_pre_meter_color``: When this parameter has a non-zero value, the
+ input color for the current meter object is determined by the latest meter
+ object in the same flow. Otherwise, the current meter object uses the
+ *dscp_table* to determine the input color.
+* ``dscp_tbl_entryx``: DSCP table entry x providing meter providing input
+ color, 0 <= x <= 63.
+
+enable port meter
+~~~~~~~~~~~~~~~~~
+
+Enable meter for the ethernet device::
+
+ testpmd> enable port meter (port_id) (mtr_id)
+
+disable port meter
+~~~~~~~~~~~~~~~~~~
+
+Disable meter for the ethernet device::
+
+ testpmd> disable port meter (port_id) (mtr_id)
+
+delete port meter
+~~~~~~~~~~~~~~~~~
+
+Delete meter for the ethernet device::
+
+ testpmd> del port meter (port_id) (mtr_id)
+
+Set port meter profile
+~~~~~~~~~~~~~~~~~~~~~~
+
+Set meter profile for the ethernet device::
+
+ testpmd> set port meter profile (port_id) (mtr_id) (profile_id)
+
+set port meter dscp table
+~~~~~~~~~~~~~~~~~~~~~~~~~
+
+Set meter dscp table for the ethernet device::
+
+ testpmd> set port meter dscp table (port_id) (mtr_id) [(dscp_tbl_entry0) \
+ (dscp_tbl_entry1)...(dscp_tbl_entry63)]
+
+set port meter policer action
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+Set meter policer action for the ethernet device::
+
+ testpmd> set port meter policer action (port_id) (mtr_id) (action_mask) \
+ (action0) [(action1) (action1)]
+
+where:
+
+* ``action_mask``: Bit mask indicating which policer actions need to be
+ updated. One or more policer actions can be updated in a single function
+ invocation. To update the policer action associated with color C, bit
+ (1 << C) needs to be set in *action_mask* and element at position C
+ in the *actions* array needs to be valid.
+* ``actionx``: Policer action for the color x,
+ RTE_MTR_GREEN <= x < RTE_MTR_COLORS
+
+set port meter stats mask
+~~~~~~~~~~~~~~~~~~~~~~~~~
+
+Set meter stats mask for the ethernet device::
+
+ testpmd> set port meter stats mask (port_id) (mtr_id) (stats_mask)
+
+where:
+
+* ``stats_mask``: Bit mask indicating statistics counter types to be enabled.
+
+show port meter stats
+~~~~~~~~~~~~~~~~~~~~~
+
+Show meter stats of the ethernet device::
+
+ testpmd> show port meter stats (port_id) (mtr_id) (clear)
+
+where:
+
+* ``clear``: Flag that indicates whether the statistics counters should
+ be cleared (i.e. set to zero) immediately after they have been read or not.
+
+Traffic Management
+------------------
+
+The following section shows functions for configuring traffic management on
+the ethernet device through the use of generic TM API.
+
+show port traffic management capability
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+Show traffic management capability of the port::
+
+ testpmd> show port tm cap (port_id)
+
+show port traffic management capability (hierarchy level)
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+Show traffic management hierarchy level capability of the port::
+
+ testpmd> show port tm level cap (port_id) (level_id)
+
+show port traffic management capability (hierarchy node level)
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+Show the traffic management hierarchy node capability of the port::
+
+ testpmd> show port tm node cap (port_id) (node_id)
+
+show port traffic management hierarchy node type
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+Show the port traffic management hierarchy node type::
+
+ testpmd> show port tm node type (port_id) (node_id)
+
+show port traffic management hierarchy node stats
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+Show the port traffic management hierarchy node statistics::
+
+ testpmd> show port tm node stats (port_id) (node_id) (clear)
+
+where:
+
+* ``clear``: When this parameter has a non-zero value, the statistics counters
+ are cleared (i.e. set to zero) immediately after they have been read,
+ otherwise the statistics counters are left untouched.
+
+Add port traffic management private shaper profile
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+Add the port traffic management private shaper profile::
+
+ testpmd> add port tm node shaper profile (port_id) (shaper_profile_id) \
+ (cmit_tb_rate) (cmit_tb_size) (peak_tb_rate) (peak_tb_size) \
+ (packet_length_adjust)
+
+where:
+
+* ``shaper_profile id``: Shaper profile ID for the new profile.
+* ``cmit_tb_rate``: Committed token bucket rate (bytes per second).
+* ``cmit_tb_size``: Committed token bucket size (bytes).
+* ``peak_tb_rate``: Peak token bucket rate (bytes per second).
+* ``peak_tb_size``: Peak token bucket size (bytes).
+* ``packet_length_adjust``: The value (bytes) to be added to the length of
+ each packet for the purpose of shaping. This parameter value can be used to
+ correct the packet length with the framing overhead bytes that are consumed
+ on the wire.
+
+Delete port traffic management private shaper profile
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+Delete the port traffic management private shaper::
+
+ testpmd> del port tm node shaper profile (port_id) (shaper_profile_id)
+
+where:
+
+* ``shaper_profile id``: Shaper profile ID that needs to be deleted.
+
+Add port traffic management shared shaper
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+Create the port traffic management shared shaper::
+
+ testpmd> add port tm node shared shaper (port_id) (shared_shaper_id) \
+ (shaper_profile_id)
+
+where:
+
+* ``shared_shaper_id``: Shared shaper ID to be created.
+* ``shaper_profile id``: Shaper profile ID for shared shaper.
+
+Set port traffic management shared shaper
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+Update the port traffic management shared shaper::
+
+ testpmd> set port tm node shared shaper (port_id) (shared_shaper_id) \
+ (shaper_profile_id)
+
+where:
+
+* ``shared_shaper_id``: Shared shaper ID to be update.
+* ``shaper_profile id``: Shaper profile ID for shared shaper.
+
+Delete port traffic management shared shaper
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+Delete the port traffic management shared shaper::
+
+ testpmd> del port tm node shared shaper (port_id) (shared_shaper_id)
+
+where:
+
+* ``shared_shaper_id``: Shared shaper ID to be deleted.
+
+Set port traffic management hierarchy node private shaper
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+set the port traffic management hierarchy node private shaper::
+
+ testpmd> set port tm node shaper profile (port_id) (node_id) \
+ (shaper_profile_id)
+
+where:
+
+* ``shaper_profile id``: Private shaper profile ID to be enabled on the
+ hierarchy node.
+
+Add port traffic management WRED profile
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+Create a new WRED profile::
+
+ testpmd> add port tm node wred profile (port_id) (wred_profile_id) \
+ (color_g) (min_th_g) (max_th_g) (maxp_inv_g) (wq_log2_g) \
+ (color_y) (min_th_y) (max_th_y) (maxp_inv_y) (wq_log2_y) \
+ (color_r) (min_th_r) (max_th_r) (maxp_inv_r) (wq_log2_r)
+
+where:
+
+* ``wred_profile id``: Identifier for the newly create WRED profile
+* ``color_g``: Packet color (green)
+* ``min_th_g``: Minimum queue threshold for packet with green color
+* ``max_th_g``: Minimum queue threshold for packet with green color
+* ``maxp_inv_g``: Inverse of packet marking probability maximum value (maxp)
+* ``wq_log2_g``: Negated log2 of queue weight (wq)
+* ``color_y``: Packet color (yellow)
+* ``min_th_y``: Minimum queue threshold for packet with yellow color
+* ``max_th_y``: Minimum queue threshold for packet with yellow color
+* ``maxp_inv_y``: Inverse of packet marking probability maximum value (maxp)
+* ``wq_log2_y``: Negated log2 of queue weight (wq)
+* ``color_r``: Packet color (red)
+* ``min_th_r``: Minimum queue threshold for packet with yellow color
+* ``max_th_r``: Minimum queue threshold for packet with yellow color
+* ``maxp_inv_r``: Inverse of packet marking probability maximum value (maxp)
+* ``wq_log2_r``: Negated log2 of queue weight (wq)
+
+Delete port traffic management WRED profile
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+Delete the WRED profile::
+
+ testpmd> del port tm node wred profile (port_id) (wred_profile_id)
+
+Add port traffic management hierarchy nonleaf node
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+Add nonleaf node to port traffic management hierarchy::
+
+ testpmd> add port tm nonleaf node (port_id) (node_id) (parent_node_id) \
+ (priority) (weight) (level_id) (shaper_profile_id) \
+ (n_sp_priorities) (stats_mask) (n_shared_shapers) \
+ [(shared_shaper_0) (shared_shaper_1) ...] \
+
+where:
+
+* ``parent_node_id``: Node ID of the parent.
+* ``priority``: Node priority (highest node priority is zero). This is used by
+ the SP algorithm running on the parent node for scheduling this node.
+* ``weight``: Node weight (lowest weight is one). The node weight is relative
+ to the weight sum of all siblings that have the same priority. It is used by
+ the WFQ algorithm running on the parent node for scheduling this node.
+* ``level_id``: Hierarchy level of the node.
+* ``shaper_profile_id``: Shaper profile ID of the private shaper to be used by
+ the node.
+* ``n_sp_priorities``: Number of strict priorities.
+* ``stats_mask``: Mask of statistics counter types to be enabled for this node.
+* ``n_shared_shapers``: Number of shared shapers.
+* ``shared_shaper_id``: Shared shaper id.
+
+Add port traffic management hierarchy leaf node
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+Add leaf node to port traffic management hierarchy::
+
+ testpmd> add port tm leaf node (port_id) (node_id) (parent_node_id) \
+ (priority) (weight) (level_id) (shaper_profile_id) \
+ (cman_mode) (wred_profile_id) (stats_mask) (n_shared_shapers) \
+ [(shared_shaper_id) (shared_shaper_id) ...] \
+
+where:
+
+* ``parent_node_id``: Node ID of the parent.
+* ``priority``: Node priority (highest node priority is zero). This is used by
+ the SP algorithm running on the parent node for scheduling this node.
+* ``weight``: Node weight (lowest weight is one). The node weight is relative
+ to the weight sum of all siblings that have the same priority. It is used by
+ the WFQ algorithm running on the parent node for scheduling this node.
+* ``level_id``: Hierarchy level of the node.
+* ``shaper_profile_id``: Shaper profile ID of the private shaper to be used by
+ the node.
+* ``cman_mode``: Congestion management mode to be enabled for this node.
+* ``wred_profile_id``: WRED profile id to be enabled for this node.
+* ``stats_mask``: Mask of statistics counter types to be enabled for this node.
+* ``n_shared_shapers``: Number of shared shapers.
+* ``shared_shaper_id``: Shared shaper id.
+
+Delete port traffic management hierarchy node
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+Delete node from port traffic management hierarchy::
+
+ testpmd> del port tm node (port_id) (node_id)
+
+Update port traffic management hierarchy parent node
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+Update port traffic management hierarchy parent node::
+
+ testpmd> set port tm node parent (port_id) (node_id) (parent_node_id) \
+ (priority) (weight)
+
+This function can only be called after the hierarchy commit invocation. Its
+success depends on the port support for this operation, as advertised through
+the port capability set. This function is valid for all nodes of the traffic
+management hierarchy except root node.
+
+Suspend port traffic management hierarchy node
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+ testpmd> suspend port tm node (port_id) (node_id)
+
+Resume port traffic management hierarchy node
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+ testpmd> resume port tm node (port_id) (node_id)
+
+Commit port traffic management hierarchy
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+Commit the traffic management hierarchy on the port::
+
+ testpmd> port tm hierarchy commit (port_id) (clean_on_fail)
+
+where:
+
+* ``clean_on_fail``: When set to non-zero, hierarchy is cleared on function
+ call failure. On the other hand, hierarchy is preserved when this parameter
+ is equal to zero.
+
+Set port traffic management mark VLAN dei
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+Enables/Disables the traffic management marking on the port for VLAN packets::
+
+ testpmd> set port tm mark vlan_dei <port_id> <green> <yellow> <red>
+
+where:
+
+* ``port_id``: The port which on which VLAN packets marked as ``green`` or
+ ``yellow`` or ``red`` will have dei bit enabled
+
+* ``green`` enable 1, disable 0 marking for dei bit of VLAN packets marked as green
+
+* ``yellow`` enable 1, disable 0 marking for dei bit of VLAN packets marked as yellow
+
+* ``red`` enable 1, disable 0 marking for dei bit of VLAN packets marked as red
+
+Set port traffic management mark IP dscp
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+Enables/Disables the traffic management marking on the port for IP dscp packets::
+
+ testpmd> set port tm mark ip_dscp <port_id> <green> <yellow> <red>
+
+where:
+
+* ``port_id``: The port which on which IP packets marked as ``green`` or
+ ``yellow`` or ``red`` will have IP dscp bits updated
+
+* ``green`` enable 1, disable 0 marking IP dscp to low drop precedence for green packets
+
+* ``yellow`` enable 1, disable 0 marking IP dscp to medium drop precedence for yellow packets
+
+* ``red`` enable 1, disable 0 marking IP dscp to high drop precedence for red packets
+
+Set port traffic management mark IP ecn
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+Enables/Disables the traffic management marking on the port for IP ecn packets::
+
+ testpmd> set port tm mark ip_ecn <port_id> <green> <yellow> <red>
+
+where:
+
+* ``port_id``: The port which on which IP packets marked as ``green`` or
+ ``yellow`` or ``red`` will have IP ecn bits updated
+
+* ``green`` enable 1, disable 0 marking IP ecn for green marked packets with ecn of 2'b01 or 2'b10
+ to ecn of 2'b11 when IP is caring TCP or SCTP
+
+* ``yellow`` enable 1, disable 0 marking IP ecn for yellow marked packets with ecn of 2'b01 or 2'b10
+ to ecn of 2'b11 when IP is caring TCP or SCTP
+
+* ``red`` enable 1, disable 0 marking IP ecn for yellow marked packets with ecn of 2'b01 or 2'b10
+ to ecn of 2'b11 when IP is caring TCP or SCTP
+
+Set port traffic management default hierarchy (softnic forwarding mode)
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+set the traffic management default hierarchy on the port::
+
+ testpmd> set port tm hierarchy default (port_id)
+
+Filter Functions
+----------------
+
+This section details the available filter functions that are available.
+
+Note these functions interface the deprecated legacy filtering framework,
+superseded by *rte_flow*. See `Flow rules management`_.
+
+ethertype_filter
+~~~~~~~~~~~~~~~~~~~~
+
+Add or delete a L2 Ethertype filter, which identify packets by their L2 Ethertype mainly assign them to a receive queue::
+
+ ethertype_filter (port_id) (add|del) (mac_addr|mac_ignr) (mac_address) \
+ ethertype (ether_type) (drop|fwd) queue (queue_id)
+
+The available information parameters are:
+
+* ``port_id``: The port which the Ethertype filter assigned on.
+
+* ``mac_addr``: Compare destination mac address.
+
+* ``mac_ignr``: Ignore destination mac address match.
+
+* ``mac_address``: Destination mac address to match.
+
+* ``ether_type``: The EtherType value want to match,
+ for example 0x0806 for ARP packet. 0x0800 (IPv4) and 0x86DD (IPv6) are invalid.
+
+* ``queue_id``: The receive queue associated with this EtherType filter.
+ It is meaningless when deleting or dropping.
+
+Example, to add/remove an ethertype filter rule::
+
+ testpmd> ethertype_filter 0 add mac_ignr 00:11:22:33:44:55 \
+ ethertype 0x0806 fwd queue 3
+
+ testpmd> ethertype_filter 0 del mac_ignr 00:11:22:33:44:55 \
+ ethertype 0x0806 fwd queue 3
+
+2tuple_filter
+~~~~~~~~~~~~~~~~~
+
+Add or delete a 2-tuple filter,
+which identifies packets by specific protocol and destination TCP/UDP port
+and forwards packets into one of the receive queues::
+
+ 2tuple_filter (port_id) (add|del) dst_port (dst_port_value) \
+ protocol (protocol_value) mask (mask_value) \
+ tcp_flags (tcp_flags_value) priority (prio_value) \
+ queue (queue_id)
+
+The available information parameters are:
+
+* ``port_id``: The port which the 2-tuple filter assigned on.
+
+* ``dst_port_value``: Destination port in L4.
+
+* ``protocol_value``: IP L4 protocol.
+
+* ``mask_value``: Participates in the match or not by bit for field above, 1b means participate.
+
+* ``tcp_flags_value``: TCP control bits. The non-zero value is invalid, when the pro_value is not set to 0x06 (TCP).
+
+* ``prio_value``: Priority of this filter.
+
+* ``queue_id``: The receive queue associated with this 2-tuple filter.
+
+Example, to add/remove an 2tuple filter rule::
+
+ testpmd> 2tuple_filter 0 add dst_port 32 protocol 0x06 mask 0x03 \
+ tcp_flags 0x02 priority 3 queue 3
+
+ testpmd> 2tuple_filter 0 del dst_port 32 protocol 0x06 mask 0x03 \
+ tcp_flags 0x02 priority 3 queue 3
+
+5tuple_filter
+~~~~~~~~~~~~~~~~~
+
+Add or delete a 5-tuple filter,
+which consists of a 5-tuple (protocol, source and destination IP addresses, source and destination TCP/UDP/SCTP port)
+and routes packets into one of the receive queues::
+
+ 5tuple_filter (port_id) (add|del) dst_ip (dst_address) src_ip \
+ (src_address) dst_port (dst_port_value) \
+ src_port (src_port_value) protocol (protocol_value) \
+ mask (mask_value) tcp_flags (tcp_flags_value) \
+ priority (prio_value) queue (queue_id)
+
+The available information parameters are:
+
+* ``port_id``: The port which the 5-tuple filter assigned on.
+
+* ``dst_address``: Destination IP address.
+
+* ``src_address``: Source IP address.
+
+* ``dst_port_value``: TCP/UDP destination port.
+
+* ``src_port_value``: TCP/UDP source port.
+
+* ``protocol_value``: L4 protocol.
+
+* ``mask_value``: Participates in the match or not by bit for field above, 1b means participate
+
+* ``tcp_flags_value``: TCP control bits. The non-zero value is invalid, when the protocol_value is not set to 0x06 (TCP).
+
+* ``prio_value``: The priority of this filter.
+
+* ``queue_id``: The receive queue associated with this 5-tuple filter.
+
+Example, to add/remove an 5tuple filter rule::
+
+ testpmd> 5tuple_filter 0 add dst_ip 2.2.2.5 src_ip 2.2.2.4 \
+ dst_port 64 src_port 32 protocol 0x06 mask 0x1F \
+ flags 0x0 priority 3 queue 3
+
+ testpmd> 5tuple_filter 0 del dst_ip 2.2.2.5 src_ip 2.2.2.4 \
+ dst_port 64 src_port 32 protocol 0x06 mask 0x1F \
+ flags 0x0 priority 3 queue 3
+
+syn_filter
+~~~~~~~~~~
+
+Using the SYN filter, TCP packets whose *SYN* flag is set can be forwarded to a separate queue::
+
+ syn_filter (port_id) (add|del) priority (high|low) queue (queue_id)
+
+The available information parameters are:
+
+* ``port_id``: The port which the SYN filter assigned on.
+
+* ``high``: This SYN filter has higher priority than other filters.
+
+* ``low``: This SYN filter has lower priority than other filters.
+
+* ``queue_id``: The receive queue associated with this SYN filter
+
+Example::
+
+ testpmd> syn_filter 0 add priority high queue 3
+
+flex_filter
+~~~~~~~~~~~
+
+With flex filter, packets can be recognized by any arbitrary pattern within the first 128 bytes of the packet
+and routed into one of the receive queues::
+
+ flex_filter (port_id) (add|del) len (len_value) bytes (bytes_value) \
+ mask (mask_value) priority (prio_value) queue (queue_id)
+
+The available information parameters are:
+
+* ``port_id``: The port which the Flex filter is assigned on.
+
+* ``len_value``: Filter length in bytes, no greater than 128.
+
+* ``bytes_value``: A string in hexadecimal, means the value the flex filter needs to match.
+
+* ``mask_value``: A string in hexadecimal, bit 1 means corresponding byte participates in the match.
+
+* ``prio_value``: The priority of this filter.
+
+* ``queue_id``: The receive queue associated with this Flex filter.
+
+Example::
+
+ testpmd> flex_filter 0 add len 16 bytes 0x00000000000000000000000008060000 \
+ mask 000C priority 3 queue 3
+
+ testpmd> flex_filter 0 del len 16 bytes 0x00000000000000000000000008060000 \
+ mask 000C priority 3 queue 3
+
+
+.. _testpmd_flow_director:
+
+flow_director_filter
+~~~~~~~~~~~~~~~~~~~~
+
+The Flow Director works in receive mode to identify specific flows or sets of flows and route them to specific queues.
+
+Four types of filtering are supported which are referred to as Perfect Match, Signature, Perfect-mac-vlan and
+Perfect-tunnel filters, the match mode is set by the ``--pkt-filter-mode`` command-line parameter:
+
+* Perfect match filters.
+ The hardware checks a match between the masked fields of the received packets and the programmed filters.
+ The masked fields are for IP flow.
+
+* Signature filters.
+ The hardware checks a match between a hash-based signature of the masked fields of the received packet.
+
+* Perfect-mac-vlan match filters.
+ The hardware checks a match between the masked fields of the received packets and the programmed filters.
+ The masked fields are for MAC VLAN flow.
+
+* Perfect-tunnel match filters.
+ The hardware checks a match between the masked fields of the received packets and the programmed filters.
+ The masked fields are for tunnel flow.
+
+* Perfect-raw-flow-type match filters.
+ The hardware checks a match between the masked fields of the received packets and pre-loaded raw (template) packet.
+ The masked fields are specified by input sets.
+
+The Flow Director filters can match the different fields for different type of packet: flow type, specific input set
+per flow type and the flexible payload.
+
+The Flow Director can also mask out parts of all of these fields so that filters
+are only applied to certain fields or parts of the fields.
+
+Note that for raw flow type mode the source and destination fields in the
+raw packet buffer need to be presented in a reversed order with respect
+to the expected received packets.
+For example: IP source and destination addresses or TCP/UDP/SCTP
+source and destination ports
+
+Different NICs may have different capabilities, command show port fdir (port_id) can be used to acquire the information.
+
+# Commands to add flow director filters of different flow types::
+
+ flow_director_filter (port_id) mode IP (add|del|update) \
+ flow (ipv4-other|ipv4-frag|ipv6-other|ipv6-frag) \
+ src (src_ip_address) dst (dst_ip_address) \
+ tos (tos_value) proto (proto_value) ttl (ttl_value) \
+ vlan (vlan_value) flexbytes (flexbytes_value) \
+ (drop|fwd) pf|vf(vf_id) queue (queue_id) \
+ fd_id (fd_id_value)
+
+ flow_director_filter (port_id) mode IP (add|del|update) \
+ flow (ipv4-tcp|ipv4-udp|ipv6-tcp|ipv6-udp) \
+ src (src_ip_address) (src_port) \
+ dst (dst_ip_address) (dst_port) \
+ tos (tos_value) ttl (ttl_value) \
+ vlan (vlan_value) flexbytes (flexbytes_value) \
+ (drop|fwd) queue pf|vf(vf_id) (queue_id) \
+ fd_id (fd_id_value)
+
+ flow_director_filter (port_id) mode IP (add|del|update) \
+ flow (ipv4-sctp|ipv6-sctp) \
+ src (src_ip_address) (src_port) \
+ dst (dst_ip_address) (dst_port) \
+ tos (tos_value) ttl (ttl_value) \
+ tag (verification_tag) vlan (vlan_value) \
+ flexbytes (flexbytes_value) (drop|fwd) \
+ pf|vf(vf_id) queue (queue_id) fd_id (fd_id_value)
+
+ flow_director_filter (port_id) mode IP (add|del|update) flow l2_payload \
+ ether (ethertype) flexbytes (flexbytes_value) \
+ (drop|fwd) pf|vf(vf_id) queue (queue_id)
+ fd_id (fd_id_value)
+
+ flow_director_filter (port_id) mode MAC-VLAN (add|del|update) \
+ mac (mac_address) vlan (vlan_value) \
+ flexbytes (flexbytes_value) (drop|fwd) \
+ queue (queue_id) fd_id (fd_id_value)
+
+ flow_director_filter (port_id) mode Tunnel (add|del|update) \
+ mac (mac_address) vlan (vlan_value) \
+ tunnel (NVGRE|VxLAN) tunnel-id (tunnel_id_value) \
+ flexbytes (flexbytes_value) (drop|fwd) \
+ queue (queue_id) fd_id (fd_id_value)
+
+ flow_director_filter (port_id) mode raw (add|del|update) flow (flow_id) \
+ (drop|fwd) queue (queue_id) fd_id (fd_id_value) \
+ packet (packet file name)
+
+For example, to add an ipv4-udp flow type filter::
+
+ testpmd> flow_director_filter 0 mode IP add flow ipv4-udp src 2.2.2.3 32 \
+ dst 2.2.2.5 33 tos 2 ttl 40 vlan 0x1 flexbytes (0x88,0x48) \
+ fwd pf queue 1 fd_id 1
+
+For example, add an ipv4-other flow type filter::
+
+ testpmd> flow_director_filter 0 mode IP add flow ipv4-other src 2.2.2.3 \
+ dst 2.2.2.5 tos 2 proto 20 ttl 40 vlan 0x1 \
+ flexbytes (0x88,0x48) fwd pf queue 1 fd_id 1
+
+flush_flow_director
+~~~~~~~~~~~~~~~~~~~
+
+Flush all flow director filters on a device::
+
+ testpmd> flush_flow_director (port_id)
+
+Example, to flush all flow director filter on port 0::
-Add a tunnel filter on a port:
+ testpmd> flush_flow_director 0
-tunnel_filter add (port_id) (outer_mac) (inner_mac) (ip_addr) (inner_vlan)
- (tunnel_type) (filter_type) (tenant_id) (queue_id)
+flow_director_mask
+~~~~~~~~~~~~~~~~~~
-tunnel_filter remove
-~~~~~~~~~~~~~~~~~~~~
+Set flow director's input masks::
-Remove a tunnel filter on a port:
+ flow_director_mask (port_id) mode IP vlan (vlan_value) \
+ src_mask (ipv4_src) (ipv6_src) (src_port) \
+ dst_mask (ipv4_dst) (ipv6_dst) (dst_port)
-tunnel_filter rm (port_id) (outer_mac) (inner_mac) (ip_addr) (inner_vlan)
- (tunnel_type) (filter_type) (tenant_id) (queue_id)
+ flow_director_mask (port_id) mode MAC-VLAN vlan (vlan_value)
-rx_vxlan_port add
-~~~~~~~~~~~~~~~~~
+ flow_director_mask (port_id) mode Tunnel vlan (vlan_value) \
+ mac (mac_value) tunnel-type (tunnel_type_value) \
+ tunnel-id (tunnel_id_value)
-Add an UDP port for VXLAN packet filter on a port:
+Example, to set flow director mask on port 0::
-rx_vxlan_port add (udp_port) (port_id)
+ testpmd> flow_director_mask 0 mode IP vlan 0xefff \
+ src_mask 255.255.255.255 \
+ FFFF:FFFF:FFFF:FFFF:FFFF:FFFF:FFFF:FFFF 0xFFFF \
+ dst_mask 255.255.255.255 \
+ FFFF:FFFF:FFFF:FFFF:FFFF:FFFF:FFFF:FFFF 0xFFFF
-rx_vxlan_port remove
-~~~~~~~~~~~~~~~~~~~~
+flow_director_flex_mask
+~~~~~~~~~~~~~~~~~~~~~~~
-Remove an UDP port for VXLAN packet filter on a port:
+set masks of flow director's flexible payload based on certain flow type::
-rx_vxlan_port rm (udp_port) (port_id)
+ testpmd> flow_director_flex_mask (port_id) \
+ flow (none|ipv4-other|ipv4-frag|ipv4-tcp|ipv4-udp|ipv4-sctp| \
+ ipv6-other|ipv6-frag|ipv6-tcp|ipv6-udp|ipv6-sctp| \
+ l2_payload|all) (mask)
-tx_vlan set
-~~~~~~~~~~~
+Example, to set flow director's flex mask for all flow type on port 0::
-Set hardware insertion of VLAN ID in packets sent on a port:
+ testpmd> flow_director_flex_mask 0 flow all \
+ (0xff,0xff,0,0,0,0,0,0,0,0,0,0,0,0,0,0)
-tx_vlan set (vlan_id) (port_id)
-tx_vlan set pvid
-~~~~~~~~~~~~~~~~
+flow_director_flex_payload
+~~~~~~~~~~~~~~~~~~~~~~~~~~
-Set port based hardware insertion of VLAN ID in pacekts sent on a port:
+Configure flexible payload selection::
-tx_vlan set pvid (port_id) (vlan_id) (on|off)
+ flow_director_flex_payload (port_id) (raw|l2|l3|l4) (config)
-tx_vlan reset
-~~~~~~~~~~~~~
+For example, to select the first 16 bytes from the offset 4 (bytes) of packet's payload as flexible payload::
-Disable hardware insertion of a VLAN header in packets sent on a port:
+ testpmd> flow_director_flex_payload 0 l4 \
+ (4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19)
-tx_vlan reset (port_id)
+get_sym_hash_ena_per_port
+~~~~~~~~~~~~~~~~~~~~~~~~~
-tx_checksum set
-~~~~~~~~~~~~~~~
+Get symmetric hash enable configuration per port::
-Select hardware or software calculation of the checksum when
-transmitting a packet using the csum forward engine:
+ get_sym_hash_ena_per_port (port_id)
-tx_cksum set (ip|udp|tcp|sctp|vxlan)
+For example, to get symmetric hash enable configuration of port 1::
-ip|udp|tcp|sctp always concern the inner layer.
-vxlan concerns the outer IP and UDP layer (in case the packet
-is recognized as a vxlan packet by the forward engine)
+ testpmd> get_sym_hash_ena_per_port 1
-.. note::
+set_sym_hash_ena_per_port
+~~~~~~~~~~~~~~~~~~~~~~~~~
- Check the NIC Datasheet for hardware limits.
+Set symmetric hash enable configuration per port to enable or disable::
-tx_checksum show
-~~~~~~~~~~~~~~~~
+ set_sym_hash_ena_per_port (port_id) (enable|disable)
-Display tx checksum offload configuration:
+For example, to set symmetric hash enable configuration of port 1 to enable::
-tx_checksum show (port_id)
+ testpmd> set_sym_hash_ena_per_port 1 enable
-tso set
-~~~~~~~
+get_hash_global_config
+~~~~~~~~~~~~~~~~~~~~~~
-Enable TCP Segmentation Offload in csum forward engine:
+Get the global configurations of hash filters::
-tso set (segsize) (port_id)
+ get_hash_global_config (port_id)
-.. note::
- Please check the NIC datasheet for HW limits
+For example, to get the global configurations of hash filters of port 1::
-tso show
-~~~~~~~~
+ testpmd> get_hash_global_config 1
-Display the status of TCP Segmentation Offload:
+set_hash_global_config
+~~~~~~~~~~~~~~~~~~~~~~
-tso show (port_id)
+Set the global configurations of hash filters::
-set fwd
-~~~~~~~
+ set_hash_global_config (port_id) (toeplitz|simple_xor|symmetric_toeplitz|default) \
+ (ipv4|ipv4-frag|ipv4-tcp|ipv4-udp|ipv4-sctp|ipv4-other|ipv6|ipv6-frag| \
+ ipv6-tcp|ipv6-udp|ipv6-sctp|ipv6-other|l2_payload|<flow_id>) \
+ (enable|disable)
-Set the packet forwarding mode:
+For example, to enable simple_xor for flow type of ipv6 on port 2::
-set fwd (io|mac|mac_retry|macswap|flowgen|rxonly|txonly|csum|icmpecho)
+ testpmd> set_hash_global_config 2 simple_xor ipv6 enable
-The available information categories are:
+set_hash_input_set
+~~~~~~~~~~~~~~~~~~
-* io: forwards packets "as-is" in I/O mode.
- This is the fastest possible forwarding operation as it does not access packets data.
- This is the default mode.
+Set the input set for hash::
-* mac: changes the source and the destination Ethernet addresses of packets before forwarding them.
+ set_hash_input_set (port_id) (ipv4-frag|ipv4-tcp|ipv4-udp|ipv4-sctp| \
+ ipv4-other|ipv6-frag|ipv6-tcp|ipv6-udp|ipv6-sctp|ipv6-other| \
+ l2_payload|<flow_id>) (ovlan|ivlan|src-ipv4|dst-ipv4|src-ipv6|dst-ipv6| \
+ ipv4-tos|ipv4-proto|ipv6-tc|ipv6-next-header|udp-src-port|udp-dst-port| \
+ tcp-src-port|tcp-dst-port|sctp-src-port|sctp-dst-port|sctp-veri-tag| \
+ udp-key|gre-key|fld-1st|fld-2nd|fld-3rd|fld-4th|fld-5th|fld-6th|fld-7th| \
+ fld-8th|none) (select|add)
-* mac_retry: same as "mac" forwarding mode, but includes retries if the destination queue is full.
+For example, to add source IP to hash input set for flow type of ipv4-udp on port 0::
-* macswap: MAC swap forwarding mode.
- Swaps the source and the destination Ethernet addresses of packets before forwarding them.
+ testpmd> set_hash_input_set 0 ipv4-udp src-ipv4 add
-* flowgen: multi-flow generation mode.
- Originates a bunch of flows (varying destination IP addresses), and terminate receive traffic.
+set_fdir_input_set
+~~~~~~~~~~~~~~~~~~
-* rxonly: receives packets but doesn't transmit them.
+The Flow Director filters can match the different fields for different type of packet, i.e. specific input set
+on per flow type and the flexible payload. This command can be used to change input set for each flow type.
-* txonly: generates and transmits packets without receiving any.
+Set the input set for flow director::
-* csum: changes the checksum field with HW or SW methods depending on the offload flags on the packet.
+ set_fdir_input_set (port_id) (ipv4-frag|ipv4-tcp|ipv4-udp|ipv4-sctp| \
+ ipv4-other|ipv6|ipv6-frag|ipv6-tcp|ipv6-udp|ipv6-sctp|ipv6-other| \
+ l2_payload|<flow_id>) (ivlan|ethertype|src-ipv4|dst-ipv4|src-ipv6|dst-ipv6| \
+ ipv4-tos|ipv4-proto|ipv4-ttl|ipv6-tc|ipv6-next-header|ipv6-hop-limits| \
+ tudp-src-port|udp-dst-port|cp-src-port|tcp-dst-port|sctp-src-port| \
+ sctp-dst-port|sctp-veri-tag|none) (select|add)
-* icmpecho: receives a burst of packets, lookup for IMCP echo requests and, if any, send back ICMP echo replies.
+For example to add source IP to FD input set for flow type of ipv4-udp on port 0::
+ testpmd> set_fdir_input_set 0 ipv4-udp src-ipv4 add
-Example:
+global_config
+~~~~~~~~~~~~~
-.. code-block:: console
+Set different GRE key length for input set::
- testpmd> set fwd rxonly
+ global_config (port_id) gre-key-len (number in bytes)
- Set rxonly packet forwarding mode
+For example to set GRE key length for input set to 4 bytes on port 0::
-mac_addr add
-~~~~~~~~~~~~
+ testpmd> global_config 0 gre-key-len 4
-Add an alternative MAC address to a port:
-mac_addr add (port_id) (XX:XX:XX:XX:XX:XX)
+.. _testpmd_rte_flow:
-mac_addr remove
-~~~~~~~~~~~~~~~
+Flow rules management
+---------------------
-Remove a MAC address from a port:
+Control of the generic flow API (*rte_flow*) is fully exposed through the
+``flow`` command (validation, creation, destruction, queries and operation
+modes).
-mac_addr remove (port_id) (XX:XX:XX:XX:XX:XX)
+Considering *rte_flow* overlaps with all `Filter Functions`_, using both
+features simultaneously may cause undefined side-effects and is therefore
+not recommended.
-mac_addr add(for VF)
-~~~~~~~~~~~~~~~~~~~~
+``flow`` syntax
+~~~~~~~~~~~~~~~
-Add an alternative MAC address for a VF to a port:
+Because the ``flow`` command uses dynamic tokens to handle the large number
+of possible flow rules combinations, its behavior differs slightly from
+other commands, in particular:
-mac_add add port (port_id) vf (vf_id) (XX:XX:XX:XX:XX:XX)
+- Pressing *?* or the *<tab>* key displays contextual help for the current
+ token, not that of the entire command.
-set port-uta
-~~~~~~~~~~~~
+- Optional and repeated parameters are supported (provided they are listed
+ in the contextual help).
-Set the unicast hash filter(s) on/off for a port X:
+The first parameter stands for the operation mode. Possible operations and
+their general syntax are described below. They are covered in detail in the
+following sections.
-set port (port_id) uta (XX:XX:XX:XX:XX:XX|all) (on|off)
+- Check whether a flow rule can be created::
-set promisc
-~~~~~~~~~~~
+ flow validate {port_id}
+ [group {group_id}] [priority {level}] [ingress] [egress] [transfer]
+ pattern {item} [/ {item} [...]] / end
+ actions {action} [/ {action} [...]] / end
-Set the promiscuous mode on for a port or for all ports.
-In promiscuous mode packets are not dropped if they aren't for the specified MAC address:
+- Create a flow rule::
-set promisc (port_id|all) (on|off)
+ flow create {port_id}
+ [group {group_id}] [priority {level}] [ingress] [egress] [transfer]
+ pattern {item} [/ {item} [...]] / end
+ actions {action} [/ {action} [...]] / end
-set allmulti
-~~~~~~~~~~~~
+- Destroy specific flow rules::
-Set the allmulti mode for a port or for all ports:
+ flow destroy {port_id} rule {rule_id} [...]
-set allmulti (port_id|all) (on|off)
+- Destroy all flow rules::
-Same as the ifconfig (8) option. Controls how multicast packets are handled.
+ flow flush {port_id}
-set flow_ctrl rx
-~~~~~~~~~~~~~~~~
+- Query an existing flow rule::
-Set the link flow control parameter on a port:
+ flow query {port_id} {rule_id} {action}
-set flow_ctrl rx (on|off) tx (on|off) (high_water) (low_water) \
-(pause_time) (send_xon) (port_id)
+- List existing flow rules sorted by priority, filtered by group
+ identifiers::
-Where:
+ flow list {port_id} [group {group_id}] [...]
-high_water (integer): High threshold value to trigger XOFF.
+- Restrict ingress traffic to the defined flow rules::
-low_water (integer) : Low threshold value to trigger XON.
+ flow isolate {port_id} {boolean}
-pause_time (integer): Pause quota in the Pause frame.
+- Dump internal representation information of all flows in hardware::
-send_xon (0/1) : Send XON frame.
+ flow dump {port_id} {output_file}
-mac_ctrl_frame_fwd : Enable receiving MAC control frames
+Validating flow rules
+~~~~~~~~~~~~~~~~~~~~~
-set pfc_ctrl rx
-~~~~~~~~~~~~~~~
+``flow validate`` reports whether a flow rule would be accepted by the
+underlying device in its current state but stops short of creating it. It is
+bound to ``rte_flow_validate()``::
-Set the priority flow control parameter on a port:
+ flow validate {port_id}
+ [group {group_id}] [priority {level}] [ingress] [egress] [transfer]
+ pattern {item} [/ {item} [...]] / end
+ actions {action} [/ {action} [...]] / end
-set pfc_ctrl rx (on|off) tx (on|off) (high_water) (low_water) \ (pause_time) (priority) (port_id)
+If successful, it will show::
-Where:
+ Flow rule validated
-priority (0-7): VLAN User Priority.
+Otherwise it will show an error message of the form::
-set stat_qmap
-~~~~~~~~~~~~~
+ Caught error type [...] ([...]): [...]
-Set statistics mapping (qmapping 0..15) for RX/TX queue on port:
+This command uses the same parameters as ``flow create``, their format is
+described in `Creating flow rules`_.
-set stat_qmap (tx|rx) (port_id) (queue_id) (qmapping)
+Check whether redirecting any Ethernet packet received on port 0 to RX queue
+index 6 is supported::
-For example, to set rx queue 2 on port 0 to mapping 5:
+ testpmd> flow validate 0 ingress pattern eth / end
+ actions queue index 6 / end
+ Flow rule validated
+ testpmd>
-.. code-block:: console
+Port 0 does not support TCPv6 rules::
- testpmd>set stat_qmap rx 0 2 5
+ testpmd> flow validate 0 ingress pattern eth / ipv6 / tcp / end
+ actions drop / end
+ Caught error type 9 (specific pattern item): Invalid argument
+ testpmd>
-set port - rx/tx(for VF)
-~~~~~~~~~~~~~~~~~~~~~~~~
+Creating flow rules
+~~~~~~~~~~~~~~~~~~~
-Set VF receive/transmit from a port:
+``flow create`` validates and creates the specified flow rule. It is bound
+to ``rte_flow_create()``::
-set port (port_id) vf (vf_id) (rx|tx) (on|off)
+ flow create {port_id}
+ [group {group_id}] [priority {level}] [ingress] [egress] [transfer]
+ pattern {item} [/ {item} [...]] / end
+ actions {action} [/ {action} [...]] / end
-set port - mac address filter (for VF)
-~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+If successful, it will return a flow rule ID usable with other commands::
-Add/Remove unicast or multicast MAC addr filter for a VF:
+ Flow rule #[...] created
-set port (port_id) vf (vf_id) (mac_addr)
- (exact-mac|exact-mac-vlan|hashmac|hashmac-vlan) (on|off)
+Otherwise it will show an error message of the form::
-set port - rx mode(for VF)
-~~~~~~~~~~~~~~~~~~~~~~~~~~
+ Caught error type [...] ([...]): [...]
-Set the VF receive mode of a port:
+Parameters describe in the following order:
-set port (port_id) vf (vf_id) rxmode (AUPE|ROPE|BAM|MPE) (on|off)
+- Attributes (*group*, *priority*, *ingress*, *egress*, *transfer* tokens).
+- A matching pattern, starting with the *pattern* token and terminated by an
+ *end* pattern item.
+- Actions, starting with the *actions* token and terminated by an *end*
+ action.
-The available receive modes are:
+These translate directly to *rte_flow* objects provided as-is to the
+underlying functions.
-* AUPE: accepts untagged VLAN.
+The shortest valid definition only comprises mandatory tokens::
-* ROPE: accepts unicast hash.
+ testpmd> flow create 0 pattern end actions end
-* BAM: accepts broadcast packets
+Note that PMDs may refuse rules that essentially do nothing such as this
+one.
-* MPE: accepts all multicast packets
+**All unspecified object values are automatically initialized to 0.**
-set port - tx_rate (for Queue)
-~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+Attributes
+^^^^^^^^^^
-Set TX rate limitation for queue of a port ID:
+These tokens affect flow rule attributes (``struct rte_flow_attr``) and are
+specified before the ``pattern`` token.
-set port (port_id) queue (queue_id) rate (rate_value)
+- ``group {group id}``: priority group.
+- ``priority {level}``: priority level within group.
+- ``ingress``: rule applies to ingress traffic.
+- ``egress``: rule applies to egress traffic.
+- ``transfer``: apply rule directly to endpoints found in pattern.
-set port - tx_rate (for VF)
-~~~~~~~~~~~~~~~~~~~~~~~~~~~
+Each instance of an attribute specified several times overrides the previous
+value as shown below (group 4 is used)::
-Set TX rate limitation for queues in VF of a port ID:
+ testpmd> flow create 0 group 42 group 24 group 4 [...]
-set port (port_id) vf (vf_id) rate (rate_value) queue_mask (queue_mask)
+Note that once enabled, ``ingress`` and ``egress`` cannot be disabled.
-set port - mirror rule
-~~~~~~~~~~~~~~~~~~~~~~
+While not specifying a direction is an error, some rules may allow both
+simultaneously.
-Set port or vlan type mirror rule for a port.
+Most rules affect RX therefore contain the ``ingress`` token::
-set port (port_id) mirror-rule (rule_id) (pool-mirror|vlan-mirror) (poolmask|vlanid[,vlanid]*) dst-pool (pool_id) (on|off)
+ testpmd> flow create 0 ingress pattern [...]
-For example to enable mirror traffic with vlan 0,1 to pool 0:
+Matching pattern
+^^^^^^^^^^^^^^^^
-.. code-block:: console
+A matching pattern starts after the ``pattern`` token. It is made of pattern
+items and is terminated by a mandatory ``end`` item.
- set port 0 mirror-rule 0 vlan-mirror 0,1 dst-pool 0 on
+Items are named after their type (*RTE_FLOW_ITEM_TYPE_* from ``enum
+rte_flow_item_type``).
-reset port - mirror rule
-~~~~~~~~~~~~~~~~~~~~~~~~
+The ``/`` token is used as a separator between pattern items as shown
+below::
-Reset a mirror rule for a port.
+ testpmd> flow create 0 ingress pattern eth / ipv4 / udp / end [...]
-reset port (port_id) mirror-rule (rule_id)
+Note that protocol items like these must be stacked from lowest to highest
+layer to make sense. For instance, the following rule is either invalid or
+unlikely to match any packet::
-set flush_rx
-~~~~~~~~~~~~
+ testpmd> flow create 0 ingress pattern eth / udp / ipv4 / end [...]
-Flush (default) or don't flush RX streams before forwarding.
-Mainly used with PCAP drivers to avoid the default behavior of flushing the first 512 packets on RX streams.
+More information on these restrictions can be found in the *rte_flow*
+documentation.
-set flush_rx off
+Several items support additional specification structures, for example
+``ipv4`` allows specifying source and destination addresses as follows::
-set bypass mode
-~~~~~~~~~~~~~~~
+ testpmd> flow create 0 ingress pattern eth / ipv4 src is 10.1.1.1
+ dst is 10.2.0.0 / end [...]
-Set the bypass mode for the lowest port on bypass enabled NIC.
+This rule matches all IPv4 traffic with the specified properties.
-set bypass mode (normal|bypass|isolate) (port_id)
+In this example, ``src`` and ``dst`` are field names of the underlying
+``struct rte_flow_item_ipv4`` object. All item properties can be specified
+in a similar fashion.
-set bypass event
-~~~~~~~~~~~~~~~~
+The ``is`` token means that the subsequent value must be matched exactly,
+and assigns ``spec`` and ``mask`` fields in ``struct rte_flow_item``
+accordingly. Possible assignment tokens are:
-Set the event required to initiate specified bypass mode for the lowest port on a bypass enabled NIC where:
+- ``is``: match value perfectly (with full bit-mask).
+- ``spec``: match value according to configured bit-mask.
+- ``last``: specify upper bound to establish a range.
+- ``mask``: specify bit-mask with relevant bits set to one.
+- ``prefix``: generate bit-mask with <prefix-length> most-significant bits set to one.
-* timeout: enable bypass after watchdog timeout.
+These yield identical results::
-* os_on: enable bypass when OS/board is powered on.
+ ipv4 src is 10.1.1.1
-* os_off: enable bypass when OS/board is powered off.
+::
-* power_on: enable bypass when power supply is turned on.
+ ipv4 src spec 10.1.1.1 src mask 255.255.255.255
-* power_off: enable bypass when power supply is turned off.
+::
-set bypass event (timeout|os_on|os_off|power_on|power_off) mode (normal|bypass|isolate) (port_id)
+ ipv4 src spec 10.1.1.1 src prefix 32
-set bypass timeout
-~~~~~~~~~~~~~~~~~~
+::
-Set the bypass watchdog timeout to 'n' seconds where 0 = instant.
+ ipv4 src is 10.1.1.1 src last 10.1.1.1 # range with a single value
-set bypass timeout (0|1.5|2|3|4|8|16|32)
+::
-show bypass config
-~~~~~~~~~~~~~~~~~~
+ ipv4 src is 10.1.1.1 src last 0 # 0 disables range
-Show the bypass configuration for a bypass enabled NIC using the lowest port on the NIC.
+Inclusive ranges can be defined with ``last``::
-show bypass config (port_id)
+ ipv4 src is 10.1.1.1 src last 10.2.3.4 # 10.1.1.1 to 10.2.3.4
-set link up
-~~~~~~~~~~~
+Note that ``mask`` affects both ``spec`` and ``last``::
-Set link up for a port.
+ ipv4 src is 10.1.1.1 src last 10.2.3.4 src mask 255.255.0.0
+ # matches 10.1.0.0 to 10.2.255.255
-set link-up port (port id)
+Properties can be modified multiple times::
-set link down
-~~~~~~~~~~~~~
+ ipv4 src is 10.1.1.1 src is 10.1.2.3 src is 10.2.3.4 # matches 10.2.3.4
-Set link down for a port.
+::
-set link-down port (port id)
+ ipv4 src is 10.1.1.1 src prefix 24 src prefix 16 # matches 10.1.0.0/16
-Port Functions
---------------
+Pattern items
+^^^^^^^^^^^^^
-The following sections show functions for configuring ports.
+This section lists supported pattern items and their attributes, if any.
-.. note::
+- ``end``: end list of pattern items.
- Port configuration changes only become active when forwarding is started/restarted.
+- ``void``: no-op pattern item.
-port start
-~~~~~~~~~~
+- ``invert``: perform actions when pattern does not match.
-Start all ports or a specific port:
+- ``any``: match any protocol for the current layer.
-port start (port_id|all)
+ - ``num {unsigned}``: number of layers covered.
-port stop
-~~~~~~~~~
+- ``pf``: match traffic from/to the physical function.
-Stop all ports or a specific port:
+- ``vf``: match traffic from/to a virtual function ID.
-port stop (port_id|all)
+ - ``id {unsigned}``: VF ID.
-port close
-~~~~~~~~~~
+- ``phy_port``: match traffic from/to a specific physical port.
-Close all ports or a specific port:
+ - ``index {unsigned}``: physical port index.
-port close (port_id|all)
+- ``port_id``: match traffic from/to a given DPDK port ID.
-port start/stop queue
-~~~~~~~~~~~~~~~~~~~~~
+ - ``id {unsigned}``: DPDK port ID.
-Start/stop a rx/tx queue on a specific port:
+- ``mark``: match value set in previously matched flow rule using the mark action.
-port (port_id) (rxq|txq) (queue_id) (start|stop)
+ - ``id {unsigned}``: arbitrary integer value.
-Only take effect when port is started.
+- ``raw``: match an arbitrary byte string.
-port config - speed
-~~~~~~~~~~~~~~~~~~~
+ - ``relative {boolean}``: look for pattern after the previous item.
+ - ``search {boolean}``: search pattern from offset (see also limit).
+ - ``offset {integer}``: absolute or relative offset for pattern.
+ - ``limit {unsigned}``: search area limit for start of pattern.
+ - ``pattern {string}``: byte string to look for.
-Set the speed and duplex mode for all ports or a specific port:
+- ``eth``: match Ethernet header.
-port config (port_id|all) speed (10|100|1000|10000|auto) duplex (half|full|auto)
+ - ``dst {MAC-48}``: destination MAC.
+ - ``src {MAC-48}``: source MAC.
+ - ``type {unsigned}``: EtherType or TPID.
-port config - queues/descriptors
-~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+- ``vlan``: match 802.1Q/ad VLAN tag.
-Set number of queues/descriptors for rxq, txq, rxd and txd:
+ - ``tci {unsigned}``: tag control information.
+ - ``pcp {unsigned}``: priority code point.
+ - ``dei {unsigned}``: drop eligible indicator.
+ - ``vid {unsigned}``: VLAN identifier.
+ - ``inner_type {unsigned}``: inner EtherType or TPID.
-port config all (rxq|txq|rxd|txd) (value)
+- ``ipv4``: match IPv4 header.
-This is equivalent to the --rxq, --txq, --rxd and --txd command-line options.
+ - ``tos {unsigned}``: type of service.
+ - ``ttl {unsigned}``: time to live.
+ - ``proto {unsigned}``: next protocol ID.
+ - ``src {ipv4 address}``: source address.
+ - ``dst {ipv4 address}``: destination address.
-port config - max-pkt-len
-~~~~~~~~~~~~~~~~~~~~~~~~~
+- ``ipv6``: match IPv6 header.
-Set the maximum packet length:
+ - ``tc {unsigned}``: traffic class.
+ - ``flow {unsigned}``: flow label.
+ - ``proto {unsigned}``: protocol (next header).
+ - ``hop {unsigned}``: hop limit.
+ - ``src {ipv6 address}``: source address.
+ - ``dst {ipv6 address}``: destination address.
-port config all max-pkt-len (value)
+- ``icmp``: match ICMP header.
-This is equivalent to the --max-pkt-len command-line option.
+ - ``type {unsigned}``: ICMP packet type.
+ - ``code {unsigned}``: ICMP packet code.
-port config - CRC Strip
-~~~~~~~~~~~~~~~~~~~~~~~
+- ``udp``: match UDP header.
-Set hardware CRC stripping on or off for all ports:
+ - ``src {unsigned}``: UDP source port.
+ - ``dst {unsigned}``: UDP destination port.
-port config all crc-strip (on|off)
+- ``tcp``: match TCP header.
-CRC stripping is off by default.
+ - ``src {unsigned}``: TCP source port.
+ - ``dst {unsigned}``: TCP destination port.
-The on option is equivalent to the --crc-strip command-line option.
+- ``sctp``: match SCTP header.
-port config - RX Checksum
-~~~~~~~~~~~~~~~~~~~~~~~~~
+ - ``src {unsigned}``: SCTP source port.
+ - ``dst {unsigned}``: SCTP destination port.
+ - ``tag {unsigned}``: validation tag.
+ - ``cksum {unsigned}``: checksum.
-Set hardware RX checksum offload to on or off for all ports:
+- ``vxlan``: match VXLAN header.
-port config all rx-cksum (on|off)
+ - ``vni {unsigned}``: VXLAN identifier.
-Checksum offload is off by default.
+- ``e_tag``: match IEEE 802.1BR E-Tag header.
-The on option is equivalent to the --enable-rx-cksum command-line option.
+ - ``grp_ecid_b {unsigned}``: GRP and E-CID base.
-port config - VLAN
-~~~~~~~~~~~~~~~~~~
+- ``nvgre``: match NVGRE header.
-Set hardware VLAN on or off for all ports:
+ - ``tni {unsigned}``: virtual subnet ID.
-port config all hw-vlan (on|off)
+- ``mpls``: match MPLS header.
-Hardware VLAN is on by default.
+ - ``label {unsigned}``: MPLS label.
-The off option is equivalent to the --disable-hw-vlan command-line option.
+- ``gre``: match GRE header.
-port config - Drop Packets
-~~~~~~~~~~~~~~~~~~~~~~~~~~
+ - ``protocol {unsigned}``: protocol type.
-Set packet drop for packets with no descriptors on or off for all ports:
+- ``gre_key``: match GRE optional key field.
-port config all drop-en (on|off)
+ - ``value {unsigned}``: key value.
-Packet dropping for packets with no descriptors is off by default.
+- ``fuzzy``: fuzzy pattern match, expect faster than default.
-The on option is equivalent to the --enable-drop-en command-line option.
+ - ``thresh {unsigned}``: accuracy threshold.
-port config - RSS
-~~~~~~~~~~~~~~~~~
+- ``gtp``, ``gtpc``, ``gtpu``: match GTPv1 header.
-Set the RSS (Receive Side Scaling) mode on or off:
+ - ``teid {unsigned}``: tunnel endpoint identifier.
-port config all rss (ip|udp|none)
+- ``geneve``: match GENEVE header.
-RSS is on by default.
+ - ``vni {unsigned}``: virtual network identifier.
+ - ``protocol {unsigned}``: protocol type.
-The off option is equivalent to the --disable-rss command-line option.
+- ``vxlan-gpe``: match VXLAN-GPE header.
-port config - RSS Reta
-~~~~~~~~~~~~~~~~~~~~~~
+ - ``vni {unsigned}``: VXLAN-GPE identifier.
-Set the RSS (Receive Side Scaling) redirection table:
+- ``arp_eth_ipv4``: match ARP header for Ethernet/IPv4.
-port config all rss reta (hash,queue)[,(hash,queue)]
+ - ``sha {MAC-48}``: sender hardware address.
+ - ``spa {ipv4 address}``: sender IPv4 address.
+ - ``tha {MAC-48}``: target hardware address.
+ - ``tpa {ipv4 address}``: target IPv4 address.
-port config - DCB
-~~~~~~~~~~~~~~~~~
+- ``ipv6_ext``: match presence of any IPv6 extension header.
-Set the DCB mode for an individual port:
+ - ``next_hdr {unsigned}``: next header.
-port config (port_id) dcb vt (on|off) (traffic_class) pfc (on|off)
+- ``icmp6``: match any ICMPv6 header.
-The traffic class should be 4 or 8.
+ - ``type {unsigned}``: ICMPv6 type.
+ - ``code {unsigned}``: ICMPv6 code.
-port config - Burst
-~~~~~~~~~~~~~~~~~~~
+- ``icmp6_nd_ns``: match ICMPv6 neighbor discovery solicitation.
-Set the number of packets per burst:
+ - ``target_addr {ipv6 address}``: target address.
-port config all burst (value)
+- ``icmp6_nd_na``: match ICMPv6 neighbor discovery advertisement.
-This is equivalent to the --burst command-line option.
+ - ``target_addr {ipv6 address}``: target address.
-port config - Threshold
-~~~~~~~~~~~~~~~~~~~~~~~
+- ``icmp6_nd_opt``: match presence of any ICMPv6 neighbor discovery option.
-Set thresholds for TX/RX queues:
+ - ``type {unsigned}``: ND option type.
-port config all (threshold) (value)
+- ``icmp6_nd_opt_sla_eth``: match ICMPv6 neighbor discovery source Ethernet
+ link-layer address option.
-Where the threshold type can be:
+ - ``sla {MAC-48}``: source Ethernet LLA.
-* txpt: Set the prefetch threshold register of the TX rings, 0 <= value <= 255.
+- ``icmp6_nd_opt_tla_eth``: match ICMPv6 neighbor discovery target Ethernet
+ link-layer address option.
-* txht: Set the host threshold register of the TX rings, 0 <= value <= 255.
+ - ``tla {MAC-48}``: target Ethernet LLA.
-* txwt: Set the write-back threshold register of the TX rings, 0 <= value <= 255.
+- ``meta``: match application specific metadata.
-* rxpt: Set the prefetch threshold register of the RX rings, 0 <= value <= 255.
+ - ``data {unsigned}``: metadata value.
-* rxht: Set the host threshold register of the RX rings, 0 <= value <= 255.
+- ``gtp_psc``: match GTP PDU extension header with type 0x85.
-* rxwt: Set the write-back threshold register of the RX rings, 0 <= value <= 255.
+ - ``pdu_type {unsigned}``: PDU type.
+ - ``qfi {unsigned}``: QoS flow identifier.
-* txfreet: Set the transmit free threshold of the TX rings, 0 <= value <= txd.
+- ``pppoes``, ``pppoed``: match PPPoE header.
-* rxfreet: Set the transmit free threshold of the RX rings, 0 <= value <= rxd.
+ - ``session_id {unsigned}``: session identifier.
-* txrst: Set the transmit RS bit threshold of TX rings, 0 <= value <= txd.
- These threshold options are also available from the command-line.
+- ``pppoe_proto_id``: match PPPoE session protocol identifier.
-Flow Director Functions
------------------------
+ - ``proto_id {unsigned}``: PPP protocol identifier.
-The Flow Director works in receive mode to identify specific flows or sets of flows and route them to specific queues.
+- ``l2tpv3oip``: match L2TPv3 over IP header.
-Two types of filtering are supported which are referred to as Perfect Match and Signature filters:
+ - ``session_id {unsigned}``: L2TPv3 over IP session identifier.
-* Perfect match filters.
- The hardware checks a match between the masked fields of the received packets and the programmed filters.
+- ``ah``: match AH header.
-* Signature filters.
- The hardware checks a match between a hash-based signature of the masked fields of the received packet.
+ - ``spi {unsigned}``: security parameters index.
-The Flow Director filters can match the following fields in a packet:
+- ``pfcp``: match PFCP header.
-* Source IP and destination IP addresses.
+ - ``s_field {unsigned}``: S field.
+ - ``seid {unsigned}``: session endpoint identifier.
-* Source port and destination port numbers (for UDP and TCP packets).
+Actions list
+^^^^^^^^^^^^
-* IPv4/IPv6 and UDP/ TCP/SCTP protocol match.
+A list of actions starts after the ``actions`` token in the same fashion as
+`Matching pattern`_; actions are separated by ``/`` tokens and the list is
+terminated by a mandatory ``end`` action.
-* VLAN header.
+Actions are named after their type (*RTE_FLOW_ACTION_TYPE_* from ``enum
+rte_flow_action_type``).
-* Flexible 2-byte tuple match anywhere in the first 64 bytes of the packet.
+Dropping all incoming UDPv4 packets can be expressed as follows::
-The Flow Director can also mask out parts of all of these fields so that filters are only applied to certain fields
-or parts of the fields.
-For example it is possible to mask out sub-nets of IP addresses or to ignore VLAN headers.
+ testpmd> flow create 0 ingress pattern eth / ipv4 / udp / end
+ actions drop / end
-In the following sections, several common parameters are used in the Flow Director filters.
-These are explained below:
+Several actions have configurable properties which must be specified when
+there is no valid default value. For example, ``queue`` requires a target
+queue index.
-* src: A pair of source address values. The source IP, in IPv4 or IPv6 format, and the source port:
+This rule redirects incoming UDPv4 traffic to queue index 6::
- src 192.168.0.1 1024
+ testpmd> flow create 0 ingress pattern eth / ipv4 / udp / end
+ actions queue index 6 / end
- src 2001:DB8:85A3:0:0:8A2E:370:7000 1024
+While this one could be rejected by PMDs (unspecified queue index)::
-* dst: A pair of destination address values. The destination IP, in IPv4 or IPv6 format, and the destination port.
+ testpmd> flow create 0 ingress pattern eth / ipv4 / udp / end
+ actions queue / end
-* flexbytes: A 2-byte tuple to be matched within the first 64 bytes of a packet.
+As defined by *rte_flow*, the list is not ordered, all actions of a given
+rule are performed simultaneously. These are equivalent::
-The offset where the match occurs is set by the --pkt-filter-flexbytes-offset command-line parameter
-and is counted from the first byte of the destination Ethernet MAC address.
-The default offset is 0xC bytes, which is the "Type" word in the MAC header.
-Typically, the flexbyte value is set to 0x0800 to match the IPv4 MAC type or 0x86DD to match IPv6.
-These values change when a VLAN tag is added.
+ queue index 6 / void / mark id 42 / end
-* vlan: The VLAN header to match in the packet.
+::
-* queue: The index of the RX queue to route matched packets to.
+ void / mark id 42 / queue index 6 / end
-* soft: The 16-bit value in the MBUF flow director ID field for RX packets matching the filter.
+All actions in a list should have different types, otherwise only the last
+action of a given type is taken into account::
-add_signature_filter
-~~~~~~~~~~~~~~~~~~~~
+ queue index 4 / queue index 5 / queue index 6 / end # will use queue 6
-Add a signature filter:
+::
-# Command is displayed on several lines for clarity.
+ drop / drop / drop / end # drop is performed only once
-add_signature_filter (port_id) (ip|udp|tcp|sctp)
+::
- src (src_ip_address) (src_port)
+ mark id 42 / queue index 3 / mark id 24 / end # mark will be 24
- dst (dst_ip_address) (dst_port)
+Considering they are performed simultaneously, opposite and overlapping
+actions can sometimes be combined when the end result is unambiguous::
- flexbytes (flexbytes_values)
+ drop / queue index 6 / end # drop has no effect
- vlan (vlan_id) queue (queue_id)
+::
-upd_signature_filter
-~~~~~~~~~~~~~~~~~~~~
+ queue index 6 / rss queues 6 7 8 / end # queue has no effect
-Update a signature filter:
+::
-# Command is displayed on several lines for clarity.
+ drop / passthru / end # drop has no effect
-upd_signature_filter (port_id) (ip|udp|tcp|sctp)
+Note that PMDs may still refuse such combinations.
- src (src_ip_address) (src_port)
+Actions
+^^^^^^^
- dst (dst_ip_address) (dst_port)
+This section lists supported actions and their attributes, if any.
- flexbytes (flexbytes_values)
+- ``end``: end list of actions.
- vlan (vlan_id) queue (queue_id)
+- ``void``: no-op action.
-rm_signature_filter
-~~~~~~~~~~~~~~~~~~~
+- ``passthru``: let subsequent rule process matched packets.
-Remove a signature filter:
+- ``jump``: redirect traffic to group on device.
-# Command is displayed on several lines for clarity.
+ - ``group {unsigned}``: group to redirect to.
-rm_signature_filter (port_id) (ip|udp|tcp|sctp)
+- ``mark``: attach 32 bit value to packets.
- src (src_ip_address) (src_port)
+ - ``id {unsigned}``: 32 bit value to return with packets.
- dst (dst_ip_address) (dst_port)
+- ``flag``: flag packets.
- flexbytes (flexbytes_values)
+- ``queue``: assign packets to a given queue index.
- vlan (vlan_id)
+ - ``index {unsigned}``: queue index to use.
-add_perfect_filter
-~~~~~~~~~~~~~~~~~~
+- ``drop``: drop packets (note: passthru has priority).
-Add a perfect filter:
+- ``count``: enable counters for this rule.
-# Command is displayed on several lines for clarity.
+- ``rss``: spread packets among several queues.
-add_perfect_filter (port_id) (ip|udp|tcp|sctp)
+ - ``func {hash function}``: RSS hash function to apply, allowed tokens are
+ the same as `set_hash_global_config`_.
- src (src_ip_address) (src_port)
+ - ``level {unsigned}``: encapsulation level for ``types``.
- dst (dst_ip_address) (dst_port)
+ - ``types [{RSS hash type} [...]] end``: specific RSS hash types, allowed
+ tokens are the same as `set_hash_input_set`_, except that an empty list
+ does not disable RSS but instead requests unspecified "best-effort"
+ settings.
- flexbytes (flexbytes_values)
+ - ``key {string}``: RSS hash key, overrides ``key_len``.
- vlan (vlan_id) queue (queue_id) soft (soft_id)
+ - ``key_len {unsigned}``: RSS hash key length in bytes, can be used in
+ conjunction with ``key`` to pad or truncate it.
-upd_perfect_filter
-~~~~~~~~~~~~~~~~~~
+ - ``queues [{unsigned} [...]] end``: queue indices to use.
-Update a perfect filter:
+- ``pf``: direct traffic to physical function.
-# Command is displayed on several lines for clarity.
+- ``vf``: direct traffic to a virtual function ID.
-upd_perfect_filter (port_id) (ip|udp|tcp|sctp)
+ - ``original {boolean}``: use original VF ID if possible.
+ - ``id {unsigned}``: VF ID.
- src (src_ip_address) (src_port)
+- ``phy_port``: direct packets to physical port index.
- dst (dst_ip_address) (dst_port)
+ - ``original {boolean}``: use original port index if possible.
+ - ``index {unsigned}``: physical port index.
- flexbytes (flexbytes_values)
+- ``port_id``: direct matching traffic to a given DPDK port ID.
- vlan (vlan_id) queue (queue_id)
+ - ``original {boolean}``: use original DPDK port ID if possible.
+ - ``id {unsigned}``: DPDK port ID.
-rm_perfect_filter
-~~~~~~~~~~~~~~~~~
+- ``of_set_mpls_ttl``: OpenFlow's ``OFPAT_SET_MPLS_TTL``.
-Remove a perfect filter:
+ - ``mpls_ttl``: MPLS TTL.
-rm_perfect_filter (port_id) (ip|udp|tcp|sctp)
+- ``of_dec_mpls_ttl``: OpenFlow's ``OFPAT_DEC_MPLS_TTL``.
- src (src_ip_address) (src_port)
+- ``of_set_nw_ttl``: OpenFlow's ``OFPAT_SET_NW_TTL``.
- dst (dst_ip_address) (dst_port)
+ - ``nw_ttl``: IP TTL.
- flexbytes (flexbytes_values)
+- ``of_dec_nw_ttl``: OpenFlow's ``OFPAT_DEC_NW_TTL``.
- vlan (vlan_id) soft (soft_id)
+- ``of_copy_ttl_out``: OpenFlow's ``OFPAT_COPY_TTL_OUT``.
-set_masks_filter
-~~~~~~~~~~~~~~~~
+- ``of_copy_ttl_in``: OpenFlow's ``OFPAT_COPY_TTL_IN``.
-Set IPv4 filter masks:
+- ``of_pop_vlan``: OpenFlow's ``OFPAT_POP_VLAN``.
-# Command is displayed on several lines for clarity.
+- ``of_push_vlan``: OpenFlow's ``OFPAT_PUSH_VLAN``.
-set_masks_filter (port_id) only_ip_flow (0|1)
+ - ``ethertype``: Ethertype.
- src_mask (ip_src_mask) (src_port_mask)
+- ``of_set_vlan_vid``: OpenFlow's ``OFPAT_SET_VLAN_VID``.
- dst_mask (ip_dst_mask) (dst_port_mask)
+ - ``vlan_vid``: VLAN id.
- flexbytes (0|1) vlan_id (0|1) vlan_prio (0|1)
+- ``of_set_vlan_pcp``: OpenFlow's ``OFPAT_SET_VLAN_PCP``.
-set_ipv6_masks_filter
-~~~~~~~~~~~~~~~~~~~~~
+ - ``vlan_pcp``: VLAN priority.
-Set IPv6 filter masks:
+- ``of_pop_mpls``: OpenFlow's ``OFPAT_POP_MPLS``.
-# Command is displayed on several lines for clarity.
+ - ``ethertype``: Ethertype.
-set_ipv6_masks_filter (port_id) only_ip_flow (0|1)
+- ``of_push_mpls``: OpenFlow's ``OFPAT_PUSH_MPLS``.
- src_mask (ip_src_mask) (src_port_mask)
+ - ``ethertype``: Ethertype.
- dst_mask (ip_dst_mask) (dst_port_mask)
+- ``vxlan_encap``: Performs a VXLAN encapsulation, outer layer configuration
+ is done through `Config VXLAN Encap outer layers`_.
- flexbytes (0|1) vlan_id (0|1) vlan_prio (0|1)
+- ``vxlan_decap``: Performs a decapsulation action by stripping all headers of
+ the VXLAN tunnel network overlay from the matched flow.
- compare_dst (0|1)
+- ``nvgre_encap``: Performs a NVGRE encapsulation, outer layer configuration
+ is done through `Config NVGRE Encap outer layers`_.
-Link Bonding Functions
-----------------------
+- ``nvgre_decap``: Performs a decapsulation action by stripping all headers of
+ the NVGRE tunnel network overlay from the matched flow.
-The Link Bonding functions make it possible to dynamically create and
-manage link bonding devices from within testpmd interactive prompt.
+- ``l2_encap``: Performs a L2 encapsulation, L2 configuration
+ is done through `Config L2 Encap`_.
-create bonded device
-~~~~~~~~~~~~~~~~~~~~
+- ``l2_decap``: Performs a L2 decapsulation, L2 configuration
+ is done through `Config L2 Decap`_.
-Create a new bonding device:
+- ``mplsogre_encap``: Performs a MPLSoGRE encapsulation, outer layer
+ configuration is done through `Config MPLSoGRE Encap outer layers`_.
-create bonded device (mode) (socket)
+- ``mplsogre_decap``: Performs a MPLSoGRE decapsulation, outer layer
+ configuration is done through `Config MPLSoGRE Decap outer layers`_.
-For example, to create a bonded device in mode 1 on socket 0.
+- ``mplsoudp_encap``: Performs a MPLSoUDP encapsulation, outer layer
+ configuration is done through `Config MPLSoUDP Encap outer layers`_.
-.. code-block:: console
+- ``mplsoudp_decap``: Performs a MPLSoUDP decapsulation, outer layer
+ configuration is done through `Config MPLSoUDP Decap outer layers`_.
- testpmd> create bonded 1 0
- created new bonded device (port X)
+- ``set_ipv4_src``: Set a new IPv4 source address in the outermost IPv4 header.
-add bonding slave
-~~~~~~~~~~~~~~~~~
+ - ``ipv4_addr``: New IPv4 source address.
-Adds Ethernet device to a Link Bonding device:
+- ``set_ipv4_dst``: Set a new IPv4 destination address in the outermost IPv4
+ header.
-add bonding slave (slave id) (port id)
+ - ``ipv4_addr``: New IPv4 destination address.
-For example, to add Ethernet device (port 6) to a Link Bonding device (port 10).
+- ``set_ipv6_src``: Set a new IPv6 source address in the outermost IPv6 header.
-.. code-block:: console
+ - ``ipv6_addr``: New IPv6 source address.
- testpmd> add bonding slave 6 10
+- ``set_ipv6_dst``: Set a new IPv6 destination address in the outermost IPv6
+ header.
+ - ``ipv6_addr``: New IPv6 destination address.
-remove bonding slave
-~~~~~~~~~~~~~~~~~~~~
+- ``set_tp_src``: Set a new source port number in the outermost TCP/UDP
+ header.
-Removes an Ethernet slave device from a Link Bonding device:
+ - ``port``: New TCP/UDP source port number.
-remove bonding slave (slave id) (port id)
+- ``set_tp_dst``: Set a new destination port number in the outermost TCP/UDP
+ header.
-For example, to remove Ethernet slave device (port 6) to a Link Bonding device (port 10).
+ - ``port``: New TCP/UDP destination port number.
-.. code-block:: console
+- ``mac_swap``: Swap the source and destination MAC addresses in the outermost
+ Ethernet header.
- testpmd> remove bonding slave 6 10
+- ``dec_ttl``: Performs a decrease TTL value action
-set bonding mode
-~~~~~~~~~~~~~~~~
+- ``set_ttl``: Set TTL value with specified value
+ - ``ttl_value {unsigned}``: The new TTL value to be set
-Set the Link Bonding mode of a Link Bonding device:
+- ``set_mac_src``: set source MAC address
-set bonding mode (value) (port id)
+ - ``mac_addr {MAC-48}``: new source MAC address
-For example, to set the bonding mode of a Link Bonding device (port 10) to broadcast (mode 3).
+- ``set_mac_dst``: set destination MAC address
-.. code-block:: console
+ - ``mac_addr {MAC-48}``: new destination MAC address
- testpmd> set bonding mode 3 10
+- ``inc_tcp_seq``: Increase sequence number in the outermost TCP header.
-set bonding primary
-~~~~~~~~~~~~~~~~~~~
+ - ``value {unsigned}``: Value to increase TCP sequence number by.
-Set an Ethernet slave device as the primary device on a Link Bonding device:
+- ``dec_tcp_seq``: Decrease sequence number in the outermost TCP header.
-set bonding primary (slave id) (port id)
+ - ``value {unsigned}``: Value to decrease TCP sequence number by.
-For example, to set the Ethernet slave device (port 6) as the primary port of a Link Bonding device (port 10).
+- ``inc_tcp_ack``: Increase acknowledgment number in the outermost TCP header.
-.. code-block:: console
+ - ``value {unsigned}``: Value to increase TCP acknowledgment number by.
- testpmd> set bonding primary 6 10
+- ``dec_tcp_ack``: Decrease acknowledgment number in the outermost TCP header.
-set bonding mac
-~~~~~~~~~~~~~~~
+ - ``value {unsigned}``: Value to decrease TCP acknowledgment number by.
-Set the MAC address of a Link Bonding device:
+- ``set_ipv4_dscp``: Set IPv4 DSCP value with specified value
-set bonding mac (port id) (mac)
+ - ``dscp_value {unsigned}``: The new DSCP value to be set
-For example, to set the MAC address of a Link Bonding device (port 10) to 00:00:00:00:00:01
+- ``set_ipv6_dscp``: Set IPv6 DSCP value with specified value
-.. code-block:: console
+ - ``dscp_value {unsigned}``: The new DSCP value to be set
- testpmd> set bonding mac 10 00:00:00:00:00:01
+Destroying flow rules
+~~~~~~~~~~~~~~~~~~~~~
-set bonding xmit_balance_policy
-~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+``flow destroy`` destroys one or more rules from their rule ID (as returned
+by ``flow create``), this command calls ``rte_flow_destroy()`` as many
+times as necessary::
-Set the transmission policy for a Link Bonding device when it is in Balance XOR mode:
+ flow destroy {port_id} rule {rule_id} [...]
-set bonding xmit_balance_policy (port_id) (l2|l23|l34)
+If successful, it will show::
-For example, set a Link Bonding device (port 10) to use a balance policy of layer 3+4 (IP addresses & UDP ports )
+ Flow rule #[...] destroyed
-.. code-block:: console
+It does not report anything for rule IDs that do not exist. The usual error
+message is shown when a rule cannot be destroyed::
- testpmd> set bonding xmit_balance_policy 10 l34
+ Caught error type [...] ([...]): [...]
+``flow flush`` destroys all rules on a device and does not take extra
+arguments. It is bound to ``rte_flow_flush()``::
-set bonding mon_period
-~~~~~~~~~~~~~~~~~~~~~~
+ flow flush {port_id}
-Set the link status monitoring polling period in milliseconds for a bonding devicie.
+Any errors are reported as above.
-This adds support for PMD slave devices which do not support link status interrupts.
-When the mon_period is set to a value greater than 0 then all PMD's which do not support
-link status ISR will be queried every polling interval to check if their link status has changed.
+Creating several rules and destroying them::
-set bonding mon_period (port_id) (value)
+ testpmd> flow create 0 ingress pattern eth / ipv6 / end
+ actions queue index 2 / end
+ Flow rule #0 created
+ testpmd> flow create 0 ingress pattern eth / ipv4 / end
+ actions queue index 3 / end
+ Flow rule #1 created
+ testpmd> flow destroy 0 rule 0 rule 1
+ Flow rule #1 destroyed
+ Flow rule #0 destroyed
+ testpmd>
-For example, to set the link status monitoring polling period of bonded device (port 5) to 150ms
+The same result can be achieved using ``flow flush``::
-.. code-block:: console
+ testpmd> flow create 0 ingress pattern eth / ipv6 / end
+ actions queue index 2 / end
+ Flow rule #0 created
+ testpmd> flow create 0 ingress pattern eth / ipv4 / end
+ actions queue index 3 / end
+ Flow rule #1 created
+ testpmd> flow flush 0
+ testpmd>
- testpmd> set bonding mon_period 5 150
+Non-existent rule IDs are ignored::
+ testpmd> flow create 0 ingress pattern eth / ipv6 / end
+ actions queue index 2 / end
+ Flow rule #0 created
+ testpmd> flow create 0 ingress pattern eth / ipv4 / end
+ actions queue index 3 / end
+ Flow rule #1 created
+ testpmd> flow destroy 0 rule 42 rule 10 rule 2
+ testpmd>
+ testpmd> flow destroy 0 rule 0
+ Flow rule #0 destroyed
+ testpmd>
-show bonding config
+Querying flow rules
~~~~~~~~~~~~~~~~~~~
-Show the current configuration of a Link Bonding device:
+``flow query`` queries a specific action of a flow rule having that
+ability. Such actions collect information that can be reported using this
+command. It is bound to ``rte_flow_query()``::
-show bonding config (port id)
+ flow query {port_id} {rule_id} {action}
-For example,
-to show the configuration a Link Bonding device (port 9) with 3 slave devices (1, 3, 4)
-in balance mode with a transmission policy of layer 2+3.
+If successful, it will display either the retrieved data for known actions
+or the following message::
-.. code-block:: console
+ Cannot display result for action type [...] ([...])
- testpmd> show bonding config 9
- Bonding mode: 2
- Balance Xmit Policy: BALANCE_XMIT_POLICY_LAYER23
- Slaves (3): [1 3 4]
- Active Slaves (3): [1 3 4]
- Primary: [3]
+Otherwise, it will complain either that the rule does not exist or that some
+error occurred::
-Register Functions
-------------------
+ Flow rule #[...] not found
-The Register functions can be used to read from and write to registers on the network card referenced by a port number.
-This is mainly useful for debugging purposes.
-Reference should be made to the appropriate datasheet for the network card for details on the register addresses
-and fields that can be accessed.
+::
-read reg
-~~~~~~~~
+ Caught error type [...] ([...]): [...]
-Display the value of a port register:
+Currently only the ``count`` action is supported. This action reports the
+number of packets that hit the flow rule and the total number of bytes. Its
+output has the following format::
-read reg (port_id) (address)
+ count:
+ hits_set: [...] # whether "hits" contains a valid value
+ bytes_set: [...] # whether "bytes" contains a valid value
+ hits: [...] # number of packets
+ bytes: [...] # number of bytes
-For example, to examine the Flow Director control register (FDIRCTL, 0x0000EE000) on an Intel® 82599 10 GbE Controller:
+Querying counters for TCPv6 packets redirected to queue 6::
-.. code-block:: console
+ testpmd> flow create 0 ingress pattern eth / ipv6 / tcp / end
+ actions queue index 6 / count / end
+ Flow rule #4 created
+ testpmd> flow query 0 4 count
+ count:
+ hits_set: 1
+ bytes_set: 0
+ hits: 386446
+ bytes: 0
+ testpmd>
- testpmd> read reg 0 0xEE00
- port 0 PCI register at offset 0xEE00: 0x4A060029 (1241907241)
+Listing flow rules
+~~~~~~~~~~~~~~~~~~
-read regfield
-~~~~~~~~~~~~~
+``flow list`` lists existing flow rules sorted by priority and optionally
+filtered by group identifiers::
+
+ flow list {port_id} [group {group_id}] [...]
+
+This command only fails with the following message if the device does not
+exist::
+
+ Invalid port [...]
+
+Output consists of a header line followed by a short description of each
+flow rule, one per line. There is no output at all when no flow rules are
+configured on the device::
+
+ ID Group Prio Attr Rule
+ [...] [...] [...] [...] [...]
+
+``Attr`` column flags:
+
+- ``i`` for ``ingress``.
+- ``e`` for ``egress``.
+
+Creating several flow rules and listing them::
+
+ testpmd> flow create 0 ingress pattern eth / ipv4 / end
+ actions queue index 6 / end
+ Flow rule #0 created
+ testpmd> flow create 0 ingress pattern eth / ipv6 / end
+ actions queue index 2 / end
+ Flow rule #1 created
+ testpmd> flow create 0 priority 5 ingress pattern eth / ipv4 / udp / end
+ actions rss queues 6 7 8 end / end
+ Flow rule #2 created
+ testpmd> flow list 0
+ ID Group Prio Attr Rule
+ 0 0 0 i- ETH IPV4 => QUEUE
+ 1 0 0 i- ETH IPV6 => QUEUE
+ 2 0 5 i- ETH IPV4 UDP => RSS
+ testpmd>
+
+Rules are sorted by priority (i.e. group ID first, then priority level)::
+
+ testpmd> flow list 1
+ ID Group Prio Attr Rule
+ 0 0 0 i- ETH => COUNT
+ 6 0 500 i- ETH IPV6 TCP => DROP COUNT
+ 5 0 1000 i- ETH IPV6 ICMP => QUEUE
+ 1 24 0 i- ETH IPV4 UDP => QUEUE
+ 4 24 10 i- ETH IPV4 TCP => DROP
+ 3 24 20 i- ETH IPV4 => DROP
+ 2 24 42 i- ETH IPV4 UDP => QUEUE
+ 7 63 0 i- ETH IPV6 UDP VXLAN => MARK QUEUE
+ testpmd>
+
+Output can be limited to specific groups::
+
+ testpmd> flow list 1 group 0 group 63
+ ID Group Prio Attr Rule
+ 0 0 0 i- ETH => COUNT
+ 6 0 500 i- ETH IPV6 TCP => DROP COUNT
+ 5 0 1000 i- ETH IPV6 ICMP => QUEUE
+ 7 63 0 i- ETH IPV6 UDP VXLAN => MARK QUEUE
+ testpmd>
+
+Toggling isolated mode
+~~~~~~~~~~~~~~~~~~~~~~
-Display a port register bit field:
+``flow isolate`` can be used to tell the underlying PMD that ingress traffic
+must only be injected from the defined flow rules; that no default traffic
+is expected outside those rules and the driver is free to assign more
+resources to handle them. It is bound to ``rte_flow_isolate()``::
-read regfield (port_id) (address) (bit_x) (bit_y)
+ flow isolate {port_id} {boolean}
-For example, reading the lowest two bits from the register in the example above:
+If successful, enabling or disabling isolated mode shows either::
-.. code-block:: console
+ Ingress traffic on port [...]
+ is now restricted to the defined flow rules
- testpmd> read regfield 0 0xEE00 0 1
- port 0 PCI register at offset 0xEE00: bits[0, 1]=0x1 (1)
+Or::
-read regbit
-~~~~~~~~~~~
+ Ingress traffic on port [...]
+ is not restricted anymore to the defined flow rules
-Display a single port register bit:
+Otherwise, in case of error::
-read regbit (port_id) (address) (bit_x)
+ Caught error type [...] ([...]): [...]
-For example, reading the lowest bit from the register in the example above:
+Mainly due to its side effects, PMDs supporting this mode may not have the
+ability to toggle it more than once without reinitializing affected ports
+first (e.g. by exiting testpmd).
-.. code-block:: console
+Enabling isolated mode::
- testpmd> read regbit 0 0xEE00 0
- port 0 PCI register at offset 0xEE00: bit 0=1
+ testpmd> flow isolate 0 true
+ Ingress traffic on port 0 is now restricted to the defined flow rules
+ testpmd>
-write reg
-~~~~~~~~~
+Disabling isolated mode::
-Set the value of a port register:
+ testpmd> flow isolate 0 false
+ Ingress traffic on port 0 is not restricted anymore to the defined flow rules
+ testpmd>
-write reg (port_id) (address) (value)
+Dumping HW internal information
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
-For example, to clear a register:
+``flow dump`` dumps the hardware's internal representation information of
+all flows. It is bound to ``rte_flow_dev_dump()``::
-.. code-block:: console
+ flow dump {port_id} {output_file}
- testpmd> write reg 0 0xEE00 0x0
- port 0 PCI register at offset 0xEE00: 0x00000000 (0)
+If successful, it will show::
-write regfield
-~~~~~~~~~~~~~~
+ Flow dump finished
-Set bit field of a port register:
+Otherwise, it will complain error occurred::
-write regfield (port_id) (address) (bit_x) (bit_y) (value)
+ Caught error type [...] ([...]): [...]
-For example, writing to the register cleared in the example above:
+Sample QinQ flow rules
+~~~~~~~~~~~~~~~~~~~~~~
-.. code-block:: console
+Before creating QinQ rule(s) the following commands should be issued to enable QinQ::
- testpmd> write regfield 0 0xEE00 0 1 2
- port 0 PCI register at offset 0xEE00: 0x00000002 (2)
+ testpmd> port stop 0
+ testpmd> vlan set qinq_strip on 0
-write regbit
-~~~~~~~~~~~~
+The above command sets the inner and outer TPID's to 0x8100.
-Set single bit value of a port register:
+To change the TPID's the following commands should be used::
-write regbit (port_id) (address) (bit_x) (value)
+ testpmd> vlan set outer tpid 0xa100 0
+ testpmd> vlan set inner tpid 0x9100 0
+ testpmd> port start 0
-For example, to set the high bit in the register from the example above:
+Validate and create a QinQ rule on port 0 to steer traffic to a VF queue in a VM.
-.. code-block:: console
+::
- testpmd> write regbit 0 0xEE00 31 1
- port 0 PCI register at offset 0xEE00: 0x8000000A (2147483658)
+ testpmd> flow validate 0 ingress pattern eth / vlan tci is 123 /
+ vlan tci is 456 / end actions vf id 1 / queue index 0 / end
+ Flow rule #0 validated
-Filter Functions
-----------------
+ testpmd> flow create 0 ingress pattern eth / vlan tci is 4 /
+ vlan tci is 456 / end actions vf id 123 / queue index 0 / end
+ Flow rule #0 created
-This section details the available filter functions that are available.
+ testpmd> flow list 0
+ ID Group Prio Attr Rule
+ 0 0 0 i- ETH VLAN VLAN=>VF QUEUE
-ethertype_filter
-~~~~~~~~~~~~~~~~~~~~
+Validate and create a QinQ rule on port 0 to steer traffic to a queue on the host.
-Add or delete a L2 Ethertype filter, which identify packets by their L2 Ethertype mainly assign them to a receive queue.
+::
-ethertype_filter (port_id) (add|del) (mac_addr|mac_ignr) (mac_address) ethertype (ether_type) (drop|fwd) queue (queue_id)
+ testpmd> flow validate 0 ingress pattern eth / vlan tci is 321 /
+ vlan tci is 654 / end actions pf / queue index 0 / end
+ Flow rule #1 validated
-The available information parameters are:
+ testpmd> flow create 0 ingress pattern eth / vlan tci is 321 /
+ vlan tci is 654 / end actions pf / queue index 1 / end
+ Flow rule #1 created
-* port_id: the port which the Ethertype filter assigned on.
+ testpmd> flow list 0
+ ID Group Prio Attr Rule
+ 0 0 0 i- ETH VLAN VLAN=>VF QUEUE
+ 1 0 0 i- ETH VLAN VLAN=>PF QUEUE
-* mac_addr: compare destination mac address.
+Sample VXLAN encapsulation rule
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
-* mac_ignr: ignore destination mac address match.
+VXLAN encapsulation outer layer has default value pre-configured in testpmd
+source code, those can be changed by using the following commands
-* mac_address: destination mac address to match.
+IPv4 VXLAN outer header::
-* ether_type: the EtherType value want to match,
- for example 0x0806 for ARP packet. 0x0800 (IPv4) and 0x86DD (IPv6) are invalid.
+ testpmd> set vxlan ip-version ipv4 vni 4 udp-src 4 udp-dst 4 ip-src 127.0.0.1
+ ip-dst 128.0.0.1 eth-src 11:11:11:11:11:11 eth-dst 22:22:22:22:22:22
+ testpmd> flow create 0 ingress pattern end actions vxlan_encap /
+ queue index 0 / end
-* queue_id : The receive queue associated with this EtherType filter. It is meaningless when deleting or dropping.
+ testpmd> set vxlan-with-vlan ip-version ipv4 vni 4 udp-src 4 udp-dst 4 ip-src
+ 127.0.0.1 ip-dst 128.0.0.1 vlan-tci 34 eth-src 11:11:11:11:11:11
+ eth-dst 22:22:22:22:22:22
+ testpmd> flow create 0 ingress pattern end actions vxlan_encap /
+ queue index 0 / end
-Example, to add/remove an ethertype filter rule:
+ testpmd> set vxlan-tos-ttl ip-version ipv4 vni 4 udp-src 4 udp-dst 4 ip-tos 0
+ ip-ttl 255 ip-src 127.0.0.1 ip-dst 128.0.0.1 eth-src 11:11:11:11:11:11
+ eth-dst 22:22:22:22:22:22
+ testpmd> flow create 0 ingress pattern end actions vxlan_encap /
+ queue index 0 / end
-.. code-block:: console
+IPv6 VXLAN outer header::
- testpmd> ethertype_filter 0 add mac_ignr ethertype 0x0806 fwd queue 3
- testpmd> ethertype_filter 0 del mac_ignr ethertype 0x0806 fwd queue 3
+ testpmd> set vxlan ip-version ipv6 vni 4 udp-src 4 udp-dst 4 ip-src ::1
+ ip-dst ::2222 eth-src 11:11:11:11:11:11 eth-dst 22:22:22:22:22:22
+ testpmd> flow create 0 ingress pattern end actions vxlan_encap /
+ queue index 0 / end
-add_2tuple_filter
-~~~~~~~~~~~~~~~~~
+ testpmd> set vxlan-with-vlan ip-version ipv6 vni 4 udp-src 4 udp-dst 4
+ ip-src ::1 ip-dst ::2222 vlan-tci 34 eth-src 11:11:11:11:11:11
+ eth-dst 22:22:22:22:22:22
+ testpmd> flow create 0 ingress pattern end actions vxlan_encap /
+ queue index 0 / end
-Add a 2-tuple filter,
-which identify packets by specific protocol and destination TCP/UDP port
-and forwards packets into one of the receive queues.
+ testpmd> set vxlan-tos-ttl ip-version ipv6 vni 4 udp-src 4 udp-dst 4
+ ip-tos 0 ip-ttl 255 ::1 ip-dst ::2222 eth-src 11:11:11:11:11:11
+ eth-dst 22:22:22:22:22:22
+ testpmd> flow create 0 ingress pattern end actions vxlan_encap /
+ queue index 0 / end
-add_2tuple_filter (port_id) protocol (pro_value) (pro_mask) dst_port (port_value) (port_mask)
-flags (flg_value) priority (prio_value) queue (queue_id) index (idx)
+Sample NVGRE encapsulation rule
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
-The available information parameters are:
+NVGRE encapsulation outer layer has default value pre-configured in testpmd
+source code, those can be changed by using the following commands
-* port_id: the port which the 2-tuple filter assigned on.
+IPv4 NVGRE outer header::
-* pro_value: IP L4 protocol
+ testpmd> set nvgre ip-version ipv4 tni 4 ip-src 127.0.0.1 ip-dst 128.0.0.1
+ eth-src 11:11:11:11:11:11 eth-dst 22:22:22:22:22:22
+ testpmd> flow create 0 ingress pattern end actions nvgre_encap /
+ queue index 0 / end
-* pro_mask: protocol participates in the match or not, 1 means participate
+ testpmd> set nvgre-with-vlan ip-version ipv4 tni 4 ip-src 127.0.0.1
+ ip-dst 128.0.0.1 vlan-tci 34 eth-src 11:11:11:11:11:11
+ eth-dst 22:22:22:22:22:22
+ testpmd> flow create 0 ingress pattern end actions nvgre_encap /
+ queue index 0 / end
-* port_value: destination port in L4.
+IPv6 NVGRE outer header::
-* port_mask: destination port participates in the match or not, 1 means participate.
+ testpmd> set nvgre ip-version ipv6 tni 4 ip-src ::1 ip-dst ::2222
+ eth-src 11:11:11:11:11:11 eth-dst 22:22:22:22:22:22
+ testpmd> flow create 0 ingress pattern end actions nvgre_encap /
+ queue index 0 / end
-* flg_value: TCP control bits. The non-zero value is invalid, when the pro_value is not set to 0x06 (TCP).
+ testpmd> set nvgre-with-vlan ip-version ipv6 tni 4 ip-src ::1 ip-dst ::2222
+ vlan-tci 34 eth-src 11:11:11:11:11:11 eth-dst 22:22:22:22:22:22
+ testpmd> flow create 0 ingress pattern end actions nvgre_encap /
+ queue index 0 / end
-* prio_value: the priority of this filter.
+Sample L2 encapsulation rule
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~
-* queue_id: The receive queue associated with this 2-tuple filter
+L2 encapsulation has default value pre-configured in testpmd
+source code, those can be changed by using the following commands
-* index: the index of this 2-tuple filter
+L2 header::
-Example:
+ testpmd> set l2_encap ip-version ipv4
+ eth-src 11:11:11:11:11:11 eth-dst 22:22:22:22:22:22
+ testpmd> flow create 0 ingress pattern eth / ipv4 / udp / mpls / end actions
+ mplsoudp_decap / l2_encap / end
-.. code-block:: console
+L2 with VXLAN header::
- testpmd> add_2tuple_filter 0 protocol 0x06 1 dst_port 32 1 flags 0x02 priority 3 queue 3 index 0
+ testpmd> set l2_encap-with-vlan ip-version ipv4 vlan-tci 34
+ eth-src 11:11:11:11:11:11 eth-dst 22:22:22:22:22:22
+ testpmd> flow create 0 ingress pattern eth / ipv4 / udp / mpls / end actions
+ mplsoudp_decap / l2_encap / end
-remove_2tuple_filter
-~~~~~~~~~~~~~~~~~~~~
+Sample L2 decapsulation rule
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~
-Remove a 2-tuple filter
+L2 decapsulation has default value pre-configured in testpmd
+source code, those can be changed by using the following commands
-remove_2tuple_filter (port_id) index (idx)
+L2 header::
-get_2tuple_filter
-~~~~~~~~~~~~~~~~~
+ testpmd> set l2_decap
+ testpmd> flow create 0 egress pattern eth / end actions l2_decap / mplsoudp_encap /
+ queue index 0 / end
-Get and display a 2-tuple filter
+L2 with VXLAN header::
-get_2tuple_filter (port_id) index (idx)
+ testpmd> set l2_encap-with-vlan
+ testpmd> flow create 0 egress pattern eth / end actions l2_encap / mplsoudp_encap /
+ queue index 0 / end
-Example:
+Sample MPLSoGRE encapsulation rule
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
-.. code-block:: console
+MPLSoGRE encapsulation outer layer has default value pre-configured in testpmd
+source code, those can be changed by using the following commands
- testpmd> get_2tuple_filter 0 index 0
+IPv4 MPLSoGRE outer header::
- filter[0]:
- Destination Port: 0x0020 mask: 1
- protocol: 0x06 mask:1 tcp_flags: 0x02
- priority: 3 queue: 3
+ testpmd> set mplsogre_encap ip-version ipv4 label 4
+ ip-src 127.0.0.1 ip-dst 128.0.0.1 eth-src 11:11:11:11:11:11
+ eth-dst 22:22:22:22:22:22
+ testpmd> flow create 0 egress pattern eth / end actions l2_decap /
+ mplsogre_encap / end
-add_5tuple_filter
-~~~~~~~~~~~~~~~~~
+IPv4 MPLSoGRE with VLAN outer header::
-Add a 5-tuple filter,
-which consists of a 5-tuple (protocol, source and destination IP addresses, source and destination TCP/UDP/SCTP port)
-and routes packets into one of the receive queues.
+ testpmd> set mplsogre_encap-with-vlan ip-version ipv4 label 4
+ ip-src 127.0.0.1 ip-dst 128.0.0.1 vlan-tci 34
+ eth-src 11:11:11:11:11:11 eth-dst 22:22:22:22:22:22
+ testpmd> flow create 0 egress pattern eth / end actions l2_decap /
+ mplsogre_encap / end
-add_5tuple_filter (port_id) dst_ip (dst_address) src_ip (src_address) dst_port (dst_port_value) src_port (src_port_value)
-protocol (protocol_value) mask (mask_value) flags (flags_value) priority (prio_value) queue (queue_id) index (idx)
+IPv6 MPLSoGRE outer header::
-The available information parameters are:
+ testpmd> set mplsogre_encap ip-version ipv6 mask 4
+ ip-src ::1 ip-dst ::2222 eth-src 11:11:11:11:11:11
+ eth-dst 22:22:22:22:22:22
+ testpmd> flow create 0 egress pattern eth / end actions l2_decap /
+ mplsogre_encap / end
-* port_id: the port which the 5-tuple filter assigned on.
+IPv6 MPLSoGRE with VLAN outer header::
-* dst_address: destination IP address.
+ testpmd> set mplsogre_encap-with-vlan ip-version ipv6 mask 4
+ ip-src ::1 ip-dst ::2222 vlan-tci 34
+ eth-src 11:11:11:11:11:11 eth-dst 22:22:22:22:22:22
+ testpmd> flow create 0 egress pattern eth / end actions l2_decap /
+ mplsogre_encap / end
-* src_address: source IP address.
+Sample MPLSoGRE decapsulation rule
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
-* dst_port_value: TCP/UDP destination port.
+MPLSoGRE decapsulation outer layer has default value pre-configured in testpmd
+source code, those can be changed by using the following commands
-* src_port_value: TCP/UDP source port.
+IPv4 MPLSoGRE outer header::
-* protocol_value: L4 protocol.
+ testpmd> set mplsogre_decap ip-version ipv4
+ testpmd> flow create 0 ingress pattern eth / ipv4 / gre / mpls / end actions
+ mplsogre_decap / l2_encap / end
-* mask_value: participates in the match or not by bit for field above, 1b means participate
+IPv4 MPLSoGRE with VLAN outer header::
-* flags_value: TCP control bits. The non-zero value is invalid, when the protocol_value is not set to 0x06 (TCP).
+ testpmd> set mplsogre_decap-with-vlan ip-version ipv4
+ testpmd> flow create 0 ingress pattern eth / vlan / ipv4 / gre / mpls / end
+ actions mplsogre_decap / l2_encap / end
-* prio_value: the priority of this filter.
+IPv6 MPLSoGRE outer header::
-* queue_id: The receive queue associated with this 5-tuple filter.
+ testpmd> set mplsogre_decap ip-version ipv6
+ testpmd> flow create 0 ingress pattern eth / ipv6 / gre / mpls / end
+ actions mplsogre_decap / l2_encap / end
-* index: the index of this 5-tuple filter
+IPv6 MPLSoGRE with VLAN outer header::
-Example:
+ testpmd> set mplsogre_decap-with-vlan ip-version ipv6
+ testpmd> flow create 0 ingress pattern eth / vlan / ipv6 / gre / mpls / end
+ actions mplsogre_decap / l2_encap / end
-.. code-block:: console
+Sample MPLSoUDP encapsulation rule
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
- testpmd> add_5tuple_filter 1 dst_ip 2.2.2.5 src_ip 2.2.2.4 dst_port 64 src_port 32 protocol 0x06 mask 0x1F flags 0x0 priority 3 queue 3 index 0
+MPLSoUDP encapsulation outer layer has default value pre-configured in testpmd
+source code, those can be changed by using the following commands
-remove_5tuple_filter
-~~~~~~~~~~~~~~~~~~~~
+IPv4 MPLSoUDP outer header::
-Remove a 5-tuple filter
+ testpmd> set mplsoudp_encap ip-version ipv4 label 4 udp-src 5 udp-dst 10
+ ip-src 127.0.0.1 ip-dst 128.0.0.1 eth-src 11:11:11:11:11:11
+ eth-dst 22:22:22:22:22:22
+ testpmd> flow create 0 egress pattern eth / end actions l2_decap /
+ mplsoudp_encap / end
-remove_5tuple_filter (port_id) index (idx)
+IPv4 MPLSoUDP with VLAN outer header::
-get_5tuple_filter
-~~~~~~~~~~~~~~~~~
+ testpmd> set mplsoudp_encap-with-vlan ip-version ipv4 label 4 udp-src 5
+ udp-dst 10 ip-src 127.0.0.1 ip-dst 128.0.0.1 vlan-tci 34
+ eth-src 11:11:11:11:11:11 eth-dst 22:22:22:22:22:22
+ testpmd> flow create 0 egress pattern eth / end actions l2_decap /
+ mplsoudp_encap / end
-Get and display a 5-tuple filter
+IPv6 MPLSoUDP outer header::
-get_5tuple_filter (port_id) index (idx)
+ testpmd> set mplsoudp_encap ip-version ipv6 mask 4 udp-src 5 udp-dst 10
+ ip-src ::1 ip-dst ::2222 eth-src 11:11:11:11:11:11
+ eth-dst 22:22:22:22:22:22
+ testpmd> flow create 0 egress pattern eth / end actions l2_decap /
+ mplsoudp_encap / end
-Example:
+IPv6 MPLSoUDP with VLAN outer header::
-.. code-block:: console
+ testpmd> set mplsoudp_encap-with-vlan ip-version ipv6 mask 4 udp-src 5
+ udp-dst 10 ip-src ::1 ip-dst ::2222 vlan-tci 34
+ eth-src 11:11:11:11:11:11 eth-dst 22:22:22:22:22:22
+ testpmd> flow create 0 egress pattern eth / end actions l2_decap /
+ mplsoudp_encap / end
- testpmd> get_5tuple_filter 1 index 0
+Sample MPLSoUDP decapsulation rule
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
- filter[0]:
- Destination IP: 0x02020205 mask: 1
- Source IP: 0x02020204 mask: 1
- Destination Port: 0x0040 mask: 1
- Source Port: 0x0020 mask: 1
- protocol: 0x06 mask: 1
- priority: 3 flags: 0x00 queue: 3
+MPLSoUDP decapsulation outer layer has default value pre-configured in testpmd
+source code, those can be changed by using the following commands
-add_syn_filter
-~~~~~~~~~~~~~~
+IPv4 MPLSoUDP outer header::
-Add SYN filter, which can forward TCP packets whose *SYN* flag is set into a separate queue.
+ testpmd> set mplsoudp_decap ip-version ipv4
+ testpmd> flow create 0 ingress pattern eth / ipv4 / udp / mpls / end actions
+ mplsoudp_decap / l2_encap / end
-add_syn_filter (port_id) priority (high|low) queue (queue_id)
+IPv4 MPLSoUDP with VLAN outer header::
-The available information parameters are:
+ testpmd> set mplsoudp_decap-with-vlan ip-version ipv4
+ testpmd> flow create 0 ingress pattern eth / vlan / ipv4 / udp / mpls / end
+ actions mplsoudp_decap / l2_encap / end
-* port_id: the port which the SYN filter assigned on.
+IPv6 MPLSoUDP outer header::
-* high: this SYN filter has higher priority than other filters.
+ testpmd> set mplsoudp_decap ip-version ipv6
+ testpmd> flow create 0 ingress pattern eth / ipv6 / udp / mpls / end
+ actions mplsoudp_decap / l2_encap / end
-* low: this SYN filter has lower priority than other filters.
+IPv6 MPLSoUDP with VLAN outer header::
-* queue_id: The receive queue associated with this SYN filter
+ testpmd> set mplsoudp_decap-with-vlan ip-version ipv6
+ testpmd> flow create 0 ingress pattern eth / vlan / ipv6 / udp / mpls / end
+ actions mplsoudp_decap / l2_encap / end
-Example:
+Sample Raw encapsulation rule
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
-.. code-block:: console
+Raw encapsulation configuration can be set by the following commands
- testpmd> add_syn_filter 0 priority high queue 3,
+Eecapsulating VxLAN::
-remove_syn_filter
-~~~~~~~~~~~~~~~~~
+ testpmd> set raw_encap 4 eth src is 10:11:22:33:44:55 / vlan tci is 1
+ inner_type is 0x0800 / ipv4 / udp dst is 4789 / vxlan vni
+ is 2 / end_set
+ testpmd> flow create 0 egress pattern eth / ipv4 / end actions
+ raw_encap index 4 / end
-Remove SYN filter
+Sample Raw decapsulation rule
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
-remove_syn_filter (port_id)
+Raw decapsulation configuration can be set by the following commands
-get_syn_filter
-~~~~~~~~~~~~~~
+Decapsulating VxLAN::
-Get and display SYN filter
+ testpmd> set raw_decap eth / ipv4 / udp / vxlan / end_set
+ testpmd> flow create 0 ingress pattern eth / ipv4 / udp / vxlan / eth / ipv4 /
+ end actions raw_decap / queue index 0 / end
-get_syn_filter (port_id)
+Sample ESP rules
+~~~~~~~~~~~~~~~~
-Example:
+ESP rules can be created by the following commands::
-.. code-block:: console
+ testpmd> flow create 0 ingress pattern eth / ipv4 / esp spi is 1 / end actions
+ queue index 3 / end
+ testpmd> flow create 0 ingress pattern eth / ipv4 / udp / esp spi is 1 / end
+ actions queue index 3 / end
+ testpmd> flow create 0 ingress pattern eth / ipv6 / esp spi is 1 / end actions
+ queue index 3 / end
+ testpmd> flow create 0 ingress pattern eth / ipv6 / udp / esp spi is 1 / end
+ actions queue index 3 / end
- testpmd> get_syn_filter 0
+Sample AH rules
+~~~~~~~~~~~~~~~~
- syn filter: on, priority: high, queue: 3
+AH rules can be created by the following commands::
-add_flex_filter
-~~~~~~~~~~~~~~~
+ testpmd> flow create 0 ingress pattern eth / ipv4 / ah spi is 1 / end actions
+ queue index 3 / end
+ testpmd> flow create 0 ingress pattern eth / ipv4 / udp / ah spi is 1 / end
+ actions queue index 3 / end
+ testpmd> flow create 0 ingress pattern eth / ipv6 / ah spi is 1 / end actions
+ queue index 3 / end
+ testpmd> flow create 0 ingress pattern eth / ipv6 / udp / ah spi is 1 / end
+ actions queue index 3 / end
-Add a Flex filter,
-which recognizes any arbitrary pattern within the first 128 bytes of the packet
-and routes packets into one of the receive queues.
+Sample PFCP rules
+~~~~~~~~~~~~~~~~~
-add_flex_filter (port_id) len (len_value) bytes (bytes_string) mask (mask_value)
-priority (prio_value) queue (queue_id) index (idx)
+PFCP rules can be created by the following commands(s_field need to be 1
+if seid is set)::
-The available information parameters are:
+ testpmd> flow create 0 ingress pattern eth / ipv4 / pfcp s_field is 0 / end
+ actions queue index 3 / end
+ testpmd> flow create 0 ingress pattern eth / ipv4 / pfcp s_field is 1
+ seid is 1 / end actions queue index 3 / end
+ testpmd> flow create 0 ingress pattern eth / ipv6 / pfcp s_field is 0 / end
+ actions queue index 3 / end
+ testpmd> flow create 0 ingress pattern eth / ipv6 / pfcp s_field is 1
+ seid is 1 / end actions queue index 3 / end
-* port_id: the port which the Flex filter assigned on.
+BPF Functions
+--------------
-* len_value: filter length in byte, no greater than 128.
+The following sections show functions to load/unload eBPF based filters.
-* bytes_string: a sting in format of octal, means the value the flex filter need to match.
+bpf-load
+~~~~~~~~
-* mask_value: a sting in format of octal, bit 1 means corresponding byte in DWORD participates in the match.
+Load an eBPF program as a callback for particular RX/TX queue::
-* prio_value: the priority of this filter.
+ testpmd> bpf-load rx|tx (portid) (queueid) (load-flags) (bpf-prog-filename)
-* queue_id: The receive queue associated with this Flex filter.
+The available load-flags are:
-* index: the index of this Flex filter
+* ``J``: use JIT generated native code, otherwise BPF interpreter will be used.
-Example:
+* ``M``: assume input parameter is a pointer to rte_mbuf, otherwise assume it is a pointer to first segment's data.
-.. code-block:: console
+* ``-``: none.
- testpmd> add_flex_filter 0 len 16 bytes 0x00000000000000000000000008060000 mask 000C priority 3 queue 3 index 0
+.. note::
-Assign a packet whose 13th and 14th bytes are 0x0806 to queue 3.
+ You'll need clang v3.7 or above to build bpf program you'd like to load
-remove_flex_filter
-~~~~~~~~~~~~~~~~~~
+For example:
-Remove a Flex filter
+.. code-block:: console
-remove_flex_filter (port_id) index (idx)
+ cd examples/bpf
+ clang -O2 -target bpf -c t1.c
-get_flex_filter
-~~~~~~~~~~~~~~~
+Then to load (and JIT compile) t1.o at RX queue 0, port 1:
-Get and display a Flex filter
+.. code-block:: console
-get_flex_filter (port_id) index (idx)
+ testpmd> bpf-load rx 1 0 J ./dpdk.org/examples/bpf/t1.o
-Example:
+To load (not JITed) t1.o at TX queue 0, port 0:
.. code-block:: console
- testpmd> get_flex_filter 0 index 0
+ testpmd> bpf-load tx 0 0 - ./dpdk.org/examples/bpf/t1.o
+
+bpf-unload
+~~~~~~~~~~
- filter[0]:
+Unload previously loaded eBPF program for particular RX/TX queue::
- length: 16
+ testpmd> bpf-unload rx|tx (portid) (queueid)
- dword[]: 0x00000000 00000000 00000000 08060000 00000000 00000000 00000000
- 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
- 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
- 00000000 00000000 00000000 00000000 00000000 00000000 00000000
+For example to unload BPF filter from TX queue 0, port 0:
- mask[]:
- 0b0000000000001100000000000000000000000000000000000000000000000000000000
- 0000000000000000000000000000000000000000000000000000000000
+.. code-block:: console
- priority: 3 queue: 3
+ testpmd> bpf-unload tx 0 0