vxlan
geneve
nvgre
+ vxlan-gpe
show port rss reta
~~~~~~~~~~~~~~~~~~
This is the default mode.
* ``mac``: Changes the source and the destination Ethernet addresses of packets before forwarding them.
- Default application behaviour is to set source Ethernet address to that of the transmitting interface, and destination
+ Default application behavior is to set source Ethernet address to that of the transmitting interface, and destination
address to a dummy value (set during init). The user may specify a target destination Ethernet address via the 'eth-peer' or
'eth-peers-configfile' command-line options. It is not currently possible to specify a specific source Ethernet address.
* ``softnic``: Demonstrates the softnic forwarding operation. In this mode, packet forwarding is
similar to I/O mode except for the fact that packets are loopback to the softnic ports only. Therefore, portmask parameter should be set to softnic port only. The various software based custom NIC pipelines specified through the softnic firmware (DPDK packet framework script) can be tested in this mode. Furthermore, it allows to build 5-level hierarchical QoS scheduler as a default option that can be enabled through CLI once testpmd application is initialised. The user can modify the default scheduler hierarchy or can specify the new QoS Scheduler hierarchy through CLI. Requires ``CONFIG_RTE_LIBRTE_PMD_SOFTNIC=y``.
-* ``noisy``: Noisy neighbour simulation.
+* ``noisy``: Noisy neighbor simulation.
Simulate more realistic behavior of a guest machine engaged in receiving
and sending packets performing Virtual Network Function (VNF).
Add a tunnel filter on a port::
testpmd> tunnel_filter add (port_id) (outer_mac) (inner_mac) (ip_addr) \
- (inner_vlan) (vxlan|nvgre|ipingre) (imac-ivlan|imac-ivlan-tenid|\
+ (inner_vlan) (vxlan|nvgre|ipingre|vxlan-gpe) (imac-ivlan|imac-ivlan-tenid|\
imac-tenid|imac|omac-imac-tenid|oip|iip) (tenant_id) (queue_id)
The available information categories are:
* ``ipingre``: Set tunnel type as IP-in-GRE.
+* ``vxlan-gpe``: Set tunnel type as VXLAN-GPE
+
* ``imac-ivlan``: Set filter type as Inner MAC and VLAN.
* ``imac-ivlan-tenid``: Set filter type as Inner MAC, VLAN and tenant ID.
Remove a tunnel filter on a port::
testpmd> tunnel_filter rm (port_id) (outer_mac) (inner_mac) (ip_addr) \
- (inner_vlan) (vxlan|nvgre|ipingre) (imac-ivlan|imac-ivlan-tenid|\
+ (inner_vlan) (vxlan|nvgre|ipingre|vxlan-gpe) (imac-ivlan|imac-ivlan-tenid|\
imac-tenid|imac|omac-imac-tenid|oip|iip) (tenant_id) (queue_id)
rx_vxlan_port add
udp-dst (udp-dst) ip-tos (ip-tos) ip-ttl (ip-ttl) ip-src (ip-src) \
ip-dst (ip-dst) eth-src (eth-src) eth-dst (eth-dst)
-Those command will set an internal configuration inside testpmd, any following
+These commands will set an internal configuration inside testpmd, any following
flow rule using the action vxlan_encap will use the last configuration set.
To have a different encapsulation header, one of those commands must be called
before the flow rule creation.
set nvgre-with-vlan ip-version (ipv4|ipv6) tni (tni) ip-src (ip-src) \
ip-dst (ip-dst) vlan-tci (vlan-tci) eth-src (eth-src) eth-dst (eth-dst)
-Those command will set an internal configuration inside testpmd, any following
+These commands will set an internal configuration inside testpmd, any following
flow rule using the action nvgre_encap will use the last configuration set.
To have a different encapsulation header, one of those commands must be called
before the flow rule creation.
ip-src (ip-src) ip-dst (ip-dst) vlan-tci (vlan-tci) \
eth-src (eth-src) eth-dst (eth-dst)
-Those command will set an internal configuration inside testpmd, any following
+These commands will set an internal configuration inside testpmd, any following
flow rule using the action mplsogre_encap will use the last configuration set.
To have a different encapsulation header, one of those commands must be called
before the flow rule creation.
set mplsogre_decap ip-version (ipv4|ipv6)
set mplsogre_decap-with-vlan ip-version (ipv4|ipv6)
-Those command will set an internal configuration inside testpmd, any following
+These commands will set an internal configuration inside testpmd, any following
flow rule using the action mplsogre_decap will use the last configuration set.
To have a different decapsulation header, one of those commands must be called
before the flow rule creation.
udp-src (udp-src) udp-dst (udp-dst) ip-src (ip-src) ip-dst (ip-dst) \
vlan-tci (vlan-tci) eth-src (eth-src) eth-dst (eth-dst)
-Those command will set an internal configuration inside testpmd, any following
+These commands will set an internal configuration inside testpmd, any following
flow rule using the action mplsoudp_encap will use the last configuration set.
To have a different encapsulation header, one of those commands must be called
before the flow rule creation.
set mplsoudp_decap ip-version (ipv4|ipv6)
set mplsoudp_decap-with-vlan ip-version (ipv4|ipv6)
-Those command will set an internal configuration inside testpmd, any following
+These commands will set an internal configuration inside testpmd, any following
flow rule using the action mplsoudp_decap will use the last configuration set.
To have a different decapsulation header, one of those commands must be called
before the flow rule creation.
Set the RSS (Receive Side Scaling) mode on or off::
- testpmd> port config all rss (all|default|ip|tcp|udp|sctp|ether|port|vxlan|geneve|nvgre|none)
+ testpmd> port config all rss (all|default|ip|tcp|udp|sctp|ether|port|vxlan|geneve|nvgre|vxlan-gpe|none)
RSS is on by default.
~~~~~~~~~~~~~~~~~~~~~~~~~~~
Add/remove UDP tunnel port for VXLAN/GENEVE tunneling protocols::
- testpmd> port config (port_id) udp_tunnel_port add|rm vxlan|geneve (udp_port)
+ testpmd> port config (port_id) udp_tunnel_port add|rm vxlan|geneve|vxlan-gpe (udp_port)
port config tx_metadata
~~~~~~~~~~~~~~~~~~~~~~~
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Enable dedicated tx/rx queues on bonding devices slaves to handle LACP control plane traffic
-when in mode 4 (link-aggregration-802.3ad)::
+when in mode 4 (link-aggregation-802.3ad)::
testpmd> set bonding lacp dedicated_queues (port_id) (enable|disable)
set bonding agg_mode
~~~~~~~~~~~~~~~~~~~~
-Enable one of the specific aggregators mode when in mode 4 (link-aggregration-802.3ad)::
+Enable one of the specific aggregators mode when in mode 4 (link-aggregation-802.3ad)::
testpmd> set bonding agg_mode (port_id) (bandwidth|count|stable)
* ``shared_shaper_id``: Shared shaper ID to be deleted.
-Set port traffic management hiearchy node private shaper
-~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+Set port traffic management hierarchy node private shaper
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
set the port traffic management hierarchy node private shaper::
Add port traffic management hierarchy nonleaf node
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
-Add nonleaf node to port traffic management hiearchy::
+Add nonleaf node to port traffic management hierarchy::
testpmd> add port tm nonleaf node (port_id) (node_id) (parent_node_id) \
(priority) (weight) (level_id) (shaper_profile_id) \
* ``weight``: Node weight (lowest weight is one). The node weight is relative
to the weight sum of all siblings that have the same priority. It is used by
the WFQ algorithm running on the parent node for scheduling this node.
-* ``level_id``: Hiearchy level of the node.
+* ``level_id``: Hierarchy level of the node.
* ``shaper_profile_id``: Shaper profile ID of the private shaper to be used by
the node.
* ``n_sp_priorities``: Number of strict priorities.
Add port traffic management hierarchy leaf node
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
-Add leaf node to port traffic management hiearchy::
+Add leaf node to port traffic management hierarchy::
testpmd> add port tm leaf node (port_id) (node_id) (parent_node_id) \
(priority) (weight) (level_id) (shaper_profile_id) \
* ``weight``: Node weight (lowest weight is one). The node weight is relative
to the weight sum of all siblings that have the same priority. It is used by
the WFQ algorithm running on the parent node for scheduling this node.
-* ``level_id``: Hiearchy level of the node.
+* ``level_id``: Hierarchy level of the node.
* ``shaper_profile_id``: Shaper profile ID of the private shaper to be used by
the node.
* ``cman_mode``: Congestion management mode to be enabled for this node.
Delete port traffic management hierarchy node
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
-Delete node from port traffic management hiearchy::
+Delete node from port traffic management hierarchy::
testpmd> del port tm node (port_id) (node_id)
- ``sla {MAC-48}``: source Ethernet LLA.
-- ``icmp6_nd_opt_sla_eth``: match ICMPv6 neighbor discovery target Ethernet
+- ``icmp6_nd_opt_tla_eth``: match ICMPv6 neighbor discovery target Ethernet
link-layer address option.
- ``tla {MAC-48}``: target Ethernet LLA.
- ``dec_ttl``: Performs a decrease TTL value action
-- ``set_ttl``: Set TTL value with specificed value
+- ``set_ttl``: Set TTL value with specified value
- ``ttl_value {unsigned}``: The new TTL value to be set
- ``set_mac_src``: set source MAC address
bpf-load
~~~~~~~~
-Load an eBPF program as a callback for partciular RX/TX queue::
+Load an eBPF program as a callback for particular RX/TX queue::
testpmd> bpf-load rx|tx (portid) (queueid) (load-flags) (bpf-prog-filename)
bpf-unload
~~~~~~~~~~
-Unload previously loaded eBPF program for partciular RX/TX queue::
+Unload previously loaded eBPF program for particular RX/TX queue::
testpmd> bpf-unload rx|tx (portid) (queueid)
git.droids-corp.org / dpdk.git / blobdiff