#define FIELD_GET(mask, reg) \
((typeof(mask))(((reg) & (mask)) >> BF_SHF(mask)))
+#define lower_32_bits(x) ((uint32_t)(x))
+#define upper_32_bits(x) ((uint32_t)(((x) >> 16) >> 16))
+
#define PCI_VENDOR_ID_HUAWEI 0x19e5
#define HISI_DMA_DEVICE_ID 0xA122
#define HISI_DMA_PCI_REVISION_ID_REG 0x08
#define HISI_DMA_REVISION_HIP08B 0x21
+#define HISI_DMA_REVISION_HIP09A 0x30
#define HISI_DMA_MAX_HW_QUEUES 4
+#define HISI_DMA_MAX_DESC_NUM 8192
+#define HISI_DMA_MIN_DESC_NUM 32
/**
- * The HIP08B(HiSilicon IP08) and later Chip(e.g. HiSilicon IP09) are DMA iEPs,
- * they have the same pci device id but with different pci revision.
- * Unfortunately, they have different register layouts, so the layout
+ * The HIP08B(HiSilicon IP08) and HIP09B(HiSilicon IP09) are DMA iEPs, they
+ * have the same pci device id but different pci revision.
+ * Unfortunately, they have different register layouts, so two layout
* enumerations are defined.
*/
enum {
HISI_DMA_REG_LAYOUT_INVALID = 0,
- HISI_DMA_REG_LAYOUT_HIP08
+ HISI_DMA_REG_LAYOUT_HIP08,
+ HISI_DMA_REG_LAYOUT_HIP09
};
/**
* calculated by:
* offset = queue-base + (queue-id * queue-region) + reg-offset-in-region.
*
- * The first part of queue region is basically the same for HIP08 and later chip
+ * The first part of queue region is basically the same for HIP08 and HIP09
* register layouts, therefore, HISI_QUEUE_* registers are defined for it.
*/
#define HISI_DMA_QUEUE_SQ_BASE_L_REG 0x0
#define HISI_DMA_QUEUE_FSM_REG 0x30
#define HISI_DMA_QUEUE_FSM_STS_M GENMASK(3, 0)
#define HISI_DMA_QUEUE_INT_STATUS_REG 0x40
+#define HISI_DMA_QUEUE_INT_MASK_REG 0x44
#define HISI_DMA_QUEUE_ERR_INT_NUM0_REG 0x84
#define HISI_DMA_QUEUE_ERR_INT_NUM1_REG 0x88
#define HISI_DMA_QUEUE_ERR_INT_NUM2_REG 0x8C
*/
#define HISI_DMA_HIP08_QUEUE_BASE 0x0
#define HISI_DMA_HIP08_QUEUE_CTRL0_ERR_ABORT_B 2
-#define HISI_DMA_HIP08_QUEUE_INT_MASK_REG 0x44
#define HISI_DMA_HIP08_QUEUE_INT_MASK_M GENMASK(14, 0)
#define HISI_DMA_HIP08_QUEUE_ERR_INT_NUM3_REG 0x90
#define HISI_DMA_HIP08_QUEUE_ERR_INT_NUM4_REG 0x94
#define HISI_DMA_HIP08_DUMP_START_REG 0x2000
#define HISI_DMA_HIP08_DUMP_END_REG 0x2280
+/**
+ * HiSilicon IP09 DMA register and field define:
+ */
+#define HISI_DMA_HIP09_QUEUE_BASE 0x2000
+#define HISI_DMA_HIP09_QUEUE_CTRL0_ERR_ABORT_M GENMASK(31, 28)
+#define HISI_DMA_HIP09_QUEUE_CTRL1_VA_ENABLE_B 2
+#define HISI_DMA_HIP09_QUEUE_INT_MASK_M 0x1
+#define HISI_DMA_HIP09_QUEUE_ERR_INT_STATUS_REG 0x48
+#define HISI_DMA_HIP09_QUEUE_ERR_INT_MASK_REG 0x4C
+#define HISI_DMA_HIP09_QUEUE_ERR_INT_MASK_M GENMASK(18, 1)
+#define HISI_DMA_HIP09_QUEUE_CFG_REG(queue_id) (0x800 + \
+ (queue_id) * 0x20)
+#define HISI_DMA_HIP09_QUEUE_CFG_LINK_DOWN_MASK_B 16
+#define HISI_DMA_HIP09_DUMP_REGION_A_START_REG 0x0
+#define HISI_DMA_HIP09_DUMP_REGION_A_END_REG 0x368
+#define HISI_DMA_HIP09_DUMP_REGION_B_START_REG 0x800
+#define HISI_DMA_HIP09_DUMP_REGION_B_END_REG 0xA08
+#define HISI_DMA_HIP09_DUMP_REGION_C_START_REG 0x1800
+#define HISI_DMA_HIP09_DUMP_REGION_C_END_REG 0x1A4C
+#define HISI_DMA_HIP09_DUMP_REGION_D_START_REG 0x1C00
+#define HISI_DMA_HIP09_DUMP_REGION_D_END_REG 0x1CC4
+
/**
* In fact, there are multiple states, but it need to pay attention to
- * the following two states for the driver:
+ * the following three states for the driver:
*/
enum {
HISI_DMA_STATE_IDLE = 0,
HISI_DMA_STATE_RUN,
+ /**
+ * All of the submitted descriptor are finished, and the queue
+ * is waiting for new descriptors.
+ */
+ HISI_DMA_STATE_CPL,
+};
+
+/**
+ * Hardware complete status define:
+ */
+#define HISI_DMA_STATUS_SUCCESS 0x0
+#define HISI_DMA_STATUS_INVALID_OPCODE 0x1
+#define HISI_DMA_STATUS_INVALID_LENGTH 0x2
+#define HISI_DMA_STATUS_USER_ABORT 0x4
+#define HISI_DMA_STATUS_REMOTE_READ_ERROR 0x10
+#define HISI_DMA_STATUS_AXI_READ_ERROR 0x20
+#define HISI_DMA_STATUS_AXI_WRITE_ERROR 0x40
+#define HISI_DMA_STATUS_DATA_POISON 0x80
+#define HISI_DMA_STATUS_SQE_READ_ERROR 0x100
+#define HISI_DMA_STATUS_SQE_READ_POISION 0x200
+#define HISI_DMA_STATUS_REMOTE_DATA_POISION 0x400
+#define HISI_DMA_STATUS_LINK_DOWN_ERROR 0x800
+
+/**
+ * After scanning the CQ array, the CQ head register needs to be updated.
+ * Updating the register involves write memory barrier operations.
+ * Here use the following method to reduce WMB operations:
+ * a) malloc more CQEs, which correspond to the macro HISI_DMA_CQ_RESERVED.
+ * b) update the CQ head register after accumulated number of completed CQs
+ * is greater than or equal to HISI_DMA_CQ_RESERVED.
+ */
+#define HISI_DMA_CQ_RESERVED 64
+
+struct hisi_dma_sqe {
+ uint32_t dw0;
+#define SQE_FENCE_FLAG BIT(10)
+#define SQE_OPCODE_M2M 0x4
+ uint32_t dw1;
+ uint32_t dw2;
+ uint32_t length;
+ uint64_t src_addr;
+ uint64_t dst_addr;
+};
+
+struct hisi_dma_cqe {
+ uint64_t rsv;
+ uint64_t misc;
+#define CQE_SQ_HEAD_MASK GENMASK(15, 0)
+#define CQE_VALID_B BIT(48)
+#define CQE_STATUS_MASK GENMASK(63, 49)
};
struct hisi_dma_dev {
+ struct hisi_dma_sqe *sqe;
+ volatile struct hisi_dma_cqe *cqe;
+ uint16_t *status; /* the completion status array of SQEs. */
+
+ volatile void *sq_tail_reg; /**< register address for doorbell. */
+ volatile void *cq_head_reg; /**< register address for answer CQ. */
+
+ uint16_t sq_depth_mask; /**< SQ depth - 1, the SQ depth is power of 2 */
+ uint16_t cq_depth; /* CQ depth */
+
+ uint16_t ridx; /**< ring index which will assign to the next request. */
+ /** ring index which returned by hisi_dmadev_completed APIs. */
+ uint16_t cridx;
+
+ /**
+ * SQE array management fields:
+ *
+ * -----------------------------------------------------
+ * | SQE0 | SQE1 | SQE2 | ... | SQEx | ... | SQEn-1 |
+ * -----------------------------------------------------
+ * ^ ^ ^
+ * | | |
+ * sq_head cq_sq_head sq_tail
+ *
+ * sq_head: index to the oldest completed request, this filed was
+ * updated by hisi_dmadev_completed* APIs.
+ * sq_tail: index of the next new request, this field was updated by
+ * hisi_dmadev_copy API.
+ * cq_sq_head: next index of index that has been completed by hardware,
+ * this filed was updated by hisi_dmadev_completed* APIs.
+ *
+ * [sq_head, cq_sq_head): the SQEs that hardware already completed.
+ * [cq_sq_head, sq_tail): the SQEs that hardware processing.
+ */
+ uint16_t sq_head;
+ uint16_t sq_tail;
+ uint16_t cq_sq_head;
+ /**
+ * The driver scans the CQE array, if the valid bit changes, the CQE is
+ * considered valid.
+ * Note: One CQE is corresponding to one or several SQEs, e.g. app
+ * submits two copy requests, the hardware processes the two SQEs,
+ * but it may write back only one CQE and the CQE's sq_head field
+ * indicates the index of the second copy request in the SQE
+ * array.
+ */
+ uint16_t cq_head; /**< CQ index for next scans. */
+ /** accumulated number of completed CQs
+ * @see HISI_DMA_CQ_RESERVED
+ */
+ uint16_t cqs_completed;
+ uint8_t cqe_vld; /**< valid bit for CQE, will change for every round. */
+
+ uint64_t submitted;
+ uint64_t completed;
+ uint64_t errors;
+ uint64_t qfulls;
+
+ /**
+ * The following fields are not accessed in the I/O path, so they are
+ * placed at the end.
+ */
struct rte_dma_dev_data *data;
uint8_t revision; /**< PCI revision. */
uint8_t reg_layout; /**< hardware register layout. */
void *io_base;
uint8_t queue_id; /**< hardware DMA queue index. */
+ const struct rte_memzone *iomz;
+ uint32_t iomz_sz;
+ rte_iova_t sqe_iova;
+ rte_iova_t cqe_iova;
};
#endif /* HISI_DMADEV_H */
git.droids-corp.org / dpdk.git / blobdiff