net/qede/base: fix macros to check chip revision/metal

[dpdk.git] / drivers / net / bnxt / hsi_struct_def_dpdk.h

diff --git a/drivers/net/bnxt/hsi_struct_def_dpdk.h b/drivers/net/bnxt/hsi_struct_def_dpdk.h
index c2335d0..cb8660a 100644 (file)
--- a/drivers/net/bnxt/hsi_struct_def_dpdk.h
+++ b/drivers/net/bnxt/hsi_struct_def_dpdk.h
@@ -123,7 +123,7 @@
 #define HWRM_CFA_L2_FILTER_CFG         (UINT32_C(0x92))
 #define HWRM_CFA_L2_SET_RX_MASK                (UINT32_C(0x93))
     /* Reserved for future use */
-#define RESERVED4                      (UINT32_C(0x94))
+#define HWRM_CFA_VLAN_ANTISPOOF_CFG    (UINT32_C(0x94))
 #define HWRM_CFA_TUNNEL_FILTER_ALLOC   (UINT32_C(0x95))
 #define HWRM_CFA_TUNNEL_FILTER_FREE    (UINT32_C(0x96))
 #define HWRM_CFA_NTUPLE_FILTER_ALLOC   (UINT32_C(0x99))
@@ -3190,6 +3190,15 @@ struct hwrm_func_cfg_input {
         * command will be persistent over warm boot.
         */
        #define HWRM_FUNC_CFG_INPUT_FLAGS_VIRT_MAC_PERSIST      UINT32_C(0x800)
+       /*
+        * This bit only applies to the VF. If this bit is set, the
+        * statistic context counters will not be cleared when the
+        * statistic context is freed or a function reset is called on
+        * VF. This bit will be cleared when the PF is unloaded or a
+        * function reset is called on the PF.
+        */
+       #define HWRM_FUNC_CFG_INPUT_FLAGS_NO_AUTOCLEAR_STATISTIC        \
+               UINT32_C(0x1000)
        uint32_t enables;
        /* This bit must be '1' for the mtu field to be configured. */
        #define HWRM_FUNC_CFG_INPUT_ENABLES_MTU UINT32_C(0x1)
@@ -9462,6 +9471,85 @@ struct hwrm_cfa_l2_set_rx_mask_output {
         */
 } __attribute__((packed));
 
+/* hwrm_cfa_vlan_antispoof_cfg */
+/* Description: Configures vlan anti-spoof filters for VF. */
+/* Input (32 bytes) */
+struct hwrm_cfa_vlan_antispoof_cfg_input {
+       uint16_t req_type;
+       /*
+        * This value indicates what type of request this is. The format for the
+        * rest of the command is determined by this field.
+        */
+       uint16_t cmpl_ring;
+       /*
+        * This value indicates the what completion ring the request will be
+        * optionally completed on. If the value is -1, then no CR completion
+        * will be generated. Any other value must be a valid CR ring_id value
+        * for this function.
+        */
+       uint16_t seq_id;
+       /* This value indicates the command sequence number. */
+       uint16_t target_id;
+       /*
+        * Target ID of this command. 0x0 - 0xFFF8 - Used for function ids
+        * 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF - HWRM
+        */
+       uint64_t resp_addr;
+       /*
+        * This is the host address where the response will be written when the
+        * request is complete. This area must be 16B aligned and must be
+        * cleared to zero before the request is made.
+        */
+       uint16_t fid;
+       /*
+        * Function ID of the function that is being configured. Only valid for
+        * a VF FID configured by the PF.
+        */
+       uint8_t unused_0;
+       uint8_t unused_1;
+       uint32_t num_vlan_entries;
+       /* Number of VLAN entries in the vlan_tag_mask_tbl. */
+       uint64_t vlan_tag_mask_tbl_addr;
+       /*
+        * The vlan_tag_mask_tbl_addr is the DMA address of the VLAN antispoof
+        * table. Each table entry contains the 16-bit TPID (0x8100 or 0x88a8
+        * only), 16-bit VLAN ID, and a 16-bit mask, all in network order to
+        * match hwrm_cfa_l2_set_rx_mask. For an individual VLAN entry, the mask
+        * value should be 0xfff for the 12-bit VLAN ID.
+        */
+};
+
+/* Output (16 bytes) */
+struct hwrm_cfa_vlan_antispoof_cfg_output {
+       uint16_t error_code;
+       /*
+        * Pass/Fail or error type Note: receiver to verify the in parameters,
+        * and fail the call with an error when appropriate
+        */
+       uint16_t req_type;
+       /* This field returns the type of original request. */
+       uint16_t seq_id;
+       /* This field provides original sequence number of the command. */
+       uint16_t resp_len;
+       /*
+        * This field is the length of the response in bytes. The last byte of
+        * the response is a valid flag that will read as '1' when the command
+        * has been completely written to memory.
+        */
+       uint32_t unused_0;
+       uint8_t unused_1;
+       uint8_t unused_2;
+       uint8_t unused_3;
+       uint8_t valid;
+       /*
+        * This field is used in Output records to indicate that the output is
+        * completely written to RAM. This field should be read as '1' to
+        * indicate that the output has been completely written. When writing a
+        * command completion or response to an internal processor, the order of
+        * writes has to be such that this field is written last.
+        */
+};
+
 /* hwrm_tunnel_dst_port_query */
 /*
  * Description: This function is called by a driver to query tunnel type