uint8_t valid;
} __attribute__((packed));
+/* hwrm_cfa_l2_set_rx_mask */
+/* Description: This command will set rx mask of the function. */
+
+/* Input (40 bytes) */
+struct hwrm_cfa_l2_set_rx_mask_input {
+ /*
+ * This value indicates what type of request this is. The format for the
+ * rest of the command is determined by this field.
+ */
+ uint16_t req_type;
+
+ /*
+ * This value indicates the what completion ring the request will be
+ * optionally completed on. If the value is -1, then no CR completion
+ * will be generated. Any other value must be a valid CR ring_id value
+ * for this function.
+ */
+ uint16_t cmpl_ring;
+
+ /* This value indicates the command sequence number. */
+ uint16_t seq_id;
+
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function ids
+ * 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+
+ /*
+ * This is the host address where the response will be written when the
+ * request is complete. This area must be 16B aligned and must be
+ * cleared to zero before the request is made.
+ */
+ uint64_t resp_addr;
+
+ /* VNIC ID */
+ uint32_t vnic_id;
+
+ /* Reserved for future use. */
+ #define HWRM_CFA_L2_SET_RX_MASK_INPUT_MASK_RESERVED UINT32_C(0x1)
+ /*
+ * When this bit is '1', the function is requested to accept multi-cast
+ * packets specified by the multicast addr table.
+ */
+ #define HWRM_CFA_L2_SET_RX_MASK_INPUT_MASK_MCAST UINT32_C(0x2)
+ /*
+ * When this bit is '1', the function is requested to accept all multi-
+ * cast packets.
+ */
+ #define HWRM_CFA_L2_SET_RX_MASK_INPUT_MASK_ALL_MCAST UINT32_C(0x4)
+ /*
+ * When this bit is '1', the function is requested to accept broadcast
+ * packets.
+ */
+ #define HWRM_CFA_L2_SET_RX_MASK_INPUT_MASK_BCAST UINT32_C(0x8)
+ /*
+ * When this bit is '1', the function is requested to be put in the
+ * promiscuous mode. The HWRM should accept any function to set up
+ * promiscuous mode. The HWRM shall follow the semantics below for the
+ * promiscuous mode support. # When partitioning is not enabled on a
+ * port (i.e. single PF on the port), then the PF shall be allowed to be
+ * in the promiscuous mode. When the PF is in the promiscuous mode, then
+ * it shall receive all host bound traffic on that port. # When
+ * partitioning is enabled on a port (i.e. multiple PFs per port) and a
+ * PF on that port is in the promiscuous mode, then the PF receives all
+ * traffic within that partition as identified by a unique identifier
+ * for the PF (e.g. S-Tag). If a unique outer VLAN for the PF is
+ * specified, then the setting of promiscuous mode on that PF shall
+ * result in the PF receiving all host bound traffic with matching outer
+ * VLAN. # A VF shall can be set in the promiscuous mode. In the
+ * promiscuous mode, the VF does not receive any traffic unless a unique
+ * outer VLAN for the VF is specified. If a unique outer VLAN for the VF
+ * is specified, then the setting of promiscuous mode on that VF shall
+ * result in the VF receiving all host bound traffic with the matching
+ * outer VLAN. # The HWRM shall allow the setting of promiscuous mode on
+ * a function independently from the promiscuous mode settings on other
+ * functions.
+ */
+ #define HWRM_CFA_L2_SET_RX_MASK_INPUT_MASK_PROMISCUOUS UINT32_C(0x10)
+ /*
+ * If this flag is set, the corresponding RX filters shall be set up to
+ * cover multicast/broadcast filters for the outermost Layer 2
+ * destination MAC address field.
+ */
+ #define HWRM_CFA_L2_SET_RX_MASK_INPUT_MASK_OUTERMOST UINT32_C(0x20)
+ uint32_t mask;
+
+ /* This is the address for mcast address tbl. */
+ uint64_t mc_tbl_addr;
+
+ /*
+ * This value indicates how many entries in mc_tbl are valid. Each entry
+ * is 6 bytes.
+ */
+ uint32_t num_mc_entries;
+
+ uint32_t unused_0;
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_cfa_l2_set_rx_mask_output {
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in parameters,
+ * and fail the call with an error when appropriate
+ */
+ uint16_t error_code;
+
+ /* This field returns the type of original request. */
+ uint16_t req_type;
+
+ /* This field provides original sequence number of the command. */
+ uint16_t seq_id;
+
+ /*
+ * This field is the length of the response in bytes. The last byte of
+ * the response is a valid flag that will read as '1' when the command
+ * has been completely written to memory.
+ */
+ uint16_t resp_len;
+
+ uint32_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+
+ /*
+ * This field is used in Output records to indicate that the output is
+ * completely written to RAM. This field should be read as '1' to
+ * indicate that the output has been completely written. When writing a
+ * command completion or response to an internal processor, the order of
+ * writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __attribute__((packed));
+
/* hwrm_exec_fwd_resp */
/*
* Description: This command is used to send an encapsulated request to the
git.droids-corp.org / dpdk.git / blobdiff