};
struct hns3_rx_queue {
- void *io_base;
volatile void *io_head_reg;
- struct hns3_adapter *hns;
struct hns3_ptype_table *ptype_tbl;
struct rte_mempool *mb_pool;
struct hns3_desc *rx_ring;
- uint64_t rx_ring_phys_addr; /* RX ring DMA address */
- const struct rte_memzone *mz;
struct hns3_entry *sw_ring;
- struct rte_mbuf *pkt_first_seg;
- struct rte_mbuf *pkt_last_seg;
- uint16_t queue_id;
uint16_t port_id;
uint16_t nb_rx_desc;
- uint16_t rx_buf_len;
/*
* threshold for the number of BDs waited to passed to hardware. If the
* number exceeds the threshold, driver will pass these BDs to hardware.
/* 4 if DEV_RX_OFFLOAD_KEEP_CRC offload set, 0 otherwise */
uint8_t crc_len;
- bool rx_deferred_start; /* don't start this queue in dev start */
- bool configured; /* indicate if rx queue has been configured */
/*
* Indicate whether ignore the outer VLAN field in the Rx BD reported
* by the Hardware. Because the outer VLAN is the PVID if the PVID is
* driver does not need to perform PVID-related operation in Rx. At this
* point, the pvid_sw_discard_en will be false.
*/
- bool pvid_sw_discard_en;
- bool ptype_en; /* indicate if the ptype field enabled */
- bool enabled; /* indicate if Rx queue has been enabled */
+ uint8_t pvid_sw_discard_en:1;
+ uint8_t ptype_en:1; /* indicate if the ptype field enabled */
+
+ uint64_t mbuf_initializer; /* value to init mbufs used with vector rx */
+ /* offset_table: used for vector, to solve execute re-order problem */
+ uint8_t offset_table[HNS3_VECTOR_RX_OFFSET_TABLE_LEN + 1];
+
+ uint16_t bulk_mbuf_num; /* indicate bulk_mbuf valid nums */
struct hns3_rx_basic_stats basic_stats;
+
+ struct rte_mbuf *pkt_first_seg;
+ struct rte_mbuf *pkt_last_seg;
+
+ struct rte_mbuf *bulk_mbuf[HNS3_BULK_ALLOC_MBUF_NUM];
+
/* DFX statistics that driver does not need to discard packets */
struct hns3_rx_dfx_stats dfx_stats;
/* Error statistics that driver needs to discard packets */
struct hns3_rx_bd_errors_stats err_stats;
- struct rte_mbuf *bulk_mbuf[HNS3_BULK_ALLOC_MBUF_NUM];
- uint16_t bulk_mbuf_num;
-
- /* offset_table: used for vector, to solve execute re-order problem */
- uint8_t offset_table[HNS3_VECTOR_RX_OFFSET_TABLE_LEN + 1];
- uint64_t mbuf_initializer; /* value to init mbufs used with vector rx */
struct rte_mbuf fake_mbuf; /* fake mbuf used with vector rx */
+
+
+ /*
+ * The following fields are not accessed in the I/O path, so they are
+ * placed at the end.
+ */
+ void *io_base;
+ struct hns3_adapter *hns;
+ uint64_t rx_ring_phys_addr; /* RX ring DMA address */
+ const struct rte_memzone *mz;
+
+ uint16_t queue_id;
+ uint16_t rx_buf_len;
+
+ bool configured; /* indicate if rx queue has been configured */
+ bool rx_deferred_start; /* don't start this queue in dev start */
+ bool enabled; /* indicate if Rx queue has been enabled */
};
struct hns3_tx_basic_stats {
};
struct hns3_tx_queue {
- void *io_base;
volatile void *io_tail_reg;
- struct hns3_adapter *hns;
struct hns3_desc *tx_ring;
- uint64_t tx_ring_phys_addr; /* TX ring DMA address */
- const struct rte_memzone *mz;
struct hns3_entry *sw_ring;
- uint16_t queue_id;
- uint16_t port_id;
uint16_t nb_tx_desc;
/*
* index of next BD whose corresponding rte_mbuf can be released by
uint16_t tx_free_thresh;
/*
- * For better performance in tx datapath, releasing mbuf in batches is
- * required.
- * Only checking the VLD bit of the last descriptor in a batch of the
- * thresh descriptors does not mean that these descriptors are all sent
- * by hardware successfully. So we need to check that the VLD bits of
- * all descriptors are cleared. and then free all mbufs in the batch.
- * - tx_rs_thresh
- * Number of mbufs released at a time.
- *
- * - free
- * Tx mbuf free array used for preserving temporarily address of mbuf
- * released back to mempool, when releasing mbuf in batches.
+ * The minimum length of the packet supported by hardware in the Tx
+ * direction.
*/
- uint16_t tx_rs_thresh;
- struct rte_mbuf **free;
+ uint8_t min_tx_pkt_len;
+
+ uint8_t max_non_tso_bd_num; /* max BD number of one non-TSO packet */
/*
* tso mode.
* checksum of packets that need TSO, so network driver software
* not need to recalculate it.
*/
- uint8_t tso_mode;
+ uint16_t tso_mode:1;
/*
* udp checksum mode.
* value range:
* In this mode, HW does not have the preceding problems and can
* directly calculate the checksum of these UDP packets.
*/
- uint8_t udp_cksum_mode;
- /*
- * The minimum length of the packet supported by hardware in the Tx
- * direction.
- */
- uint32_t min_tx_pkt_len;
+ uint16_t udp_cksum_mode:1;
- uint8_t max_non_tso_bd_num; /* max BD number of one non-TSO packet */
- bool tx_deferred_start; /* don't start this queue in dev start */
- bool configured; /* indicate if tx queue has been configured */
+ uint16_t simple_bd_enable:1;
+ uint16_t tx_push_enable:1; /* check whether the tx push is enabled */
/*
* Indicate whether add the vlan_tci of the mbuf to the inner VLAN field
* of Tx BD. Because the outer VLAN will always be the PVID when the
* PVID-related operations in Tx. And pvid_sw_shift_en will be false at
* this point.
*/
- bool pvid_sw_shift_en;
- bool enabled; /* indicate if Tx queue has been enabled */
+ uint16_t pvid_sw_shift_en:1;
+
+ /*
+ * For better performance in tx datapath, releasing mbuf in batches is
+ * required.
+ * Only checking the VLD bit of the last descriptor in a batch of the
+ * thresh descriptors does not mean that these descriptors are all sent
+ * by hardware successfully. So we need to check that the VLD bits of
+ * all descriptors are cleared. and then free all mbufs in the batch.
+ * - tx_rs_thresh
+ * Number of mbufs released at a time.
+ *
+ * - free
+ * Tx mbuf free array used for preserving temporarily address of mbuf
+ * released back to mempool, when releasing mbuf in batches.
+ */
+ uint16_t tx_rs_thresh;
+ struct rte_mbuf **free;
struct hns3_tx_basic_stats basic_stats;
struct hns3_tx_dfx_stats dfx_stats;
+
+
+ /*
+ * The following fields are not accessed in the I/O path, so they are
+ * placed at the end.
+ */
+ void *io_base;
+ struct hns3_adapter *hns;
+ uint64_t tx_ring_phys_addr; /* TX ring DMA address */
+ const struct rte_memzone *mz;
+
+ uint16_t port_id;
+ uint16_t queue_id;
+
+ bool configured; /* indicate if tx queue has been configured */
+ bool tx_deferred_start; /* don't start this queue in dev start */
+ bool enabled; /* indicate if Tx queue has been enabled */
};
#define HNS3_GET_TX_QUEUE_PEND_BD_NUM(txq) \
git.droids-corp.org / dpdk.git / blobdiff