/*******************************************************************************
-Copyright (c) 2001-2014, Intel Corporation
+Copyright (c) 2001-2015, Intel Corporation
All rights reserved.
Redistribution and use in source and binary forms, with or without
if (hw->phy.multispeed_fiber) {
/* Set up dual speed SFP+ support */
mac->ops.setup_link = ixgbe_setup_mac_link_multispeed_fiber;
+ mac->ops.setup_mac_link = ixgbe_setup_mac_link_82599;
+ mac->ops.set_rate_select_speed =
+ ixgbe_set_hard_rate_select_speed;
} else {
if ((ixgbe_get_media_type(hw) == ixgbe_media_type_backplane) &&
(hw->phy.smart_speed == ixgbe_smart_speed_auto ||
mac->max_tx_queues = IXGBE_82599_MAX_TX_QUEUES;
mac->max_msix_vectors = ixgbe_get_pcie_msix_count_generic(hw);
- mac->arc_subsystem_valid = (IXGBE_READ_REG(hw, IXGBE_FWSM) &
- IXGBE_FWSM_MODE_MASK) ? true : false;
+ mac->arc_subsystem_valid = !!(IXGBE_READ_REG(hw, IXGBE_FWSM_BY_MAC(hw))
+ & IXGBE_FWSM_MODE_MASK);
hw->mbx.ops.init_params = ixgbe_init_mbx_params_pf;
}
}
-
/**
- * ixgbe_setup_mac_link_multispeed_fiber - Set MAC link speed
+ * ixgbe_set_hard_rate_select_speed - Set module link speed
* @hw: pointer to hardware structure
- * @speed: new link speed
- * @autoneg_wait_to_complete: true when waiting for completion is needed
+ * @speed: link speed to set
*
- * Set the link speed in the AUTOC register and restarts link.
- **/
-s32 ixgbe_setup_mac_link_multispeed_fiber(struct ixgbe_hw *hw,
- ixgbe_link_speed speed,
- bool autoneg_wait_to_complete)
+ * Set module link speed via RS0/RS1 rate select pins.
+ */
+void ixgbe_set_hard_rate_select_speed(struct ixgbe_hw *hw,
+ ixgbe_link_speed speed)
{
- s32 status = IXGBE_SUCCESS;
- ixgbe_link_speed link_speed = IXGBE_LINK_SPEED_UNKNOWN;
- ixgbe_link_speed highest_link_speed = IXGBE_LINK_SPEED_UNKNOWN;
- u32 speedcnt = 0;
u32 esdp_reg = IXGBE_READ_REG(hw, IXGBE_ESDP);
- u32 i = 0;
- bool autoneg, link_up = false;
-
- DEBUGFUNC("ixgbe_setup_mac_link_multispeed_fiber");
-
- /* Mask off requested but non-supported speeds */
- status = ixgbe_get_link_capabilities(hw, &link_speed, &autoneg);
- if (status != IXGBE_SUCCESS)
- return status;
-
- speed &= link_speed;
-
- /*
- * Try each speed one by one, highest priority first. We do this in
- * software because 10gb fiber doesn't support speed autonegotiation.
- */
- if (speed & IXGBE_LINK_SPEED_10GB_FULL) {
- speedcnt++;
- highest_link_speed = IXGBE_LINK_SPEED_10GB_FULL;
-
- /* If we already have link at this speed, just jump out */
- status = ixgbe_check_link(hw, &link_speed, &link_up, false);
- if (status != IXGBE_SUCCESS)
- return status;
-
- if ((link_speed == IXGBE_LINK_SPEED_10GB_FULL) && link_up)
- goto out;
-
- /* Set the module link speed */
- switch (hw->phy.media_type) {
- case ixgbe_media_type_fiber:
- esdp_reg |= (IXGBE_ESDP_SDP5_DIR | IXGBE_ESDP_SDP5);
- IXGBE_WRITE_REG(hw, IXGBE_ESDP, esdp_reg);
- IXGBE_WRITE_FLUSH(hw);
- break;
- case ixgbe_media_type_fiber_qsfp:
- /* QSFP module automatically detects MAC link speed */
- break;
- default:
- DEBUGOUT("Unexpected media type.\n");
- break;
- }
-
- /* Allow module to change analog characteristics (1G->10G) */
- msec_delay(40);
-
- status = ixgbe_setup_mac_link_82599(hw,
- IXGBE_LINK_SPEED_10GB_FULL,
- autoneg_wait_to_complete);
- if (status != IXGBE_SUCCESS)
- return status;
-
- /* Flap the tx laser if it has not already been done */
- ixgbe_flap_tx_laser(hw);
-
- /*
- * Wait for the controller to acquire link. Per IEEE 802.3ap,
- * Section 73.10.2, we may have to wait up to 500ms if KR is
- * attempted. 82599 uses the same timing for 10g SFI.
- */
- for (i = 0; i < 5; i++) {
- /* Wait for the link partner to also set speed */
- msec_delay(100);
-
- /* If we have link, just jump out */
- status = ixgbe_check_link(hw, &link_speed,
- &link_up, false);
- if (status != IXGBE_SUCCESS)
- return status;
-
- if (link_up)
- goto out;
- }
- }
-
- if (speed & IXGBE_LINK_SPEED_1GB_FULL) {
- speedcnt++;
- if (highest_link_speed == IXGBE_LINK_SPEED_UNKNOWN)
- highest_link_speed = IXGBE_LINK_SPEED_1GB_FULL;
-
- /* If we already have link at this speed, just jump out */
- status = ixgbe_check_link(hw, &link_speed, &link_up, false);
- if (status != IXGBE_SUCCESS)
- return status;
-
- if ((link_speed == IXGBE_LINK_SPEED_1GB_FULL) && link_up)
- goto out;
-
- /* Set the module link speed */
- switch (hw->phy.media_type) {
- case ixgbe_media_type_fiber:
- esdp_reg &= ~IXGBE_ESDP_SDP5;
- esdp_reg |= IXGBE_ESDP_SDP5_DIR;
- IXGBE_WRITE_REG(hw, IXGBE_ESDP, esdp_reg);
- IXGBE_WRITE_FLUSH(hw);
- break;
- case ixgbe_media_type_fiber_qsfp:
- /* QSFP module automatically detects link speed */
- break;
- default:
- DEBUGOUT("Unexpected media type.\n");
- break;
- }
-
- /* Allow module to change analog characteristics (10G->1G) */
- msec_delay(40);
-
- status = ixgbe_setup_mac_link_82599(hw,
- IXGBE_LINK_SPEED_1GB_FULL,
- autoneg_wait_to_complete);
- if (status != IXGBE_SUCCESS)
- return status;
-
- /* Flap the Tx laser if it has not already been done */
- ixgbe_flap_tx_laser(hw);
-
- /* Wait for the link partner to also set speed */
- msec_delay(100);
- /* If we have link, just jump out */
- status = ixgbe_check_link(hw, &link_speed, &link_up, false);
- if (status != IXGBE_SUCCESS)
- return status;
-
- if (link_up)
- goto out;
+ switch (speed) {
+ case IXGBE_LINK_SPEED_10GB_FULL:
+ esdp_reg |= (IXGBE_ESDP_SDP5_DIR | IXGBE_ESDP_SDP5);
+ break;
+ case IXGBE_LINK_SPEED_1GB_FULL:
+ esdp_reg &= ~IXGBE_ESDP_SDP5;
+ esdp_reg |= IXGBE_ESDP_SDP5_DIR;
+ break;
+ default:
+ DEBUGOUT("Invalid fixed module speed\n");
+ return;
}
- /*
- * We didn't get link. Configure back to the highest speed we tried,
- * (if there was more than one). We call ourselves back with just the
- * single highest speed that the user requested.
- */
- if (speedcnt > 1)
- status = ixgbe_setup_mac_link_multispeed_fiber(hw,
- highest_link_speed, autoneg_wait_to_complete);
-
-out:
- /* Set autoneg_advertised value based on input link speed */
- hw->phy.autoneg_advertised = 0;
-
- if (speed & IXGBE_LINK_SPEED_10GB_FULL)
- hw->phy.autoneg_advertised |= IXGBE_LINK_SPEED_10GB_FULL;
-
- if (speed & IXGBE_LINK_SPEED_1GB_FULL)
- hw->phy.autoneg_advertised |= IXGBE_LINK_SPEED_1GB_FULL;
-
- return status;
+ IXGBE_WRITE_REG(hw, IXGBE_ESDP, esdp_reg);
+ IXGBE_WRITE_FLUSH(hw);
}
/**
/* Add the SAN MAC address to the RAR only if it's a valid address */
if (ixgbe_validate_mac_addr(hw->mac.san_addr) == 0) {
- hw->mac.ops.set_rar(hw, hw->mac.num_rar_entries - 1,
- hw->mac.san_addr, 0, IXGBE_RAH_AV);
-
/* Save the SAN MAC RAR index */
hw->mac.san_mac_rar_index = hw->mac.num_rar_entries - 1;
+ hw->mac.ops.set_rar(hw, hw->mac.san_mac_rar_index,
+ hw->mac.san_addr, 0, IXGBE_RAH_AV);
+
+ /* clear VMDq pool/queue selection for this RAR */
+ hw->mac.ops.clear_vmdq(hw, hw->mac.san_mac_rar_index,
+ IXGBE_CLEAR_VMDQ_ALL);
+
/* Reserve the last RAR for the SAN MAC address */
hw->mac.num_rar_entries--;
}
* Continue setup of fdirctrl register bits:
* Turn perfect match filtering on
* Report hash in RSS field of Rx wb descriptor
- * Initialize the drop queue
+ * Initialize the drop queue to queue 127
* Move the flexible bytes to use the ethertype - shift 6 words
* Set the maximum length per hash bucket to 0xA filters
* Send interrupt when 64 (0x4 * 16) filters are left
return IXGBE_SUCCESS;
}
+/**
+ * ixgbe_set_fdir_drop_queue_82599 - Set Flow Director drop queue
+ * @hw: pointer to hardware structure
+ * @dropqueue: Rx queue index used for the dropped packets
+ **/
+void ixgbe_set_fdir_drop_queue_82599(struct ixgbe_hw *hw, u8 dropqueue)
+{
+ u32 fdirctrl;
+
+ DEBUGFUNC("ixgbe_set_fdir_drop_queue_82599");
+ /* Clear init done bit and drop queue field */
+ fdirctrl = IXGBE_READ_REG(hw, IXGBE_FDIRCTRL);
+ fdirctrl &= ~(IXGBE_FDIRCTRL_DROP_Q_MASK | IXGBE_FDIRCTRL_INIT_DONE);
+
+ /* Set drop queue */
+ fdirctrl |= (dropqueue << IXGBE_FDIRCTRL_DROP_Q_SHIFT);
+ if ((hw->mac.type == ixgbe_mac_X550) ||
+ (hw->mac.type == ixgbe_mac_X550EM_x) ||
+ (hw->mac.type == ixgbe_mac_X550EM_a))
+ fdirctrl |= IXGBE_FDIRCTRL_DROP_NO_MATCH;
+
+ IXGBE_WRITE_REG(hw, IXGBE_FDIRCMD,
+ (IXGBE_READ_REG(hw, IXGBE_FDIRCMD) |
+ IXGBE_FDIRCMD_CLEARHT));
+ IXGBE_WRITE_FLUSH(hw);
+ IXGBE_WRITE_REG(hw, IXGBE_FDIRCMD,
+ (IXGBE_READ_REG(hw, IXGBE_FDIRCMD) &
+ ~IXGBE_FDIRCMD_CLEARHT));
+ IXGBE_WRITE_FLUSH(hw);
+
+ /* write hashes and fdirctrl register, poll for completion */
+ ixgbe_fdir_enable_82599(hw, fdirctrl);
+}
+
/*
* These defines allow us to quickly generate all of the necessary instructions
* in the function below by simply calling out IXGBE_COMPUTE_SIG_HASH_ITERATION
* Note that the tunnel bit in input must not be set when the hardware
* tunneling support does not exist.
**/
-s32 ixgbe_fdir_add_signature_filter_82599(struct ixgbe_hw *hw,
- union ixgbe_atr_hash_dword input,
- union ixgbe_atr_hash_dword common,
- u8 queue)
+void ixgbe_fdir_add_signature_filter_82599(struct ixgbe_hw *hw,
+ union ixgbe_atr_hash_dword input,
+ union ixgbe_atr_hash_dword common,
+ u8 queue)
{
u64 fdirhashcmd;
u8 flow_type;
bool tunnel;
u32 fdircmd;
- s32 err;
DEBUGFUNC("ixgbe_fdir_add_signature_filter_82599");
break;
default:
DEBUGOUT(" Error on flow type input\n");
- return IXGBE_ERR_CONFIG;
+ return;
}
/* configure FDIRCMD register */
fdirhashcmd |= ixgbe_atr_compute_sig_hash_82599(input, common);
IXGBE_WRITE_REG64(hw, IXGBE_FDIRHASH, fdirhashcmd);
- err = ixgbe_fdir_check_cmd_complete(hw, &fdircmd);
- if (err) {
- DEBUGOUT("Flow Director command did not complete!\n");
- return err;
- }
-
DEBUGOUT2("Tx Queue=%x hash=%x\n", queue, (u32)fdirhashcmd);
- return IXGBE_SUCCESS;
+ return;
}
#define IXGBE_COMPUTE_BKT_HASH_ITERATION(_n) \
}
IXGBE_WRITE_REG_BE32(hw, IXGBE_FDIRIP6M, fdirip6m);
- /* Set all bits in FDIRSIP4M and FDIRDIP4M cloud mode */
+ /* Set all bits in FDIRTCPM, FDIRUDPM, FDIRSCTPM,
+ * FDIRSIP4M and FDIRDIP4M in cloud mode to allow
+ * L3/L3 packets to tunnel.
+ */
+ IXGBE_WRITE_REG(hw, IXGBE_FDIRTCPM, 0xFFFFFFFF);
+ IXGBE_WRITE_REG(hw, IXGBE_FDIRUDPM, 0xFFFFFFFF);
IXGBE_WRITE_REG_BE32(hw, IXGBE_FDIRDIP4M, 0xFFFFFFFF);
IXGBE_WRITE_REG_BE32(hw, IXGBE_FDIRSIP4M, 0xFFFFFFFF);
+ switch (hw->mac.type) {
+ case ixgbe_mac_X550:
+ case ixgbe_mac_X550EM_x:
+ case ixgbe_mac_X550EM_a:
+ IXGBE_WRITE_REG(hw, IXGBE_FDIRSCTPM, 0xFFFFFFFF);
+ break;
+ default:
+ break;
+ }
}
/* Now mask VM pool and destination IPv6 - bits 5 and 2 */
switch (hw->mac.type) {
case ixgbe_mac_X550:
case ixgbe_mac_X550EM_x:
+ case ixgbe_mac_X550EM_a:
IXGBE_WRITE_REG(hw, IXGBE_FDIRSCTPM, ~fdirtcpm);
break;
default:
return ret_val;
}
-
/**
* ixgbe_read_i2c_byte_82599 - Reads 8 bit word over I2C
* @hw: pointer to hardware structure
return status;
}
-
git.droids-corp.org / dpdk.git / blobdiff