DEBUGFUNC("ixgbe_device_supports_autoneg_fc");
switch (hw->phy.media_type) {
+ case ixgbe_media_type_fiber_fixed:
case ixgbe_media_type_fiber_qsfp:
case ixgbe_media_type_fiber:
/* flow control autoneg black list */
case IXGBE_DEV_ID_82599_T3_LOM:
case IXGBE_DEV_ID_X540T:
case IXGBE_DEV_ID_X540T1:
+ case IXGBE_DEV_ID_X540_BYPASS:
case IXGBE_DEV_ID_X550T:
case IXGBE_DEV_ID_X550T1:
case IXGBE_DEV_ID_X550EM_X_10G_T:
if (ret_val != IXGBE_SUCCESS)
goto out;
- /* only backplane uses autoc so fall though */
+ /* fall through - only backplane uses autoc */
+ case ixgbe_media_type_fiber_fixed:
case ixgbe_media_type_fiber_qsfp:
case ixgbe_media_type_fiber:
reg = IXGBE_READ_REG(hw, IXGBE_PCS1GANA);
/**
* ixgbe_shift_in_eeprom_bits - Shift data bits in from the EEPROM
* @hw: pointer to hardware structure
+ * @count: number of bits to shift
**/
STATIC u16 ixgbe_shift_in_eeprom_bits(struct ixgbe_hw *hw, u16 count)
{
/**
* ixgbe_lower_eeprom_clk - Lowers the EEPROM's clock input.
* @hw: pointer to hardware structure
- * @eecd: EECD's current value
+ * @eec: EEC's current value
**/
STATIC void ixgbe_lower_eeprom_clk(struct ixgbe_hw *hw, u32 *eec)
{
* ixgbe_add_uc_addr - Adds a secondary unicast address.
* @hw: pointer to hardware structure
* @addr: new address
+ * @vmdq: VMDq "set" or "pool" index
*
* Adds it to unused receive address register or goes into promiscuous mode.
**/
/**
* ixgbe_set_mta - Set bit-vector in multicast table
* @hw: pointer to hardware structure
- * @hash_value: Multicast address hash value
+ * @mc_addr: Multicast address
*
* Sets the bit-vector in the multicast table.
**/
switch (hw->phy.media_type) {
/* Autoneg flow control on fiber adapters */
+ case ixgbe_media_type_fiber_fixed:
case ixgbe_media_type_fiber_qsfp:
case ixgbe_media_type_fiber:
if (speed == IXGBE_LINK_SPEED_1GB_FULL)
/**
* prot_autoc_read_generic - Hides MAC differences needed for AUTOC read
* @hw: pointer to hardware structure
+ * @locked: bool to indicate whether the SW/FW lock was taken
* @reg_val: Value we read from AUTOC
*
* The default case requires no protection so just to the register read.
* ixgbe_find_vlvf_slot - find the vlanid or the first empty slot
* @hw: pointer to hardware structure
* @vlan: VLAN id to write to VLAN filter
+ * @vlvf_bypass: true to find vlanid only, false returns first empty slot if
+ * vlanid not found
+ *
*
* return the VLVF index where this VLAN id should be placed
*
u32 length, u32 timeout, bool return_data)
{
u32 hdr_size = sizeof(struct ixgbe_hic_hdr);
- u16 dword_len;
+ struct ixgbe_hic_hdr *resp = (struct ixgbe_hic_hdr *)buffer;
u16 buf_len;
s32 status;
u32 bi;
+ u32 dword_len;
DEBUGFUNC("ixgbe_host_interface_command");
IXGBE_LE32_TO_CPUS((uintptr_t)&buffer[bi]);
}
- /* If there is any thing in data position pull it in */
- buf_len = ((struct ixgbe_hic_hdr *)buffer)->buf_len;
+ /*
+ * If there is any thing in data position pull it in
+ * Read Flash command requires reading buffer length from
+ * two byes instead of one byte
+ */
+ if (resp->cmd == 0x30) {
+ for (; bi < dword_len + 2; bi++) {
+ buffer[bi] = IXGBE_READ_REG_ARRAY(hw, IXGBE_FLEX_MNG,
+ bi);
+ IXGBE_LE32_TO_CPUS(&buffer[bi]);
+ }
+ buf_len = (((u16)(resp->cmd_or_resp.ret_status) << 3)
+ & 0xF00) | resp->buf_len;
+ hdr_size += (2 << 2);
+ } else {
+ buf_len = resp->buf_len;
+ }
if (!buf_len)
goto rel_out;
* @min: driver version minor number
* @build: driver version build number
* @sub: driver version sub build number
+ * @len: unused
+ * @driver_ver: unused
*
* Sends driver version number to firmware through the manageability
* block. On success return IXGBE_SUCCESS
rxpktsize <<= IXGBE_RXPBSIZE_SHIFT;
for (; i < (num_pb / 2); i++)
IXGBE_WRITE_REG(hw, IXGBE_RXPBSIZE(i), rxpktsize);
- /* Fall through to configure remaining packet buffers */
+ /* fall through - configure remaining packet buffers */
case PBA_STRATEGY_EQUAL:
rxpktsize = (pbsize / (num_pb - i)) << IXGBE_RXPBSIZE_SHIFT;
for (; i < num_pb; i++)
/**
* ixgbe_get_thermal_sensor_data - Gathers thermal sensor data
* @hw: pointer to hardware structure
- * @data: pointer to the thermal sensor data structure
*
* Returns the thermal sensor data structure
**/
/* Set the module link speed */
switch (hw->phy.media_type) {
+ case ixgbe_media_type_fiber_fixed:
case ixgbe_media_type_fiber:
ixgbe_set_rate_select_speed(hw,
IXGBE_LINK_SPEED_10GB_FULL);
/* Set the module link speed */
switch (hw->phy.media_type) {
+ case ixgbe_media_type_fiber_fixed:
case ixgbe_media_type_fiber:
ixgbe_set_rate_select_speed(hw,
IXGBE_LINK_SPEED_1GB_FULL);