net/ixgbe: fix Tx prepare to set positive rte_errno

[dpdk.git] / drivers / net / ixgbe / base / ixgbe_common.c

diff --git a/drivers/net/ixgbe/base/ixgbe_common.c b/drivers/net/ixgbe/base/ixgbe_common.c
index d7b63c6..fb50719 100644 (file)
--- a/drivers/net/ixgbe/base/ixgbe_common.c
+++ b/drivers/net/ixgbe/base/ixgbe_common.c
@@ -138,7 +138,6 @@ bool ixgbe_device_supports_autoneg_fc(struct ixgbe_hw *hw)
        DEBUGFUNC("ixgbe_device_supports_autoneg_fc");
 
        switch (hw->phy.media_type) {
-       case ixgbe_media_type_fiber_fixed:
        case ixgbe_media_type_fiber_qsfp:
        case ixgbe_media_type_fiber:
                /* flow control autoneg black list */
@@ -172,7 +171,6 @@ bool ixgbe_device_supports_autoneg_fc(struct ixgbe_hw *hw)
                case IXGBE_DEV_ID_82599_T3_LOM:
                case IXGBE_DEV_ID_X540T:
                case IXGBE_DEV_ID_X540T1:
-               case IXGBE_DEV_ID_X540_BYPASS:
                case IXGBE_DEV_ID_X550T:
                case IXGBE_DEV_ID_X550T1:
                case IXGBE_DEV_ID_X550EM_X_10G_T:
@@ -238,7 +236,6 @@ s32 ixgbe_setup_fc_generic(struct ixgbe_hw *hw)
                        goto out;
 
                /* fall through - only backplane uses autoc */
-       case ixgbe_media_type_fiber_fixed:
        case ixgbe_media_type_fiber_qsfp:
        case ixgbe_media_type_fiber:
                reg = IXGBE_READ_REG(hw, IXGBE_PCS1GANA);
@@ -3098,7 +3095,6 @@ void ixgbe_fc_autoneg(struct ixgbe_hw *hw)
 
        switch (hw->phy.media_type) {
        /* Autoneg flow control on fiber adapters */
-       case ixgbe_media_type_fiber_fixed:
        case ixgbe_media_type_fiber_qsfp:
        case ixgbe_media_type_fiber:
                if (speed == IXGBE_LINK_SPEED_1GB_FULL)
@@ -5238,7 +5234,6 @@ s32 ixgbe_setup_mac_link_multispeed_fiber(struct ixgbe_hw *hw,
 
                /* Set the module link speed */
                switch (hw->phy.media_type) {
-               case ixgbe_media_type_fiber_fixed:
                case ixgbe_media_type_fiber:
                        ixgbe_set_rate_select_speed(hw,
                                                    IXGBE_LINK_SPEED_10GB_FULL);
@@ -5264,10 +5259,10 @@ s32 ixgbe_setup_mac_link_multispeed_fiber(struct ixgbe_hw *hw,
                ixgbe_flap_tx_laser(hw);
 
                /* Wait for the controller to acquire link.  Per IEEE 802.3ap,
-                * Section 73.10.2, we may have to wait up to 500ms if KR is
+                * Section 73.10.2, we may have to wait up to 1000ms if KR is
                 * attempted.  82599 uses the same timing for 10g SFI.
                 */
-               for (i = 0; i < 5; i++) {
+               for (i = 0; i < 10; i++) {
                        /* Wait for the link partner to also set speed */
                        msec_delay(100);
 
@@ -5289,7 +5284,6 @@ s32 ixgbe_setup_mac_link_multispeed_fiber(struct ixgbe_hw *hw,
 
                /* Set the module link speed */
                switch (hw->phy.media_type) {
-               case ixgbe_media_type_fiber_fixed:
                case ixgbe_media_type_fiber:
                        ixgbe_set_rate_select_speed(hw,
                                                    IXGBE_LINK_SPEED_1GB_FULL);