hw->phy.type = ixgbe_phy_x550em_kr;
break;
case IXGBE_DEV_ID_X550EM_A_10G_T:
- case IXGBE_DEV_ID_X550EM_A_1G_T:
- case IXGBE_DEV_ID_X550EM_A_1G_T_L:
case IXGBE_DEV_ID_X550EM_X_1G_T:
case IXGBE_DEV_ID_X550EM_X_10G_T:
return ixgbe_identify_phy_generic(hw);
+ case IXGBE_DEV_ID_X550EM_A_1G_T:
+ case IXGBE_DEV_ID_X550EM_A_1G_T_L:
+ hw->phy.type = ixgbe_phy_fw;
+ hw->phy.ops.read_reg = NULL;
+ hw->phy.ops.write_reg = NULL;
+ if (hw->bus.lan_id)
+ hw->phy.phy_semaphore_mask |= IXGBE_GSSR_PHY1_SM;
+ else
+ hw->phy.phy_semaphore_mask |= IXGBE_GSSR_PHY0_SM;
+ break;
default:
break;
}
else
hw->phy.phy_semaphore_mask = IXGBE_GSSR_PHY0_SM;
- hw->phy.type = ixgbe_phy_m88;
+ hw->phy.type = ixgbe_phy_fw;
hw->phy.ops.read_reg = NULL;
hw->phy.ops.write_reg = NULL;
return ixgbe_get_phy_id_fw(hw);
break;
}
- if ((hw->device_id == IXGBE_DEV_ID_X550EM_A_1G_T) ||
- (hw->device_id == IXGBE_DEV_ID_X550EM_A_1G_T_L)) {
+ switch (hw->device_id) {
+ case IXGBE_DEV_ID_X550EM_A_1G_T:
+ case IXGBE_DEV_ID_X550EM_A_1G_T_L:
mac->ops.fc_autoneg = ixgbe_fc_autoneg_sgmii_x550em_a;
mac->ops.setup_fc = ixgbe_fc_autoneg_fw;
- }
-
- switch (hw->device_id) {
- case IXGBE_DEV_ID_X550EM_A_KR:
- case IXGBE_DEV_ID_X550EM_A_KR_L:
mac->ops.setup_eee = ixgbe_setup_eee_fw;
+ hw->phy.eee_speeds_supported = IXGBE_LINK_SPEED_100_FULL |
+ IXGBE_LINK_SPEED_1GB_FULL;
+ hw->phy.eee_speeds_advertised = hw->phy.eee_speeds_supported;
break;
default:
- mac->ops.setup_eee = NULL;
+ break;
}
return ret_val;
ixgbe_write_i2c_combined_generic_unlocked;
link->addr = IXGBE_CS4227;
+
return ret_val;
}
return IXGBE_SUCCESS;
}
-/**
- * ixgbe_enable_eee_x550 - Enable EEE support
- * @hw: pointer to hardware structure
- */
-STATIC s32 ixgbe_enable_eee_x550(struct ixgbe_hw *hw)
-{
- u32 link_reg;
- s32 status;
-
- switch (hw->device_id) {
- case IXGBE_DEV_ID_X550EM_A_KR:
- case IXGBE_DEV_ID_X550EM_A_KR_L:
- status = hw->mac.ops.read_iosf_sb_reg(hw,
- IXGBE_KRM_LINK_CTRL_1(hw->bus.lan_id),
- IXGBE_SB_IOSF_TARGET_KR_PHY, &link_reg);
- if (status != IXGBE_SUCCESS)
- return status;
-
- link_reg |= IXGBE_KRM_LINK_CTRL_1_TETH_EEE_CAP_KR |
- IXGBE_KRM_LINK_CTRL_1_TETH_EEE_CAP_KX;
-
- /* Don't advertise FEC capability when EEE enabled. */
- link_reg &= ~IXGBE_KRM_LINK_CTRL_1_TETH_AN_CAP_FEC;
-
- status = hw->mac.ops.write_iosf_sb_reg(hw,
- IXGBE_KRM_LINK_CTRL_1(hw->bus.lan_id),
- IXGBE_SB_IOSF_TARGET_KR_PHY, link_reg);
- if (status != IXGBE_SUCCESS)
- return status;
- break;
- default:
- break;
- }
-
- return IXGBE_SUCCESS;
-}
-
-/**
- * ixgbe_disable_eee_x550 - Disable EEE support
- * @hw: pointer to hardware structure
- */
-STATIC s32 ixgbe_disable_eee_x550(struct ixgbe_hw *hw)
-{
- u32 link_reg;
- s32 status;
-
- switch (hw->device_id) {
- case IXGBE_DEV_ID_X550EM_X_KR:
- case IXGBE_DEV_ID_X550EM_A_KR:
- case IXGBE_DEV_ID_X550EM_A_KR_L:
- status = hw->mac.ops.read_iosf_sb_reg(hw,
- IXGBE_KRM_LINK_CTRL_1(hw->bus.lan_id),
- IXGBE_SB_IOSF_TARGET_KR_PHY, &link_reg);
- if (status != IXGBE_SUCCESS)
- return status;
-
- link_reg &= ~(IXGBE_KRM_LINK_CTRL_1_TETH_EEE_CAP_KR |
- IXGBE_KRM_LINK_CTRL_1_TETH_EEE_CAP_KX);
-
- /* Advertise FEC capability when EEE is disabled. */
- link_reg |= IXGBE_KRM_LINK_CTRL_1_TETH_AN_CAP_FEC;
-
- status = hw->mac.ops.write_iosf_sb_reg(hw,
- IXGBE_KRM_LINK_CTRL_1(hw->bus.lan_id),
- IXGBE_SB_IOSF_TARGET_KR_PHY, link_reg);
- if (status != IXGBE_SUCCESS)
- return status;
- break;
- default:
- break;
- }
-
- return IXGBE_SUCCESS;
-}
-
-/**
- * ixgbe_setup_eee_X550 - Enable/disable EEE support
- * @hw: pointer to the HW structure
- * @enable_eee: boolean flag to enable EEE
- *
- * Enable/disable EEE based on enable_eee flag.
- * Auto-negotiation must be started after BASE-T EEE bits in PHY register 7.3C
- * are modified.
- *
- **/
-s32 ixgbe_setup_eee_X550(struct ixgbe_hw *hw, bool enable_eee)
-{
- s32 status;
- u32 eeer;
-
- DEBUGFUNC("ixgbe_setup_eee_X550");
-
- eeer = IXGBE_READ_REG(hw, IXGBE_EEER);
- /* Enable or disable EEE per flag */
- if (enable_eee) {
- eeer |= (IXGBE_EEER_TX_LPI_EN | IXGBE_EEER_RX_LPI_EN);
-
- status = ixgbe_enable_eee_x550(hw);
- if (status)
- return status;
- } else {
- eeer &= ~(IXGBE_EEER_TX_LPI_EN | IXGBE_EEER_RX_LPI_EN);
-
- status = ixgbe_disable_eee_x550(hw);
- if (status)
- return status;
- }
- IXGBE_WRITE_REG(hw, IXGBE_EEER, eeer);
-
- return IXGBE_SUCCESS;
-}
-
/**
* ixgbe_set_source_address_pruning_X550 - Enable/Disbale source address pruning
* @hw: pointer to hardware structure
}
/**
- * ixgbe_setup_sgmii_m88 - Set up link for sgmii with Marvell PHYs
+ * ixgbe_setup_sgmii_fw - Set up link for sgmii with firmware-controlled PHYs
* @hw: pointer to hardware structure
*/
-STATIC s32 ixgbe_setup_sgmii_m88(struct ixgbe_hw *hw, ixgbe_link_speed speed,
- bool autoneg_wait)
+STATIC s32 ixgbe_setup_sgmii_fw(struct ixgbe_hw *hw, ixgbe_link_speed speed,
+ bool autoneg_wait)
{
struct ixgbe_mac_info *mac = &hw->mac;
u32 lval, sval, flx_val;
if (hw->mac.type == ixgbe_mac_X550EM_a) {
if (hw->device_id == IXGBE_DEV_ID_X550EM_A_1G_T ||
hw->device_id == IXGBE_DEV_ID_X550EM_A_1G_T_L) {
- mac->ops.setup_link = ixgbe_setup_sgmii_m88;
+ mac->ops.setup_link = ixgbe_setup_sgmii_fw;
+ mac->ops.check_link =
+ ixgbe_check_mac_link_generic;
} else {
mac->ops.setup_link =
ixgbe_setup_mac_link_t_X550em;
DEBUGFUNC("ixgbe_get_link_capabilities_X550em");
+ if (hw->phy.type == ixgbe_phy_fw) {
+ *autoneg = true;
+ *speed = hw->phy.speeds_supported;
+ return 0;
+ }
+
/* SFP */
if (hw->phy.media_type == ixgbe_media_type_fiber) {
*speed = IXGBE_LINK_SPEED_10GB_FULL;
} else {
switch (hw->phy.type) {
- case ixgbe_phy_m88:
- *speed = IXGBE_LINK_SPEED_1GB_FULL |
- IXGBE_LINK_SPEED_100_FULL |
- IXGBE_LINK_SPEED_10_FULL;
- break;
case ixgbe_phy_sgmii:
*speed = IXGBE_LINK_SPEED_1GB_FULL;
break;
}
/**
- * ixgbe_setup_m88 - setup m88 PHY
+ * ixgbe_reset_phy_fw - Reset firmware-controlled PHYs
* @hw: pointer to hardware structure
*/
-STATIC s32 ixgbe_setup_m88(struct ixgbe_hw *hw)
+static s32 ixgbe_reset_phy_fw(struct ixgbe_hw *hw)
{
- u32 mask = hw->phy.phy_semaphore_mask | IXGBE_GSSR_TOKEN_SM;
- u16 reg;
+ u32 store[FW_PHY_ACT_DATA_COUNT] = { 0 };
s32 rc;
if (hw->phy.reset_disable || ixgbe_check_reset_blocked(hw))
return IXGBE_SUCCESS;
- rc = hw->mac.ops.acquire_swfw_sync(hw, mask);
+ rc = ixgbe_fw_phy_activity(hw, FW_PHY_ACT_PHY_SW_RESET, &store);
if (rc)
return rc;
+ memset(store, 0, sizeof(store));
- rc = hw->phy.ops.read_reg_mdi(hw, IXGBE_M88E1500_COPPER_CTRL, 0, ®);
- if (rc)
- goto out;
- if (reg & IXGBE_M88E1500_COPPER_CTRL_POWER_DOWN) {
- reg &= ~IXGBE_M88E1500_COPPER_CTRL_POWER_DOWN;
- hw->phy.ops.write_reg_mdi(hw, IXGBE_M88E1500_COPPER_CTRL, 0,
- reg);
- }
-
- rc = hw->phy.ops.read_reg_mdi(hw, IXGBE_M88E1500_MAC_CTRL_1, 0, ®);
- if (rc)
- goto out;
- if (reg & IXGBE_M88E1500_MAC_CTRL_1_POWER_DOWN) {
- reg &= ~IXGBE_M88E1500_MAC_CTRL_1_POWER_DOWN;
- hw->phy.ops.write_reg_mdi(hw, IXGBE_M88E1500_MAC_CTRL_1, 0,
- reg);
- }
-
- rc = hw->phy.ops.write_reg_mdi(hw, IXGBE_M88E1500_PAGE_ADDR, 0, 2);
- if (rc)
- goto out;
-
- rc = hw->phy.ops.read_reg_mdi(hw, IXGBE_M88E1500_MAC_SPEC_CTRL, 0,
- ®);
- if (rc)
- goto out;
- if (reg & IXGBE_M88E1500_MAC_SPEC_CTRL_POWER_DOWN) {
- reg &= ~IXGBE_M88E1500_MAC_SPEC_CTRL_POWER_DOWN;
- hw->phy.ops.write_reg_mdi(hw, IXGBE_M88E1500_MAC_SPEC_CTRL, 0,
- reg);
- rc = hw->phy.ops.write_reg_mdi(hw, IXGBE_M88E1500_PAGE_ADDR, 0,
- 0);
- if (rc)
- goto out;
- rc = hw->phy.ops.read_reg_mdi(hw, IXGBE_M88E1500_COPPER_CTRL, 0,
- ®);
- if (rc)
- goto out;
- reg |= IXGBE_M88E1500_COPPER_CTRL_RESET;
- hw->phy.ops.write_reg_mdi(hw, IXGBE_M88E1500_COPPER_CTRL, 0,
- reg);
- usec_delay(50);
- } else {
- rc = hw->phy.ops.write_reg_mdi(hw, IXGBE_M88E1500_PAGE_ADDR, 0,
- 0);
- if (rc)
- goto out;
- }
-
- rc = hw->phy.ops.read_reg_mdi(hw, IXGBE_M88E1500_COPPER_CTRL, 0, ®);
- if (rc)
- goto out;
-
- if (!(reg & IXGBE_M88E1500_COPPER_CTRL_AN_EN)) {
- reg |= IXGBE_M88E1500_COPPER_CTRL_AN_EN;
- hw->phy.ops.write_reg_mdi(hw, IXGBE_M88E1500_COPPER_CTRL, 0,
- reg);
- }
-
- rc = hw->phy.ops.read_reg_mdi(hw, IXGBE_M88E1500_1000T_CTRL, 0, ®);
- if (rc)
- goto out;
- reg &= ~IXGBE_M88E1500_1000T_CTRL_HALF_DUPLEX;
- reg &= ~IXGBE_M88E1500_1000T_CTRL_FULL_DUPLEX;
- if (hw->phy.autoneg_advertised & IXGBE_LINK_SPEED_1GB_FULL)
- reg |= IXGBE_M88E1500_1000T_CTRL_FULL_DUPLEX;
- hw->phy.ops.write_reg_mdi(hw, IXGBE_M88E1500_1000T_CTRL, 0, reg);
-
- rc = hw->phy.ops.read_reg_mdi(hw, IXGBE_M88E1500_COPPER_AN, 0, ®);
- if (rc)
- goto out;
- reg &= ~IXGBE_M88E1500_COPPER_AN_T4;
- reg &= ~IXGBE_M88E1500_COPPER_AN_100TX_FD;
- reg &= ~IXGBE_M88E1500_COPPER_AN_100TX_HD;
- reg &= ~IXGBE_M88E1500_COPPER_AN_10TX_FD;
- reg &= ~IXGBE_M88E1500_COPPER_AN_10TX_HD;
-
- /* Flow control auto negotiation configuration was moved from here to
- * the function ixgbe_setup_fc_sgmii_x550em_a()
- */
-
- if (hw->phy.autoneg_advertised & IXGBE_LINK_SPEED_100_FULL)
- reg |= IXGBE_M88E1500_COPPER_AN_100TX_FD;
- if (hw->phy.autoneg_advertised & IXGBE_LINK_SPEED_10_FULL)
- reg |= IXGBE_M88E1500_COPPER_AN_10TX_FD;
- hw->phy.ops.write_reg_mdi(hw, IXGBE_M88E1500_COPPER_AN, 0, reg);
-
- rc = hw->phy.ops.read_reg_mdi(hw, IXGBE_M88E1500_COPPER_CTRL, 0, ®);
- if (rc)
- goto out;
- reg |= IXGBE_M88E1500_COPPER_CTRL_RESTART_AN;
- hw->phy.ops.write_reg_mdi(hw, IXGBE_M88E1500_COPPER_CTRL, 0, reg);
-
-
- hw->mac.ops.release_swfw_sync(hw, mask);
- return rc;
-
-out:
- hw->phy.ops.write_reg_mdi(hw, IXGBE_M88E1500_PAGE_ADDR, 0, 0);
- hw->mac.ops.release_swfw_sync(hw, mask);
- return rc;
-}
-
-/**
- * ixgbe_reset_phy_m88e1500 - Reset m88e1500 PHY
- * @hw: pointer to hardware structure
- *
- * The PHY token must be held when calling this function.
- */
-static s32 ixgbe_reset_phy_m88e1500(struct ixgbe_hw *hw)
-{
- u16 reg;
- s32 rc;
-
- rc = hw->phy.ops.write_reg_mdi(hw, IXGBE_M88E1500_PAGE_ADDR, 0, 0);
+ rc = ixgbe_fw_phy_activity(hw, FW_PHY_ACT_INIT_PHY, &store);
if (rc)
return rc;
- rc = hw->phy.ops.read_reg_mdi(hw, IXGBE_M88E1500_COPPER_CTRL, 0, ®);
- if (rc)
- return rc;
-
- reg |= IXGBE_M88E1500_COPPER_CTRL_RESET;
- rc = hw->phy.ops.write_reg_mdi(hw, IXGBE_M88E1500_COPPER_CTRL, 0, reg);
-
- usec_delay(10);
-
- return rc;
-}
-
-/**
- * ixgbe_reset_phy_m88e1543 - Reset m88e1543 PHY
- * @hw: pointer to hardware structure
- *
- * The PHY token must be held when calling this function.
- */
-static s32 ixgbe_reset_phy_m88e1543(struct ixgbe_hw *hw)
-{
- return hw->phy.ops.write_reg_mdi(hw, IXGBE_M88E1500_PAGE_ADDR, 0, 0);
+ return ixgbe_setup_fw_link(hw);
}
/**
- * ixgbe_reset_phy_m88 - Reset m88 PHY
+ * ixgbe_check_overtemp_fw - Check firmware-controlled PHYs for overtemp
* @hw: pointer to hardware structure
*/
-STATIC s32 ixgbe_reset_phy_m88(struct ixgbe_hw *hw)
+static s32 ixgbe_check_overtemp_fw(struct ixgbe_hw *hw)
{
- u32 mask = hw->phy.phy_semaphore_mask | IXGBE_GSSR_TOKEN_SM;
- u16 reg;
+ u32 store[FW_PHY_ACT_DATA_COUNT] = { 0 };
s32 rc;
- if (hw->phy.reset_disable || ixgbe_check_reset_blocked(hw))
- return IXGBE_SUCCESS;
-
- rc = hw->mac.ops.acquire_swfw_sync(hw, mask);
+ rc = ixgbe_fw_phy_activity(hw, FW_PHY_ACT_GET_LINK_INFO, &store);
if (rc)
return rc;
- switch (hw->phy.id) {
- case IXGBE_M88E1500_E_PHY_ID:
- rc = ixgbe_reset_phy_m88e1500(hw);
- break;
- case IXGBE_M88E1543_E_PHY_ID:
- rc = ixgbe_reset_phy_m88e1543(hw);
- break;
- default:
- rc = IXGBE_ERR_PHY;
- break;
+ if (store[0] & FW_PHY_ACT_GET_LINK_INFO_TEMP) {
+ ixgbe_shutdown_fw_phy(hw);
+ return IXGBE_ERR_OVERTEMP;
}
-
- rc = hw->phy.ops.write_reg_mdi(hw, IXGBE_M88E1500_PAGE_ADDR, 0, 1);
- if (rc)
- goto out;
-
- reg = IXGBE_M88E1500_FIBER_CTRL_RESET |
- IXGBE_M88E1500_FIBER_CTRL_DUPLEX_FULL |
- IXGBE_M88E1500_FIBER_CTRL_SPEED_MSB;
- rc = hw->phy.ops.write_reg_mdi(hw, IXGBE_M88E1500_FIBER_CTRL, 0, reg);
- if (rc)
- goto out;
-
- rc = hw->phy.ops.write_reg_mdi(hw, IXGBE_M88E1500_PAGE_ADDR, 0, 18);
- if (rc)
- goto out;
-
- reg = IXGBE_M88E1500_GEN_CTRL_RESET |
- IXGBE_M88E1500_GEN_CTRL_MODE_SGMII_COPPER;
- rc = hw->phy.ops.write_reg_mdi(hw, IXGBE_M88E1500_GEN_CTRL, 0, reg);
- if (rc)
- goto out;
-
- rc = hw->phy.ops.write_reg_mdi(hw, IXGBE_M88E1500_PAGE_ADDR, 0, 1);
- if (rc)
- goto out;
-
- reg = IXGBE_M88E1500_FIBER_CTRL_RESET |
- IXGBE_M88E1500_FIBER_CTRL_AN_EN |
- IXGBE_M88E1500_FIBER_CTRL_DUPLEX_FULL |
- IXGBE_M88E1500_FIBER_CTRL_SPEED_MSB;
- rc = hw->phy.ops.write_reg_mdi(hw, IXGBE_M88E1500_FIBER_CTRL, 0, reg);
- if (rc)
- goto out;
-
- rc = hw->phy.ops.write_reg_mdi(hw, IXGBE_M88E1500_PAGE_ADDR, 0, 0);
- if (rc)
- goto out;
-
- reg = (IXGBE_M88E1500_MAC_CTRL_1_DWN_4X <<
- IXGBE_M88E1500_MAC_CTRL_1_DWN_SHIFT) |
- (IXGBE_M88E1500_MAC_CTRL_1_ED_TM <<
- IXGBE_M88E1500_MAC_CTRL_1_ED_SHIFT) |
- (IXGBE_M88E1500_MAC_CTRL_1_MDIX_AUTO <<
- IXGBE_M88E1500_MAC_CTRL_1_MDIX_SHIFT);
- rc = hw->phy.ops.write_reg_mdi(hw, IXGBE_M88E1500_MAC_CTRL_1, 0, reg);
- if (rc)
- goto out;
-
- reg = IXGBE_M88E1500_COPPER_CTRL_RESET |
- IXGBE_M88E1500_COPPER_CTRL_AN_EN |
- IXGBE_M88E1500_COPPER_CTRL_RESTART_AN |
- IXGBE_M88E1500_COPPER_CTRL_FULL_DUPLEX |
- IXGBE_M88E1500_COPPER_CTRL_SPEED_MSB;
- rc = hw->phy.ops.write_reg_mdi(hw, IXGBE_M88E1500_COPPER_CTRL, 0, reg);
- if (rc)
- goto out;
-
- hw->mac.ops.release_swfw_sync(hw, mask);
-
- /* In case of first reset set advertised speeds to default value */
- if (!hw->phy.autoneg_advertised)
- hw->phy.autoneg_advertised = IXGBE_LINK_SPEED_1GB_FULL |
- IXGBE_LINK_SPEED_100_FULL |
- IXGBE_LINK_SPEED_10_FULL;
-
- return ixgbe_setup_m88(hw);
-
-out:
- hw->phy.ops.write_reg_mdi(hw, IXGBE_M88E1500_PAGE_ADDR, 0, 0);
- hw->mac.ops.release_swfw_sync(hw, mask);
- return rc;
+ return IXGBE_SUCCESS;
}
/**
DEBUGFUNC("ixgbe_init_phy_ops_X550em");
+ hw->mac.ops.set_lan_id(hw);
+ ixgbe_read_mng_if_sel_x550em(hw);
+
if (hw->mac.ops.get_media_type(hw) == ixgbe_media_type_fiber) {
phy->phy_semaphore_mask = IXGBE_GSSR_SHARED_I2C_SM;
ixgbe_setup_mux_ctl(hw);
phy->ops.write_reg_mdi = ixgbe_write_phy_reg_mdi_22;
hw->phy.ops.read_reg = ixgbe_read_phy_reg_x550a;
hw->phy.ops.write_reg = ixgbe_write_phy_reg_x550a;
+ phy->ops.check_overtemp = ixgbe_check_overtemp_fw;
if (hw->bus.lan_id)
hw->phy.phy_semaphore_mask |= IXGBE_GSSR_PHY1_SM;
else
/* Identify the PHY or SFP module */
ret_val = phy->ops.identify(hw);
- if (ret_val == IXGBE_ERR_SFP_NOT_SUPPORTED)
+ if (ret_val == IXGBE_ERR_SFP_NOT_SUPPORTED ||
+ ret_val == IXGBE_ERR_PHY_ADDR_INVALID)
return ret_val;
/* Setup function pointers based on detected hardware */
case ixgbe_phy_sgmii:
phy->ops.setup_link = NULL;
break;
- case ixgbe_phy_m88:
- phy->ops.setup_link = ixgbe_setup_m88;
- phy->ops.reset = ixgbe_reset_phy_m88;
+ case ixgbe_phy_fw:
+ phy->ops.setup_link = ixgbe_setup_fw_link;
+ phy->ops.reset = ixgbe_reset_phy_fw;
break;
default:
break;
return status;
/* Reset PHY */
- if (!hw->phy.reset_disable && hw->phy.ops.reset)
- hw->phy.ops.reset(hw);
+ if (!hw->phy.reset_disable && hw->phy.ops.reset) {
+ if (hw->phy.ops.reset(hw) == IXGBE_ERR_OVERTEMP)
+ return IXGBE_ERR_OVERTEMP;
+ }
mac_reset_top:
/* Issue global reset to the MAC. Needs to be SW reset if link is up.
if (ext_ability & IXGBE_MDIO_PHY_1000BASET_ABILITY)
physical_layer |= IXGBE_PHYSICAL_LAYER_1000BASE_T;
break;
- case ixgbe_phy_m88:
- physical_layer = IXGBE_PHYSICAL_LAYER_1000BASE_T;
+ case ixgbe_phy_fw:
+ if (hw->phy.speeds_supported & IXGBE_LINK_SPEED_1GB_FULL)
+ physical_layer |= IXGBE_PHYSICAL_LAYER_1000BASE_T;
+ if (hw->phy.speeds_supported & IXGBE_LINK_SPEED_100_FULL)
+ physical_layer |= IXGBE_PHYSICAL_LAYER_100BASE_TX;
+ if (hw->phy.speeds_supported & IXGBE_LINK_SPEED_10_FULL)
+ physical_layer |= IXGBE_PHYSICAL_LAYER_10BASE_T;
+ break;
default:
break;
}
void ixgbe_fc_autoneg_sgmii_x550em_a(struct ixgbe_hw *hw)
{
s32 status = IXGBE_ERR_FC_NOT_NEGOTIATED;
- u16 reg, pcs_an_lp, pcs_an;
+ u32 info[FW_PHY_ACT_DATA_COUNT] = { 0 };
ixgbe_link_speed speed;
bool link_up;
}
/* Check if auto-negotiation has completed */
- status = hw->phy.ops.read_reg(hw, IXGBE_M88E1500_COPPER_STATUS,
- IXGBE_MDIO_ZERO_DEV_TYPE, ®);
+ status = ixgbe_fw_phy_activity(hw, FW_PHY_ACT_GET_LINK_INFO, &info);
if (status != IXGBE_SUCCESS ||
- (reg & IXGBE_M88E1500_COPPER_STATUS_AN_DONE) == 0) {
+ !(info[0] & FW_PHY_ACT_GET_LINK_INFO_AN_COMPLETE)) {
DEBUGOUT("Auto-Negotiation did not complete\n");
status = IXGBE_ERR_FC_NOT_NEGOTIATED;
goto out;
}
- /* Get the advertized flow control */
- status = hw->phy.ops.read_reg(hw, IXGBE_M88E1500_COPPER_AN,
- IXGBE_MDIO_ZERO_DEV_TYPE, &pcs_an);
- if (status != IXGBE_SUCCESS)
- goto out;
-
- /* Get link partner's flow control */
- status = hw->phy.ops.read_reg(hw,
- IXGBE_M88E1500_COPPER_AN_LP_ABILITY,
- IXGBE_MDIO_ZERO_DEV_TYPE, &pcs_an_lp);
- if (status != IXGBE_SUCCESS)
- goto out;
-
/* Negotiate the flow control */
- status = ixgbe_negotiate_fc(hw, (u32)pcs_an, (u32)pcs_an_lp,
- IXGBE_M88E1500_COPPER_AN_PAUSE,
- IXGBE_M88E1500_COPPER_AN_AS_PAUSE,
- IXGBE_M88E1500_COPPER_AN_LP_PAUSE,
- IXGBE_M88E1500_COPPER_AN_LP_AS_PAUSE);
+ status = ixgbe_negotiate_fc(hw, info[0], info[0],
+ FW_PHY_ACT_GET_LINK_INFO_FC_RX,
+ FW_PHY_ACT_GET_LINK_INFO_FC_TX,
+ FW_PHY_ACT_GET_LINK_INFO_LP_FC_RX,
+ FW_PHY_ACT_GET_LINK_INFO_LP_FC_TX);
out:
if (status == IXGBE_SUCCESS) {
}
}
-/**
- * ixgbe_setup_fc_sgmii_x550em_a - Set up flow control
- * @hw: pointer to hardware structure
- *
- * Called at init time to set up flow control.
- **/
-s32 ixgbe_setup_fc_sgmii_x550em_a(struct ixgbe_hw *hw)
-{
- u16 reg;
- s32 rc;
-
- /* Validate the requested mode */
- if (hw->fc.strict_ieee && hw->fc.requested_mode == ixgbe_fc_rx_pause) {
- ERROR_REPORT1(IXGBE_ERROR_UNSUPPORTED,
- "ixgbe_fc_rx_pause not valid in strict IEEE mode\n");
- return IXGBE_ERR_INVALID_LINK_SETTINGS;
- }
-
- if (hw->fc.requested_mode == ixgbe_fc_default)
- hw->fc.requested_mode = ixgbe_fc_full;
-
- /* Read contents of the Auto-Negotiation register, page 0 reg 4 */
- rc = hw->phy.ops.read_reg(hw, IXGBE_M88E1500_COPPER_AN,
- IXGBE_MDIO_ZERO_DEV_TYPE, ®);
- if (rc)
- goto out;
-
- /* Disable all the settings related to Flow control Auto-negotiation */
- reg &= ~IXGBE_M88E1500_COPPER_AN_AS_PAUSE;
- reg &= ~IXGBE_M88E1500_COPPER_AN_PAUSE;
-
- /* Configure the Asymmetric and symmetric pause according to the user
- * requested mode.
- */
- switch (hw->fc.requested_mode) {
- case ixgbe_fc_full:
- reg |= IXGBE_M88E1500_COPPER_AN_PAUSE;
- reg |= IXGBE_M88E1500_COPPER_AN_AS_PAUSE;
- break;
- case ixgbe_fc_rx_pause:
- reg |= IXGBE_M88E1500_COPPER_AN_PAUSE;
- reg |= IXGBE_M88E1500_COPPER_AN_AS_PAUSE;
- break;
- case ixgbe_fc_tx_pause:
- reg |= IXGBE_M88E1500_COPPER_AN_AS_PAUSE;
- break;
- default:
- break;
- }
-
- /* Write back to the Auto-Negotiation register with newly configured
- * fields
- */
- hw->phy.ops.write_reg(hw, IXGBE_M88E1500_COPPER_AN,
- IXGBE_MDIO_ZERO_DEV_TYPE, reg);
-
- /* In this section of the code we restart Auto-negotiation */
-
- /* Read the CONTROL register, Page 0 reg 0 */
- rc = hw->phy.ops.read_reg(hw, IXGBE_M88E1500_COPPER_CTRL,
- IXGBE_MDIO_ZERO_DEV_TYPE, ®);
- if (rc)
- goto out;
-
- /* Set the bit to restart Auto-Neg. The bit to enable Auto-neg is ON
- * by default
- */
- reg |= IXGBE_M88E1500_COPPER_CTRL_RESTART_AN;
-
- /* write the new values to the register to restart Auto-Negotiation */
- hw->phy.ops.write_reg(hw, IXGBE_M88E1500_COPPER_CTRL,
- IXGBE_MDIO_ZERO_DEV_TYPE, reg);
-
-out:
- return rc;
-}
-
/**
* ixgbe_setup_fc_backplane_x550em_a - Set up flow control
* @hw: pointer to hardware structure
git.droids-corp.org / dpdk.git / blobdiff