ixgbe/base: rework X550em PHY setup function

[dpdk.git] / drivers / net / ixgbe / base / ixgbe_x550.c

diff --git a/drivers/net/ixgbe/base/ixgbe_x550.c b/drivers/net/ixgbe/base/ixgbe_x550.c
index 2c8abce..bc0ca53 100644 (file)
--- a/drivers/net/ixgbe/base/ixgbe_x550.c
+++ b/drivers/net/ixgbe/base/ixgbe_x550.c
@@ -1150,7 +1150,8 @@ s32 ixgbe_init_phy_ops_X550em(struct ixgbe_hw *hw)
                phy->ops.write_reg = ixgbe_write_phy_reg_x550em;
                break;
        case ixgbe_phy_x550em_ext_t:
-               phy->ops.setup_internal_link = ixgbe_setup_internal_phy_x550em;
+               phy->ops.setup_internal_link =
+                                        ixgbe_setup_internal_phy_t_x550em;
                phy->ops.enter_lplu = ixgbe_enter_lplu_t_x550em;
                break;
        default:
@@ -1537,35 +1538,27 @@ s32 ixgbe_setup_mac_link_sfp_x550em(struct ixgbe_hw *hw,
 }
 
 /**
- * ixgbe_setup_internal_phy_x550em - Configure integrated KR PHY
+ * ixgbe_setup_internal_phy_t_x550em - Configure KR PHY to X557 link
  * @hw: point to hardware structure
  *
- * Configures the integrated KR PHY to talk to the external PHY. The base
- * driver will call this function when it gets notification via interrupt from
- * the external PHY. This function forces the internal PHY into iXFI mode at
- * the correct speed.
+ * Configures the link between the integrated KR PHY and the external X557 PHY
+ * The driver will call this function when it gets a link status change
+ * interrupt from the X557 PHY. This function configures the link speed
+ * between the PHYs to match the link speed of the BASE-T link.
  *
  * A return of a non-zero value indicates an error, and the base driver should
  * not report link up.
  */
-s32 ixgbe_setup_internal_phy_x550em(struct ixgbe_hw *hw)
+s32 ixgbe_setup_internal_phy_t_x550em(struct ixgbe_hw *hw)
 {
        u32 status;
-       u16 lasi, autoneg_status, speed;
+       u16 autoneg_status, speed;
        ixgbe_link_speed force_speed;
 
-       /* Verify that the external link status has changed */
-       status = hw->phy.ops.read_reg(hw, IXGBE_MDIO_XENPAK_LASI_STATUS,
-                                     IXGBE_MDIO_PMA_PMD_DEV_TYPE,
-                                     &lasi);
-       if (status != IXGBE_SUCCESS)
-               return status;
+       if (hw->mac.ops.get_media_type(hw) != ixgbe_media_type_copper)
+               return IXGBE_ERR_CONFIG;
 
-       /* If there was no change in link status, we can just exit */
-       if (!(lasi & IXGBE_XENPAK_LASI_LINK_STATUS_ALARM))
-               return IXGBE_SUCCESS;
-
-       /* we read this twice back to back to indicate current status */
+       /* read this twice back to back to indicate current status */
        status = hw->phy.ops.read_reg(hw, IXGBE_MDIO_AUTO_NEG_STATUS,
                                      IXGBE_MDIO_AUTO_NEG_DEV_TYPE,
                                      &autoneg_status);
@@ -1578,9 +1571,9 @@ s32 ixgbe_setup_internal_phy_x550em(struct ixgbe_hw *hw)
        if (status != IXGBE_SUCCESS)
                return status;
 
-       /* If link is not up return an error indicating treat link as down */
+       /* If link is not up, then there is no setup necessary so return  */
        if (!(autoneg_status & IXGBE_MDIO_AUTO_NEG_LINK_STATUS))
-               return IXGBE_ERR_INVALID_LINK_SETTINGS;
+               return IXGBE_SUCCESS;
 
        status = hw->phy.ops.read_reg(hw, IXGBE_MDIO_AUTO_NEG_VENDOR_STAT,
                                      IXGBE_MDIO_AUTO_NEG_DEV_TYPE,