mac->ops.dmac_config = ixgbe_dmac_config_X550;
mac->ops.dmac_config_tcs = ixgbe_dmac_config_tcs_X550;
mac->ops.dmac_update_tcs = ixgbe_dmac_update_tcs_X550;
- mac->ops.setup_eee = ixgbe_setup_eee_X550;
+ mac->ops.setup_eee = NULL;
mac->ops.set_source_address_pruning =
ixgbe_set_source_address_pruning_X550;
mac->ops.set_ethertype_anti_spoofing =
mac->ops.mdd_event = ixgbe_mdd_event_X550;
mac->ops.restore_mdd_vf = ixgbe_restore_mdd_vf_X550;
mac->ops.disable_rx = ixgbe_disable_rx_x550;
+ /* Manageability interface */
+ mac->ops.set_fw_drv_ver = ixgbe_set_fw_drv_ver_x550;
switch (hw->device_id) {
case IXGBE_DEV_ID_X550EM_X_10G_T:
case IXGBE_DEV_ID_X550EM_A_10G_T:
hw->phy.type = ixgbe_phy_x550em_kr;
break;
case IXGBE_DEV_ID_X550EM_A_10G_T:
- case IXGBE_DEV_ID_X550EM_A_1G_T:
- case IXGBE_DEV_ID_X550EM_A_1G_T_L:
case IXGBE_DEV_ID_X550EM_X_1G_T:
case IXGBE_DEV_ID_X550EM_X_10G_T:
return ixgbe_identify_phy_generic(hw);
+ case IXGBE_DEV_ID_X550EM_A_1G_T:
+ case IXGBE_DEV_ID_X550EM_A_1G_T_L:
+ hw->phy.type = ixgbe_phy_fw;
+ hw->phy.ops.read_reg = NULL;
+ hw->phy.ops.write_reg = NULL;
+ if (hw->bus.lan_id)
+ hw->phy.phy_semaphore_mask |= IXGBE_GSSR_PHY1_SM;
+ else
+ hw->phy.phy_semaphore_mask |= IXGBE_GSSR_PHY0_SM;
+ break;
default:
break;
}
return IXGBE_SUCCESS;
}
+/**
+ * ixgbe_fw_phy_activity - Perform an activity on a PHY
+ * @hw: pointer to hardware structure
+ * @activity: activity to perform
+ * @data: Pointer to 4 32-bit words of data
+ */
+s32 ixgbe_fw_phy_activity(struct ixgbe_hw *hw, u16 activity,
+ u32 (*data)[FW_PHY_ACT_DATA_COUNT])
+{
+ union {
+ struct ixgbe_hic_phy_activity_req cmd;
+ struct ixgbe_hic_phy_activity_resp rsp;
+ } hic;
+ u16 retries = FW_PHY_ACT_RETRIES;
+ s32 rc;
+ u16 i;
+
+ do {
+ memset(&hic, 0, sizeof(hic));
+ hic.cmd.hdr.cmd = FW_PHY_ACT_REQ_CMD;
+ hic.cmd.hdr.buf_len = FW_PHY_ACT_REQ_LEN;
+ hic.cmd.hdr.checksum = FW_DEFAULT_CHECKSUM;
+ hic.cmd.port_number = hw->bus.lan_id;
+ hic.cmd.activity_id = IXGBE_CPU_TO_LE16(activity);
+ for (i = 0; i < FW_PHY_ACT_DATA_COUNT; ++i)
+ hic.cmd.data[i] = IXGBE_CPU_TO_BE32((*data)[i]);
+
+ rc = ixgbe_host_interface_command(hw, (u32 *)&hic.cmd,
+ sizeof(hic.cmd),
+ IXGBE_HI_COMMAND_TIMEOUT,
+ true);
+ if (rc != IXGBE_SUCCESS)
+ return rc;
+ if (hic.rsp.hdr.cmd_or_resp.ret_status ==
+ FW_CEM_RESP_STATUS_SUCCESS) {
+ for (i = 0; i < FW_PHY_ACT_DATA_COUNT; ++i)
+ (*data)[i] = IXGBE_BE32_TO_CPU(hic.rsp.data[i]);
+ return IXGBE_SUCCESS;
+ }
+ usec_delay(20);
+ --retries;
+ } while (retries > 0);
+
+ return IXGBE_ERR_HOST_INTERFACE_COMMAND;
+}
+
+static const struct {
+ u16 fw_speed;
+ ixgbe_link_speed phy_speed;
+} ixgbe_fw_map[] = {
+ { FW_PHY_ACT_LINK_SPEED_10, IXGBE_LINK_SPEED_10_FULL },
+ { FW_PHY_ACT_LINK_SPEED_100, IXGBE_LINK_SPEED_100_FULL },
+ { FW_PHY_ACT_LINK_SPEED_1G, IXGBE_LINK_SPEED_1GB_FULL },
+ { FW_PHY_ACT_LINK_SPEED_2_5G, IXGBE_LINK_SPEED_2_5GB_FULL },
+ { FW_PHY_ACT_LINK_SPEED_5G, IXGBE_LINK_SPEED_5GB_FULL },
+ { FW_PHY_ACT_LINK_SPEED_10G, IXGBE_LINK_SPEED_10GB_FULL },
+};
+
+/**
+ * ixgbe_get_phy_id_fw - Get the phy ID via firmware command
+ * @hw: pointer to hardware structure
+ *
+ * Returns error code
+ */
+static s32 ixgbe_get_phy_id_fw(struct ixgbe_hw *hw)
+{
+ u32 info[FW_PHY_ACT_DATA_COUNT] = { 0 };
+ u16 phy_speeds;
+ u16 phy_id_lo;
+ s32 rc;
+ u16 i;
+
+ rc = ixgbe_fw_phy_activity(hw, FW_PHY_ACT_GET_PHY_INFO, &info);
+ if (rc)
+ return rc;
+
+ hw->phy.speeds_supported = 0;
+ phy_speeds = info[0] & FW_PHY_INFO_SPEED_MASK;
+ for (i = 0; i < sizeof(ixgbe_fw_map) / sizeof(ixgbe_fw_map[0]); ++i) {
+ if (phy_speeds & ixgbe_fw_map[i].fw_speed)
+ hw->phy.speeds_supported |= ixgbe_fw_map[i].phy_speed;
+ }
+ if (!hw->phy.autoneg_advertised)
+ hw->phy.autoneg_advertised = hw->phy.speeds_supported;
+
+ hw->phy.id = info[0] & FW_PHY_INFO_ID_HI_MASK;
+ phy_id_lo = info[1] & FW_PHY_INFO_ID_LO_MASK;
+ hw->phy.id |= phy_id_lo & IXGBE_PHY_REVISION_MASK;
+ hw->phy.revision = phy_id_lo & ~IXGBE_PHY_REVISION_MASK;
+ if (!hw->phy.id || hw->phy.id == IXGBE_PHY_REVISION_MASK)
+ return IXGBE_ERR_PHY_ADDR_INVALID;
+ return IXGBE_SUCCESS;
+}
+
+/**
+ * ixgbe_identify_phy_fw - Get PHY type based on firmware command
+ * @hw: pointer to hardware structure
+ *
+ * Returns error code
+ */
+static s32 ixgbe_identify_phy_fw(struct ixgbe_hw *hw)
+{
+ if (hw->bus.lan_id)
+ hw->phy.phy_semaphore_mask = IXGBE_GSSR_PHY1_SM;
+ else
+ hw->phy.phy_semaphore_mask = IXGBE_GSSR_PHY0_SM;
+
+ hw->phy.type = ixgbe_phy_fw;
+ hw->phy.ops.read_reg = NULL;
+ hw->phy.ops.write_reg = NULL;
+ return ixgbe_get_phy_id_fw(hw);
+}
+
+/**
+ * ixgbe_shutdown_fw_phy - Shutdown a firmware-controlled PHY
+ * @hw: pointer to hardware structure
+ *
+ * Returns error code
+ */
+s32 ixgbe_shutdown_fw_phy(struct ixgbe_hw *hw)
+{
+ u32 setup[FW_PHY_ACT_DATA_COUNT] = { 0 };
+
+ setup[0] = FW_PHY_ACT_FORCE_LINK_DOWN_OFF;
+ return ixgbe_fw_phy_activity(hw, FW_PHY_ACT_FORCE_LINK_DOWN, &setup);
+}
+
STATIC s32 ixgbe_read_phy_reg_x550em(struct ixgbe_hw *hw, u32 reg_addr,
u32 device_type, u16 *phy_data)
{
else
mac->ops.setup_fc = ixgbe_setup_fc_X550em;
+ /* PHY */
+ phy->ops.init = ixgbe_init_phy_ops_X550em;
switch (hw->device_id) {
- case IXGBE_DEV_ID_X550EM_X_KR:
- case IXGBE_DEV_ID_X550EM_A_KR:
- case IXGBE_DEV_ID_X550EM_A_KR_L:
+ case IXGBE_DEV_ID_X550EM_A_1G_T:
+ case IXGBE_DEV_ID_X550EM_A_1G_T_L:
+ mac->ops.setup_fc = NULL;
+ phy->ops.identify = ixgbe_identify_phy_fw;
+ phy->ops.set_phy_power = NULL;
+ phy->ops.get_firmware_version = NULL;
break;
default:
- mac->ops.setup_eee = NULL;
+ phy->ops.identify = ixgbe_identify_phy_x550em;
}
- /* PHY */
- phy->ops.init = ixgbe_init_phy_ops_X550em;
- phy->ops.identify = ixgbe_identify_phy_x550em;
if (mac->ops.get_media_type(hw) != ixgbe_media_type_copper)
phy->ops.set_phy_power = NULL;
return ret_val;
}
+/**
+ * ixgbe_setup_fw_link - Setup firmware-controlled PHYs
+ * @hw: pointer to hardware structure
+ */
+static s32 ixgbe_setup_fw_link(struct ixgbe_hw *hw)
+{
+ u32 setup[FW_PHY_ACT_DATA_COUNT] = { 0 };
+ s32 rc;
+ u16 i;
+
+ if (hw->phy.reset_disable || ixgbe_check_reset_blocked(hw))
+ return 0;
+
+ if (hw->fc.strict_ieee && hw->fc.requested_mode == ixgbe_fc_rx_pause) {
+ ERROR_REPORT1(IXGBE_ERROR_UNSUPPORTED,
+ "ixgbe_fc_rx_pause not valid in strict IEEE mode\n");
+ return IXGBE_ERR_INVALID_LINK_SETTINGS;
+ }
+
+ switch (hw->fc.requested_mode) {
+ case ixgbe_fc_full:
+ setup[0] |= FW_PHY_ACT_SETUP_LINK_PAUSE_RXTX <<
+ FW_PHY_ACT_SETUP_LINK_PAUSE_SHIFT;
+ break;
+ case ixgbe_fc_rx_pause:
+ setup[0] |= FW_PHY_ACT_SETUP_LINK_PAUSE_RX <<
+ FW_PHY_ACT_SETUP_LINK_PAUSE_SHIFT;
+ break;
+ case ixgbe_fc_tx_pause:
+ setup[0] |= FW_PHY_ACT_SETUP_LINK_PAUSE_TX <<
+ FW_PHY_ACT_SETUP_LINK_PAUSE_SHIFT;
+ break;
+ default:
+ break;
+ }
+
+ for (i = 0; i < sizeof(ixgbe_fw_map) / sizeof(ixgbe_fw_map[0]); ++i) {
+ if (hw->phy.autoneg_advertised & ixgbe_fw_map[i].phy_speed)
+ setup[0] |= ixgbe_fw_map[i].fw_speed;
+ }
+ setup[0] |= FW_PHY_ACT_SETUP_LINK_HP | FW_PHY_ACT_SETUP_LINK_AN;
+
+ if (hw->phy.eee_speeds_advertised)
+ setup[0] |= FW_PHY_ACT_SETUP_LINK_EEE;
+
+ rc = ixgbe_fw_phy_activity(hw, FW_PHY_ACT_SETUP_LINK, &setup);
+ if (rc)
+ return rc;
+ if (setup[0] == FW_PHY_ACT_SETUP_LINK_RSP_DOWN)
+ return IXGBE_ERR_OVERTEMP;
+ return IXGBE_SUCCESS;
+}
+
+/**
+ * ixgbe_fc_autoneg_fw _ Set up flow control for FW-controlled PHYs
+ * @hw: pointer to hardware structure
+ *
+ * Called at init time to set up flow control.
+ */
+static s32 ixgbe_fc_autoneg_fw(struct ixgbe_hw *hw)
+{
+ if (hw->fc.requested_mode == ixgbe_fc_default)
+ hw->fc.requested_mode = ixgbe_fc_full;
+
+ return ixgbe_setup_fw_link(hw);
+}
+
+/**
+ * ixgbe_setup_eee_fw - Enable/disable EEE support
+ * @hw: pointer to the HW structure
+ * @enable_eee: boolean flag to enable EEE
+ *
+ * Enable/disable EEE based on enable_eee flag.
+ * This function controls EEE for firmware-based PHY implementations.
+ */
+static s32 ixgbe_setup_eee_fw(struct ixgbe_hw *hw, bool enable_eee)
+{
+ if (!!hw->phy.eee_speeds_advertised == enable_eee)
+ return IXGBE_SUCCESS;
+ if (enable_eee)
+ hw->phy.eee_speeds_advertised = hw->phy.eee_speeds_supported;
+ else
+ hw->phy.eee_speeds_advertised = 0;
+ return hw->phy.ops.setup_link(hw);
+}
+
/**
* ixgbe_init_ops_X550EM_a - Inits func ptrs and MAC type
* @hw: pointer to hardware structure
switch (mac->ops.get_media_type(hw)) {
case ixgbe_media_type_fiber:
- mac->ops.setup_fc = ixgbe_setup_fc_fiber_x550em_a;
+ mac->ops.setup_fc = NULL;
mac->ops.fc_autoneg = ixgbe_fc_autoneg_fiber_x550em_a;
break;
case ixgbe_media_type_backplane:
if ((hw->device_id == IXGBE_DEV_ID_X550EM_A_1G_T) ||
(hw->device_id == IXGBE_DEV_ID_X550EM_A_1G_T_L)) {
mac->ops.fc_autoneg = ixgbe_fc_autoneg_sgmii_x550em_a;
- mac->ops.setup_fc = ixgbe_setup_fc_sgmii_x550em_a;
+ mac->ops.setup_fc = ixgbe_fc_autoneg_fw;
+ }
+
+ switch (hw->device_id) {
+ case IXGBE_DEV_ID_X550EM_A_KR:
+ case IXGBE_DEV_ID_X550EM_A_KR_L:
+ mac->ops.setup_eee = ixgbe_setup_eee_fw;
+ break;
+ default:
+ mac->ops.setup_eee = NULL;
}
return ret_val;
*/
STATIC s32 ixgbe_enable_eee_x550(struct ixgbe_hw *hw)
{
- u16 autoneg_eee_reg;
u32 link_reg;
s32 status;
- if (hw->mac.type == ixgbe_mac_X550) {
- /* Advertise EEE capability */
- hw->phy.ops.read_reg(hw, IXGBE_MDIO_AUTO_NEG_EEE_ADVT,
- IXGBE_MDIO_AUTO_NEG_DEV_TYPE,
- &autoneg_eee_reg);
-
- autoneg_eee_reg |= (IXGBE_AUTO_NEG_10GBASE_EEE_ADVT |
- IXGBE_AUTO_NEG_1000BASE_EEE_ADVT |
- IXGBE_AUTO_NEG_100BASE_EEE_ADVT);
-
- hw->phy.ops.write_reg(hw, IXGBE_MDIO_AUTO_NEG_EEE_ADVT,
- IXGBE_MDIO_AUTO_NEG_DEV_TYPE,
- autoneg_eee_reg);
- return IXGBE_SUCCESS;
- }
-
switch (hw->device_id) {
- case IXGBE_DEV_ID_X550EM_X_KR:
case IXGBE_DEV_ID_X550EM_A_KR:
case IXGBE_DEV_ID_X550EM_A_KR_L:
status = hw->mac.ops.read_iosf_sb_reg(hw,
- IXGBE_KRM_LINK_CTRL_1(hw->bus.lan_id),
- IXGBE_SB_IOSF_TARGET_KR_PHY, &link_reg);
+ IXGBE_KRM_LINK_CTRL_1(hw->bus.lan_id),
+ IXGBE_SB_IOSF_TARGET_KR_PHY, &link_reg);
if (status != IXGBE_SUCCESS)
return status;
link_reg |= IXGBE_KRM_LINK_CTRL_1_TETH_EEE_CAP_KR |
- IXGBE_KRM_LINK_CTRL_1_TETH_EEE_CAP_KX;
+ IXGBE_KRM_LINK_CTRL_1_TETH_EEE_CAP_KX;
/* Don't advertise FEC capability when EEE enabled. */
link_reg &= ~IXGBE_KRM_LINK_CTRL_1_TETH_AN_CAP_FEC;
status = hw->mac.ops.write_iosf_sb_reg(hw,
- IXGBE_KRM_LINK_CTRL_1(hw->bus.lan_id),
- IXGBE_SB_IOSF_TARGET_KR_PHY, link_reg);
+ IXGBE_KRM_LINK_CTRL_1(hw->bus.lan_id),
+ IXGBE_SB_IOSF_TARGET_KR_PHY, link_reg);
if (status != IXGBE_SUCCESS)
return status;
break;
*/
STATIC s32 ixgbe_disable_eee_x550(struct ixgbe_hw *hw)
{
- u16 autoneg_eee_reg;
u32 link_reg;
s32 status;
- if (hw->mac.type == ixgbe_mac_X550) {
- /* Disable advertised EEE capability */
- hw->phy.ops.read_reg(hw, IXGBE_MDIO_AUTO_NEG_EEE_ADVT,
- IXGBE_MDIO_AUTO_NEG_DEV_TYPE,
- &autoneg_eee_reg);
-
- autoneg_eee_reg &= ~(IXGBE_AUTO_NEG_10GBASE_EEE_ADVT |
- IXGBE_AUTO_NEG_1000BASE_EEE_ADVT |
- IXGBE_AUTO_NEG_100BASE_EEE_ADVT);
-
- hw->phy.ops.write_reg(hw, IXGBE_MDIO_AUTO_NEG_EEE_ADVT,
- IXGBE_MDIO_AUTO_NEG_DEV_TYPE,
- autoneg_eee_reg);
- return IXGBE_SUCCESS;
- }
-
switch (hw->device_id) {
case IXGBE_DEV_ID_X550EM_X_KR:
case IXGBE_DEV_ID_X550EM_A_KR:
case IXGBE_DEV_ID_X550EM_A_KR_L:
status = hw->mac.ops.read_iosf_sb_reg(hw,
- IXGBE_KRM_LINK_CTRL_1(hw->bus.lan_id),
- IXGBE_SB_IOSF_TARGET_KR_PHY, &link_reg);
+ IXGBE_KRM_LINK_CTRL_1(hw->bus.lan_id),
+ IXGBE_SB_IOSF_TARGET_KR_PHY, &link_reg);
if (status != IXGBE_SUCCESS)
return status;
link_reg |= IXGBE_KRM_LINK_CTRL_1_TETH_AN_CAP_FEC;
status = hw->mac.ops.write_iosf_sb_reg(hw,
- IXGBE_KRM_LINK_CTRL_1(hw->bus.lan_id),
- IXGBE_SB_IOSF_TARGET_KR_PHY, link_reg);
+ IXGBE_KRM_LINK_CTRL_1(hw->bus.lan_id),
+ IXGBE_SB_IOSF_TARGET_KR_PHY, link_reg);
if (status != IXGBE_SUCCESS)
return status;
break;
if (enable_eee) {
eeer |= (IXGBE_EEER_TX_LPI_EN | IXGBE_EEER_RX_LPI_EN);
- /* Not supported on first revision of X550EM_x. */
- if ((hw->mac.type == ixgbe_mac_X550EM_x) &&
- !(IXGBE_FUSES0_REV_MASK &
- IXGBE_READ_REG(hw, IXGBE_FUSES0_GROUP(0))))
- return IXGBE_SUCCESS;
status = ixgbe_enable_eee_x550(hw);
if (status)
return status;
return hw->phy.ops.setup_link_speed(hw, speed, autoneg_wait);
}
- /**
- * ixgbe_setup_sgmii_m88 - Set up link for sgmii with Marvell PHYs
+/**
+ * ixgbe_setup_sgmii_fw - Set up link for sgmii with firmware-controlled PHYs
* @hw: pointer to hardware structure
*/
-STATIC s32 ixgbe_setup_sgmii_m88(struct ixgbe_hw *hw, ixgbe_link_speed speed,
- bool autoneg_wait)
+STATIC s32 ixgbe_setup_sgmii_fw(struct ixgbe_hw *hw, ixgbe_link_speed speed,
+ bool autoneg_wait)
{
struct ixgbe_mac_info *mac = &hw->mac;
u32 lval, sval, flx_val;
return rc;
flx_val &= ~IXGBE_KRM_PMD_FLX_MASK_ST20_SPEED_MASK;
- flx_val |= IXGBE_KRM_PMD_FLX_MASK_ST20_SPEED_1G;
+ flx_val |= IXGBE_KRM_PMD_FLX_MASK_ST20_SPEED_AN;
flx_val &= ~IXGBE_KRM_PMD_FLX_MASK_ST20_AN_EN;
flx_val |= IXGBE_KRM_PMD_FLX_MASK_ST20_SGMII_EN;
flx_val |= IXGBE_KRM_PMD_FLX_MASK_ST20_AN37_EN;
mac->ops.setup_link = ixgbe_setup_mac_link_multispeed_fiber;
mac->ops.set_rate_select_speed =
ixgbe_set_soft_rate_select_speed;
+
if ((hw->device_id == IXGBE_DEV_ID_X550EM_A_SFP_N) ||
(hw->device_id == IXGBE_DEV_ID_X550EM_A_SFP))
mac->ops.setup_mac_link =
- ixgbe_setup_mac_link_sfp_x550a;
+ ixgbe_setup_mac_link_sfp_x550a;
else
mac->ops.setup_mac_link =
- ixgbe_setup_mac_link_sfp_x550em;
+ ixgbe_setup_mac_link_sfp_x550em;
break;
case ixgbe_media_type_copper:
if (hw->mac.type == ixgbe_mac_X550EM_a) {
if (hw->device_id == IXGBE_DEV_ID_X550EM_A_1G_T ||
hw->device_id == IXGBE_DEV_ID_X550EM_A_1G_T_L) {
- mac->ops.setup_link = ixgbe_setup_sgmii_m88;
+ mac->ops.setup_link = ixgbe_setup_sgmii_fw;
+ mac->ops.check_link =
+ ixgbe_check_mac_link_generic;
} else {
mac->ops.setup_link =
ixgbe_setup_mac_link_t_X550em;
{
DEBUGFUNC("ixgbe_get_link_capabilities_X550em");
+
+ if (hw->phy.type == ixgbe_phy_fw) {
+ *autoneg = true;
+ *speed = hw->phy.speeds_supported;
+ return 0;
+ }
+
/* SFP */
if (hw->phy.media_type == ixgbe_media_type_fiber) {
*speed = IXGBE_LINK_SPEED_10GB_FULL;
} else {
switch (hw->phy.type) {
- case ixgbe_phy_m88:
- *speed = IXGBE_LINK_SPEED_1GB_FULL |
- IXGBE_LINK_SPEED_100_FULL |
- IXGBE_LINK_SPEED_10_FULL;
- break;
case ixgbe_phy_sgmii:
*speed = IXGBE_LINK_SPEED_1GB_FULL;
break;
+ case ixgbe_phy_x550em_kr:
+ if (hw->mac.type == ixgbe_mac_X550EM_a) {
+ /* check different backplane modes */
+ if (hw->phy.nw_mng_if_sel &
+ IXGBE_NW_MNG_IF_SEL_PHY_SPEED_2_5G) {
+ *speed = IXGBE_LINK_SPEED_2_5GB_FULL;
+ break;
+ } else if (hw->device_id ==
+ IXGBE_DEV_ID_X550EM_A_KR_L) {
+ *speed = IXGBE_LINK_SPEED_1GB_FULL;
+ break;
+ }
+ }
+ /* fall through */
default:
*speed = IXGBE_LINK_SPEED_10GB_FULL |
IXGBE_LINK_SPEED_1GB_FULL;
status = ixgbe_get_lasi_ext_t_x550em(hw, &lsc);
/* Enable link status change alarm */
- status = hw->phy.ops.read_reg(hw, IXGBE_MDIO_PMA_TX_VEN_LASI_INT_MASK,
- IXGBE_MDIO_AUTO_NEG_DEV_TYPE, ®);
- if (status != IXGBE_SUCCESS)
- return status;
+ /* Enable the LASI interrupts on X552 devices to receive notifications
+ * of the link configurations of the external PHY and correspondingly
+ * support the configuration of the internal iXFI link, since iXFI does
+ * not support auto-negotiation. This is not required for X553 devices
+ * having KR support, which performs auto-negotiations and which is used
+ * as the internal link to the external PHY. Hence adding a check here
+ * to avoid enabling LASI interrupts for X553 devices.
+ */
+ if (hw->mac.type != ixgbe_mac_X550EM_a) {
+ status = hw->phy.ops.read_reg(hw,
+ IXGBE_MDIO_PMA_TX_VEN_LASI_INT_MASK,
+ IXGBE_MDIO_AUTO_NEG_DEV_TYPE, ®);
- reg |= IXGBE_MDIO_PMA_TX_VEN_LASI_INT_EN;
+ if (status != IXGBE_SUCCESS)
+ return status;
- status = hw->phy.ops.write_reg(hw, IXGBE_MDIO_PMA_TX_VEN_LASI_INT_MASK,
- IXGBE_MDIO_AUTO_NEG_DEV_TYPE, reg);
+ reg |= IXGBE_MDIO_PMA_TX_VEN_LASI_INT_EN;
- if (status != IXGBE_SUCCESS)
- return status;
+ status = hw->phy.ops.write_reg(hw,
+ IXGBE_MDIO_PMA_TX_VEN_LASI_INT_MASK,
+ IXGBE_MDIO_AUTO_NEG_DEV_TYPE, reg);
+
+ if (status != IXGBE_SUCCESS)
+ return status;
+ }
/* Enable high temperature failure and global fault alarms */
status = hw->phy.ops.read_reg(hw, IXGBE_MDIO_GLOBAL_INT_MASK,
u32 reg_val;
status = hw->mac.ops.read_iosf_sb_reg(hw,
- IXGBE_KRM_LINK_CTRL_1(hw->bus.lan_id),
- IXGBE_SB_IOSF_TARGET_KR_PHY, ®_val);
+ IXGBE_KRM_LINK_CTRL_1(hw->bus.lan_id),
+ IXGBE_SB_IOSF_TARGET_KR_PHY, ®_val);
if (status)
return status;
reg_val |= IXGBE_KRM_LINK_CTRL_1_TETH_AN_CAP_KX;
status = hw->mac.ops.write_iosf_sb_reg(hw,
- IXGBE_KRM_LINK_CTRL_1(hw->bus.lan_id),
- IXGBE_SB_IOSF_TARGET_KR_PHY, reg_val);
+ IXGBE_KRM_LINK_CTRL_1(hw->bus.lan_id),
+ IXGBE_SB_IOSF_TARGET_KR_PHY, reg_val);
- if (status)
- return status;
+ if (hw->mac.type == ixgbe_mac_X550EM_a) {
+ /* Set lane mode to KR auto negotiation */
+ status = hw->mac.ops.read_iosf_sb_reg(hw,
+ IXGBE_KRM_PMD_FLX_MASK_ST20(hw->bus.lan_id),
+ IXGBE_SB_IOSF_TARGET_KR_PHY, ®_val);
- reg_val &= ~IXGBE_KRM_PMD_FLX_MASK_ST20_SPEED_MASK;
- reg_val |= IXGBE_KRM_PMD_FLX_MASK_ST20_SPEED_AN;
- reg_val |= IXGBE_KRM_PMD_FLX_MASK_ST20_AN_EN;
- reg_val &= ~IXGBE_KRM_PMD_FLX_MASK_ST20_AN37_EN;
- reg_val &= ~IXGBE_KRM_PMD_FLX_MASK_ST20_SGMII_EN;
+ if (status)
+ return status;
- status = hw->mac.ops.write_iosf_sb_reg(hw,
+ reg_val &= ~IXGBE_KRM_PMD_FLX_MASK_ST20_SPEED_MASK;
+ reg_val |= IXGBE_KRM_PMD_FLX_MASK_ST20_SPEED_AN;
+ reg_val |= IXGBE_KRM_PMD_FLX_MASK_ST20_AN_EN;
+ reg_val &= ~IXGBE_KRM_PMD_FLX_MASK_ST20_AN37_EN;
+ reg_val &= ~IXGBE_KRM_PMD_FLX_MASK_ST20_SGMII_EN;
+
+ status = hw->mac.ops.write_iosf_sb_reg(hw,
IXGBE_KRM_PMD_FLX_MASK_ST20(hw->bus.lan_id),
IXGBE_SB_IOSF_TARGET_KR_PHY, reg_val);
+ }
return ixgbe_restart_an_internal_phy_x550em(hw);
}
/**
- * ixgbe_setup_m88 - setup m88 PHY
+ * ixgbe_reset_phy_fw - Reset firmware-controlled PHYs
* @hw: pointer to hardware structure
*/
-STATIC s32 ixgbe_setup_m88(struct ixgbe_hw *hw)
+static s32 ixgbe_reset_phy_fw(struct ixgbe_hw *hw)
{
- u32 mask = hw->phy.phy_semaphore_mask | IXGBE_GSSR_TOKEN_SM;
- u16 reg;
+ u32 store[FW_PHY_ACT_DATA_COUNT] = { 0 };
s32 rc;
if (hw->phy.reset_disable || ixgbe_check_reset_blocked(hw))
return IXGBE_SUCCESS;
- rc = hw->mac.ops.acquire_swfw_sync(hw, mask);
+ rc = ixgbe_fw_phy_activity(hw, FW_PHY_ACT_PHY_SW_RESET, &store);
if (rc)
return rc;
+ memset(store, 0, sizeof(store));
- rc = hw->phy.ops.read_reg_mdi(hw, IXGBE_M88E1500_COPPER_CTRL, 0, ®);
- if (rc)
- goto out;
- if (reg & IXGBE_M88E1500_COPPER_CTRL_POWER_DOWN) {
- reg &= ~IXGBE_M88E1500_COPPER_CTRL_POWER_DOWN;
- hw->phy.ops.write_reg_mdi(hw, IXGBE_M88E1500_COPPER_CTRL, 0,
- reg);
- }
-
- rc = hw->phy.ops.read_reg_mdi(hw, IXGBE_M88E1500_MAC_CTRL_1, 0, ®);
- if (rc)
- goto out;
- if (reg & IXGBE_M88E1500_MAC_CTRL_1_POWER_DOWN) {
- reg &= ~IXGBE_M88E1500_MAC_CTRL_1_POWER_DOWN;
- hw->phy.ops.write_reg_mdi(hw, IXGBE_M88E1500_MAC_CTRL_1, 0,
- reg);
- }
-
- rc = hw->phy.ops.write_reg_mdi(hw, IXGBE_M88E1500_PAGE_ADDR, 0, 2);
- if (rc)
- goto out;
-
- rc = hw->phy.ops.read_reg_mdi(hw, IXGBE_M88E1500_MAC_SPEC_CTRL, 0,
- ®);
- if (rc)
- goto out;
- if (reg & IXGBE_M88E1500_MAC_SPEC_CTRL_POWER_DOWN) {
- reg &= ~IXGBE_M88E1500_MAC_SPEC_CTRL_POWER_DOWN;
- hw->phy.ops.write_reg_mdi(hw, IXGBE_M88E1500_MAC_SPEC_CTRL, 0,
- reg);
- rc = hw->phy.ops.write_reg_mdi(hw, IXGBE_M88E1500_PAGE_ADDR, 0,
- 0);
- if (rc)
- goto out;
- rc = hw->phy.ops.read_reg_mdi(hw, IXGBE_M88E1500_COPPER_CTRL, 0,
- ®);
- if (rc)
- goto out;
- reg |= IXGBE_M88E1500_COPPER_CTRL_RESET;
- hw->phy.ops.write_reg_mdi(hw, IXGBE_M88E1500_COPPER_CTRL, 0,
- reg);
- usec_delay(50);
- } else {
- rc = hw->phy.ops.write_reg_mdi(hw, IXGBE_M88E1500_PAGE_ADDR, 0,
- 0);
- if (rc)
- goto out;
- }
-
- rc = hw->phy.ops.read_reg_mdi(hw, IXGBE_M88E1500_COPPER_CTRL, 0, ®);
- if (rc)
- goto out;
-
- if (!(reg & IXGBE_M88E1500_COPPER_CTRL_AN_EN)) {
- reg |= IXGBE_M88E1500_COPPER_CTRL_AN_EN;
- hw->phy.ops.write_reg_mdi(hw, IXGBE_M88E1500_COPPER_CTRL, 0,
- reg);
- }
-
- rc = hw->phy.ops.read_reg_mdi(hw, IXGBE_M88E1500_1000T_CTRL, 0, ®);
- if (rc)
- goto out;
- reg &= ~IXGBE_M88E1500_1000T_CTRL_HALF_DUPLEX;
- reg &= ~IXGBE_M88E1500_1000T_CTRL_FULL_DUPLEX;
- if (hw->phy.autoneg_advertised & IXGBE_LINK_SPEED_1GB_FULL)
- reg |= IXGBE_M88E1500_1000T_CTRL_FULL_DUPLEX;
- hw->phy.ops.write_reg_mdi(hw, IXGBE_M88E1500_1000T_CTRL, 0, reg);
-
- rc = hw->phy.ops.read_reg_mdi(hw, IXGBE_M88E1500_COPPER_AN, 0, ®);
- if (rc)
- goto out;
- reg &= ~IXGBE_M88E1500_COPPER_AN_T4;
- reg &= ~IXGBE_M88E1500_COPPER_AN_100TX_FD;
- reg &= ~IXGBE_M88E1500_COPPER_AN_100TX_HD;
- reg &= ~IXGBE_M88E1500_COPPER_AN_10TX_FD;
- reg &= ~IXGBE_M88E1500_COPPER_AN_10TX_HD;
-
- /* Flow control auto negotiation configuration was moved from here to
- * the function ixgbe_setup_fc_sgmii_x550em_a()
- */
-
- if (hw->phy.autoneg_advertised & IXGBE_LINK_SPEED_100_FULL)
- reg |= IXGBE_M88E1500_COPPER_AN_100TX_FD;
- if (hw->phy.autoneg_advertised & IXGBE_LINK_SPEED_10_FULL)
- reg |= IXGBE_M88E1500_COPPER_AN_10TX_FD;
- hw->phy.ops.write_reg_mdi(hw, IXGBE_M88E1500_COPPER_AN, 0, reg);
-
- rc = hw->phy.ops.read_reg_mdi(hw, IXGBE_M88E1500_COPPER_CTRL, 0, ®);
+ rc = ixgbe_fw_phy_activity(hw, FW_PHY_ACT_INIT_PHY, &store);
if (rc)
- goto out;
- reg |= IXGBE_M88E1500_COPPER_CTRL_RESTART_AN;
- hw->phy.ops.write_reg_mdi(hw, IXGBE_M88E1500_COPPER_CTRL, 0, reg);
-
-
- hw->mac.ops.release_swfw_sync(hw, mask);
- return rc;
+ return rc;
-out:
- hw->phy.ops.write_reg_mdi(hw, IXGBE_M88E1500_PAGE_ADDR, 0, 0);
- hw->mac.ops.release_swfw_sync(hw, mask);
- return rc;
+ return ixgbe_setup_fw_link(hw);
}
/**
- * ixgbe_reset_phy_m88e1500 - Reset m88e1500 PHY
+ * ixgbe_check_overtemp_fw - Check firmware-controlled PHYs for overtemp
* @hw: pointer to hardware structure
- *
- * The PHY token must be held when calling this function.
*/
-static s32 ixgbe_reset_phy_m88e1500(struct ixgbe_hw *hw)
+static s32 ixgbe_check_overtemp_fw(struct ixgbe_hw *hw)
{
- u16 reg;
+ u32 store[FW_PHY_ACT_DATA_COUNT] = { 0 };
s32 rc;
- rc = hw->phy.ops.write_reg_mdi(hw, IXGBE_M88E1500_PAGE_ADDR, 0, 0);
- if (rc)
- return rc;
-
- rc = hw->phy.ops.read_reg_mdi(hw, IXGBE_M88E1500_COPPER_CTRL, 0, ®);
+ rc = ixgbe_fw_phy_activity(hw, FW_PHY_ACT_GET_LINK_INFO, &store);
if (rc)
return rc;
- reg |= IXGBE_M88E1500_COPPER_CTRL_RESET;
- rc = hw->phy.ops.write_reg_mdi(hw, IXGBE_M88E1500_COPPER_CTRL, 0, reg);
-
- usec_delay(10);
-
- return rc;
+ if (store[0] & FW_PHY_ACT_GET_LINK_INFO_TEMP) {
+ ixgbe_shutdown_fw_phy(hw);
+ return IXGBE_ERR_OVERTEMP;
+ }
+ return IXGBE_SUCCESS;
}
/**
- * ixgbe_reset_phy_m88e1543 - Reset m88e1543 PHY
- * @hw: pointer to hardware structure
+ * ixgbe_read_mng_if_sel_x550em - Read NW_MNG_IF_SEL register
+ * @hw: pointer to hardware structure
*
- * The PHY token must be held when calling this function.
- */
-static s32 ixgbe_reset_phy_m88e1543(struct ixgbe_hw *hw)
+ * Read NW_MNG_IF_SEL register and save field values, and check for valid field
+ * values.
+ **/
+STATIC s32 ixgbe_read_mng_if_sel_x550em(struct ixgbe_hw *hw)
{
- return hw->phy.ops.write_reg_mdi(hw, IXGBE_M88E1500_PAGE_ADDR, 0, 0);
-}
-
-/**
- * ixgbe_reset_phy_m88 - Reset m88 PHY
- * @hw: pointer to hardware structure
- */
-STATIC s32 ixgbe_reset_phy_m88(struct ixgbe_hw *hw)
-{
- u32 mask = hw->phy.phy_semaphore_mask | IXGBE_GSSR_TOKEN_SM;
- u16 reg;
- s32 rc;
-
- if (hw->phy.reset_disable || ixgbe_check_reset_blocked(hw))
- return IXGBE_SUCCESS;
-
- rc = hw->mac.ops.acquire_swfw_sync(hw, mask);
- if (rc)
- return rc;
-
- switch (hw->phy.id) {
- case IXGBE_M88E1500_E_PHY_ID:
- rc = ixgbe_reset_phy_m88e1500(hw);
- break;
- case IXGBE_M88E1543_E_PHY_ID:
- rc = ixgbe_reset_phy_m88e1543(hw);
- break;
- default:
- rc = IXGBE_ERR_PHY;
- break;
- }
-
- rc = hw->phy.ops.write_reg_mdi(hw, IXGBE_M88E1500_PAGE_ADDR, 0, 1);
- if (rc)
- goto out;
-
- reg = IXGBE_M88E1500_FIBER_CTRL_RESET |
- IXGBE_M88E1500_FIBER_CTRL_DUPLEX_FULL |
- IXGBE_M88E1500_FIBER_CTRL_SPEED_MSB;
- rc = hw->phy.ops.write_reg_mdi(hw, IXGBE_M88E1500_FIBER_CTRL, 0, reg);
- if (rc)
- goto out;
-
- rc = hw->phy.ops.write_reg_mdi(hw, IXGBE_M88E1500_PAGE_ADDR, 0, 18);
- if (rc)
- goto out;
-
- reg = IXGBE_M88E1500_GEN_CTRL_RESET |
- IXGBE_M88E1500_GEN_CTRL_MODE_SGMII_COPPER;
- rc = hw->phy.ops.write_reg_mdi(hw, IXGBE_M88E1500_GEN_CTRL, 0, reg);
- if (rc)
- goto out;
-
- rc = hw->phy.ops.write_reg_mdi(hw, IXGBE_M88E1500_PAGE_ADDR, 0, 1);
- if (rc)
- goto out;
-
- reg = IXGBE_M88E1500_FIBER_CTRL_RESET |
- IXGBE_M88E1500_FIBER_CTRL_AN_EN |
- IXGBE_M88E1500_FIBER_CTRL_DUPLEX_FULL |
- IXGBE_M88E1500_FIBER_CTRL_SPEED_MSB;
- rc = hw->phy.ops.write_reg_mdi(hw, IXGBE_M88E1500_FIBER_CTRL, 0, reg);
- if (rc)
- goto out;
-
- rc = hw->phy.ops.write_reg_mdi(hw, IXGBE_M88E1500_PAGE_ADDR, 0, 0);
- if (rc)
- goto out;
-
- reg = (IXGBE_M88E1500_MAC_CTRL_1_DWN_4X <<
- IXGBE_M88E1500_MAC_CTRL_1_DWN_SHIFT) |
- (IXGBE_M88E1500_MAC_CTRL_1_ED_TM <<
- IXGBE_M88E1500_MAC_CTRL_1_ED_SHIFT) |
- (IXGBE_M88E1500_MAC_CTRL_1_MDIX_AUTO <<
- IXGBE_M88E1500_MAC_CTRL_1_MDIX_SHIFT);
- rc = hw->phy.ops.write_reg_mdi(hw, IXGBE_M88E1500_MAC_CTRL_1, 0, reg);
- if (rc)
- goto out;
-
- reg = IXGBE_M88E1500_COPPER_CTRL_RESET |
- IXGBE_M88E1500_COPPER_CTRL_AN_EN |
- IXGBE_M88E1500_COPPER_CTRL_RESTART_AN |
- IXGBE_M88E1500_COPPER_CTRL_FULL_DUPLEX |
- IXGBE_M88E1500_COPPER_CTRL_SPEED_MSB;
- rc = hw->phy.ops.write_reg_mdi(hw, IXGBE_M88E1500_COPPER_CTRL, 0, reg);
- if (rc)
- goto out;
-
- hw->mac.ops.release_swfw_sync(hw, mask);
-
- /* In case of first reset set advertised speeds to default value */
- if (!hw->phy.autoneg_advertised)
- hw->phy.autoneg_advertised = IXGBE_LINK_SPEED_1GB_FULL |
- IXGBE_LINK_SPEED_100_FULL |
- IXGBE_LINK_SPEED_10_FULL;
-
- return ixgbe_setup_m88(hw);
-
-out:
- hw->phy.ops.write_reg_mdi(hw, IXGBE_M88E1500_PAGE_ADDR, 0, 0);
- hw->mac.ops.release_swfw_sync(hw, mask);
- return rc;
-}
-
-/**
- * ixgbe_read_mng_if_sel_x550em - Read NW_MNG_IF_SEL register
- * @hw: pointer to hardware structure
- *
- * Read NW_MNG_IF_SEL register and save field values, and check for valid field
- * values.
- **/
-STATIC s32 ixgbe_read_mng_if_sel_x550em(struct ixgbe_hw *hw)
-{
- /* Save NW management interface connected on board. This is used
- * to determine internal PHY mode.
- */
- hw->phy.nw_mng_if_sel = IXGBE_READ_REG(hw, IXGBE_NW_MNG_IF_SEL);
+ /* Save NW management interface connected on board. This is used
+ * to determine internal PHY mode.
+ */
+ hw->phy.nw_mng_if_sel = IXGBE_READ_REG(hw, IXGBE_NW_MNG_IF_SEL);
/* If X552 (X550EM_a) and MDIO is connected to external PHY, then set
* PHY address. This register field was has only been used for X552.
hw->phy.nw_mng_if_sel & IXGBE_NW_MNG_IF_SEL_MDIO_ACT) {
hw->phy.addr = (hw->phy.nw_mng_if_sel &
IXGBE_NW_MNG_IF_SEL_MDIO_PHY_ADD) >>
- IXGBE_NW_MNG_IF_SEL_MDIO_PHY_ADD_SHIFT;
+ IXGBE_NW_MNG_IF_SEL_MDIO_PHY_ADD_SHIFT;
}
return IXGBE_SUCCESS;
DEBUGFUNC("ixgbe_init_phy_ops_X550em");
+ hw->mac.ops.set_lan_id(hw);
+ ixgbe_read_mng_if_sel_x550em(hw);
+
if (hw->mac.ops.get_media_type(hw) == ixgbe_media_type_fiber) {
phy->phy_semaphore_mask = IXGBE_GSSR_SHARED_I2C_SM;
ixgbe_setup_mux_ctl(hw);
phy->ops.write_reg_mdi = ixgbe_write_phy_reg_mdi_22;
hw->phy.ops.read_reg = ixgbe_read_phy_reg_x550a;
hw->phy.ops.write_reg = ixgbe_write_phy_reg_x550a;
+ phy->ops.check_overtemp = ixgbe_check_overtemp_fw;
if (hw->bus.lan_id)
hw->phy.phy_semaphore_mask |= IXGBE_GSSR_PHY1_SM;
else
/* Identify the PHY or SFP module */
ret_val = phy->ops.identify(hw);
- if (ret_val == IXGBE_ERR_SFP_NOT_SUPPORTED)
+ if (ret_val == IXGBE_ERR_SFP_NOT_SUPPORTED ||
+ ret_val == IXGBE_ERR_PHY_ADDR_INVALID)
return ret_val;
/* Setup function pointers based on detected hardware */
case ixgbe_phy_sgmii:
phy->ops.setup_link = NULL;
break;
- case ixgbe_phy_m88:
- phy->ops.setup_link = ixgbe_setup_m88;
- phy->ops.reset = ixgbe_reset_phy_m88;
+ case ixgbe_phy_fw:
+ phy->ops.setup_link = ixgbe_setup_fw_link;
+ phy->ops.reset = ixgbe_reset_phy_fw;
break;
default:
break;
case IXGBE_DEV_ID_X550EM_X_10G_T:
case IXGBE_DEV_ID_X550EM_A_SGMII:
case IXGBE_DEV_ID_X550EM_A_SGMII_L:
- case IXGBE_DEV_ID_X550EM_A_1G_T:
- case IXGBE_DEV_ID_X550EM_A_1G_T_L:
case IXGBE_DEV_ID_X550EM_A_10G_T:
case IXGBE_DEV_ID_X550EM_A_SFP:
case IXGBE_DEV_ID_X550EM_A_QSFP:
hlreg0 &= ~IXGBE_HLREG0_MDCSPD;
IXGBE_WRITE_REG(hw, IXGBE_HLREG0, hlreg0);
break;
+ case IXGBE_DEV_ID_X550EM_A_1G_T:
+ case IXGBE_DEV_ID_X550EM_A_1G_T_L:
+ /* Select fast MDIO clock speed for these devices */
+ hlreg0 = IXGBE_READ_REG(hw, IXGBE_HLREG0);
+ hlreg0 |= IXGBE_HLREG0_MDCSPD;
+ IXGBE_WRITE_REG(hw, IXGBE_HLREG0, hlreg0);
+ break;
default:
break;
}
return status;
/* Reset PHY */
- if (!hw->phy.reset_disable && hw->phy.ops.reset)
- hw->phy.ops.reset(hw);
+ if (!hw->phy.reset_disable && hw->phy.ops.reset) {
+ if (hw->phy.ops.reset(hw) == IXGBE_ERR_OVERTEMP)
+ return IXGBE_ERR_OVERTEMP;
+ }
mac_reset_top:
/* Issue global reset to the MAC. Needs to be SW reset if link is up.
if (ret_val != IXGBE_SUCCESS)
return ret_val;
- /* Configure internal PHY for KR/KX. */
- ixgbe_setup_kr_speed_x550em(hw, speed);
-
- /* Configure CS4227 LINE side to proper mode. */
- reg_slice = IXGBE_CS4227_LINE_SPARE24_LSB +
- (hw->bus.lan_id << 12);
- if (setup_linear)
- reg_val = (IXGBE_CS4227_EDC_MODE_CX1 << 1) | 0x1;
- else
+ if (!(hw->phy.nw_mng_if_sel & IXGBE_NW_MNG_IF_SEL_INT_PHY_MODE)) {
+ /* Configure CS4227 LINE side to 10G SR. */
+ reg_slice = IXGBE_CS4227_LINE_SPARE22_MSB +
+ (hw->bus.lan_id << 12);
+ reg_val = IXGBE_CS4227_SPEED_10G;
+ ret_val = hw->link.ops.write_link(hw, hw->link.addr, reg_slice,
+ reg_val);
+
+ reg_slice = IXGBE_CS4227_LINE_SPARE24_LSB +
+ (hw->bus.lan_id << 12);
reg_val = (IXGBE_CS4227_EDC_MODE_SR << 1) | 0x1;
- ret_val = hw->link.ops.write_link(hw, hw->link.addr, reg_slice,
- reg_val);
+ ret_val = hw->link.ops.write_link(hw, hw->link.addr, reg_slice,
+ reg_val);
+
+ /* Configure CS4227 for HOST connection rate then type. */
+ reg_slice = IXGBE_CS4227_HOST_SPARE22_MSB +
+ (hw->bus.lan_id << 12);
+ reg_val = (speed & IXGBE_LINK_SPEED_10GB_FULL) ?
+ IXGBE_CS4227_SPEED_10G : IXGBE_CS4227_SPEED_1G;
+ ret_val = hw->link.ops.write_link(hw, hw->link.addr, reg_slice,
+ reg_val);
+
+ reg_slice = IXGBE_CS4227_HOST_SPARE24_LSB +
+ (hw->bus.lan_id << 12);
+ if (setup_linear)
+ reg_val = (IXGBE_CS4227_EDC_MODE_CX1 << 1) | 0x1;
+ else
+ reg_val = (IXGBE_CS4227_EDC_MODE_SR << 1) | 0x1;
+ ret_val = hw->link.ops.write_link(hw, hw->link.addr, reg_slice,
+ reg_val);
+
+ /* Setup XFI internal link. */
+ ret_val = ixgbe_setup_ixfi_x550em(hw, &speed);
+ } else {
+ /* Configure internal PHY for KR/KX. */
+ ixgbe_setup_kr_speed_x550em(hw, speed);
+
+ /* Configure CS4227 LINE side to proper mode. */
+ reg_slice = IXGBE_CS4227_LINE_SPARE24_LSB +
+ (hw->bus.lan_id << 12);
+ if (setup_linear)
+ reg_val = (IXGBE_CS4227_EDC_MODE_CX1 << 1) | 0x1;
+ else
+ reg_val = (IXGBE_CS4227_EDC_MODE_SR << 1) | 0x1;
+ ret_val = hw->link.ops.write_link(hw, hw->link.addr, reg_slice,
+ reg_val);
+ }
return ret_val;
}
* Configure the the integrated PHY for SFP support.
**/
s32 ixgbe_setup_mac_link_sfp_x550a(struct ixgbe_hw *hw,
- ixgbe_link_speed speed,
- bool autoneg_wait_to_complete)
+ ixgbe_link_speed speed,
+ bool autoneg_wait_to_complete)
{
s32 ret_val;
u16 reg_phy_ext;
return IXGBE_ERR_PHY_ADDR_INVALID;
}
- /* Get external PHY device id */
- ret_val = hw->phy.ops.read_reg(hw, IXGBE_CS4227_GLOBAL_ID_MSB,
- IXGBE_MDIO_ZERO_DEV_TYPE, ®_phy_ext);
+ /* Get external PHY SKU id */
+ ret_val = hw->phy.ops.read_reg(hw, IXGBE_CS4227_EFUSE_PDF_SKU,
+ IXGBE_MDIO_ZERO_DEV_TYPE, ®_phy_ext);
if (ret_val != IXGBE_SUCCESS)
return ret_val;
/* When configuring quad port CS4223, the MAC instance is part
* of the slice offset.
*/
- if (reg_phy_ext == IXGBE_CS4223_PHY_ID)
+ if (reg_phy_ext == IXGBE_CS4223_SKU_ID)
slice_offset = (hw->bus.lan_id +
(hw->bus.instance_id << 1)) << 12;
else
else
reg_phy_ext = (IXGBE_CS4227_EDC_MODE_SR << 1) | 0x1;
ret_val = hw->phy.ops.write_reg(hw, reg_slice,
- IXGBE_MDIO_ZERO_DEV_TYPE, reg_phy_ext);
+ IXGBE_MDIO_ZERO_DEV_TYPE, reg_phy_ext);
}
return ret_val;
}
s32 status;
u32 reg_val;
+ /* iXFI is only supported with X552 */
+ if (mac->type != ixgbe_mac_X550EM_x)
+ return IXGBE_ERR_LINK_SETUP;
+
/* Disable AN and force speed to 10G Serial. */
status = mac->ops.read_iosf_sb_reg(hw,
IXGBE_KRM_LINK_CTRL_1(hw->bus.lan_id),
if (hw->mac.ops.get_media_type(hw) != ixgbe_media_type_copper)
return IXGBE_ERR_CONFIG;
- if (!(hw->phy.nw_mng_if_sel & IXGBE_NW_MNG_IF_SEL_INT_PHY_MODE)) {
+ if (hw->mac.type == ixgbe_mac_X550EM_x &&
+ !(hw->phy.nw_mng_if_sel & IXGBE_NW_MNG_IF_SEL_INT_PHY_MODE)) {
/* If link is down, there is no setup necessary so return */
status = ixgbe_ext_phy_t_x550em_get_link(hw, &link_up);
if (status != IXGBE_SUCCESS)
/* Disable AN and force speed to 10G Serial. */
status = hw->mac.ops.read_iosf_sb_reg(hw,
- IXGBE_KRM_LINK_CTRL_1(hw->bus.lan_id),
- IXGBE_SB_IOSF_TARGET_KR_PHY, ®_val);
+ IXGBE_KRM_LINK_CTRL_1(hw->bus.lan_id),
+ IXGBE_SB_IOSF_TARGET_KR_PHY, ®_val);
if (status != IXGBE_SUCCESS)
return status;
reg_val &= ~IXGBE_KRM_LINK_CTRL_1_TETH_AN_ENABLE;
reg_val &= ~IXGBE_KRM_LINK_CTRL_1_TETH_FORCE_SPEED_MASK;
reg_val |= IXGBE_KRM_LINK_CTRL_1_TETH_FORCE_SPEED_10G;
status = hw->mac.ops.write_iosf_sb_reg(hw,
- IXGBE_KRM_LINK_CTRL_1(hw->bus.lan_id),
- IXGBE_SB_IOSF_TARGET_KR_PHY, reg_val);
+ IXGBE_KRM_LINK_CTRL_1(hw->bus.lan_id),
+ IXGBE_SB_IOSF_TARGET_KR_PHY, reg_val);
if (status != IXGBE_SUCCESS)
return status;
/* Set near-end loopback clocks. */
status = hw->mac.ops.read_iosf_sb_reg(hw,
- IXGBE_KRM_PORT_CAR_GEN_CTRL(hw->bus.lan_id),
- IXGBE_SB_IOSF_TARGET_KR_PHY, ®_val);
+ IXGBE_KRM_PORT_CAR_GEN_CTRL(hw->bus.lan_id),
+ IXGBE_SB_IOSF_TARGET_KR_PHY, ®_val);
if (status != IXGBE_SUCCESS)
return status;
reg_val |= IXGBE_KRM_PORT_CAR_GEN_CTRL_NELB_32B;
reg_val |= IXGBE_KRM_PORT_CAR_GEN_CTRL_NELB_KRPCS;
status = hw->mac.ops.write_iosf_sb_reg(hw,
- IXGBE_KRM_PORT_CAR_GEN_CTRL(hw->bus.lan_id),
- IXGBE_SB_IOSF_TARGET_KR_PHY, reg_val);
+ IXGBE_KRM_PORT_CAR_GEN_CTRL(hw->bus.lan_id),
+ IXGBE_SB_IOSF_TARGET_KR_PHY, reg_val);
if (status != IXGBE_SUCCESS)
return status;
/* Set loopback enable. */
status = hw->mac.ops.read_iosf_sb_reg(hw,
- IXGBE_KRM_PMD_DFX_BURNIN(hw->bus.lan_id),
- IXGBE_SB_IOSF_TARGET_KR_PHY, ®_val);
+ IXGBE_KRM_PMD_DFX_BURNIN(hw->bus.lan_id),
+ IXGBE_SB_IOSF_TARGET_KR_PHY, ®_val);
if (status != IXGBE_SUCCESS)
return status;
reg_val |= IXGBE_KRM_PMD_DFX_BURNIN_TX_RX_KR_LB_MASK;
status = hw->mac.ops.write_iosf_sb_reg(hw,
- IXGBE_KRM_PMD_DFX_BURNIN(hw->bus.lan_id),
- IXGBE_SB_IOSF_TARGET_KR_PHY, reg_val);
+ IXGBE_KRM_PMD_DFX_BURNIN(hw->bus.lan_id),
+ IXGBE_SB_IOSF_TARGET_KR_PHY, reg_val);
if (status != IXGBE_SUCCESS)
return status;
/* Training bypass. */
status = hw->mac.ops.read_iosf_sb_reg(hw,
- IXGBE_KRM_RX_TRN_LINKUP_CTRL(hw->bus.lan_id),
- IXGBE_SB_IOSF_TARGET_KR_PHY, ®_val);
+ IXGBE_KRM_RX_TRN_LINKUP_CTRL(hw->bus.lan_id),
+ IXGBE_SB_IOSF_TARGET_KR_PHY, ®_val);
if (status != IXGBE_SUCCESS)
return status;
reg_val |= IXGBE_KRM_RX_TRN_LINKUP_CTRL_PROTOCOL_BYPASS;
status = hw->mac.ops.write_iosf_sb_reg(hw,
- IXGBE_KRM_RX_TRN_LINKUP_CTRL(hw->bus.lan_id),
- IXGBE_SB_IOSF_TARGET_KR_PHY, reg_val);
+ IXGBE_KRM_RX_TRN_LINKUP_CTRL(hw->bus.lan_id),
+ IXGBE_SB_IOSF_TARGET_KR_PHY, reg_val);
return status;
}
*
* Reads a 16 bit word from the EEPROM using the hostif.
**/
-s32 ixgbe_read_ee_hostif_data_X550(struct ixgbe_hw *hw, u16 offset,
- u16 *data)
+s32 ixgbe_read_ee_hostif_X550(struct ixgbe_hw *hw, u16 offset, u16 *data)
{
- s32 status;
+ const u32 mask = IXGBE_GSSR_SW_MNG_SM | IXGBE_GSSR_EEP_SM;
struct ixgbe_hic_read_shadow_ram buffer;
+ s32 status;
- DEBUGFUNC("ixgbe_read_ee_hostif_data_X550");
+ DEBUGFUNC("ixgbe_read_ee_hostif_X550");
buffer.hdr.req.cmd = FW_READ_SHADOW_RAM_CMD;
buffer.hdr.req.buf_lenh = 0;
buffer.hdr.req.buf_lenl = FW_READ_SHADOW_RAM_LEN;
/* one word */
buffer.length = IXGBE_CPU_TO_BE16(sizeof(u16));
- status = ixgbe_host_interface_command(hw, (u32 *)&buffer,
- sizeof(buffer),
- IXGBE_HI_COMMAND_TIMEOUT, false);
-
+ status = hw->mac.ops.acquire_swfw_sync(hw, mask);
if (status)
return status;
- *data = (u16)IXGBE_READ_REG_ARRAY(hw, IXGBE_FLEX_MNG,
- FW_NVM_DATA_OFFSET);
-
- return 0;
-}
-
-/**
- * ixgbe_read_ee_hostif_X550 - Read EEPROM word using a host interface command
- * @hw: pointer to hardware structure
- * @offset: offset of word in the EEPROM to read
- * @data: word read from the EEPROM
- *
- * Reads a 16 bit word from the EEPROM using the hostif.
- **/
-s32 ixgbe_read_ee_hostif_X550(struct ixgbe_hw *hw, u16 offset,
- u16 *data)
-{
- s32 status = IXGBE_SUCCESS;
-
- DEBUGFUNC("ixgbe_read_ee_hostif_X550");
-
- if (hw->mac.ops.acquire_swfw_sync(hw, IXGBE_GSSR_EEP_SM) ==
- IXGBE_SUCCESS) {
- status = ixgbe_read_ee_hostif_data_X550(hw, offset, data);
- hw->mac.ops.release_swfw_sync(hw, IXGBE_GSSR_EEP_SM);
- } else {
- status = IXGBE_ERR_SWFW_SYNC;
+ status = ixgbe_hic_unlocked(hw, (u32 *)&buffer, sizeof(buffer),
+ IXGBE_HI_COMMAND_TIMEOUT);
+ if (!status) {
+ *data = (u16)IXGBE_READ_REG_ARRAY(hw, IXGBE_FLEX_MNG,
+ FW_NVM_DATA_OFFSET);
}
+ hw->mac.ops.release_swfw_sync(hw, mask);
return status;
}
s32 ixgbe_read_ee_hostif_buffer_X550(struct ixgbe_hw *hw,
u16 offset, u16 words, u16 *data)
{
+ const u32 mask = IXGBE_GSSR_SW_MNG_SM | IXGBE_GSSR_EEP_SM;
struct ixgbe_hic_read_shadow_ram buffer;
u32 current_word = 0;
u16 words_to_read;
DEBUGFUNC("ixgbe_read_ee_hostif_buffer_X550");
/* Take semaphore for the entire operation. */
- status = hw->mac.ops.acquire_swfw_sync(hw, IXGBE_GSSR_EEP_SM);
+ status = hw->mac.ops.acquire_swfw_sync(hw, mask);
if (status) {
DEBUGOUT("EEPROM read buffer - semaphore failed\n");
return status;
}
+
while (words) {
if (words > FW_MAX_READ_BUFFER_SIZE / 2)
words_to_read = FW_MAX_READ_BUFFER_SIZE / 2;
buffer.address = IXGBE_CPU_TO_BE32((offset + current_word) * 2);
buffer.length = IXGBE_CPU_TO_BE16(words_to_read * 2);
- status = ixgbe_host_interface_command(hw, (u32 *)&buffer,
- sizeof(buffer),
- IXGBE_HI_COMMAND_TIMEOUT,
- false);
+ status = ixgbe_hic_unlocked(hw, (u32 *)&buffer, sizeof(buffer),
+ IXGBE_HI_COMMAND_TIMEOUT);
if (status) {
DEBUGOUT("Host interface command failed\n");
}
out:
- hw->mac.ops.release_swfw_sync(hw, IXGBE_GSSR_EEP_SM);
+ hw->mac.ops.release_swfw_sync(hw, mask);
return status;
}
if (ext_ability & IXGBE_MDIO_PHY_1000BASET_ABILITY)
physical_layer |= IXGBE_PHYSICAL_LAYER_1000BASE_T;
break;
+ case ixgbe_phy_fw:
+ if (hw->phy.speeds_supported & IXGBE_LINK_SPEED_1GB_FULL)
+ physical_layer |= IXGBE_PHYSICAL_LAYER_1000BASE_T;
+ if (hw->phy.speeds_supported & IXGBE_LINK_SPEED_100_FULL)
+ physical_layer |= IXGBE_PHYSICAL_LAYER_100BASE_TX;
+ if (hw->phy.speeds_supported & IXGBE_LINK_SPEED_10_FULL)
+ physical_layer |= IXGBE_PHYSICAL_LAYER_10BASE_T;
+ break;
default:
break;
}
case IXGBE_DEV_ID_X550EM_A_KR:
case IXGBE_DEV_ID_X550EM_A_KR_L:
ret_val = hw->mac.ops.read_iosf_sb_reg(hw,
- IXGBE_KRM_AN_CNTL_1(hw->bus.lan_id),
- IXGBE_SB_IOSF_TARGET_KR_PHY, ®_val);
+ IXGBE_KRM_AN_CNTL_1(hw->bus.lan_id),
+ IXGBE_SB_IOSF_TARGET_KR_PHY, ®_val);
if (ret_val != IXGBE_SUCCESS)
goto out;
reg_val &= ~(IXGBE_KRM_AN_CNTL_1_SYM_PAUSE |
- IXGBE_KRM_AN_CNTL_1_ASM_PAUSE);
+ IXGBE_KRM_AN_CNTL_1_ASM_PAUSE);
if (pause)
reg_val |= IXGBE_KRM_AN_CNTL_1_SYM_PAUSE;
if (asm_dir)
reg_val |= IXGBE_KRM_AN_CNTL_1_ASM_PAUSE;
ret_val = hw->mac.ops.write_iosf_sb_reg(hw,
- IXGBE_KRM_AN_CNTL_1(hw->bus.lan_id),
- IXGBE_SB_IOSF_TARGET_KR_PHY, reg_val);
+ IXGBE_KRM_AN_CNTL_1(hw->bus.lan_id),
+ IXGBE_SB_IOSF_TARGET_KR_PHY, reg_val);
/* This device does not fully support AN. */
hw->fc.disable_fc_autoneg = true;
*/
if (hw->fc.disable_fc_autoneg) {
ERROR_REPORT1(IXGBE_ERROR_UNSUPPORTED,
- "Flow control autoneg is disabled");
+ "Flow control autoneg is disabled");
goto out;
}
/* Check at auto-negotiation has completed */
status = hw->mac.ops.read_iosf_sb_reg(hw,
- IXGBE_KRM_LINK_S1(hw->bus.lan_id),
- IXGBE_SB_IOSF_TARGET_KR_PHY, &link_s1);
+ IXGBE_KRM_LINK_S1(hw->bus.lan_id),
+ IXGBE_SB_IOSF_TARGET_KR_PHY, &link_s1);
if (status != IXGBE_SUCCESS ||
(link_s1 & IXGBE_KRM_LINK_S1_MAC_AN_COMPLETE) == 0) {
* local flow control settings accordingly
*/
status = hw->mac.ops.read_iosf_sb_reg(hw,
- IXGBE_KRM_AN_CNTL_1(hw->bus.lan_id),
- IXGBE_SB_IOSF_TARGET_KR_PHY, &an_cntl_1);
+ IXGBE_KRM_AN_CNTL_1(hw->bus.lan_id),
+ IXGBE_SB_IOSF_TARGET_KR_PHY, &an_cntl_1);
if (status != IXGBE_SUCCESS) {
DEBUGOUT("Auto-Negotiation did not complete\n");
}
status = hw->mac.ops.read_iosf_sb_reg(hw,
- IXGBE_KRM_LP_BASE_PAGE_HIGH(hw->bus.lan_id),
- IXGBE_SB_IOSF_TARGET_KR_PHY, &lp_an_page_low);
+ IXGBE_KRM_LP_BASE_PAGE_HIGH(hw->bus.lan_id),
+ IXGBE_SB_IOSF_TARGET_KR_PHY, &lp_an_page_low);
if (status != IXGBE_SUCCESS) {
DEBUGOUT("Auto-Negotiation did not complete\n");
}
/**
- * ixgbe_fc_autoneg_fiber_x550em_a - Enable flow control IEEE clause 37
+ * ixgbe_fc_autoneg_fiber_x550em_a - passthrough FC settings
* @hw: pointer to hardware structure
*
- * Enable flow control according to IEEE clause 37.
**/
void ixgbe_fc_autoneg_fiber_x550em_a(struct ixgbe_hw *hw)
{
- u32 link_s1, pcs_an_lp, pcs_an;
- s32 status = IXGBE_ERR_FC_NOT_NEGOTIATED;
- ixgbe_link_speed speed;
- bool link_up;
-
- /* AN should have completed when the cable was plugged in.
- * Look for reasons to bail out. Bail out if:
- * - FC autoneg is disabled, or if
- * - link is not up.
- */
- if (hw->fc.disable_fc_autoneg) {
- ERROR_REPORT1(IXGBE_ERROR_UNSUPPORTED,
- "Flow control autoneg is disabled");
- goto out;
- }
-
- hw->mac.ops.check_link(hw, &speed, &link_up, false);
- if (!link_up) {
- ERROR_REPORT1(IXGBE_ERROR_SOFTWARE, "The link is down");
- goto out;
- }
-
- /* Check if auto-negotiation has completed */
- status = hw->mac.ops.read_iosf_sb_reg(hw,
- IXGBE_KRM_LINK_S1(hw->bus.lan_id),
- IXGBE_SB_IOSF_TARGET_KR_PHY, &link_s1);
-
- if (status != IXGBE_SUCCESS ||
- (link_s1 & IXGBE_KRM_LINK_S1_MAC_AN_COMPLETE) == 0) {
- DEBUGOUT("Auto-Negotiation did not complete\n");
- status = IXGBE_ERR_FC_NOT_NEGOTIATED;
- goto out;
- }
-
- /* Determine advertised flow control */
- status = hw->mac.ops.read_iosf_sb_reg(hw,
- IXGBE_KRM_PCS_KX_AN(hw->bus.lan_id),
- IXGBE_SB_IOSF_TARGET_KR_PHY, &pcs_an);
-
- if (status != IXGBE_SUCCESS) {
- DEBUGOUT("Auto-Negotiation did not complete\n");
- goto out;
- }
-
- /* Determine link parter flow control */
- status = hw->mac.ops.read_iosf_sb_reg(hw,
- IXGBE_KRM_PCS_KX_AN_LP(hw->bus.lan_id),
- IXGBE_SB_IOSF_TARGET_KR_PHY, &pcs_an_lp);
-
- if (status != IXGBE_SUCCESS) {
- DEBUGOUT("Auto-Negotiation did not complete\n");
- goto out;
- }
-
- status = ixgbe_negotiate_fc(hw, pcs_an, pcs_an_lp,
- IXGBE_KRM_PCS_KX_AN_SYM_PAUSE,
- IXGBE_KRM_PCS_KX_AN_ASM_PAUSE,
- IXGBE_KRM_PCS_KX_AN_LP_SYM_PAUSE,
- IXGBE_KRM_PCS_KX_AN_LP_ASM_PAUSE);
-
-out:
- if (status == IXGBE_SUCCESS) {
- hw->fc.fc_was_autonegged = true;
- } else {
- hw->fc.fc_was_autonegged = false;
- hw->fc.current_mode = hw->fc.requested_mode;
- }
+ hw->fc.fc_was_autonegged = false;
+ hw->fc.current_mode = hw->fc.requested_mode;
}
/**
void ixgbe_fc_autoneg_sgmii_x550em_a(struct ixgbe_hw *hw)
{
s32 status = IXGBE_ERR_FC_NOT_NEGOTIATED;
- u16 reg, pcs_an_lp, pcs_an;
+ u32 info[FW_PHY_ACT_DATA_COUNT] = { 0 };
ixgbe_link_speed speed;
bool link_up;
+ u32 fc;
/* AN should have completed when the cable was plugged in.
* Look for reasons to bail out. Bail out if:
}
/* Check if auto-negotiation has completed */
- status = hw->phy.ops.read_reg(hw, IXGBE_M88E1500_COPPER_STATUS,
- IXGBE_MDIO_ZERO_DEV_TYPE, ®);
+ status = ixgbe_fw_phy_activity(hw, FW_PHY_ACT_GET_LINK_INFO, &info);
if (status != IXGBE_SUCCESS ||
- (reg & IXGBE_M88E1500_COPPER_STATUS_AN_DONE) == 0) {
+ !(info[0] & FW_PHY_ACT_GET_LINK_INFO_AN_COMPLETE)) {
DEBUGOUT("Auto-Negotiation did not complete\n");
status = IXGBE_ERR_FC_NOT_NEGOTIATED;
goto out;
}
- /* Get the advertized flow control */
- status = hw->phy.ops.read_reg(hw, IXGBE_M88E1500_COPPER_AN,
- IXGBE_MDIO_ZERO_DEV_TYPE, &pcs_an);
- if (status != IXGBE_SUCCESS)
- goto out;
+ /* Get the advertized flow control and modify it to indicate
+ * pause and asymmetric pause instead of rx and tx
+ */
+ fc = info[0];
+ if (fc & FW_PHY_ACT_GET_LINK_INFO_FC_RX)
+ fc ^= FW_PHY_ACT_GET_LINK_INFO_FC_TX;
- /* Get link partner's flow control */
- status = hw->phy.ops.read_reg(hw,
- IXGBE_M88E1500_COPPER_AN_LP_ABILITY,
- IXGBE_MDIO_ZERO_DEV_TYPE, &pcs_an_lp);
- if (status != IXGBE_SUCCESS)
- goto out;
+ /* Modify link partner's flow control to indicate pause and
+ * asymmetric pause instead of rx and tx
+ */
+ if (fc & FW_PHY_ACT_GET_LINK_INFO_LP_FC_RX)
+ fc ^= FW_PHY_ACT_GET_LINK_INFO_LP_FC_TX;
/* Negotiate the flow control */
- status = ixgbe_negotiate_fc(hw, (u32)pcs_an, (u32)pcs_an_lp,
- IXGBE_M88E1500_COPPER_AN_PAUSE,
- IXGBE_M88E1500_COPPER_AN_AS_PAUSE,
- IXGBE_M88E1500_COPPER_AN_LP_PAUSE,
- IXGBE_M88E1500_COPPER_AN_LP_AS_PAUSE);
+ status = ixgbe_negotiate_fc(hw, fc, fc,
+ FW_PHY_ACT_GET_LINK_INFO_FC_RX,
+ FW_PHY_ACT_GET_LINK_INFO_FC_TX,
+ FW_PHY_ACT_GET_LINK_INFO_LP_FC_RX,
+ FW_PHY_ACT_GET_LINK_INFO_LP_FC_TX);
out:
if (status == IXGBE_SUCCESS) {
}
}
-/**
- * ixgbe_setup_fc_sgmii_x550em_a - Set up flow control
- * @hw: pointer to hardware structure
- *
- * Called at init time to set up flow control.
- **/
-s32 ixgbe_setup_fc_sgmii_x550em_a(struct ixgbe_hw *hw)
-{
- u16 reg;
- s32 rc;
-
- /* Validate the requested mode */
- if (hw->fc.strict_ieee && hw->fc.requested_mode == ixgbe_fc_rx_pause) {
- ERROR_REPORT1(IXGBE_ERROR_UNSUPPORTED,
- "ixgbe_fc_rx_pause not valid in strict IEEE mode\n");
- return IXGBE_ERR_INVALID_LINK_SETTINGS;
- }
-
- if (hw->fc.requested_mode == ixgbe_fc_default)
- hw->fc.requested_mode = ixgbe_fc_full;
-
- /* Read contents of the Auto-Negotiation register, page 0 reg 4 */
- rc = hw->phy.ops.read_reg(hw, IXGBE_M88E1500_COPPER_AN,
- IXGBE_MDIO_ZERO_DEV_TYPE, ®);
- if (rc)
- goto out;
-
- /* Disable all the settings related to Flow control Auto-negotiation */
- reg &= ~IXGBE_M88E1500_COPPER_AN_AS_PAUSE;
- reg &= ~IXGBE_M88E1500_COPPER_AN_PAUSE;
-
- /* Configure the Asymmetric and symmetric pause according to the user
- * requested mode.
- */
- switch (hw->fc.requested_mode) {
- case ixgbe_fc_full:
- reg |= IXGBE_M88E1500_COPPER_AN_PAUSE;
- reg |= IXGBE_M88E1500_COPPER_AN_AS_PAUSE;
- break;
- case ixgbe_fc_rx_pause:
- reg |= IXGBE_M88E1500_COPPER_AN_PAUSE;
- reg |= IXGBE_M88E1500_COPPER_AN_AS_PAUSE;
- break;
- case ixgbe_fc_tx_pause:
- reg |= IXGBE_M88E1500_COPPER_AN_AS_PAUSE;
- break;
- default:
- break;
- }
-
- /* Write back to the Auto-Negotiation register with newly configured
- * fields
- */
- hw->phy.ops.write_reg(hw, IXGBE_M88E1500_COPPER_AN,
- IXGBE_MDIO_ZERO_DEV_TYPE, reg);
-
- /* In this section of the code we restart Auto-negotiation */
-
- /* Read the CONTROL register, Page 0 reg 0 */
- rc = hw->phy.ops.read_reg(hw, IXGBE_M88E1500_COPPER_CTRL,
- IXGBE_MDIO_ZERO_DEV_TYPE, ®);
- if (rc)
- goto out;
-
- /* Set the bit to restart Auto-Neg. The bit to enable Auto-neg is ON
- * by default
- */
- reg |= IXGBE_M88E1500_COPPER_CTRL_RESTART_AN;
-
- /* write the new values to the register to restart Auto-Negotiation */
- hw->phy.ops.write_reg(hw, IXGBE_M88E1500_COPPER_CTRL,
- IXGBE_MDIO_ZERO_DEV_TYPE, reg);
-
-out:
- return rc;
-}
-
/**
* ixgbe_setup_fc_backplane_x550em_a - Set up flow control
* @hw: pointer to hardware structure
/* Validate the requested mode */
if (hw->fc.strict_ieee && hw->fc.requested_mode == ixgbe_fc_rx_pause) {
ERROR_REPORT1(IXGBE_ERROR_UNSUPPORTED,
- "ixgbe_fc_rx_pause not valid in strict IEEE mode\n");
+ "ixgbe_fc_rx_pause not valid in strict IEEE mode\n");
return IXGBE_ERR_INVALID_LINK_SETTINGS;
}
* we link at 10G, the 1G advertisement is harmless and vice versa.
*/
status = hw->mac.ops.read_iosf_sb_reg(hw,
- IXGBE_KRM_AN_CNTL_1(hw->bus.lan_id),
- IXGBE_SB_IOSF_TARGET_KR_PHY, &an_cntl);
+ IXGBE_KRM_AN_CNTL_1(hw->bus.lan_id),
+ IXGBE_SB_IOSF_TARGET_KR_PHY, &an_cntl);
if (status != IXGBE_SUCCESS) {
DEBUGOUT("Auto-Negotiation did not complete\n");
case ixgbe_fc_full:
/* Flow control (both Rx and Tx) is enabled by SW override. */
an_cntl |= IXGBE_KRM_AN_CNTL_1_SYM_PAUSE |
- IXGBE_KRM_AN_CNTL_1_ASM_PAUSE;
+ IXGBE_KRM_AN_CNTL_1_ASM_PAUSE;
break;
default:
ERROR_REPORT1(IXGBE_ERROR_ARGUMENT,
}
status = hw->mac.ops.write_iosf_sb_reg(hw,
- IXGBE_KRM_AN_CNTL_1(hw->bus.lan_id),
- IXGBE_SB_IOSF_TARGET_KR_PHY, an_cntl);
+ IXGBE_KRM_AN_CNTL_1(hw->bus.lan_id),
+ IXGBE_SB_IOSF_TARGET_KR_PHY, an_cntl);
/* Restart auto-negotiation. */
status = ixgbe_restart_an_internal_phy_x550em(hw);
return status;
}
-/**
- * ixgbe_setup_fc_fiber_x550em_a - Set up flow control
- * @hw: pointer to hardware structure
- *
- * Called at init time to set up flow control.
- **/
-s32 ixgbe_setup_fc_fiber_x550em_a(struct ixgbe_hw *hw)
-{
- struct ixgbe_mac_info *mac = &hw->mac;
- s32 rc = IXGBE_SUCCESS;
- u32 an_cntl4, lctrl, pcs_an;
-
- DEBUGFUNC("ixgbe_setup_fc_fiber_x550em_a");
-
- /* Validate the requested mode */
- if (hw->fc.strict_ieee && hw->fc.requested_mode == ixgbe_fc_rx_pause) {
- ERROR_REPORT1(IXGBE_ERROR_UNSUPPORTED,
- "ixgbe_fc_rx_pause not valid in strict IEEE mode\n");
- return IXGBE_ERR_INVALID_LINK_SETTINGS;
- }
-
- /* Enable clause 37 auto-negotiation in KRM_LINK_CTRL_1 */
- if (hw->fc.requested_mode == ixgbe_fc_default)
- hw->fc.requested_mode = ixgbe_fc_full;
-
- rc = mac->ops.read_iosf_sb_reg(hw,
- IXGBE_KRM_LINK_CTRL_1(hw->bus.lan_id),
- IXGBE_SB_IOSF_TARGET_KR_PHY, &lctrl);
- if (rc)
- return rc;
-
- lctrl |= IXGBE_KRM_LINK_CTRL_1_TETH_AN_ENABLE;
- lctrl |= IXGBE_KRM_LINK_CTRL_1_TETH_AN_CLAUSE_37_EN;
-
- rc = mac->ops.write_iosf_sb_reg(hw,
- IXGBE_KRM_LINK_CTRL_1(hw->bus.lan_id),
- IXGBE_SB_IOSF_TARGET_KR_PHY, lctrl);
- if (rc)
- return rc;
-
- /* Enable clause 37 over 73 in KRM_AN_CNTL_4 */
- rc = mac->ops.read_iosf_sb_reg(hw,
- IXGBE_KRM_AN_CNTL_4(hw->bus.lan_id),
- IXGBE_SB_IOSF_TARGET_KR_PHY, &an_cntl4);
- if (rc)
- return rc;
-
- an_cntl4 |= IXGBE_KRM_AN_CNTL_4_ECSR_AN37_OVER_73;
-
- rc = mac->ops.write_iosf_sb_reg(hw,
- IXGBE_KRM_AN_CNTL_4(hw->bus.lan_id),
- IXGBE_SB_IOSF_TARGET_KR_PHY, an_cntl4);
- if (rc)
- return rc;
-
- rc = hw->mac.ops.read_iosf_sb_reg(hw,
- IXGBE_KRM_PCS_KX_AN(hw->bus.lan_id),
- IXGBE_SB_IOSF_TARGET_KR_PHY, &pcs_an);
-
- if (rc)
- return rc;
-
- /* The possible values of fc.requested_mode are:
- * 0: Flow control is completely disabled
- * 1: Rx flow control is enabled (we can receive pause frames,
- * but not send pause frames).
- * 2: Tx flow control is enabled (we can send pause frames but
- * we do not support receiving pause frames).
- * 3: Both Rx and Tx flow control (symmetric) are enabled.
- * other: Invalid.
- */
- switch (hw->fc.requested_mode) {
- case ixgbe_fc_none:
- /* Flow control completely disabled by software override. */
- pcs_an &= ~(IXGBE_KRM_AN_CNTL_1_SYM_PAUSE |
- IXGBE_KRM_AN_CNTL_1_ASM_PAUSE);
- break;
- case ixgbe_fc_tx_pause:
- /* Tx Flow control is enabled, and Rx Flow control is
- * disabled by software override.
- */
- pcs_an |= IXGBE_KRM_PCS_KX_AN_ASM_PAUSE;
- pcs_an &= ~IXGBE_KRM_PCS_KX_AN_SYM_PAUSE;
- break;
- case ixgbe_fc_rx_pause:
- /* Rx Flow control is enabled and Tx Flow control is
- * disabled by software override. Since there really
- * isn't a way to advertise that we are capable of RX
- * Pause ONLY, we will advertise that we support both
- * symmetric and asymmetric Rx PAUSE, as such we fall
- * through to the fc_full statement. Later, we will
- * disable the adapter's ability to send PAUSE frames.
- */
- case ixgbe_fc_full:
- /* Flow control (both Rx and Tx) is enabled by SW override. */
- pcs_an |= IXGBE_KRM_PCS_KX_AN_SYM_PAUSE |
- IXGBE_KRM_PCS_KX_AN_ASM_PAUSE;
- break;
- default:
- ERROR_REPORT1(IXGBE_ERROR_ARGUMENT,
- "Flow control param set incorrectly\n");
- return IXGBE_ERR_CONFIG;
- }
-
- rc = hw->mac.ops.write_iosf_sb_reg(hw,
- IXGBE_KRM_PCS_KX_AN(hw->bus.lan_id),
- IXGBE_SB_IOSF_TARGET_KR_PHY, pcs_an);
-
- /* Restart auto-negotiation. */
- rc = ixgbe_restart_an_internal_phy_x550em(hw);
-
- return rc;
-}
-
/**
* ixgbe_set_mux - Set mux for port 1 access with CS4227
* @hw: pointer to hardware structure
* instances.
**/
s32 ixgbe_read_phy_reg_x550a(struct ixgbe_hw *hw, u32 reg_addr,
- u32 device_type, u16 *phy_data)
+ u32 device_type, u16 *phy_data)
{
s32 status;
u32 mask = hw->phy.phy_semaphore_mask | IXGBE_GSSR_TOKEN_SM;
* The PHY Token is needed since the MDIO is shared between to MAC instances.
**/
s32 ixgbe_write_phy_reg_x550a(struct ixgbe_hw *hw, u32 reg_addr,
- u32 device_type, u16 phy_data)
+ u32 device_type, u16 phy_data)
{
s32 status;
u32 mask = hw->phy.phy_semaphore_mask | IXGBE_GSSR_TOKEN_SM;
else
force_speed = IXGBE_LINK_SPEED_1GB_FULL;
- /* If internal link mode is XFI, then setup XFI internal link. */
- if (!(hw->phy.nw_mng_if_sel & IXGBE_NW_MNG_IF_SEL_INT_PHY_MODE)) {
+ /* If X552 and internal link mode is XFI, then setup XFI internal link.
+ */
+ if (hw->mac.type == ixgbe_mac_X550EM_x &&
+ !(hw->phy.nw_mng_if_sel & IXGBE_NW_MNG_IF_SEL_INT_PHY_MODE)) {
status = ixgbe_setup_ixfi_x550em(hw, &force_speed);
if (status != IXGBE_SUCCESS)
bool *link_up, bool link_up_wait_to_complete)
{
u32 status;
- u16 autoneg_status;
+ u16 i, autoneg_status = 0;
if (hw->mac.ops.get_media_type(hw) != ixgbe_media_type_copper)
return IXGBE_ERR_CONFIG;
return status;
/* MAC link is up, so check external PHY link.
- * Read this twice back to back to indicate current status.
+ * X557 PHY. Link status is latching low, and can only be used to detect
+ * link drop, and not the current status of the link without performing
+ * back-to-back reads.
*/
- status = hw->phy.ops.read_reg(hw, IXGBE_MDIO_AUTO_NEG_STATUS,
- IXGBE_MDIO_AUTO_NEG_DEV_TYPE,
- &autoneg_status);
-
- if (status != IXGBE_SUCCESS)
- return status;
-
- status = hw->phy.ops.read_reg(hw, IXGBE_MDIO_AUTO_NEG_STATUS,
- IXGBE_MDIO_AUTO_NEG_DEV_TYPE,
- &autoneg_status);
+ for (i = 0; i < 2; i++) {
+ status = hw->phy.ops.read_reg(hw, IXGBE_MDIO_AUTO_NEG_STATUS,
+ IXGBE_MDIO_AUTO_NEG_DEV_TYPE,
+ &autoneg_status);
- if (status != IXGBE_SUCCESS)
- return status;
+ if (status != IXGBE_SUCCESS)
+ return status;
+ }
/* If external PHY link is not up, then indicate link not up */
if (!(autoneg_status & IXGBE_MDIO_AUTO_NEG_LINK_STATUS))
return IXGBE_SUCCESS;
}
+/**
+ * ixgbe_set_fw_drv_ver_x550 - Sends driver version to firmware
+ * @hw: pointer to the HW structure
+ * @maj: driver version major number
+ * @min: driver version minor number
+ * @build: driver version build number
+ * @sub: driver version sub build number
+ * @len: length of driver_ver string
+ * @driver_ver: driver string
+ *
+ * Sends driver version number to firmware through the manageability
+ * block. On success return IXGBE_SUCCESS
+ * else returns IXGBE_ERR_SWFW_SYNC when encountering an error acquiring
+ * semaphore or IXGBE_ERR_HOST_INTERFACE_COMMAND when command fails.
+ **/
+s32 ixgbe_set_fw_drv_ver_x550(struct ixgbe_hw *hw, u8 maj, u8 min,
+ u8 build, u8 sub, u16 len, const char *driver_ver)
+{
+ struct ixgbe_hic_drv_info2 fw_cmd;
+ s32 ret_val = IXGBE_SUCCESS;
+ int i;
+
+ DEBUGFUNC("ixgbe_set_fw_drv_ver_x550");
+
+ if ((len == 0) || (driver_ver == NULL) ||
+ (len > sizeof(fw_cmd.driver_string)))
+ return IXGBE_ERR_INVALID_ARGUMENT;
+
+ fw_cmd.hdr.cmd = FW_CEM_CMD_DRIVER_INFO;
+ fw_cmd.hdr.buf_len = FW_CEM_CMD_DRIVER_INFO_LEN + len;
+ fw_cmd.hdr.cmd_or_resp.cmd_resv = FW_CEM_CMD_RESERVED;
+ fw_cmd.port_num = (u8)hw->bus.func;
+ fw_cmd.ver_maj = maj;
+ fw_cmd.ver_min = min;
+ fw_cmd.ver_build = build;
+ fw_cmd.ver_sub = sub;
+ fw_cmd.hdr.checksum = 0;
+ memcpy(fw_cmd.driver_string, driver_ver, len);
+ fw_cmd.hdr.checksum = ixgbe_calculate_checksum((u8 *)&fw_cmd,
+ (FW_CEM_HDR_LEN + fw_cmd.hdr.buf_len));
+
+ for (i = 0; i <= FW_CEM_MAX_RETRIES; i++) {
+ ret_val = ixgbe_host_interface_command(hw, (u32 *)&fw_cmd,
+ sizeof(fw_cmd),
+ IXGBE_HI_COMMAND_TIMEOUT,
+ true);
+ if (ret_val != IXGBE_SUCCESS)
+ continue;
+
+ if (fw_cmd.hdr.cmd_or_resp.ret_status ==
+ FW_CEM_RESP_STATUS_SUCCESS)
+ ret_val = IXGBE_SUCCESS;
+ else
+ ret_val = IXGBE_ERR_HOST_INTERFACE_COMMAND;
+
+ break;
+ }
+
+ return ret_val;
+}
git.droids-corp.org / dpdk.git / blobdiff