ixgbe: fix X550 copper link

[dpdk.git] / drivers / net / ixgbe / ixgbe_ethdev.c

diff --git a/drivers/net/ixgbe/ixgbe_ethdev.c b/drivers/net/ixgbe/ixgbe_ethdev.c
index d39640b..f18550c 100644 (file)
--- a/drivers/net/ixgbe/ixgbe_ethdev.c
+++ b/drivers/net/ixgbe/ixgbe_ethdev.c
@@ -1522,8 +1522,13 @@ ixgbe_dev_start(struct rte_eth_dev *dev)
                        goto error;
        }
 
-       /* Turn on the laser */
-       ixgbe_enable_tx_laser(hw);
+       if (hw->mac.ops.get_media_type(hw) == ixgbe_media_type_copper) {
+               /* Turn on the copper */
+               ixgbe_set_phy_power(hw, true);
+       } else {
+               /* Turn on the laser */
+               ixgbe_enable_tx_laser(hw);
+       }
 
        err = ixgbe_check_link(hw, &speed, &link_up, 0);
        if (err)
@@ -1643,8 +1648,13 @@ ixgbe_dev_stop(struct rte_eth_dev *dev)
                     vf < dev->pci_dev->max_vfs; vf++)
                vfinfo[vf].clear_to_send = false;
 
-       /* Turn off the laser */
-       ixgbe_disable_tx_laser(hw);
+       if (hw->mac.ops.get_media_type(hw) == ixgbe_media_type_copper) {
+               /* Turn off the copper */
+               ixgbe_set_phy_power(hw, false);
+       } else {
+               /* Turn off the laser */
+               ixgbe_disable_tx_laser(hw);
+       }
 
        ixgbe_dev_clear_queues(dev);
 
@@ -1670,7 +1680,7 @@ ixgbe_dev_stop(struct rte_eth_dev *dev)
 }
 
 /*
- * Set device link up: enable tx laser.
+ * Set device link up: enable tx.
  */
 static int
 ixgbe_dev_set_link_up(struct rte_eth_dev *dev)
@@ -1686,18 +1696,21 @@ ixgbe_dev_set_link_up(struct rte_eth_dev *dev)
                        return -ENOTSUP;
                }
 #endif
+       }
+
+       if (hw->mac.ops.get_media_type(hw) == ixgbe_media_type_copper) {
+               /* Turn on the copper */
+               ixgbe_set_phy_power(hw, true);
+       } else {
                /* Turn on the laser */
                ixgbe_enable_tx_laser(hw);
-               return 0;
        }
 
-       PMD_INIT_LOG(ERR, "Set link up is not supported by device id 0x%x",
-                    hw->device_id);
-       return -ENOTSUP;
+       return 0;
 }
 
 /*
- * Set device link down: disable tx laser.
+ * Set device link down: disable tx.
  */
 static int
 ixgbe_dev_set_link_down(struct rte_eth_dev *dev)
@@ -1713,14 +1726,17 @@ ixgbe_dev_set_link_down(struct rte_eth_dev *dev)
                        return -ENOTSUP;
                }
 #endif
+       }
+
+       if (hw->mac.ops.get_media_type(hw) == ixgbe_media_type_copper) {
+               /* Turn off the copper */
+               ixgbe_set_phy_power(hw, false);
+       } else {
                /* Turn off the laser */
                ixgbe_disable_tx_laser(hw);
-               return 0;
        }
 
-       PMD_INIT_LOG(ERR, "Set link down is not supported by device id 0x%x",
-                    hw->device_id);
-       return -ENOTSUP;
+       return 0;
 }
 
 /*