#include <rte_memory.h>
#include <rte_memcpy.h>
#include <rte_memzone.h>
-#include <rte_tailq.h>
#include <rte_eal.h>
#include <rte_per_lcore.h>
#include <rte_launch.h>
#include <rte_debug.h>
#include <rte_ether.h>
#include <rte_ethdev.h>
-#include <rte_ring.h>
#include <rte_mempool.h>
#include <rte_mbuf.h>
#include <rte_lpm.h>
#include <rte_ip_frag.h>
-#include "main.h"
-
#define RTE_LOGTYPE_IP_FRAG RTE_LOGTYPE_USER1
-#define MBUF_SIZE (2048 + sizeof(struct rte_mbuf) + RTE_PKTMBUF_HEADROOM)
-
/* allow max jumbo frame 9.5 KB */
#define JUMBO_FRAME_MAX_SIZE 0x2600
#define NB_MBUF 8192
-/*
- * RX and TX Prefetch, Host, and Write-back threshold values should be
- * carefully set for optimal performance. Consult the network
- * controller's datasheet and supporting DPDK documentation for guidance
- * on how these parameters should be set.
- */
-#define RX_PTHRESH 8 /**< Default values of RX prefetch threshold reg. */
-#define RX_HTHRESH 8 /**< Default values of RX host threshold reg. */
-#define RX_WTHRESH 4 /**< Default values of RX write-back threshold reg. */
-
-/*
- * These default values are optimized for use with the Intel(R) 82599 10 GbE
- * Controller and the DPDK ixgbe PMD. Consider using other values for other
- * network controllers and/or network drivers.
- */
-#define TX_PTHRESH 36 /**< Default values of TX prefetch threshold reg. */
-#define TX_HTHRESH 0 /**< Default values of TX host threshold reg. */
-#define TX_WTHRESH 0 /**< Default values of TX write-back threshold reg. */
-
#define MAX_PKT_BURST 32
#define BURST_TX_DRAIN_US 100 /* TX drain every ~100us */
} __rte_cache_aligned;
struct lcore_queue_conf lcore_queue_conf[RTE_MAX_LCORE];
-static const struct rte_eth_conf port_conf = {
+static struct rte_eth_conf port_conf = {
.rxmode = {
.max_rx_pkt_len = JUMBO_FRAME_MAX_SIZE,
.split_hdr_size = 0,
.hw_ip_checksum = 1, /**< IP checksum offload enabled */
.hw_vlan_filter = 0, /**< VLAN filtering disabled */
.jumbo_frame = 1, /**< Jumbo Frame Support enabled */
- .hw_strip_crc = 0, /**< CRC stripped by hardware */
+ .hw_strip_crc = 1, /**< CRC stripped by hardware */
},
.txmode = {
.mq_mode = ETH_MQ_TX_NONE,
},
};
-static const struct rte_eth_rxconf rx_conf = {
- .rx_thresh = {
- .pthresh = RX_PTHRESH,
- .hthresh = RX_HTHRESH,
- .wthresh = RX_WTHRESH,
- },
-};
-
-static const struct rte_eth_txconf tx_conf = {
- .tx_thresh = {
- .pthresh = TX_PTHRESH,
- .hthresh = TX_HTHRESH,
- .wthresh = TX_WTHRESH,
- },
- .tx_free_thresh = 0, /* Use PMD default values */
- .tx_rs_thresh = 0, /* Use PMD default values */
-};
-
/*
* IPv4 forwarding table
*/
uint8_t queueid, uint8_t port_in)
{
struct rx_queue *rxq;
- uint32_t i, len;
- uint8_t next_hop, port_out, ipv6;
+ uint32_t i, len, next_hop;
+ uint8_t port_out, ipv6;
int32_t len2;
ipv6 = 0;
len = qconf->tx_mbufs[port_out].len;
/* if this is an IPv4 packet */
- if (m->ol_flags & PKT_RX_IPV4_HDR) {
+ if (RTE_ETH_IS_IPV4_HDR(m->packet_type)) {
struct ipv4_hdr *ip_hdr;
uint32_t ip_dst;
/* Read the lookup key (i.e. ip_dst) from the input packet */
}
/* if we don't need to do any fragmentation */
- if (likely (IPV4_MTU_DEFAULT >= m->pkt.pkt_len)) {
+ if (likely (IPV4_MTU_DEFAULT >= m->pkt_len)) {
qconf->tx_mbufs[port_out].m_table[len] = m;
len2 = 1;
} else {
if (unlikely (len2 < 0))
return;
}
- }
- /* if this is an IPv6 packet */
- else if (m->ol_flags & PKT_RX_IPV6_HDR) {
+ } else if (RTE_ETH_IS_IPV6_HDR(m->packet_type)) {
+ /* if this is an IPv6 packet */
struct ipv6_hdr *ip_hdr;
ipv6 = 1;
ip_hdr = rte_pktmbuf_mtod(m, struct ipv6_hdr *);
/* Find destination port */
- if (rte_lpm6_lookup(rxq->lpm6, ip_hdr->dst_addr, &next_hop) == 0 &&
+ if (rte_lpm6_lookup(rxq->lpm6, ip_hdr->dst_addr,
+ &next_hop) == 0 &&
(enabled_port_mask & 1 << next_hop) != 0) {
port_out = next_hop;
}
/* if we don't need to do any fragmentation */
- if (likely (IPV6_MTU_DEFAULT >= m->pkt.pkt_len)) {
+ if (likely (IPV6_MTU_DEFAULT >= m->pkt_len)) {
qconf->tx_mbufs[port_out].m_table[len] = m;
len2 = 1;
} else {
rte_panic("No headroom in mbuf.\n");
}
- m->pkt.vlan_macip.f.l2_len = sizeof(struct ether_hdr);
+ m->l2_len = sizeof(struct ether_hdr);
/* 02:00:00:00:00:xx */
d_addr_bytes = ð_hdr->d_addr.addr_bytes[0];
argv[optind-1] = prgname;
ret = optind-1;
- optind = 0; /* reset getopt lib */
+ optind = 1; /* reset getopt lib */
return ret;
}
static void
print_ethaddr(const char *name, struct ether_addr *eth_addr)
{
- printf("%s%02X:%02X:%02X:%02X:%02X:%02X", name,
- eth_addr->addr_bytes[0],
- eth_addr->addr_bytes[1],
- eth_addr->addr_bytes[2],
- eth_addr->addr_bytes[3],
- eth_addr->addr_bytes[4],
- eth_addr->addr_bytes[5]);
+ char buf[ETHER_ADDR_FMT_SIZE];
+ ether_format_addr(buf, ETHER_ADDR_FMT_SIZE, eth_addr);
+ printf("%s%s", name, buf);
}
/* Check the link status of all ports in up to 9s, and print them finally */
continue;
}
/* clear all_ports_up flag if any link down */
- if (link.link_status == 0) {
+ if (link.link_status == ETH_LINK_DOWN) {
all_ports_up = 0;
break;
}
}
}
+/* Check L3 packet type detection capablity of the NIC port */
+static int
+check_ptype(int portid)
+{
+ int i, ret;
+ int ptype_l3_ipv4 = 0, ptype_l3_ipv6 = 0;
+ uint32_t ptype_mask = RTE_PTYPE_L3_MASK;
+
+ ret = rte_eth_dev_get_supported_ptypes(portid, ptype_mask, NULL, 0);
+ if (ret <= 0)
+ return 0;
+
+ uint32_t ptypes[ret];
+
+ ret = rte_eth_dev_get_supported_ptypes(portid, ptype_mask, ptypes, ret);
+ for (i = 0; i < ret; ++i) {
+ if (ptypes[i] & RTE_PTYPE_L3_IPV4)
+ ptype_l3_ipv4 = 1;
+ if (ptypes[i] & RTE_PTYPE_L3_IPV6)
+ ptype_l3_ipv6 = 1;
+ }
+
+ if (ptype_l3_ipv4 == 0)
+ printf("port %d cannot parse RTE_PTYPE_L3_IPV4\n", portid);
+
+ if (ptype_l3_ipv6 == 0)
+ printf("port %d cannot parse RTE_PTYPE_L3_IPV6\n", portid);
+
+ if (ptype_l3_ipv4 && ptype_l3_ipv6)
+ return 1;
+
+ return 0;
+
+}
+
+/* Parse packet type of a packet by SW */
+static inline void
+parse_ptype(struct rte_mbuf *m)
+{
+ struct ether_hdr *eth_hdr;
+ uint32_t packet_type = RTE_PTYPE_UNKNOWN;
+ uint16_t ether_type;
+
+ eth_hdr = rte_pktmbuf_mtod(m, struct ether_hdr *);
+ ether_type = eth_hdr->ether_type;
+ if (ether_type == rte_cpu_to_be_16(ETHER_TYPE_IPv4))
+ packet_type |= RTE_PTYPE_L3_IPV4_EXT_UNKNOWN;
+ else if (ether_type == rte_cpu_to_be_16(ETHER_TYPE_IPv6))
+ packet_type |= RTE_PTYPE_L3_IPV6_EXT_UNKNOWN;
+
+ m->packet_type = packet_type;
+}
+
+/* callback function to detect packet type for a queue of a port */
+static uint16_t
+cb_parse_ptype(uint8_t port __rte_unused, uint16_t queue __rte_unused,
+ struct rte_mbuf *pkts[], uint16_t nb_pkts,
+ uint16_t max_pkts __rte_unused,
+ void *user_param __rte_unused)
+{
+ uint16_t i;
+
+ for (i = 0; i < nb_pkts; ++i)
+ parse_ptype(pkts[i]);
+
+ return nb_pkts;
+}
+
static int
init_routing_table(void)
{
struct rte_mempool *mp;
struct rte_lpm *lpm;
struct rte_lpm6 *lpm6;
+ struct rte_lpm_config lpm_config;
int socket;
unsigned lcore_id;
if (socket_direct_pool[socket] == NULL) {
RTE_LOG(INFO, IP_FRAG, "Creating direct mempool on socket %i\n",
socket);
- rte_snprintf(buf, sizeof(buf), "pool_direct_%i", socket);
-
- mp = rte_mempool_create(buf, NB_MBUF,
- MBUF_SIZE, 32,
- sizeof(struct rte_pktmbuf_pool_private),
- rte_pktmbuf_pool_init, NULL,
- rte_pktmbuf_init, NULL,
- socket, 0);
+ snprintf(buf, sizeof(buf), "pool_direct_%i", socket);
+
+ mp = rte_pktmbuf_pool_create(buf, NB_MBUF, 32,
+ 0, RTE_MBUF_DEFAULT_BUF_SIZE, socket);
if (mp == NULL) {
RTE_LOG(ERR, IP_FRAG, "Cannot create direct mempool\n");
return -1;
if (socket_indirect_pool[socket] == NULL) {
RTE_LOG(INFO, IP_FRAG, "Creating indirect mempool on socket %i\n",
socket);
- rte_snprintf(buf, sizeof(buf), "pool_indirect_%i", socket);
-
- mp = rte_mempool_create(buf, NB_MBUF,
- sizeof(struct rte_mbuf), 32,
- 0,
- NULL, NULL,
- rte_pktmbuf_init, NULL,
- socket, 0);
+ snprintf(buf, sizeof(buf), "pool_indirect_%i", socket);
+
+ mp = rte_pktmbuf_pool_create(buf, NB_MBUF, 32, 0, 0,
+ socket);
if (mp == NULL) {
RTE_LOG(ERR, IP_FRAG, "Cannot create indirect mempool\n");
return -1;
if (socket_lpm[socket] == NULL) {
RTE_LOG(INFO, IP_FRAG, "Creating LPM table on socket %i\n", socket);
- rte_snprintf(buf, sizeof(buf), "IP_FRAG_LPM_%i", socket);
+ snprintf(buf, sizeof(buf), "IP_FRAG_LPM_%i", socket);
+
+ lpm_config.max_rules = LPM_MAX_RULES;
+ lpm_config.number_tbl8s = 256;
+ lpm_config.flags = 0;
- lpm = rte_lpm_create(buf, socket, LPM_MAX_RULES, 0);
+ lpm = rte_lpm_create(buf, socket, &lpm_config);
if (lpm == NULL) {
RTE_LOG(ERR, IP_FRAG, "Cannot create LPM table\n");
return -1;
if (socket_lpm6[socket] == NULL) {
RTE_LOG(INFO, IP_FRAG, "Creating LPM6 table on socket %i\n", socket);
- rte_snprintf(buf, sizeof(buf), "IP_FRAG_LPM_%i", socket);
+ snprintf(buf, sizeof(buf), "IP_FRAG_LPM_%i", socket);
- lpm6 = rte_lpm6_create("IP_FRAG_LPM6", socket, &lpm6_config);
+ lpm6 = rte_lpm6_create(buf, socket, &lpm6_config);
if (lpm6 == NULL) {
RTE_LOG(ERR, IP_FRAG, "Cannot create LPM table\n");
return -1;
}
int
-MAIN(int argc, char **argv)
+main(int argc, char **argv)
{
struct lcore_queue_conf *qconf;
+ struct rte_eth_dev_info dev_info;
+ struct rte_eth_txconf *txconf;
struct rx_queue *rxq;
int socket, ret;
unsigned nb_ports;
if (ret < 0)
rte_exit(EXIT_FAILURE, "Invalid arguments");
- if (rte_eal_pci_probe() < 0)
- rte_panic("Cannot probe PCI\n");
-
nb_ports = rte_eth_dev_count();
- if (nb_ports > RTE_MAX_ETHPORTS)
- nb_ports = RTE_MAX_ETHPORTS;
- else if (nb_ports == 0)
+ if (nb_ports == 0)
rte_exit(EXIT_FAILURE, "No ports found!\n");
nb_lcores = rte_lcore_count();
qconf = &lcore_queue_conf[rx_lcore_id];
+ /* limit the frame size to the maximum supported by NIC */
+ rte_eth_dev_info_get(portid, &dev_info);
+ port_conf.rxmode.max_rx_pkt_len = RTE_MIN(
+ dev_info.max_rx_pktlen, port_conf.rxmode.max_rx_pkt_len);
+
/* get the lcore_id for this port */
while (rte_lcore_is_enabled(rx_lcore_id) == 0 ||
qconf->n_rx_queue == (unsigned)rx_queue_per_lcore) {
qconf = &lcore_queue_conf[rx_lcore_id];
}
- socket = rte_eth_dev_socket_id(portid);
+ socket = (int) rte_lcore_to_socket_id(rx_lcore_id);
if (socket == SOCKET_ID_ANY)
socket = 0;
/* init one RX queue */
ret = rte_eth_rx_queue_setup(portid, 0, nb_rxd,
- socket, &rx_conf,
+ socket, NULL,
socket_direct_pool[socket]);
if (ret < 0) {
printf("\n");
socket = (int) rte_lcore_to_socket_id(lcore_id);
printf("txq=%u,%d ", lcore_id, queueid);
fflush(stdout);
+
+ txconf = &dev_info.default_txconf;
+ txconf->txq_flags = 0;
ret = rte_eth_tx_queue_setup(portid, queueid, nb_txd,
- socket, &tx_conf);
+ socket, txconf);
if (ret < 0) {
printf("\n");
rte_exit(EXIT_FAILURE, "rte_eth_tx_queue_setup: "
ret, portid);
rte_eth_promiscuous_enable(portid);
+
+ if (check_ptype(portid) == 0) {
+ rte_eth_add_rx_callback(portid, 0, cb_parse_ptype, NULL);
+ printf("Add Rx callback function to detect L3 packet type by SW :"
+ " port = %d\n", portid);
+ }
}
if (init_routing_table() < 0)
git.droids-corp.org / dpdk.git / blobdiff