#include <stdint.h>
#include <inttypes.h>
#include <sys/types.h>
-#include <string.h>
#include <sys/queue.h>
#include <netinet/in.h>
#include <setjmp.h>
#include <rte_memcpy.h>
#include <rte_memzone.h>
#include <rte_eal.h>
-#include <rte_per_lcore.h>
#include <rte_launch.h>
#include <rte_atomic.h>
#include <rte_cycles.h>
#include <rte_debug.h>
#include <rte_ether.h>
#include <rte_ethdev.h>
-#include <rte_ring.h>
#include <rte_mempool.h>
#include <rte_mbuf.h>
.hw_ip_checksum = 0, /**< IP checksum offload disabled */
.hw_vlan_filter = 0, /**< VLAN filtering disabled */
.jumbo_frame = 0, /**< Jumbo Frame Support disabled */
- .hw_strip_crc = 0, /**< CRC stripped by hardware */
+ .hw_strip_crc = 1, /**< CRC stripped by hardware */
},
.txmode = {
.mq_mode = ETH_MQ_TX_NONE,
argv[optind-1] = prgname;
ret = optind-1;
- optind = 0; /* reset getopt lib */
+ optind = 1; /* reset getopt lib */
return ret;
}
* Pointer to(address of) the parameters.
*
* @return
- * void.
+ * int.
*/
-static void
-lsi_event_callback(uint8_t port_id, enum rte_eth_event_type type, void *param)
+static int
+lsi_event_callback(uint8_t port_id, enum rte_eth_event_type type, void *param,
+ void *ret_param)
{
struct rte_eth_link link;
RTE_SET_USED(param);
+ RTE_SET_USED(ret_param);
printf("\n\nIn registered callback...\n");
printf("Event type: %s\n", type == RTE_ETH_EVENT_INTR_LSC ? "LSC interrupt" : "unknown event");
("full-duplex") : ("half-duplex"));
} else
printf("Port %d Link Down\n\n", port_id);
+
+ return 0;
}
/* Check the link status of all ports in up to 9s, and print them finally */
continue;
}
/* clear all_ports_up flag if any link down */
- if (link.link_status == 0) {
+ if (link.link_status == ETH_LINK_DOWN) {
all_ports_up = 0;
break;
}
if (nb_ports == 0)
rte_panic("No Ethernet port - bye\n");
- if (nb_ports > RTE_MAX_ETHPORTS)
- nb_ports = RTE_MAX_ETHPORTS;
-
/*
* Each logical core is assigned a dedicated TX queue on each port.
*/
rte_exit(EXIT_FAILURE, "Cannot configure device: err=%d, port=%u\n",
ret, (unsigned) portid);
+ ret = rte_eth_dev_adjust_nb_rx_tx_desc(portid, &nb_rxd,
+ &nb_txd);
+ if (ret < 0)
+ rte_exit(EXIT_FAILURE,
+ "rte_eth_dev_adjust_nb_rx_tx_desc: err=%d, port=%u\n",
+ ret, (unsigned) portid);
+
/* register lsi interrupt callback, need to be after
* rte_eth_dev_configure(). if (intr_conf.lsc == 0), no
* lsc interrupt will be present, and below callback to