uint8_t priority; /**< VLAN User Priority. */
};
+/**
+ * @warning
+ * @b EXPERIMENTAL: this API may change, or be removed, without prior notice
+ *
+ * A structure used to retrieve information of queue based PFC.
+ */
+struct rte_eth_pfc_queue_info {
+ /**
+ * Maximum supported traffic class as per PFC (802.1Qbb) specification.
+ */
+ uint8_t tc_max;
+ /** PFC queue mode capabilities. */
+ enum rte_eth_fc_mode mode_capa;
+};
+
+/**
+ * @warning
+ * @b EXPERIMENTAL: this API may change, or be removed, without prior notice
+ *
+ * A structure used to configure Ethernet priority flow control parameters for
+ * ethdev queues.
+ *
+ * rte_eth_pfc_queue_conf::rx_pause structure shall be used to configure given
+ * tx_qid with corresponding tc. When ethdev device receives PFC frame with
+ * rte_eth_pfc_queue_conf::rx_pause::tc, traffic will be paused on
+ * rte_eth_pfc_queue_conf::rx_pause::tx_qid for that tc.
+ *
+ * rte_eth_pfc_queue_conf::tx_pause structure shall be used to configure given
+ * rx_qid. When rx_qid is congested, PFC frames are generated with
+ * rte_eth_pfc_queue_conf::rx_pause::tc and
+ * rte_eth_pfc_queue_conf::rx_pause::pause_time to the peer.
+ */
+struct rte_eth_pfc_queue_conf {
+ enum rte_eth_fc_mode mode; /**< Link flow control mode */
+
+ struct {
+ uint16_t tx_qid; /**< Tx queue ID */
+ /** Traffic class as per PFC (802.1Qbb) spec. The value must be
+ * in the range [0, rte_eth_pfc_queue_info::tx_max - 1]
+ */
+ uint8_t tc;
+ } rx_pause; /* Valid when (mode == FC_RX_PAUSE || mode == FC_FULL) */
+
+ struct {
+ uint16_t pause_time; /**< Pause quota in the Pause frame */
+ uint16_t rx_qid; /**< Rx queue ID */
+ /** Traffic class as per PFC (802.1Qbb) spec. The value must be
+ * in the range [0, rte_eth_pfc_queue_info::tx_max - 1]
+ */
+ uint8_t tc;
+ } tx_pause; /* Valid when (mode == FC_TX_PAUSE || mode == FC_FULL) */
+};
+
/**
* Tunnel type for device-specific classifier configuration.
* @see rte_eth_udp_tunnel
int rte_eth_dev_mac_addr_add(uint16_t port_id, struct rte_ether_addr *mac_addr,
uint32_t pool);
+/**
+ * @warning
+ * @b EXPERIMENTAL: this API may change without prior notice.
+ *
+ * Retrieve the information for queue based PFC.
+ *
+ * @param port_id
+ * The port identifier of the Ethernet device.
+ * @param pfc_queue_info
+ * A pointer to a structure of type *rte_eth_pfc_queue_info* to be filled with
+ * the information about queue based PFC.
+ * @return
+ * - (0) if successful.
+ * - (-ENOTSUP) if support for priority_flow_ctrl_queue_info_get does not exist.
+ * - (-ENODEV) if *port_id* invalid.
+ * - (-EINVAL) if bad parameter.
+ */
+__rte_experimental
+int rte_eth_dev_priority_flow_ctrl_queue_info_get(uint16_t port_id,
+ struct rte_eth_pfc_queue_info *pfc_queue_info);
+
+/**
+ * @warning
+ * @b EXPERIMENTAL: this API may change without prior notice.
+ *
+ * Configure the queue based priority flow control for a given queue
+ * for Ethernet device.
+ *
+ * @note When an ethdev port switches to queue based PFC mode, the
+ * unconfigured queues shall be configured by the driver with
+ * default values such as lower priority value for TC etc.
+ *
+ * @param port_id
+ * The port identifier of the Ethernet device.
+ * @param pfc_queue_conf
+ * The pointer to the structure of the priority flow control parameters
+ * for the queue.
+ * @return
+ * - (0) if successful.
+ * - (-ENOTSUP) if hardware doesn't support queue based PFC mode.
+ * - (-ENODEV) if *port_id* invalid.
+ * - (-EINVAL) if bad parameter
+ * - (-EIO) if flow control setup queue failure
+ */
+__rte_experimental
+int rte_eth_dev_priority_flow_ctrl_queue_configure(uint16_t port_id,
+ struct rte_eth_pfc_queue_conf *pfc_queue_conf);
+
/**
* Remove a MAC address from the internal array of addresses.
*