/*-
* BSD LICENSE
*
- * Copyright(c) 2010-2014 Intel Corporation. All rights reserved.
+ * Copyright(c) 2010-2015 Intel Corporation. All rights reserved.
* All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
#include <stdint.h>
+/* Use this macro to check if LRO API is supported */
+#define RTE_ETHDEV_HAS_LRO_SUPPORT
+
#include <rte_log.h>
#include <rte_interrupts.h>
#include <rte_pci.h>
-#include <rte_mbuf.h>
+#include <rte_dev.h>
+#include <rte_devargs.h>
#include "rte_ether.h"
+#include "rte_eth_ctrl.h"
+#include "rte_dev_info.h"
+
+struct rte_mbuf;
/**
* A structure used to retrieve statistics for an Ethernet port.
uint64_t opackets; /**< Total number of successfully transmitted packets.*/
uint64_t ibytes; /**< Total number of successfully received bytes. */
uint64_t obytes; /**< Total number of successfully transmitted bytes. */
- uint64_t imissed; /**< Total of RX missed packets (e.g full FIFO). */
- uint64_t ibadcrc; /**< Total of RX packets with CRC error. */
- uint64_t ibadlen; /**< Total of RX packets with bad length. */
+ uint64_t imissed;
+ /**< Deprecated; Total of RX missed packets (e.g full FIFO). */
+ uint64_t ibadcrc;
+ /**< Deprecated; Total of RX packets with CRC error. */
+ uint64_t ibadlen;
+ /**< Deprecated; Total of RX packets with bad length. */
uint64_t ierrors; /**< Total number of erroneous received packets. */
uint64_t oerrors; /**< Total number of failed transmitted packets. */
- uint64_t imcasts; /**< Total number of multicast received packets. */
+ uint64_t imcasts;
+ /**< Deprecated; Total number of multicast received packets. */
uint64_t rx_nombuf; /**< Total number of RX mbuf allocation failures. */
- uint64_t fdirmatch; /**< Total number of RX packets matching a filter. */
- uint64_t fdirmiss; /**< Total number of RX packets not matching any filter. */
- uint64_t tx_pause_xon; /**< Total nb. of XON pause frame sent. */
- uint64_t rx_pause_xon; /**< Total nb. of XON pause frame received. */
- uint64_t tx_pause_xoff; /**< Total nb. of XOFF pause frame sent. */
- uint64_t rx_pause_xoff; /**< Total nb. of XOFF pause frame received. */
+ uint64_t fdirmatch;
+ /**< Deprecated; Total number of RX packets matching a filter. */
+ uint64_t fdirmiss;
+ /**< Deprecated; Total number of RX packets not matching any filter. */
+ uint64_t tx_pause_xon;
+ /**< Deprecated; Total nb. of XON pause frame sent. */
+ uint64_t rx_pause_xon;
+ /**< Deprecated; Total nb. of XON pause frame received. */
+ uint64_t tx_pause_xoff;
+ /**< Deprecated; Total nb. of XOFF pause frame sent. */
+ uint64_t rx_pause_xoff;
+ /**< Deprecated; Total nb. of XOFF pause frame received. */
uint64_t q_ipackets[RTE_ETHDEV_QUEUE_STAT_CNTRS];
/**< Total number of queue RX packets. */
uint64_t q_opackets[RTE_ETHDEV_QUEUE_STAT_CNTRS];
uint8_t wthresh; /**< Ring writeback threshold. */
};
+/**
+ * Simple flags are used for rte_eth_conf.rxmode.mq_mode.
+ */
+#define ETH_MQ_RX_RSS_FLAG 0x1
+#define ETH_MQ_RX_DCB_FLAG 0x2
+#define ETH_MQ_RX_VMDQ_FLAG 0x4
+
/**
* A set of values to identify what method is to be used to route
* packets to multiple queues.
*/
enum rte_eth_rx_mq_mode {
- ETH_MQ_RX_NONE = 0, /**< None of DCB,RSS or VMDQ mode */
-
- ETH_MQ_RX_RSS, /**< For RX side, only RSS is on */
- ETH_MQ_RX_DCB, /**< For RX side,only DCB is on. */
- ETH_MQ_RX_DCB_RSS, /**< Both DCB and RSS enable */
-
- ETH_MQ_RX_VMDQ_ONLY, /**< Only VMDQ, no RSS nor DCB */
- ETH_MQ_RX_VMDQ_RSS, /**< RSS mode with VMDQ */
- ETH_MQ_RX_VMDQ_DCB, /**< Use VMDQ+DCB to route traffic to queues */
- ETH_MQ_RX_VMDQ_DCB_RSS, /**< Enable both VMDQ and DCB in VMDq */
+ /** None of DCB,RSS or VMDQ mode */
+ ETH_MQ_RX_NONE = 0,
+
+ /** For RX side, only RSS is on */
+ ETH_MQ_RX_RSS = ETH_MQ_RX_RSS_FLAG,
+ /** For RX side,only DCB is on. */
+ ETH_MQ_RX_DCB = ETH_MQ_RX_DCB_FLAG,
+ /** Both DCB and RSS enable */
+ ETH_MQ_RX_DCB_RSS = ETH_MQ_RX_RSS_FLAG | ETH_MQ_RX_DCB_FLAG,
+
+ /** Only VMDQ, no RSS nor DCB */
+ ETH_MQ_RX_VMDQ_ONLY = ETH_MQ_RX_VMDQ_FLAG,
+ /** RSS mode with VMDQ */
+ ETH_MQ_RX_VMDQ_RSS = ETH_MQ_RX_RSS_FLAG | ETH_MQ_RX_VMDQ_FLAG,
+ /** Use VMDQ+DCB to route traffic to queues */
+ ETH_MQ_RX_VMDQ_DCB = ETH_MQ_RX_VMDQ_FLAG | ETH_MQ_RX_DCB_FLAG,
+ /** Enable both VMDQ and DCB in VMDq */
+ ETH_MQ_RX_VMDQ_DCB_RSS = ETH_MQ_RX_RSS_FLAG | ETH_MQ_RX_DCB_FLAG |
+ ETH_MQ_RX_VMDQ_FLAG,
};
/**
enum rte_eth_rx_mq_mode mq_mode;
uint32_t max_rx_pkt_len; /**< Only used if jumbo_frame enabled. */
uint16_t split_hdr_size; /**< hdr buf size (header_split enabled).*/
- uint8_t header_split : 1, /**< Header Split enable. */
+ uint16_t header_split : 1, /**< Header Split enable. */
hw_ip_checksum : 1, /**< IP/UDP/TCP checksum offload enable. */
hw_vlan_filter : 1, /**< VLAN filter enable. */
hw_vlan_strip : 1, /**< VLAN strip enable. */
hw_vlan_extend : 1, /**< Extended VLAN enable. */
jumbo_frame : 1, /**< Jumbo Frame Receipt enable. */
- hw_strip_crc : 1; /**< Enable CRC stripping by hardware. */
+ hw_strip_crc : 1, /**< Enable CRC stripping by hardware. */
+ enable_scatter : 1, /**< Enable scatter packets rx handler */
+ enable_lro : 1; /**< Enable LRO */
};
/**
uint64_t rss_hf; /**< Hash functions to apply - see below. */
};
-/* Supported RSS offloads */
-/* for 1G & 10G */
-#define ETH_RSS_IPV4_SHIFT 0
-#define ETH_RSS_IPV4_TCP_SHIFT 1
-#define ETH_RSS_IPV6_SHIFT 2
-#define ETH_RSS_IPV6_EX_SHIFT 3
-#define ETH_RSS_IPV6_TCP_SHIFT 4
-#define ETH_RSS_IPV6_TCP_EX_SHIFT 5
-#define ETH_RSS_IPV4_UDP_SHIFT 6
-#define ETH_RSS_IPV6_UDP_SHIFT 7
-#define ETH_RSS_IPV6_UDP_EX_SHIFT 8
-/* for 40G only */
-#define ETH_RSS_NONF_IPV4_UDP_SHIFT 31
-#define ETH_RSS_NONF_IPV4_TCP_SHIFT 33
-#define ETH_RSS_NONF_IPV4_SCTP_SHIFT 34
-#define ETH_RSS_NONF_IPV4_OTHER_SHIFT 35
-#define ETH_RSS_FRAG_IPV4_SHIFT 36
-#define ETH_RSS_NONF_IPV6_UDP_SHIFT 41
-#define ETH_RSS_NONF_IPV6_TCP_SHIFT 43
-#define ETH_RSS_NONF_IPV6_SCTP_SHIFT 44
-#define ETH_RSS_NONF_IPV6_OTHER_SHIFT 45
-#define ETH_RSS_FRAG_IPV6_SHIFT 46
-#define ETH_RSS_FCOE_OX_SHIFT 48
-#define ETH_RSS_FCOE_RX_SHIFT 49
-#define ETH_RSS_FCOE_OTHER_SHIFT 50
-#define ETH_RSS_L2_PAYLOAD_SHIFT 63
-
-/* for 1G & 10G */
-#define ETH_RSS_IPV4 ((uint16_t)1 << ETH_RSS_IPV4_SHIFT)
-#define ETH_RSS_IPV4_TCP ((uint16_t)1 << ETH_RSS_IPV4_TCP_SHIFT)
-#define ETH_RSS_IPV6 ((uint16_t)1 << ETH_RSS_IPV6_SHIFT)
-#define ETH_RSS_IPV6_EX ((uint16_t)1 << ETH_RSS_IPV6_EX_SHIFT)
-#define ETH_RSS_IPV6_TCP ((uint16_t)1 << ETH_RSS_IPV6_TCP_SHIFT)
-#define ETH_RSS_IPV6_TCP_EX ((uint16_t)1 << ETH_RSS_IPV6_TCP_EX_SHIFT)
-#define ETH_RSS_IPV4_UDP ((uint16_t)1 << ETH_RSS_IPV4_UDP_SHIFT)
-#define ETH_RSS_IPV6_UDP ((uint16_t)1 << ETH_RSS_IPV6_UDP_SHIFT)
-#define ETH_RSS_IPV6_UDP_EX ((uint16_t)1 << ETH_RSS_IPV6_UDP_EX_SHIFT)
-/* for 40G only */
-#define ETH_RSS_NONF_IPV4_UDP ((uint64_t)1 << ETH_RSS_NONF_IPV4_UDP_SHIFT)
-#define ETH_RSS_NONF_IPV4_TCP ((uint64_t)1 << ETH_RSS_NONF_IPV4_TCP_SHIFT)
-#define ETH_RSS_NONF_IPV4_SCTP ((uint64_t)1 << ETH_RSS_NONF_IPV4_SCTP_SHIFT)
-#define ETH_RSS_NONF_IPV4_OTHER ((uint64_t)1 << ETH_RSS_NONF_IPV4_OTHER_SHIFT)
-#define ETH_RSS_FRAG_IPV4 ((uint64_t)1 << ETH_RSS_FRAG_IPV4_SHIFT)
-#define ETH_RSS_NONF_IPV6_UDP ((uint64_t)1 << ETH_RSS_NONF_IPV6_UDP_SHIFT)
-#define ETH_RSS_NONF_IPV6_TCP ((uint64_t)1 << ETH_RSS_NONF_IPV6_TCP_SHIFT)
-#define ETH_RSS_NONF_IPV6_SCTP ((uint64_t)1 << ETH_RSS_NONF_IPV6_SCTP_SHIFT)
-#define ETH_RSS_NONF_IPV6_OTHER ((uint64_t)1 << ETH_RSS_NONF_IPV6_OTHER_SHIFT)
-#define ETH_RSS_FRAG_IPV6 ((uint64_t)1 << ETH_RSS_FRAG_IPV6_SHIFT)
-#define ETH_RSS_FCOE_OX ((uint64_t)1 << ETH_RSS_FCOE_OX_SHIFT) /* not used */
-#define ETH_RSS_FCOE_RX ((uint64_t)1 << ETH_RSS_FCOE_RX_SHIFT) /* not used */
-#define ETH_RSS_FCOE_OTHER ((uint64_t)1 << ETH_RSS_FCOE_OTHER_SHIFT) /* not used */
-#define ETH_RSS_L2_PAYLOAD ((uint64_t)1 << ETH_RSS_L2_PAYLOAD_SHIFT)
+/*
+ * The RSS offload types are defined based on flow types which are defined
+ * in rte_eth_ctrl.h. Different NIC hardwares may support different RSS offload
+ * types. The supported flow types or RSS offload types can be queried by
+ * rte_eth_dev_info_get().
+ */
+#define ETH_RSS_IPV4 (1ULL << RTE_ETH_FLOW_IPV4)
+#define ETH_RSS_FRAG_IPV4 (1ULL << RTE_ETH_FLOW_FRAG_IPV4)
+#define ETH_RSS_NONFRAG_IPV4_TCP (1ULL << RTE_ETH_FLOW_NONFRAG_IPV4_TCP)
+#define ETH_RSS_NONFRAG_IPV4_UDP (1ULL << RTE_ETH_FLOW_NONFRAG_IPV4_UDP)
+#define ETH_RSS_NONFRAG_IPV4_SCTP (1ULL << RTE_ETH_FLOW_NONFRAG_IPV4_SCTP)
+#define ETH_RSS_NONFRAG_IPV4_OTHER (1ULL << RTE_ETH_FLOW_NONFRAG_IPV4_OTHER)
+#define ETH_RSS_IPV6 (1ULL << RTE_ETH_FLOW_IPV6)
+#define ETH_RSS_FRAG_IPV6 (1ULL << RTE_ETH_FLOW_FRAG_IPV6)
+#define ETH_RSS_NONFRAG_IPV6_TCP (1ULL << RTE_ETH_FLOW_NONFRAG_IPV6_TCP)
+#define ETH_RSS_NONFRAG_IPV6_UDP (1ULL << RTE_ETH_FLOW_NONFRAG_IPV6_UDP)
+#define ETH_RSS_NONFRAG_IPV6_SCTP (1ULL << RTE_ETH_FLOW_NONFRAG_IPV6_SCTP)
+#define ETH_RSS_NONFRAG_IPV6_OTHER (1ULL << RTE_ETH_FLOW_NONFRAG_IPV6_OTHER)
+#define ETH_RSS_L2_PAYLOAD (1ULL << RTE_ETH_FLOW_L2_PAYLOAD)
+#define ETH_RSS_IPV6_EX (1ULL << RTE_ETH_FLOW_IPV6_EX)
+#define ETH_RSS_IPV6_TCP_EX (1ULL << RTE_ETH_FLOW_IPV6_TCP_EX)
+#define ETH_RSS_IPV6_UDP_EX (1ULL << RTE_ETH_FLOW_IPV6_UDP_EX)
#define ETH_RSS_IP ( \
- ETH_RSS_IPV4 | \
- ETH_RSS_IPV6 | \
- ETH_RSS_NONF_IPV4_OTHER | \
- ETH_RSS_FRAG_IPV4 | \
- ETH_RSS_NONF_IPV6_OTHER | \
- ETH_RSS_FRAG_IPV6)
+ ETH_RSS_IPV4 | \
+ ETH_RSS_FRAG_IPV4 | \
+ ETH_RSS_NONFRAG_IPV4_OTHER | \
+ ETH_RSS_IPV6 | \
+ ETH_RSS_FRAG_IPV6 | \
+ ETH_RSS_NONFRAG_IPV6_OTHER | \
+ ETH_RSS_IPV6_EX)
+
#define ETH_RSS_UDP ( \
- ETH_RSS_IPV4 | \
- ETH_RSS_IPV6 | \
- ETH_RSS_IPV4_UDP | \
- ETH_RSS_IPV6_UDP | \
- ETH_RSS_IPV6_UDP_EX | \
- ETH_RSS_NONF_IPV4_UDP | \
- ETH_RSS_NONF_IPV6_UDP)
+ ETH_RSS_NONFRAG_IPV4_UDP | \
+ ETH_RSS_NONFRAG_IPV6_UDP | \
+ ETH_RSS_IPV6_UDP_EX)
+
+#define ETH_RSS_TCP ( \
+ ETH_RSS_NONFRAG_IPV4_TCP | \
+ ETH_RSS_NONFRAG_IPV6_TCP | \
+ ETH_RSS_IPV6_TCP_EX)
+
+#define ETH_RSS_SCTP ( \
+ ETH_RSS_NONFRAG_IPV4_SCTP | \
+ ETH_RSS_NONFRAG_IPV6_SCTP)
+
/**< Mask of valid RSS hash protocols */
#define ETH_RSS_PROTO_MASK ( \
- ETH_RSS_IPV4 | \
- ETH_RSS_IPV4_TCP | \
- ETH_RSS_IPV6 | \
- ETH_RSS_IPV6_EX | \
- ETH_RSS_IPV6_TCP | \
- ETH_RSS_IPV6_TCP_EX | \
- ETH_RSS_IPV4_UDP | \
- ETH_RSS_IPV6_UDP | \
- ETH_RSS_IPV6_UDP_EX | \
- ETH_RSS_NONF_IPV4_UDP | \
- ETH_RSS_NONF_IPV4_TCP | \
- ETH_RSS_NONF_IPV4_SCTP | \
- ETH_RSS_NONF_IPV4_OTHER | \
- ETH_RSS_FRAG_IPV4 | \
- ETH_RSS_NONF_IPV6_UDP | \
- ETH_RSS_NONF_IPV6_TCP | \
- ETH_RSS_NONF_IPV6_SCTP | \
- ETH_RSS_NONF_IPV6_OTHER | \
- ETH_RSS_FRAG_IPV6 | \
- ETH_RSS_L2_PAYLOAD)
-
-/* Definitions used for redirection table entry size */
-#define ETH_RSS_RETA_NUM_ENTRIES 128
-#define ETH_RSS_RETA_MAX_QUEUE 16
+ ETH_RSS_IPV4 | \
+ ETH_RSS_FRAG_IPV4 | \
+ ETH_RSS_NONFRAG_IPV4_TCP | \
+ ETH_RSS_NONFRAG_IPV4_UDP | \
+ ETH_RSS_NONFRAG_IPV4_SCTP | \
+ ETH_RSS_NONFRAG_IPV4_OTHER | \
+ ETH_RSS_IPV6 | \
+ ETH_RSS_FRAG_IPV6 | \
+ ETH_RSS_NONFRAG_IPV6_TCP | \
+ ETH_RSS_NONFRAG_IPV6_UDP | \
+ ETH_RSS_NONFRAG_IPV6_SCTP | \
+ ETH_RSS_NONFRAG_IPV6_OTHER | \
+ ETH_RSS_L2_PAYLOAD | \
+ ETH_RSS_IPV6_EX | \
+ ETH_RSS_IPV6_TCP_EX | \
+ ETH_RSS_IPV6_UDP_EX)
+
+/*
+ * Definitions used for redirection table entry size.
+ * Some RSS RETA sizes may not be supported by some drivers, check the
+ * documentation or the description of relevant functions for more details.
+ */
+#define ETH_RSS_RETA_SIZE_64 64
+#define ETH_RSS_RETA_SIZE_128 128
+#define ETH_RSS_RETA_SIZE_512 512
+#define RTE_RETA_GROUP_SIZE 64
/* Definitions used for VMDQ and DCB functionality */
#define ETH_VMDQ_MAX_VLAN_FILTERS 64 /**< Maximum nb. of VMDQ vlan filters. */
#define ETH_VMDQ_ACCEPT_BROADCAST 0x0008 /**< accept broadcast packets. */
#define ETH_VMDQ_ACCEPT_MULTICAST 0x0010 /**< multicast promiscuous. */
-/* Definitions used for VMDQ mirror rules setting */
-#define ETH_VMDQ_NUM_MIRROR_RULE 4 /**< Maximum nb. of mirror rules. . */
+/** Maximum nb. of vlan per mirror rule */
+#define ETH_MIRROR_MAX_VLANS 64
-#define ETH_VMDQ_POOL_MIRROR 0x0001 /**< Virtual Pool Mirroring. */
-#define ETH_VMDQ_UPLINK_MIRROR 0x0002 /**< Uplink Port Mirroring. */
-#define ETH_VMDQ_DOWNLIN_MIRROR 0x0004 /**< Downlink Port Mirroring. */
-#define ETH_VMDQ_VLAN_MIRROR 0x0008 /**< VLAN Mirroring. */
+#define ETH_MIRROR_VIRTUAL_POOL_UP 0x01 /**< Virtual Pool uplink Mirroring. */
+#define ETH_MIRROR_UPLINK_PORT 0x02 /**< Uplink Port Mirroring. */
+#define ETH_MIRROR_DOWNLINK_PORT 0x04 /**< Downlink Port Mirroring. */
+#define ETH_MIRROR_VLAN 0x08 /**< VLAN Mirroring. */
+#define ETH_MIRROR_VIRTUAL_POOL_DOWN 0x10 /**< Virtual Pool downlink Mirroring. */
/**
* A structure used to configure VLAN traffic mirror of an Ethernet port.
*/
struct rte_eth_vlan_mirror {
uint64_t vlan_mask; /**< mask for valid VLAN ID. */
- uint16_t vlan_id[ETH_VMDQ_MAX_VLAN_FILTERS];
- /** VLAN ID list for vlan mirror. */
+ /** VLAN ID list for vlan mirroring. */
+ uint16_t vlan_id[ETH_MIRROR_MAX_VLANS];
};
/**
* A structure used to configure traffic mirror of an Ethernet port.
*/
-struct rte_eth_vmdq_mirror_conf {
- uint8_t rule_type_mask; /**< Mirroring rule type mask we want to set */
- uint8_t dst_pool; /**< Destination pool for this mirror rule. */
+struct rte_eth_mirror_conf {
+ uint8_t rule_type; /**< Mirroring rule type */
+ uint8_t dst_pool; /**< Destination pool for this mirror rule. */
uint64_t pool_mask; /**< Bitmap of pool for pool mirroring */
- struct rte_eth_vlan_mirror vlan; /**< VLAN ID setting for VLAN mirroring */
+ /** VLAN ID setting for VLAN mirroring. */
+ struct rte_eth_vlan_mirror vlan;
};
/**
- * A structure used to configure Redirection Table of the Receive Side
- * Scaling (RSS) feature of an Ethernet port.
+ * A structure used to configure 64 entries of Redirection Table of the
+ * Receive Side Scaling (RSS) feature of an Ethernet port. To configure
+ * more than 64 entries supported by hardware, an array of this structure
+ * is needed.
*/
-struct rte_eth_rss_reta {
- /** First 64 mask bits indicate which entry(s) need to updated/queried. */
- uint64_t mask_lo;
- /** Second 64 mask bits indicate which entry(s) need to updated/queried. */
- uint64_t mask_hi;
- uint8_t reta[ETH_RSS_RETA_NUM_ENTRIES]; /**< 128 RETA entries*/
+struct rte_eth_rss_reta_entry64 {
+ uint64_t mask;
+ /**< Mask bits indicate which entries need to be updated/queried. */
+ uint8_t reta[RTE_RETA_GROUP_SIZE];
+ /**< Group of 64 redirection table entries. */
};
/**
/* This structure may be extended in future. */
struct rte_eth_dcb_rx_conf {
enum rte_eth_nb_tcs nb_tcs; /**< Possible DCB TCs, 4 or 8 TCs */
- uint8_t dcb_queue[ETH_DCB_NUM_USER_PRIORITIES];
- /**< Possible DCB queue,4 or 8. */
+ /** Traffic class each UP mapped to. */
+ uint8_t dcb_tc[ETH_DCB_NUM_USER_PRIORITIES];
};
struct rte_eth_vmdq_dcb_tx_conf {
enum rte_eth_nb_pools nb_queue_pools; /**< With DCB, 16 or 32 pools. */
- uint8_t dcb_queue[ETH_DCB_NUM_USER_PRIORITIES];
- /**< Possible DCB queue,4 or 8. */
+ /** Traffic class each UP mapped to. */
+ uint8_t dcb_tc[ETH_DCB_NUM_USER_PRIORITIES];
};
struct rte_eth_dcb_tx_conf {
enum rte_eth_nb_tcs nb_tcs; /**< Possible DCB TCs, 4 or 8 TCs. */
- uint8_t dcb_queue[ETH_DCB_NUM_USER_PRIORITIES];
- /**< Possible DCB queue,4 or 8. */
+ /** Traffic class each UP mapped to. */
+ uint8_t dcb_tc[ETH_DCB_NUM_USER_PRIORITIES];
};
struct rte_eth_vmdq_tx_conf {
uint16_t vlan_id; /**< The vlan id of the received frame */
uint64_t pools; /**< Bitmask of pools for packet rx */
} pool_map[ETH_VMDQ_MAX_VLAN_FILTERS]; /**< VMDq vlan pool maps. */
- uint8_t dcb_queue[ETH_DCB_NUM_USER_PRIORITIES];
+ uint8_t dcb_tc[ETH_DCB_NUM_USER_PRIORITIES];
/**< Selects a queue in a pool */
};
uint8_t default_pool; /**< The default pool, if applicable */
uint8_t enable_loop_back; /**< Enable VT loop back */
uint8_t nb_pool_maps; /**< We can have up to 64 filters/mappings */
+ uint32_t rx_mode; /**< Flags from ETH_VMDQ_ACCEPT_* */
struct {
uint16_t vlan_id; /**< The vlan id of the received frame */
uint64_t pools; /**< Bitmask of pools for packet rx */
struct rte_eth_thresh rx_thresh; /**< RX ring threshold registers. */
uint16_t rx_free_thresh; /**< Drives the freeing of RX descriptors. */
uint8_t rx_drop_en; /**< Drop packets if no descriptors are available. */
- uint8_t start_rx_per_q; /**< start rx per queue. */
+ uint8_t rx_deferred_start; /**< Do not start queue with rte_eth_dev_start(). */
};
#define ETH_TXQ_FLAGS_NOMULTSEGS 0x0001 /**< nb_segs=1 for all mbufs */
#define ETH_TXQ_FLAGS_NOOFFLOADS \
(ETH_TXQ_FLAGS_NOVLANOFFL | ETH_TXQ_FLAGS_NOXSUMSCTP | \
ETH_TXQ_FLAGS_NOXSUMUDP | ETH_TXQ_FLAGS_NOXSUMTCP)
+#define ETH_TXQ_FLAGS_NOXSUMS \
+ (ETH_TXQ_FLAGS_NOXSUMSCTP | ETH_TXQ_FLAGS_NOXSUMUDP | \
+ ETH_TXQ_FLAGS_NOXSUMTCP)
/**
* A structure used to configure a TX ring of an Ethernet port.
*/
struct rte_eth_txconf {
struct rte_eth_thresh tx_thresh; /**< TX ring threshold registers. */
uint16_t tx_rs_thresh; /**< Drives the setting of RS bit on TXDs. */
- uint16_t tx_free_thresh; /**< Drives the freeing of TX buffers. */
+ uint16_t tx_free_thresh; /**< Start freeing TX buffers if there are
+ less free descriptors than this value. */
+
uint32_t txq_flags; /**< Set flags for the Tx queue */
- uint8_t start_tx_per_q; /**< start tx per queue. */
+ uint8_t tx_deferred_start; /**< Do not start queue with rte_eth_dev_start(). */
};
/**
uint8_t priority; /**< VLAN User Priority. */
};
-/**
- * Flow Director setting modes: none (default), signature or perfect.
- */
-enum rte_fdir_mode {
- RTE_FDIR_MODE_NONE = 0, /**< Disable FDIR support. */
- RTE_FDIR_MODE_SIGNATURE, /**< Enable FDIR signature filter mode. */
- RTE_FDIR_MODE_PERFECT, /**< Enable FDIR perfect filter mode. */
-};
-
/**
* Memory space that can be configured to store Flow Director filters
* in the board memory.
enum rte_fdir_mode mode; /**< Flow Director mode. */
enum rte_fdir_pballoc_type pballoc; /**< Space for FDIR filters. */
enum rte_fdir_status_mode status; /**< How to report FDIR hash. */
- /** Offset of flexbytes field in RX packets (in 16-bit word units). */
- uint8_t flexbytes_offset;
/** RX queue of packets matching a "drop" filter in perfect mode. */
uint8_t drop_queue;
+ struct rte_eth_fdir_masks mask;
+ struct rte_eth_fdir_flex_conf flex_conf;
+ /**< Flex payload configuration. */
};
/**
- * Possible l4type of FDIR filters.
- */
-enum rte_l4type {
- RTE_FDIR_L4TYPE_NONE = 0, /**< None. */
- RTE_FDIR_L4TYPE_UDP, /**< UDP. */
- RTE_FDIR_L4TYPE_TCP, /**< TCP. */
- RTE_FDIR_L4TYPE_SCTP, /**< SCTP. */
-};
-
-/**
- * Select IPv4 or IPv6 FDIR filters.
+ * UDP tunneling configuration.
*/
-enum rte_iptype {
- RTE_FDIR_IPTYPE_IPV4 = 0, /**< IPv4. */
- RTE_FDIR_IPTYPE_IPV6 , /**< IPv6. */
-};
-
-/**
- * A structure used to define a FDIR packet filter.
- */
-struct rte_fdir_filter {
- uint16_t flex_bytes; /**< Flex bytes value to match. */
- uint16_t vlan_id; /**< VLAN ID value to match, 0 otherwise. */
- uint16_t port_src; /**< Source port to match, 0 otherwise. */
- uint16_t port_dst; /**< Destination port to match, 0 otherwise. */
- union {
- uint32_t ipv4_addr; /**< IPv4 source address to match. */
- uint32_t ipv6_addr[4]; /**< IPv6 source address to match. */
- } ip_src; /**< IPv4/IPv6 source address to match (union of above). */
- union {
- uint32_t ipv4_addr; /**< IPv4 destination address to match. */
- uint32_t ipv6_addr[4]; /**< IPv6 destination address to match */
- } ip_dst; /**< IPv4/IPv6 destination address to match (union of above). */
- enum rte_l4type l4type; /**< l4type to match: NONE/UDP/TCP/SCTP. */
- enum rte_iptype iptype; /**< IP packet type to match: IPv4 or IPv6. */
-};
-
-/**
- * A structure used to configure FDIR masks that are used by the device
- * to match the various fields of RX packet headers.
- * @note The only_ip_flow field has the opposite meaning compared to other
- * masks!
- */
-struct rte_fdir_masks {
- /** When set to 1, packet l4type is \b NOT relevant in filters, and
- source and destination port masks must be set to zero. */
- uint8_t only_ip_flow;
- /** If set to 1, vlan_id is relevant in filters. */
- uint8_t vlan_id;
- /** If set to 1, vlan_prio is relevant in filters. */
- uint8_t vlan_prio;
- /** If set to 1, flexbytes is relevant in filters. */
- uint8_t flexbytes;
- /** If set to 1, set the IPv6 masks. Otherwise set the IPv4 masks. */
- uint8_t set_ipv6_mask;
- /** When set to 1, comparison of destination IPv6 address with IP6AT
- registers is meaningful. */
- uint8_t comp_ipv6_dst;
- /** Mask of Destination IPv4 Address. All bits set to 1 define the
- relevant bits to use in the destination address of an IPv4 packet
- when matching it against FDIR filters. */
- uint32_t dst_ipv4_mask;
- /** Mask of Source IPv4 Address. All bits set to 1 define
- the relevant bits to use in the source address of an IPv4 packet
- when matching it against FDIR filters. */
- uint32_t src_ipv4_mask;
- /** Mask of Source IPv6 Address. All bits set to 1 define the
- relevant BYTES to use in the source address of an IPv6 packet
- when matching it against FDIR filters. */
- uint16_t dst_ipv6_mask;
- /** Mask of Destination IPv6 Address. All bits set to 1 define the
- relevant BYTES to use in the destination address of an IPv6 packet
- when matching it against FDIR filters. */
- uint16_t src_ipv6_mask;
- /** Mask of Source Port. All bits set to 1 define the relevant
- bits to use in the source port of an IP packets when matching it
- against FDIR filters. */
- uint16_t src_port_mask;
- /** Mask of Destination Port. All bits set to 1 define the relevant
- bits to use in the destination port of an IP packet when matching it
- against FDIR filters. */
- uint16_t dst_port_mask;
-};
-
-/**
- * A structure used to report the status of the flow director filters in use.
- */
-struct rte_eth_fdir {
- /** Number of filters with collision indication. */
- uint16_t collision;
- /** Number of free (non programmed) filters. */
- uint16_t free;
- /** The Lookup hash value of the added filter that updated the value
- of the MAXLEN field */
- uint16_t maxhash;
- /** Longest linked list of filters in the table. */
- uint8_t maxlen;
- /** Number of added filters. */
- uint64_t add;
- /** Number of removed filters. */
- uint64_t remove;
- /** Number of failed added filters (no more space in device). */
- uint64_t f_add;
- /** Number of failed removed filters. */
- uint64_t f_remove;
+struct rte_eth_udp_tunnel {
+ uint16_t udp_port;
+ uint8_t prot_type;
};
/**
struct rte_intr_conf {
/** enable/disable lsc interrupt. 0 (default) - disable, 1 enable */
uint16_t lsc;
+ /** enable/disable rxq interrupt. 0 (default) - disable, 1 enable */
+ uint16_t rxq;
};
/**
Read the datasheet of given ethernet controller
for details. The possible values of this field
are defined in implementation of each driver. */
- union {
+ struct {
struct rte_eth_rss_conf rss_conf; /**< Port RSS configuration */
struct rte_eth_vmdq_dcb_conf vmdq_dcb_conf;
/**< Port vmdq+dcb configuration. */
#define DEV_RX_OFFLOAD_UDP_CKSUM 0x00000004
#define DEV_RX_OFFLOAD_TCP_CKSUM 0x00000008
#define DEV_RX_OFFLOAD_TCP_LRO 0x00000010
+#define DEV_RX_OFFLOAD_QINQ_STRIP 0x00000020
/**
* TX offload capabilities of a device.
#define DEV_TX_OFFLOAD_SCTP_CKSUM 0x00000010
#define DEV_TX_OFFLOAD_TCP_TSO 0x00000020
#define DEV_TX_OFFLOAD_UDP_TSO 0x00000040
+#define DEV_TX_OFFLOAD_OUTER_IPV4_CKSUM 0x00000080 /**< Used for tunneling packet. */
+#define DEV_TX_OFFLOAD_QINQ_INSERT 0x00000100
struct rte_eth_dev_info {
struct rte_pci_device *pci_dev; /**< Device PCI information. */
uint16_t max_vmdq_pools; /**< Maximum number of VMDq pools. */
uint32_t rx_offload_capa; /**< Device RX offload capabilities. */
uint32_t tx_offload_capa; /**< Device TX offload capabilities. */
+ uint16_t reta_size;
+ /**< Device redirection table size, the total number of entries. */
+ uint8_t hash_key_size; /**< Hash key size in bytes */
+ /** Bit mask of RSS offloads, the bit offset also means flow type */
+ uint64_t flow_type_rss_offloads;
+ struct rte_eth_rxconf default_rxconf; /**< Default RX configuration */
+ struct rte_eth_txconf default_txconf; /**< Default TX configuration */
+ uint16_t vmdq_queue_base; /**< First queue ID for VMDQ pools. */
+ uint16_t vmdq_queue_num; /**< Queue number for VMDQ pools. */
+ uint16_t vmdq_pool_base; /**< First ID of VMDQ pools. */
};
-struct rte_eth_dev;
-
-struct rte_eth_dev_callback;
-/** @internal Structure to keep track of registered callbacks */
-TAILQ_HEAD(rte_eth_dev_cb_list, rte_eth_dev_callback);
-
-#define TCP_UGR_FLAG 0x20
-#define TCP_ACK_FLAG 0x10
-#define TCP_PSH_FLAG 0x08
-#define TCP_RST_FLAG 0x04
-#define TCP_SYN_FLAG 0x02
-#define TCP_FIN_FLAG 0x01
-#define TCP_FLAG_ALL 0x3F
+/** Maximum name length for extended statistics counters */
+#define RTE_ETH_XSTATS_NAME_SIZE 64
/**
- * A structure used to define an ethertype filter.
+ * An Ethernet device extended statistic structure
+ *
+ * This structure is used by ethdev->eth_xstats_get() to provide
+ * statistics that are not provided in the generic rte_eth_stats
+ * structure.
*/
-struct rte_ethertype_filter {
- uint16_t ethertype; /**< little endian. */
- uint8_t priority_en; /**< compare priority enable. */
- uint8_t priority;
+struct rte_eth_xstats {
+ char name[RTE_ETH_XSTATS_NAME_SIZE];
+ uint64_t value;
};
-/**
- * A structure used to define an syn filter.
- */
-struct rte_syn_filter {
- uint8_t hig_pri; /**< 1 means higher pri than 2tuple, 5tupe,
- and flex filter, 0 means lower pri. */
-};
+#define ETH_DCB_NUM_TCS 8
+#define ETH_MAX_VMDQ_POOL 64
/**
- * A structure used to define a 2tuple filter.
+ * A structure used to get the information of queue and
+ * TC mapping on both TX and RX paths.
*/
-struct rte_2tuple_filter {
- uint16_t dst_port; /**< big endian. */
- uint8_t protocol;
- uint8_t tcp_flags;
- uint16_t priority; /**< used when more than one filter matches. */
- uint8_t dst_port_mask:1, /**< if mask is 1b, means not compare. */
- protocol_mask:1;
+struct rte_eth_dcb_tc_queue_mapping {
+ /** rx queues assigned to tc per Pool */
+ struct {
+ uint8_t base;
+ uint8_t nb_queue;
+ } tc_rxq[ETH_MAX_VMDQ_POOL][ETH_DCB_NUM_TCS];
+ /** rx queues assigned to tc per Pool */
+ struct {
+ uint8_t base;
+ uint8_t nb_queue;
+ } tc_txq[ETH_MAX_VMDQ_POOL][ETH_DCB_NUM_TCS];
};
/**
- * A structure used to define a flex filter.
+ * A structure used to get the information of DCB.
+ * It includes TC UP mapping and queue TC mapping.
*/
-struct rte_flex_filter {
- uint16_t len;
- uint32_t dwords[32]; /**< flex bytes in big endian. */
- uint8_t mask[16]; /**< if mask bit is 1b, do not compare
- corresponding byte in dwords. */
- uint8_t priority;
+struct rte_eth_dcb_info {
+ uint8_t nb_tcs; /**< number of TCs */
+ uint8_t prio_tc[ETH_DCB_NUM_USER_PRIORITIES]; /**< Priority to tc */
+ uint8_t tc_bws[ETH_DCB_NUM_TCS]; /**< TX BW percentage for each TC */
+ /** rx queues assigned to tc */
+ struct rte_eth_dcb_tc_queue_mapping tc_queue;
};
-/**
- * A structure used to define a 5tuple filter.
- */
-struct rte_5tuple_filter {
- uint32_t dst_ip; /**< destination IP address in big endian. */
- uint32_t src_ip; /**< source IP address in big endian. */
- uint16_t dst_port; /**< destination port in big endian. */
- uint16_t src_port; /**< source Port big endian. */
- uint8_t protocol; /**< l4 protocol. */
- uint8_t tcp_flags; /**< tcp flags. */
- uint16_t priority; /**< seven evels (001b-111b), 111b is highest,
- used when more than one filter matches. */
- uint8_t dst_ip_mask:1, /**< if mask is 1b, do not compare dst ip. */
- src_ip_mask:1, /**< if mask is 1b, do not compare src ip. */
- dst_port_mask:1, /**< if mask is 1b, do not compare dst port. */
- src_port_mask:1, /**< if mask is 1b, do not compare src port. */
- protocol_mask:1; /**< if mask is 1b, do not compare protocol. */
-};
+struct rte_eth_dev;
+
+struct rte_eth_dev_callback;
+/** @internal Structure to keep track of registered callbacks */
+TAILQ_HEAD(rte_eth_dev_cb_list, rte_eth_dev_callback);
/*
* Definitions of all functions exported by an Ethernet driver through the
typedef void (*eth_stats_reset_t)(struct rte_eth_dev *dev);
/**< @internal Reset global I/O statistics of an Ethernet device to 0. */
+typedef int (*eth_xstats_get_t)(struct rte_eth_dev *dev,
+ struct rte_eth_xstats *stats, unsigned n);
+/**< @internal Get extended stats of an Ethernet device. */
+
+typedef void (*eth_xstats_reset_t)(struct rte_eth_dev *dev);
+/**< @internal Reset extended stats of an Ethernet device. */
+
typedef int (*eth_queue_stats_mapping_set_t)(struct rte_eth_dev *dev,
uint16_t queue_id,
uint8_t stat_idx,
const struct rte_eth_txconf *tx_conf);
/**< @internal Setup a transmit queue of an Ethernet device. */
+typedef int (*eth_rx_enable_intr_t)(struct rte_eth_dev *dev,
+ uint16_t rx_queue_id);
+/**< @internal Enable interrupt of a receive queue of an Ethernet device. */
+
+typedef int (*eth_rx_disable_intr_t)(struct rte_eth_dev *dev,
+ uint16_t rx_queue_id);
+/**< @internal Disable interrupt of a receive queue of an Ethernet device. */
+
typedef void (*eth_queue_release_t)(void *queue);
/**< @internal Release memory resources allocated by given RX/TX queue. */
typedef uint32_t (*eth_rx_queue_count_t)(struct rte_eth_dev *dev,
uint16_t rx_queue_id);
-/**< @Get number of available descriptors on a receive queue of an Ethernet device. */
+/**< @internal Get number of available descriptors on a receive queue of an Ethernet device. */
typedef int (*eth_rx_descriptor_done_t)(void *rxq, uint16_t offset);
-/**< @Check DD bit of specific RX descriptor */
+/**< @internal Check DD bit of specific RX descriptor */
+
+typedef int (*mtu_set_t)(struct rte_eth_dev *dev, uint16_t mtu);
+/**< @internal Set MTU. */
typedef int (*vlan_filter_set_t)(struct rte_eth_dev *dev,
uint16_t vlan_id,
uint16_t nb_pkts);
/**< @internal Send output packets on a transmit queue of an Ethernet device. */
-typedef int (*fdir_add_signature_filter_t)(struct rte_eth_dev *dev,
- struct rte_fdir_filter *fdir_ftr,
- uint8_t rx_queue);
-/**< @internal Setup a new signature filter rule on an Ethernet device */
-
-typedef int (*fdir_update_signature_filter_t)(struct rte_eth_dev *dev,
- struct rte_fdir_filter *fdir_ftr,
- uint8_t rx_queue);
-/**< @internal Update a signature filter rule on an Ethernet device */
-
-typedef int (*fdir_remove_signature_filter_t)(struct rte_eth_dev *dev,
- struct rte_fdir_filter *fdir_ftr);
-/**< @internal Remove a signature filter rule on an Ethernet device */
-
-typedef void (*fdir_infos_get_t)(struct rte_eth_dev *dev,
- struct rte_eth_fdir *fdir);
-/**< @internal Get information about fdir status */
-
-typedef int (*fdir_add_perfect_filter_t)(struct rte_eth_dev *dev,
- struct rte_fdir_filter *fdir_ftr,
- uint16_t soft_id, uint8_t rx_queue,
- uint8_t drop);
-/**< @internal Setup a new perfect filter rule on an Ethernet device */
-
-typedef int (*fdir_update_perfect_filter_t)(struct rte_eth_dev *dev,
- struct rte_fdir_filter *fdir_ftr,
- uint16_t soft_id, uint8_t rx_queue,
- uint8_t drop);
-/**< @internal Update a perfect filter rule on an Ethernet device */
-
-typedef int (*fdir_remove_perfect_filter_t)(struct rte_eth_dev *dev,
- struct rte_fdir_filter *fdir_ftr,
- uint16_t soft_id);
-/**< @internal Remove a perfect filter rule on an Ethernet device */
-
-typedef int (*fdir_set_masks_t)(struct rte_eth_dev *dev,
- struct rte_fdir_masks *fdir_masks);
-/**< @internal Setup flow director masks on an Ethernet device */
-
typedef int (*flow_ctrl_get_t)(struct rte_eth_dev *dev,
struct rte_eth_fc_conf *fc_conf);
/**< @internal Get current flow control parameter on an Ethernet device */
/**< @internal Setup priority flow control parameter on an Ethernet device */
typedef int (*reta_update_t)(struct rte_eth_dev *dev,
- struct rte_eth_rss_reta *reta_conf);
+ struct rte_eth_rss_reta_entry64 *reta_conf,
+ uint16_t reta_size);
/**< @internal Update RSS redirection table on an Ethernet device */
typedef int (*reta_query_t)(struct rte_eth_dev *dev,
- struct rte_eth_rss_reta *reta_conf);
+ struct rte_eth_rss_reta_entry64 *reta_conf,
+ uint16_t reta_size);
/**< @internal Query RSS redirection table on an Ethernet device */
typedef int (*rss_hash_update_t)(struct rte_eth_dev *dev,
uint32_t vmdq);
/**< @internal Set a MAC address into Receive Address Address Register */
+typedef void (*eth_mac_addr_set_t)(struct rte_eth_dev *dev,
+ struct ether_addr *mac_addr);
+/**< @internal Set a MAC address into Receive Address Address Register */
+
typedef int (*eth_uc_hash_table_set_t)(struct rte_eth_dev *dev,
struct ether_addr *mac_addr,
uint8_t on);
/**< @internal Set VF TX rate */
typedef int (*eth_mirror_rule_set_t)(struct rte_eth_dev *dev,
- struct rte_eth_vmdq_mirror_conf *mirror_conf,
+ struct rte_eth_mirror_conf *mirror_conf,
uint8_t rule_id,
uint8_t on);
/**< @internal Add a traffic mirroring rule on an Ethernet device */
uint8_t rule_id);
/**< @internal Remove a traffic mirroring rule on an Ethernet device */
+typedef int (*eth_udp_tunnel_add_t)(struct rte_eth_dev *dev,
+ struct rte_eth_udp_tunnel *tunnel_udp);
+/**< @internal Add tunneling UDP info */
+
+typedef int (*eth_udp_tunnel_del_t)(struct rte_eth_dev *dev,
+ struct rte_eth_udp_tunnel *tunnel_udp);
+/**< @internal Delete tunneling UDP info */
+
+typedef int (*eth_set_mc_addr_list_t)(struct rte_eth_dev *dev,
+ struct ether_addr *mc_addr_set,
+ uint32_t nb_mc_addr);
+/**< @internal set the list of multicast addresses on an Ethernet device */
+
+typedef int (*eth_timesync_enable_t)(struct rte_eth_dev *dev);
+/**< @internal Function used to enable IEEE1588/802.1AS timestamping. */
+
+typedef int (*eth_timesync_disable_t)(struct rte_eth_dev *dev);
+/**< @internal Function used to disable IEEE1588/802.1AS timestamping. */
+
+typedef int (*eth_timesync_read_rx_timestamp_t)(struct rte_eth_dev *dev,
+ struct timespec *timestamp,
+ uint32_t flags);
+/**< @internal Function used to read an RX IEEE1588/802.1AS timestamp. */
+
+typedef int (*eth_timesync_read_tx_timestamp_t)(struct rte_eth_dev *dev,
+ struct timespec *timestamp);
+/**< @internal Function used to read a TX IEEE1588/802.1AS timestamp. */
+
+typedef int (*eth_get_reg_length_t)(struct rte_eth_dev *dev);
+/**< @internal Retrieve device register count */
+
+typedef int (*eth_get_reg_t)(struct rte_eth_dev *dev,
+ struct rte_dev_reg_info *info);
+/**< @internal Retrieve registers */
+
+typedef int (*eth_get_eeprom_length_t)(struct rte_eth_dev *dev);
+/**< @internal Retrieve eeprom size */
+
+typedef int (*eth_get_eeprom_t)(struct rte_eth_dev *dev,
+ struct rte_dev_eeprom_info *info);
+/**< @internal Retrieve eeprom data */
+
+typedef int (*eth_set_eeprom_t)(struct rte_eth_dev *dev,
+ struct rte_dev_eeprom_info *info);
+/**< @internal Program eeprom data */
+
#ifdef RTE_NIC_BYPASS
enum {
typedef int32_t (*bypass_wd_reset_t)(struct rte_eth_dev *dev);
#endif
-typedef int (*eth_add_syn_filter_t)(struct rte_eth_dev *dev,
- struct rte_syn_filter *filter, uint16_t rx_queue);
-/**< @internal add syn filter rule on an Ethernet device */
-
-typedef int (*eth_remove_syn_filter_t)(struct rte_eth_dev *dev);
-/**< @internal remove syn filter rule on an Ethernet device */
-
-typedef int (*eth_get_syn_filter_t)(struct rte_eth_dev *dev,
- struct rte_syn_filter *filter, uint16_t *rx_queue);
-/**< @internal Get syn filter rule on an Ethernet device */
-
-typedef int (*eth_add_ethertype_filter_t)(struct rte_eth_dev *dev,
- uint16_t index, struct rte_ethertype_filter *filter,
- uint16_t rx_queue);
-/**< @internal Setup a new ethertype filter rule on an Ethernet device */
-
-typedef int (*eth_remove_ethertype_filter_t)(struct rte_eth_dev *dev,
- uint16_t index);
-/**< @internal Remove an ethertype filter rule on an Ethernet device */
-
-typedef int (*eth_get_ethertype_filter_t)(struct rte_eth_dev *dev,
- uint16_t index, struct rte_ethertype_filter *filter,
- uint16_t *rx_queue);
-/**< @internal Get an ethertype filter rule on an Ethernet device */
-
-typedef int (*eth_add_2tuple_filter_t)(struct rte_eth_dev *dev,
- uint16_t index, struct rte_2tuple_filter *filter,
- uint16_t rx_queue);
-/**< @internal Setup a new 2tuple filter rule on an Ethernet device */
+typedef int (*eth_filter_ctrl_t)(struct rte_eth_dev *dev,
+ enum rte_filter_type filter_type,
+ enum rte_filter_op filter_op,
+ void *arg);
+/**< @internal Take operations to assigned filter type on an Ethernet device */
-typedef int (*eth_remove_2tuple_filter_t)(struct rte_eth_dev *dev,
- uint16_t index);
-/**< @internal Remove a 2tuple filter rule on an Ethernet device */
-
-typedef int (*eth_get_2tuple_filter_t)(struct rte_eth_dev *dev,
- uint16_t index, struct rte_2tuple_filter *filter,
- uint16_t *rx_queue);
-/**< @internal Get a 2tuple filter rule on an Ethernet device */
-
-typedef int (*eth_add_5tuple_filter_t)(struct rte_eth_dev *dev,
- uint16_t index, struct rte_5tuple_filter *filter,
- uint16_t rx_queue);
-/**< @internal Setup a new 5tuple filter rule on an Ethernet device */
-
-typedef int (*eth_remove_5tuple_filter_t)(struct rte_eth_dev *dev,
- uint16_t index);
-/**< @internal Remove a 5tuple filter rule on an Ethernet device */
-
-typedef int (*eth_get_5tuple_filter_t)(struct rte_eth_dev *dev,
- uint16_t index, struct rte_5tuple_filter *filter,
- uint16_t *rx_queue);
-/**< @internal Get a 5tuple filter rule on an Ethernet device */
-
-typedef int (*eth_add_flex_filter_t)(struct rte_eth_dev *dev,
- uint16_t index, struct rte_flex_filter *filter,
- uint16_t rx_queue);
-/**< @internal Setup a new flex filter rule on an Ethernet device */
-
-typedef int (*eth_remove_flex_filter_t)(struct rte_eth_dev *dev,
- uint16_t index);
-/**< @internal Remove a flex filter rule on an Ethernet device */
-
-typedef int (*eth_get_flex_filter_t)(struct rte_eth_dev *dev,
- uint16_t index, struct rte_flex_filter *filter,
- uint16_t *rx_queue);
-/**< @internal Get a flex filter rule on an Ethernet device */
+typedef int (*eth_get_dcb_info)(struct rte_eth_dev *dev,
+ struct rte_eth_dcb_info *dcb_info);
+/**< @internal Get dcb information on an Ethernet device */
/**
* @internal A structure containing the functions exported by an Ethernet driver.
eth_allmulticast_enable_t allmulticast_enable;/**< RX multicast ON. */
eth_allmulticast_disable_t allmulticast_disable;/**< RX multicast OF. */
eth_link_update_t link_update; /**< Get device link state. */
- eth_stats_get_t stats_get; /**< Get device statistics. */
- eth_stats_reset_t stats_reset; /**< Reset device statistics. */
+ eth_stats_get_t stats_get; /**< Get generic device statistics. */
+ eth_stats_reset_t stats_reset; /**< Reset generic device statistics. */
+ eth_xstats_get_t xstats_get; /**< Get extended device statistics. */
+ eth_xstats_reset_t xstats_reset; /**< Reset extended device statistics. */
eth_queue_stats_mapping_set_t queue_stats_mapping_set;
/**< Configure per queue stat counter mapping. */
eth_dev_infos_get_t dev_infos_get; /**< Get device info. */
+ mtu_set_t mtu_set; /**< Set MTU. */
vlan_filter_set_t vlan_filter_set; /**< Filter VLAN Setup. */
vlan_tpid_set_t vlan_tpid_set; /**< Outer VLAN TPID Setup. */
vlan_strip_queue_set_t vlan_strip_queue_set; /**< VLAN Stripping on queue. */
eth_queue_release_t rx_queue_release;/**< Release RX queue.*/
eth_rx_queue_count_t rx_queue_count; /**< Get Rx queue count. */
eth_rx_descriptor_done_t rx_descriptor_done; /**< Check rxd DD bit */
+ /**< Enable Rx queue interrupt. */
+ eth_rx_enable_intr_t rx_queue_intr_enable;
+ /**< Disable Rx queue interrupt.*/
+ eth_rx_disable_intr_t rx_queue_intr_disable;
eth_tx_queue_setup_t tx_queue_setup;/**< Set up device TX queue.*/
eth_queue_release_t tx_queue_release;/**< Release TX queue.*/
eth_dev_led_on_t dev_led_on; /**< Turn on LED. */
priority_flow_ctrl_set_t priority_flow_ctrl_set; /**< Setup priority flow control.*/
eth_mac_addr_remove_t mac_addr_remove; /**< Remove MAC address */
eth_mac_addr_add_t mac_addr_add; /**< Add a MAC address */
+ eth_mac_addr_set_t mac_addr_set; /**< Set a MAC address */
eth_uc_hash_table_set_t uc_hash_table_set; /**< Set Unicast Table Array */
eth_uc_all_hash_table_set_t uc_all_hash_table_set; /**< Set Unicast hash bitmap */
eth_mirror_rule_set_t mirror_rule_set; /**< Add a traffic mirror rule.*/
eth_set_vf_rx_t set_vf_rx; /**< enable/disable a VF receive */
eth_set_vf_tx_t set_vf_tx; /**< enable/disable a VF transmit */
eth_set_vf_vlan_filter_t set_vf_vlan_filter; /**< Set VF VLAN filter */
+ eth_udp_tunnel_add_t udp_tunnel_add;
+ eth_udp_tunnel_del_t udp_tunnel_del;
eth_set_queue_rate_limit_t set_queue_rate_limit; /**< Set queue rate limit */
eth_set_vf_rate_limit_t set_vf_rate_limit; /**< Set VF rate limit */
-
- /** Add a signature filter. */
- fdir_add_signature_filter_t fdir_add_signature_filter;
- /** Update a signature filter. */
- fdir_update_signature_filter_t fdir_update_signature_filter;
- /** Remove a signature filter. */
- fdir_remove_signature_filter_t fdir_remove_signature_filter;
- /** Get information about FDIR status. */
- fdir_infos_get_t fdir_infos_get;
- /** Add a perfect filter. */
- fdir_add_perfect_filter_t fdir_add_perfect_filter;
- /** Update a perfect filter. */
- fdir_update_perfect_filter_t fdir_update_perfect_filter;
- /** Remove a perfect filter. */
- fdir_remove_perfect_filter_t fdir_remove_perfect_filter;
- /** Setup masks for FDIR filtering. */
- fdir_set_masks_t fdir_set_masks;
/** Update redirection table. */
reta_update_t reta_update;
/** Query redirection table. */
reta_query_t reta_query;
+
+ eth_get_reg_length_t get_reg_length;
+ /**< Get # of registers */
+ eth_get_reg_t get_reg;
+ /**< Get registers */
+ eth_get_eeprom_length_t get_eeprom_length;
+ /**< Get eeprom length */
+ eth_get_eeprom_t get_eeprom;
+ /**< Get eeprom data */
+ eth_set_eeprom_t set_eeprom;
+ /**< Set eeprom */
/* bypass control */
#ifdef RTE_NIC_BYPASS
bypass_init_t bypass_init;
rss_hash_update_t rss_hash_update;
/** Get current RSS hash configuration. */
rss_hash_conf_get_t rss_hash_conf_get;
- eth_add_syn_filter_t add_syn_filter; /**< add syn filter. */
- eth_remove_syn_filter_t remove_syn_filter; /**< remove syn filter. */
- eth_get_syn_filter_t get_syn_filter; /**< get syn filter. */
- eth_add_ethertype_filter_t add_ethertype_filter; /**< add ethertype filter. */
- eth_remove_ethertype_filter_t remove_ethertype_filter; /**< remove ethertype filter. */
- eth_get_ethertype_filter_t get_ethertype_filter; /**< get ethertype filter. */
- eth_add_2tuple_filter_t add_2tuple_filter; /**< add 2tuple filter. */
- eth_remove_2tuple_filter_t remove_2tuple_filter; /**< remove 2tuple filter. */
- eth_get_2tuple_filter_t get_2tuple_filter; /**< get 2tuple filter. */
- eth_add_5tuple_filter_t add_5tuple_filter; /**< add 5tuple filter. */
- eth_remove_5tuple_filter_t remove_5tuple_filter; /**< remove 5tuple filter. */
- eth_get_5tuple_filter_t get_5tuple_filter; /**< get 5tuple filter. */
- eth_add_flex_filter_t add_flex_filter; /**< add flex filter. */
- eth_remove_flex_filter_t remove_flex_filter; /**< remove flex filter. */
- eth_get_flex_filter_t get_flex_filter; /**< get flex filter. */
+ eth_filter_ctrl_t filter_ctrl; /**< common filter control*/
+ eth_set_mc_addr_list_t set_mc_addr_list; /**< set list of mcast addrs */
+
+ /** Turn IEEE1588/802.1AS timestamping on. */
+ eth_timesync_enable_t timesync_enable;
+ /** Turn IEEE1588/802.1AS timestamping off. */
+ eth_timesync_disable_t timesync_disable;
+ /** Read the IEEE1588/802.1AS RX timestamp. */
+ eth_timesync_read_rx_timestamp_t timesync_read_rx_timestamp;
+ /** Read the IEEE1588/802.1AS TX timestamp. */
+ eth_timesync_read_tx_timestamp_t timesync_read_tx_timestamp;
+
+ /** Get DCB information */
+ eth_get_dcb_info get_dcb_info;
+};
+
+/**
+ * Function type used for RX packet processing packet callbacks.
+ *
+ * The callback function is called on RX with a burst of packets that have
+ * been received on the given port and queue.
+ *
+ * @param port
+ * The Ethernet port on which RX is being performed.
+ * @param queue
+ * The queue on the Ethernet port which is being used to receive the packets.
+ * @param pkts
+ * The burst of packets that have just been received.
+ * @param nb_pkts
+ * The number of packets in the burst pointed to by "pkts".
+ * @param max_pkts
+ * The max number of packets that can be stored in the "pkts" array.
+ * @param user_param
+ * The arbitrary user parameter passed in by the application when the callback
+ * was originally configured.
+ * @return
+ * The number of packets returned to the user.
+ */
+typedef uint16_t (*rte_rx_callback_fn)(uint8_t port, uint16_t queue,
+ struct rte_mbuf *pkts[], uint16_t nb_pkts, uint16_t max_pkts,
+ void *user_param);
+
+/**
+ * Function type used for TX packet processing packet callbacks.
+ *
+ * The callback function is called on TX with a burst of packets immediately
+ * before the packets are put onto the hardware queue for transmission.
+ *
+ * @param port
+ * The Ethernet port on which TX is being performed.
+ * @param queue
+ * The queue on the Ethernet port which is being used to transmit the packets.
+ * @param pkts
+ * The burst of packets that are about to be transmitted.
+ * @param nb_pkts
+ * The number of packets in the burst pointed to by "pkts".
+ * @param user_param
+ * The arbitrary user parameter passed in by the application when the callback
+ * was originally configured.
+ * @return
+ * The number of packets to be written to the NIC.
+ */
+typedef uint16_t (*rte_tx_callback_fn)(uint8_t port, uint16_t queue,
+ struct rte_mbuf *pkts[], uint16_t nb_pkts, void *user_param);
+
+/**
+ * @internal
+ * Structure used to hold information about the callbacks to be called for a
+ * queue on RX and TX.
+ */
+struct rte_eth_rxtx_callback {
+ struct rte_eth_rxtx_callback *next;
+ union{
+ rte_rx_callback_fn rx;
+ rte_tx_callback_fn tx;
+ } fn;
+ void *param;
+};
+
+/**
+ * The eth device type.
+ */
+enum rte_eth_dev_type {
+ RTE_ETH_DEV_UNKNOWN, /**< unknown device type */
+ RTE_ETH_DEV_PCI,
+ /**< Physical function and Virtual function of PCI devices */
+ RTE_ETH_DEV_VIRTUAL, /**< non hardware device */
+ RTE_ETH_DEV_MAX /**< max value of this enum */
};
/**
eth_tx_burst_t tx_pkt_burst; /**< Pointer to PMD transmit function. */
struct rte_eth_dev_data *data; /**< Pointer to device data */
const struct eth_driver *driver;/**< Driver for this device */
- struct eth_dev_ops *dev_ops; /**< Functions exported by PMD */
+ const struct eth_dev_ops *dev_ops; /**< Functions exported by PMD */
struct rte_pci_device *pci_dev; /**< PCI info. supplied by probing */
- struct rte_eth_dev_cb_list callbacks; /**< User application callbacks */
+ /** User application callbacks for NIC interrupts */
+ struct rte_eth_dev_cb_list link_intr_cbs;
+ /**
+ * User-supplied functions called from rx_burst to post-process
+ * received packets before passing them to the user
+ */
+ struct rte_eth_rxtx_callback *post_rx_burst_cbs[RTE_MAX_QUEUES_PER_PORT];
+ /**
+ * User-supplied functions called from tx_burst to pre-process
+ * received packets before passing them to the driver for transmission.
+ */
+ struct rte_eth_rxtx_callback *pre_tx_burst_cbs[RTE_MAX_QUEUES_PER_PORT];
+ uint8_t attached; /**< Flag indicating the port is attached */
+ enum rte_eth_dev_type dev_type; /**< Flag indicating the device type */
};
struct rte_eth_dev_sriov {
};
#define RTE_ETH_DEV_SRIOV(dev) ((dev)->data->sriov)
+#define RTE_ETH_NAME_MAX_LEN (32)
+
/**
* @internal
* The data part, with no function pointers, associated with each ethernet device.
* processes in a multi-process configuration.
*/
struct rte_eth_dev_data {
+ char name[RTE_ETH_NAME_MAX_LEN]; /**< Unique identifier name */
+
void **rx_queues; /**< Array of pointers to RX queues. */
void **tx_queues; /**< Array of pointers to TX queues. */
uint16_t nb_rx_queues; /**< Number of RX queues. */
/**< Link-level information & status */
struct rte_eth_conf dev_conf; /**< Configuration applied to device. */
- uint16_t max_frame_size; /**< Default is ETHER_MAX_LEN (1518). */
+ uint16_t mtu; /**< Maximum Transmission Unit. */
uint32_t min_rx_buf_size;
/**< Common rx buffer size handled by all queues */
uint8_t promiscuous : 1, /**< RX promiscuous mode ON(1) / OFF(0). */
scattered_rx : 1, /**< RX of scattered packets is ON(1) / OFF(0) */
all_multicast : 1, /**< RX all multicast mode ON(1) / OFF(0). */
- dev_started : 1; /**< Device state: STARTED(1) / STOPPED(0). */
+ dev_started : 1, /**< Device state: STARTED(1) / STOPPED(0). */
+ lro : 1; /**< RX LRO is ON(1) / OFF(0) */
};
/**
* Get the total number of Ethernet devices that have been successfully
* initialized by the [matching] Ethernet driver during the PCI probing phase.
* All devices whose port identifier is in the range
- * [0, rte_eth_dev_count() - 1] can be operated on by network applications.
+ * [0, rte_eth_dev_count() - 1] can be operated on by network applications
+ * immediately after invoking rte_eal_init().
+ * If the application unplugs a port using hotplug function, The enabled port
+ * numbers may be noncontiguous. In the case, the applications need to manage
+ * enabled port by themselves.
*
* @return
* - The total number of usable Ethernet devices.
extern uint8_t rte_eth_dev_count(void);
/**
- * Function for internal use by dummy drivers primarily, e.g. ring-based
- * driver.
+ * @internal
+ * Returns a ethdev slot specified by the unique identifier name.
+ *
+ * @param name
+ * The pointer to the Unique identifier name for each Ethernet device
+ * @return
+ * - The pointer to the ethdev slot, on success. NULL on error
+ */
+extern struct rte_eth_dev *rte_eth_dev_allocated(const char *name);
+
+/**
+ * @internal
* Allocates a new ethdev slot for an ethernet device and returns the pointer
* to that slot for the driver to use.
*
+ * @param name Unique identifier name for each Ethernet device
+ * @param type Device type of this Ethernet device
* @return
* - Slot in the rte_dev_devices array for a new device;
*/
-struct rte_eth_dev *rte_eth_dev_allocate(void);
+struct rte_eth_dev *rte_eth_dev_allocate(const char *name,
+ enum rte_eth_dev_type type);
+
+/**
+ * @internal
+ * Release the specified ethdev port.
+ *
+ * @param eth_dev
+ * The *eth_dev* pointer is the address of the *rte_eth_dev* structure.
+ * @return
+ * - 0 on success, negative on error
+ */
+int rte_eth_dev_release_port(struct rte_eth_dev *eth_dev);
+
+/**
+ * Attach a new Ethernet device specified by aruguments.
+ *
+ * @param devargs
+ * A pointer to a strings array describing the new device
+ * to be attached. The strings should be a pci address like
+ * '0000:01:00.0' or virtual device name like 'eth_pcap0'.
+ * @param port_id
+ * A pointer to a port identifier actually attached.
+ * @return
+ * 0 on success and port_id is filled, negative on error
+ */
+int rte_eth_dev_attach(const char *devargs, uint8_t *port_id);
+
+/**
+ * Detach a Ethernet device specified by port identifier.
+ * This function must be called when the device is in the
+ * closed state.
+ *
+ * @param port_id
+ * The port identifier of the device to detach.
+ * @param devname
+ * A pointer to a device name actually detached.
+ * @return
+ * 0 on success and devname is filled, negative on error
+ */
+int rte_eth_dev_detach(uint8_t port_id, char *devname);
struct eth_driver;
/**
* Initialization function of an Ethernet driver invoked for each matching
* Ethernet PCI device detected during the PCI probing phase.
*
- * @param eth_drv
- * The pointer to the [matching] Ethernet driver structure supplied by
- * the PMD when it registered itself.
* @param eth_dev
* The *eth_dev* pointer is the address of the *rte_eth_dev* structure
* associated with the matching device and which have been [automatically]
* - *pci_dev*: Holds the pointers to the *rte_pci_device* structure which
* contains the generic PCI information of the matching device.
*
+ * - *driver*: Holds the pointer to the *eth_driver* structure.
+ *
* - *dev_private*: Holds a pointer to the device private data structure.
*
- * - *max_frame_size*: Contains the default Ethernet maximum frame length
- * (1518).
+ * - *mtu*: Contains the default Ethernet maximum frame length (1500).
*
* - *port_id*: Contains the port index of the device (actually the index
* of the *eth_dev* structure in the *rte_eth_devices* array).
* of the *eth_dev* structure.
* - <0: Error code of the device initialization failure.
*/
-typedef int (*eth_dev_init_t)(struct eth_driver *eth_drv,
- struct rte_eth_dev *eth_dev);
+typedef int (*eth_dev_init_t)(struct rte_eth_dev *eth_dev);
+
+/**
+ * @internal
+ * Finalization function of an Ethernet driver invoked for each matching
+ * Ethernet PCI device detected during the PCI closing phase.
+ *
+ * @param eth_dev
+ * The *eth_dev* pointer is the address of the *rte_eth_dev* structure
+ * associated with the matching device and which have been [automatically]
+ * allocated in the *rte_eth_devices* array.
+ * @return
+ * - 0: Success, the device is properly finalized by the driver.
+ * In particular, the driver MUST free the *dev_ops* pointer
+ * of the *eth_dev* structure.
+ * - <0: Error code of the device initialization failure.
+ */
+typedef int (*eth_dev_uninit_t)(struct rte_eth_dev *eth_dev);
/**
* @internal
*
* - The *eth_dev_init* function invoked for each matching PCI device.
*
+ * - The *eth_dev_uninit* function invoked for each matching PCI device.
+ *
* - The size of the private data to allocate for each matching device.
*/
struct eth_driver {
struct rte_pci_driver pci_drv; /**< The PMD is also a PCI driver. */
eth_dev_init_t eth_dev_init; /**< Device init function. */
+ eth_dev_uninit_t eth_dev_uninit; /**< Device uninit function. */
unsigned int dev_private_size; /**< Size of device private data. */
};
* the DMA memory allocated for the receive descriptors of the ring.
* @param rx_conf
* The pointer to the configuration data to be used for the receive queue.
+ * NULL value is allowed, in which case default RX configuration
+ * will be used.
* The *rx_conf* structure contains an *rx_thresh* structure with the values
* of the Prefetch, Host, and Write-Back threshold registers of the receive
* ring.
* the DMA memory allocated for the transmit descriptors of the ring.
* @param tx_conf
* The pointer to the configuration data to be used for the transmit queue.
+ * NULL value is allowed, in which case default RX configuration
+ * will be used.
* The *tx_conf* structure contains the following data:
* - The *tx_thresh* structure with the values of the Prefetch, Host, and
* Write-Back threshold registers of the transmit ring.
extern int rte_eth_dev_socket_id(uint8_t port_id);
/*
- * Start specified RX queue of a port
+ * Check if port_id of device is attached
+ *
+ * @param port_id
+ * The port identifier of the Ethernet device
+ * @return
+ * - 0 if port is out of range or not attached
+ * - 1 if device is attached
+ */
+extern int rte_eth_dev_is_valid_port(uint8_t port_id);
+
+/*
+ * Allocate mbuf from mempool, setup the DMA physical address
+ * and then start RX for specified queue of a port. It is used
+ * when rx_deferred_start flag of the specified queue is true.
*
* @param port_id
* The port identifier of the Ethernet device
extern int rte_eth_dev_rx_queue_stop(uint8_t port_id, uint16_t rx_queue_id);
/*
- * Start specified TX queue of a port
+ * Start TX for specified queue of a port. It is used when tx_deferred_start
+ * flag of the specified queue is true.
*
* @param port_id
* The port identifier of the Ethernet device
extern int rte_eth_dev_set_link_down(uint8_t port_id);
/**
- * Close an Ethernet device. The device cannot be restarted!
+ * Close a stopped Ethernet device. The device cannot be restarted!
+ * The function frees all resources except for needed by the
+ * closed state. To free these resources, call rte_eth_dev_detach().
*
* @param port_id
* The port identifier of the Ethernet device.
* - *obytes* with the total of successfully transmitted bytes.
* - *ierrors* with the total of erroneous received packets.
* - *oerrors* with the total of failed transmitted packets.
+ * @return
+ * Zero if successful. Non-zero otherwise.
*/
-extern void rte_eth_stats_get(uint8_t port_id, struct rte_eth_stats *stats);
+extern int rte_eth_stats_get(uint8_t port_id, struct rte_eth_stats *stats);
/**
* Reset the general I/O statistics of an Ethernet device.
*/
extern void rte_eth_stats_reset(uint8_t port_id);
+/**
+ * Retrieve extended statistics of an Ethernet device.
+ *
+ * @param port_id
+ * The port identifier of the Ethernet device.
+ * @param xstats
+ * A pointer to a table of structure of type *rte_eth_xstats*
+ * to be filled with device statistics names and values.
+ * This parameter can be set to NULL if n is 0.
+ * @param n
+ * The size of the stats table, which should be large enough to store
+ * all the statistics of the device.
+ * @return
+ * - positive value lower or equal to n: success. The return value
+ * is the number of entries filled in the stats table.
+ * - positive value higher than n: error, the given statistics table
+ * is too small. The return value corresponds to the size that should
+ * be given to succeed. The entries in the table are not valid and
+ * shall not be used by the caller.
+ * - negative value on error (invalid port id)
+ */
+extern int rte_eth_xstats_get(uint8_t port_id,
+ struct rte_eth_xstats *xstats, unsigned n);
+
+/**
+ * Reset extended statistics of an Ethernet device.
+ *
+ * @param port_id
+ * The port identifier of the Ethernet device.
+ */
+extern void rte_eth_xstats_reset(uint8_t port_id);
+
/**
* Set a mapping for the specified transmit queue to the specified per-queue
* statistics counter.
extern void rte_eth_dev_info_get(uint8_t port_id,
struct rte_eth_dev_info *dev_info);
+/**
+ * Retrieve the MTU of an Ethernet device.
+ *
+ * @param port_id
+ * The port identifier of the Ethernet device.
+ * @param mtu
+ * A pointer to a uint16_t where the retrieved MTU is to be stored.
+ * @return
+ * - (0) if successful.
+ * - (-ENODEV) if *port_id* invalid.
+ */
+extern int rte_eth_dev_get_mtu(uint8_t port_id, uint16_t *mtu);
+
+/**
+ * Change the MTU of an Ethernet device.
+ *
+ * @param port_id
+ * The port identifier of the Ethernet device.
+ * @param mtu
+ * A uint16_t for the MTU to be applied.
+ * @return
+ * - (0) if successful.
+ * - (-ENOTSUP) if operation is not supported.
+ * - (-ENODEV) if *port_id* invalid.
+ * - (-EINVAL) if *mtu* invalid.
+ */
+extern int rte_eth_dev_set_mtu(uint8_t port_id, uint16_t mtu);
+
/**
* Enable/Disable hardware filtering by an Ethernet device of received
* VLAN packets tagged with a given VLAN Tag Identifier.
/**
* Enable/Disable hardware VLAN Strip by a rx queue of an Ethernet device.
- * 82599/X540 can support VLAN stripping at the rx queue level
+ * 82599/X540/X550 can support VLAN stripping at the rx queue level
*
* @param port_id
* The port identifier of the Ethernet device.
#else
static inline uint16_t
rte_eth_rx_burst(uint8_t port_id, uint16_t queue_id,
- struct rte_mbuf **rx_pkts, uint16_t nb_pkts)
+ struct rte_mbuf **rx_pkts, const uint16_t nb_pkts)
{
struct rte_eth_dev *dev;
dev = &rte_eth_devices[port_id];
- return (*dev->rx_pkt_burst)(dev->data->rx_queues[queue_id], rx_pkts, nb_pkts);
+
+ int16_t nb_rx = (*dev->rx_pkt_burst)(dev->data->rx_queues[queue_id],
+ rx_pkts, nb_pkts);
+
+#ifdef RTE_ETHDEV_RXTX_CALLBACKS
+ struct rte_eth_rxtx_callback *cb = dev->post_rx_burst_cbs[queue_id];
+
+ if (unlikely(cb != NULL)) {
+ do {
+ nb_rx = cb->fn.rx(port_id, queue_id, rx_pkts, nb_rx,
+ nb_pkts, cb->param);
+ cb = cb->next;
+ } while (cb != NULL);
+ }
+#endif
+
+ return nb_rx;
}
#endif
* The port identifier of the Ethernet device.
* @param queue_id
* The queue id on the specific port.
- * @offset
+ * @param offset
* The offset of the descriptor ID from tail.
* @return
* - (1) if the specific DD bit is set.
* transparently free the memory buffers of packets previously sent.
* This feature is driven by the *tx_free_thresh* value supplied to the
* rte_eth_dev_configure() function at device configuration time.
- * When the number of previously sent packets reached the "minimum transmit
- * packets to free" threshold, the rte_eth_tx_burst() function must
- * [attempt to] free the *rte_mbuf* buffers of those packets whose
- * transmission was effectively completed.
+ * When the number of free TX descriptors drops below this threshold, the
+ * rte_eth_tx_burst() function must [attempt to] free the *rte_mbuf* buffers
+ * of those packets whose transmission was effectively completed.
*
* @param port_id
* The port identifier of the Ethernet device.
struct rte_eth_dev *dev;
dev = &rte_eth_devices[port_id];
- return (*dev->tx_pkt_burst)(dev->data->tx_queues[queue_id], tx_pkts, nb_pkts);
-}
-#endif
-/**
- * Setup a new signature filter rule on an Ethernet device
- *
- * @param port_id
- * The port identifier of the Ethernet device.
- * @param fdir_filter
- * The pointer to the fdir filter structure describing the signature filter
- * rule.
- * The *rte_fdir_filter* structure includes the values of the different fields
- * to match: source and destination IP addresses, vlan id, flexbytes, source
- * and destination ports, and so on.
- * @param rx_queue
- * The index of the RX queue where to store RX packets matching the added
- * signature filter defined in fdir_filter.
- * @return
- * - (0) if successful.
- * - (-ENOTSUP) if hardware doesn't support flow director mode.
- * - (-ENODEV) if *port_id* invalid.
- * - (-ENOSYS) if the FDIR mode is not configured in signature mode
- * on *port_id*.
- * - (-EINVAL) if the fdir_filter information is not correct.
- */
-int rte_eth_dev_fdir_add_signature_filter(uint8_t port_id,
- struct rte_fdir_filter *fdir_filter,
- uint8_t rx_queue);
+#ifdef RTE_ETHDEV_RXTX_CALLBACKS
+ struct rte_eth_rxtx_callback *cb = dev->pre_tx_burst_cbs[queue_id];
-/**
- * Update a signature filter rule on an Ethernet device.
- * If the rule doesn't exits, it is created.
- *
- * @param port_id
- * The port identifier of the Ethernet device.
- * @param fdir_ftr
- * The pointer to the structure describing the signature filter rule.
- * The *rte_fdir_filter* structure includes the values of the different fields
- * to match: source and destination IP addresses, vlan id, flexbytes, source
- * and destination ports, and so on.
- * @param rx_queue
- * The index of the RX queue where to store RX packets matching the added
- * signature filter defined in fdir_ftr.
- * @return
- * - (0) if successful.
- * - (-ENOTSUP) if hardware doesn't support flow director mode.
- * - (-ENODEV) if *port_id* invalid.
- * - (-ENOSYS) if the flow director mode is not configured in signature mode
- * on *port_id*.
- * - (-EINVAL) if the fdir_filter information is not correct.
- */
-int rte_eth_dev_fdir_update_signature_filter(uint8_t port_id,
- struct rte_fdir_filter *fdir_ftr,
- uint8_t rx_queue);
-
-/**
- * Remove a signature filter rule on an Ethernet device.
- *
- * @param port_id
- * The port identifier of the Ethernet device.
- * @param fdir_ftr
- * The pointer to the structure describing the signature filter rule.
- * The *rte_fdir_filter* structure includes the values of the different fields
- * to match: source and destination IP addresses, vlan id, flexbytes, source
- * and destination ports, and so on.
- * @return
- * - (0) if successful.
- * - (-ENOTSUP) if hardware doesn't support flow director mode.
- * - (-ENODEV) if *port_id* invalid.
- * - (-ENOSYS) if the flow director mode is not configured in signature mode
- * on *port_id*.
- * - (-EINVAL) if the fdir_filter information is not correct.
- */
-int rte_eth_dev_fdir_remove_signature_filter(uint8_t port_id,
- struct rte_fdir_filter *fdir_ftr);
-
-/**
- * Retrieve the flow director information of an Ethernet device.
- *
- * @param port_id
- * The port identifier of the Ethernet device.
- * @param fdir
- * A pointer to a structure of type *rte_eth_dev_fdir* to be filled with
- * the flow director information of the Ethernet device.
- * @return
- * - (0) if successful.
- * - (-ENOTSUP) if hardware doesn't support flow director mode.
- * - (-ENODEV) if *port_id* invalid.
- * - (-ENOSYS) if the flow director mode is not configured on *port_id*.
- */
-int rte_eth_dev_fdir_get_infos(uint8_t port_id, struct rte_eth_fdir *fdir);
-
-/**
- * Add a new perfect filter rule on an Ethernet device.
- *
- * @param port_id
- * The port identifier of the Ethernet device.
- * @param fdir_filter
- * The pointer to the structure describing the perfect filter rule.
- * The *rte_fdir_filter* structure includes the values of the different fields
- * to match: source and destination IP addresses, vlan id, flexbytes, source
- * and destination ports, and so on.
- * IPv6 are not supported.
- * @param soft_id
- * The 16-bit value supplied in the field hash.fdir.id of mbuf for RX
- * packets matching the perfect filter.
- * @param rx_queue
- * The index of the RX queue where to store RX packets matching the added
- * perfect filter defined in fdir_filter.
- * @param drop
- * If drop is set to 1, matching RX packets are stored into the RX drop
- * queue defined in the rte_fdir_conf.
- * @return
- * - (0) if successful.
- * - (-ENOTSUP) if hardware doesn't support flow director mode.
- * - (-ENODEV) if *port_id* invalid.
- * - (-ENOSYS) if the flow director mode is not configured in perfect mode
- * on *port_id*.
- * - (-EINVAL) if the fdir_filter information is not correct.
- */
-int rte_eth_dev_fdir_add_perfect_filter(uint8_t port_id,
- struct rte_fdir_filter *fdir_filter,
- uint16_t soft_id, uint8_t rx_queue,
- uint8_t drop);
-
-/**
- * Update a perfect filter rule on an Ethernet device.
- * If the rule doesn't exits, it is created.
- *
- * @param port_id
- * The port identifier of the Ethernet device.
- * @param fdir_filter
- * The pointer to the structure describing the perfect filter rule.
- * The *rte_fdir_filter* structure includes the values of the different fields
- * to match: source and destination IP addresses, vlan id, flexbytes, source
- * and destination ports, and so on.
- * IPv6 are not supported.
- * @param soft_id
- * The 16-bit value supplied in the field hash.fdir.id of mbuf for RX
- * packets matching the perfect filter.
- * @param rx_queue
- * The index of the RX queue where to store RX packets matching the added
- * perfect filter defined in fdir_filter.
- * @param drop
- * If drop is set to 1, matching RX packets are stored into the RX drop
- * queue defined in the rte_fdir_conf.
- * @return
- * - (0) if successful.
- * - (-ENOTSUP) if hardware doesn't support flow director mode.
- * - (-ENODEV) if *port_id* invalid.
- * - (-ENOSYS) if the flow director mode is not configured in perfect mode
- * on *port_id*.
- * - (-EINVAL) if the fdir_filter information is not correct.
- */
-int rte_eth_dev_fdir_update_perfect_filter(uint8_t port_id,
- struct rte_fdir_filter *fdir_filter,
- uint16_t soft_id, uint8_t rx_queue,
- uint8_t drop);
+ if (unlikely(cb != NULL)) {
+ do {
+ nb_pkts = cb->fn.tx(port_id, queue_id, tx_pkts, nb_pkts,
+ cb->param);
+ cb = cb->next;
+ } while (cb != NULL);
+ }
+#endif
-/**
- * Remove a perfect filter rule on an Ethernet device.
- *
- * @param port_id
- * The port identifier of the Ethernet device.
- * @param fdir_filter
- * The pointer to the structure describing the perfect filter rule.
- * The *rte_fdir_filter* structure includes the values of the different fields
- * to match: source and destination IP addresses, vlan id, flexbytes, source
- * and destination ports, and so on.
- * IPv6 are not supported.
- * @param soft_id
- * The soft_id value provided when adding/updating the removed filter.
- * @return
- * - (0) if successful.
- * - (-ENOTSUP) if hardware doesn't support flow director mode.
- * - (-ENODEV) if *port_id* invalid.
- * - (-ENOSYS) if the flow director mode is not configured in perfect mode
- * on *port_id*.
- * - (-EINVAL) if the fdir_filter information is not correct.
- */
-int rte_eth_dev_fdir_remove_perfect_filter(uint8_t port_id,
- struct rte_fdir_filter *fdir_filter,
- uint16_t soft_id);
-/**
- * Configure globally the masks for flow director mode for an Ethernet device.
- * For example, the device can match packets with only the first 24 bits of
- * the IPv4 source address.
- *
- * The following fields can be masked: IPv4 addresses and L4 port numbers.
- * The following fields can be either enabled or disabled completely for the
- * matching functionality: VLAN ID tag; VLAN Priority + CFI bit; Flexible 2-byte
- * tuple.
- * IPv6 masks are not supported.
- *
- * All filters must comply with the masks previously configured.
- * For example, with a mask equal to 255.255.255.0 for the source IPv4 address,
- * all IPv4 filters must be created with a source IPv4 address that fits the
- * "X.X.X.0" format.
- *
- * This function flushes all filters that have been previously added in
- * the device.
- *
- * @param port_id
- * The port identifier of the Ethernet device.
- * @param fdir_mask
- * The pointer to the fdir mask structure describing relevant headers fields
- * and relevant bits to use when matching packets addresses and ports.
- * IPv6 masks are not supported.
- * @return
- * - (0) if successful.
- * - (-ENOTSUP) if hardware doesn't support flow director mode.
- * - (-ENODEV) if *port_id* invalid.
- * - (-ENOSYS) if the flow director mode is not configured in perfect
- * mode on *port_id*.
- * - (-EINVAL) if the fdir_filter information is not correct
- */
-int rte_eth_dev_fdir_set_masks(uint8_t port_id,
- struct rte_fdir_masks *fdir_mask);
+ return (*dev->tx_pkt_burst)(dev->data->tx_queues[queue_id], tx_pkts, nb_pkts);
+}
+#endif
/**
* The eth device event type for interrupt, and maybe others in the future.
void _rte_eth_dev_callback_process(struct rte_eth_dev *dev,
enum rte_eth_event_type event);
+/**
+ * When there is no rx packet coming in Rx Queue for a long time, we can
+ * sleep lcore related to RX Queue for power saving, and enable rx interrupt
+ * to be triggered when rx packect arrives.
+ *
+ * The rte_eth_dev_rx_intr_enable() function enables rx queue
+ * interrupt on specific rx queue of a port.
+ *
+ * @param port_id
+ * The port identifier of the Ethernet device.
+ * @param queue_id
+ * The index of the receive queue from which to retrieve input packets.
+ * The value must be in the range [0, nb_rx_queue - 1] previously supplied
+ * to rte_eth_dev_configure().
+ * @return
+ * - (0) if successful.
+ * - (-ENOTSUP) if underlying hardware OR driver doesn't support
+ * that operation.
+ * - (-ENODEV) if *port_id* invalid.
+ */
+int rte_eth_dev_rx_intr_enable(uint8_t port_id, uint16_t queue_id);
+
+/**
+ * When lcore wakes up from rx interrupt indicating packet coming, disable rx
+ * interrupt and returns to polling mode.
+ *
+ * The rte_eth_dev_rx_intr_disable() function disables rx queue
+ * interrupt on specific rx queue of a port.
+ *
+ * @param port_id
+ * The port identifier of the Ethernet device.
+ * @param queue_id
+ * The index of the receive queue from which to retrieve input packets.
+ * The value must be in the range [0, nb_rx_queue - 1] previously supplied
+ * to rte_eth_dev_configure().
+ * @return
+ * - (0) if successful.
+ * - (-ENOTSUP) if underlying hardware OR driver doesn't support
+ * that operation.
+ * - (-ENODEV) if *port_id* invalid.
+ */
+int rte_eth_dev_rx_intr_disable(uint8_t port_id, uint16_t queue_id);
+
+/**
+ * RX Interrupt control per port.
+ *
+ * @param port_id
+ * The port identifier of the Ethernet device.
+ * @param epfd
+ * Epoll instance fd which the intr vector associated to.
+ * Using RTE_EPOLL_PER_THREAD allows to use per thread epoll instance.
+ * @param op
+ * The operation be performed for the vector.
+ * Operation type of {RTE_INTR_EVENT_ADD, RTE_INTR_EVENT_DEL}.
+ * @param data
+ * User raw data.
+ * @return
+ * - On success, zero.
+ * - On failure, a negative value.
+ */
+int rte_eth_dev_rx_intr_ctl(uint8_t port_id, int epfd, int op, void *data);
+
+/**
+ * RX Interrupt control per queue.
+ *
+ * @param port_id
+ * The port identifier of the Ethernet device.
+ * @param queue_id
+ * The index of the receive queue from which to retrieve input packets.
+ * The value must be in the range [0, nb_rx_queue - 1] previously supplied
+ * to rte_eth_dev_configure().
+ * @param epfd
+ * Epoll instance fd which the intr vector associated to.
+ * Using RTE_EPOLL_PER_THREAD allows to use per thread epoll instance.
+ * @param op
+ * The operation be performed for the vector.
+ * Operation type of {RTE_INTR_EVENT_ADD, RTE_INTR_EVENT_DEL}.
+ * @param data
+ * User raw data.
+ * @return
+ * - On success, zero.
+ * - On failure, a negative value.
+ */
+int rte_eth_dev_rx_intr_ctl_q(uint8_t port_id, uint16_t queue_id,
+ int epfd, int op, void *data);
+
/**
* Turn on the LED on the Ethernet device.
* This function turns on the LED on the Ethernet device.
*/
int rte_eth_dev_mac_addr_remove(uint8_t port, struct ether_addr *mac_addr);
+/**
+ * Set the default MAC address.
+ *
+ * @param port
+ * The port identifier of the Ethernet device.
+ * @param mac_addr
+ * New default MAC address.
+ * @return
+ * - (0) if successful, or *mac_addr* didn't exist.
+ * - (-ENOTSUP) if hardware doesn't support.
+ * - (-ENODEV) if *port* invalid.
+ * - (-EINVAL) if MAC address is invalid.
+ */
+int rte_eth_dev_default_mac_addr_set(uint8_t port, struct ether_addr *mac_addr);
+
+
/**
* Update Redirection Table(RETA) of Receive Side Scaling of Ethernet device.
*
* @param port
* The port identifier of the Ethernet device.
* @param reta_conf
- * RETA to update.
+ * RETA to update.
+ * @param reta_size
+ * Redirection table size. The table size can be queried by
+ * rte_eth_dev_info_get().
* @return
* - (0) if successful.
* - (-ENOTSUP) if hardware doesn't support.
* - (-EINVAL) if bad parameter.
*/
int rte_eth_dev_rss_reta_update(uint8_t port,
- struct rte_eth_rss_reta *reta_conf);
+ struct rte_eth_rss_reta_entry64 *reta_conf,
+ uint16_t reta_size);
/**
* Query Redirection Table(RETA) of Receive Side Scaling of Ethernet device.
* The port identifier of the Ethernet device.
* @param reta_conf
* RETA to query.
+ * @param reta_size
+ * Redirection table size. The table size can be queried by
+ * rte_eth_dev_info_get().
* @return
* - (0) if successful.
* - (-ENOTSUP) if hardware doesn't support.
* - (-EINVAL) if bad parameter.
*/
int rte_eth_dev_rss_reta_query(uint8_t port,
- struct rte_eth_rss_reta *reta_conf);
+ struct rte_eth_rss_reta_entry64 *reta_conf,
+ uint16_t reta_size);
/**
* Updates unicast hash table for receiving packet with the given destination
* - (-EINVAL) if the mr_conf information is not correct.
*/
int rte_eth_mirror_rule_set(uint8_t port_id,
- struct rte_eth_vmdq_mirror_conf *mirror_conf,
+ struct rte_eth_mirror_conf *mirror_conf,
uint8_t rule_id,
uint8_t on);
*
* @param port
* The port identifier of the Ethernet device.
- * @param state
+ * @param new_state
* The current bypass state.
* - (1) Normal mode
* - (2) Bypass mode
*
* @param port
* The port identifier of the Ethernet device.
- * @param state
+ * @param timeout
* The timeout to be set.
* - (0) 0 seconds (timer is off)
* - (1) 1.5 seconds
/**
* Configuration of Receive Side Scaling hash computation of Ethernet device.
*
- * @param port
+ * @param port_id
* The port identifier of the Ethernet device.
* @param rss_conf
* The new configuration to use for RSS hash computation on the port.
* Retrieve current configuration of Receive Side Scaling hash computation
* of Ethernet device.
*
- * @param port
+ * @param port_id
* The port identifier of the Ethernet device.
* @param rss_conf
* Where to store the current RSS hash configuration of the Ethernet device.
rte_eth_dev_rss_hash_conf_get(uint8_t port_id,
struct rte_eth_rss_conf *rss_conf);
+ /**
+ * Add UDP tunneling port of an Ethernet device for filtering a specific
+ * tunneling packet by UDP port number.
+ *
+ * @param port_id
+ * The port identifier of the Ethernet device.
+ * @param tunnel_udp
+ * UDP tunneling configuration.
+ *
+ * @return
+ * - (0) if successful.
+ * - (-ENODEV) if port identifier is invalid.
+ * - (-ENOTSUP) if hardware doesn't support tunnel type.
+ */
+int
+rte_eth_dev_udp_tunnel_add(uint8_t port_id,
+ struct rte_eth_udp_tunnel *tunnel_udp);
+
+ /**
+ * Detete UDP tunneling port configuration of Ethernet device
+ *
+ * @param port_id
+ * The port identifier of the Ethernet device.
+ * @param tunnel_udp
+ * UDP tunneling configuration.
+ *
+ * @return
+ * - (0) if successful.
+ * - (-ENODEV) if port identifier is invalid.
+ * - (-ENOTSUP) if hardware doesn't support tunnel type.
+ */
+int
+rte_eth_dev_udp_tunnel_delete(uint8_t port_id,
+ struct rte_eth_udp_tunnel *tunnel_udp);
+
/**
- * add syn filter
+ * Check whether the filter type is supported on an Ethernet device.
+ * All the supported filter types are defined in 'rte_eth_ctrl.h'.
*
* @param port_id
* The port identifier of the Ethernet device.
- * @param rx_queue
- * The index of RX queue where to store RX packets matching the syn filter.
- * @param filter
- * The pointer to the structure describing the syn filter rule.
+ * @param filter_type
+ * Filter type.
* @return
* - (0) if successful.
- * - (-ENOTSUP) if hardware doesn't support.
- * - (-EINVAL) if bad parameter.
+ * - (-ENOTSUP) if hardware doesn't support this filter type.
+ * - (-ENODEV) if *port_id* invalid.
*/
-int rte_eth_dev_add_syn_filter(uint8_t port_id,
- struct rte_syn_filter *filter, uint16_t rx_queue);
+int rte_eth_dev_filter_supported(uint8_t port_id, enum rte_filter_type filter_type);
/**
- * remove syn filter
+ * Take operations to assigned filter type on an Ethernet device.
+ * All the supported operations and filter types are defined in 'rte_eth_ctrl.h'.
*
* @param port_id
* The port identifier of the Ethernet device.
+ * @param filter_type
+ * Filter type.
+ * @param filter_op
+ * Type of operation.
+ * @param arg
+ * A pointer to arguments defined specifically for the operation.
* @return
* - (0) if successful.
* - (-ENOTSUP) if hardware doesn't support.
- * - (-EINVAL) if bad parameter.
+ * - (-ENODEV) if *port_id* invalid.
+ * - others depends on the specific operations implementation.
*/
-int rte_eth_dev_remove_syn_filter(uint8_t port_id);
+int rte_eth_dev_filter_ctrl(uint8_t port_id, enum rte_filter_type filter_type,
+ enum rte_filter_op filter_op, void *arg);
/**
- * get syn filter
+ * Get DCB information on an Ethernet device.
*
* @param port_id
* The port identifier of the Ethernet device.
- * @param filter
- * The pointer to the structure describing the syn filter.
- * @param rx_queue
- * A pointer to get the queue index of syn filter.
+ * @param dcb_info
+ * dcb information.
* @return
* - (0) if successful.
+ * - (-ENODEV) if port identifier is invalid.
* - (-ENOTSUP) if hardware doesn't support.
- * - (-EINVAL) if bad parameter.
*/
-int rte_eth_dev_get_syn_filter(uint8_t port_id,
- struct rte_syn_filter *filter, uint16_t *rx_queue);
+int rte_eth_dev_get_dcb_info(uint8_t port_id,
+ struct rte_eth_dcb_info *dcb_info);
/**
- * Add a new ethertype filter rule on an Ethernet device.
+ * Add a callback to be called on packet RX on a given port and queue.
+ *
+ * This API configures a function to be called for each burst of
+ * packets received on a given NIC port queue. The return value is a pointer
+ * that can be used to later remove the callback using
+ * rte_eth_remove_rx_callback().
+ *
+ * Multiple functions are called in the order that they are added.
*
* @param port_id
* The port identifier of the Ethernet device.
- * @param index
- * The identifier of ethertype filter.
- * @param filter
- * The pointer to the structure describing the ethertype filter rule.
- * The *rte_ethertype_filter* structure includes the values of the different
- * fields to match: ethertype and priority in vlan tag.
- * priority in vlan tag is not supported for E1000 dev.
- * @param rx_queue
- * The index of the RX queue where to store RX packets matching the added
- * ethertype filter.
+ * @param queue_id
+ * The queue on the Ethernet device on which the callback is to be added.
+ * @param fn
+ * The callback function
+ * @param user_param
+ * A generic pointer parameter which will be passed to each invocation of the
+ * callback function on this port and queue.
+ *
* @return
- * - (0) if successful.
- * - (-ENOTSUP) if hardware doesn't support ethertype filter.
- * - (-ENODEV) if *port_id* invalid.
- * - (-EINVAL) if the filter information is not correct.
+ * NULL on error.
+ * On success, a pointer value which can later be used to remove the callback.
*/
-int rte_eth_dev_add_ethertype_filter(uint8_t port_id, uint16_t index,
- struct rte_ethertype_filter *filter, uint16_t rx_queue);
+void *rte_eth_add_rx_callback(uint8_t port_id, uint16_t queue_id,
+ rte_rx_callback_fn fn, void *user_param);
/**
- * remove an ethertype filter rule on an Ethernet device.
+ * Add a callback to be called on packet TX on a given port and queue.
+ *
+ * This API configures a function to be called for each burst of
+ * packets sent on a given NIC port queue. The return value is a pointer
+ * that can be used to later remove the callback using
+ * rte_eth_remove_tx_callback().
+ *
+ * Multiple functions are called in the order that they are added.
*
* @param port_id
* The port identifier of the Ethernet device.
- * @param index
- * The identifier of ethertype filter.
+ * @param queue_id
+ * The queue on the Ethernet device on which the callback is to be added.
+ * @param fn
+ * The callback function
+ * @param user_param
+ * A generic pointer parameter which will be passed to each invocation of the
+ * callback function on this port and queue.
+ *
* @return
- * - (0) if successful.
- * - (-ENOTSUP) if hardware doesn't support ethertype filter.
- * - (-ENODEV) if *port_id* invalid.
- * - (-EINVAL) if the filter information is not correct.
+ * NULL on error.
+ * On success, a pointer value which can later be used to remove the callback.
*/
-int rte_eth_dev_remove_ethertype_filter(uint8_t port_id,
- uint16_t index);
+void *rte_eth_add_tx_callback(uint8_t port_id, uint16_t queue_id,
+ rte_tx_callback_fn fn, void *user_param);
/**
- * Get an ethertype filter rule on an Ethernet device.
+ * Remove an RX packet callback from a given port and queue.
+ *
+ * This function is used to removed callbacks that were added to a NIC port
+ * queue using rte_eth_add_rx_callback().
+ *
+ * Note: the callback is removed from the callback list but it isn't freed
+ * since the it may still be in use. The memory for the callback can be
+ * subsequently freed back by the application by calling rte_free():
+ *
+ * - Immediately - if the port is stopped, or the user knows that no
+ * callbacks are in flight e.g. if called from the thread doing RX/TX
+ * on that queue.
+ *
+ * - After a short delay - where the delay is sufficient to allow any
+ * in-flight callbacks to complete.
*
* @param port_id
* The port identifier of the Ethernet device.
- * @param index
- * The identifier of ethertype filter.
- * @param filter
- * A pointer to a structure of type *rte_ethertype_filter* to be filled with
- * the information of the Ethertype filter.
- * @param rx_queue
- * A pointer to get the queue index.
+ * @param queue_id
+ * The queue on the Ethernet device from which the callback is to be removed.
+ * @param user_cb
+ * User supplied callback created via rte_eth_add_rx_callback().
+ *
* @return
- * - (0) if successful.
- * - (-ENOTSUP) if hardware doesn't support ethertype filter.
- * - (-ENODEV) if *port_id* invalid.
- * - (-EINVAL) if the filter information is not correct.
- * - (-ENOENT) if no enabled filter in this index.
+ * - 0: Success. Callback was removed.
+ * - -ENOTSUP: Callback support is not available.
+ * - -EINVAL: The port_id or the queue_id is out of range, or the callback
+ * is NULL or not found for the port/queue.
*/
-int rte_eth_dev_get_ethertype_filter(uint8_t port_id, uint16_t index,
- struct rte_ethertype_filter *filter, uint16_t *rx_queue);
+int rte_eth_remove_rx_callback(uint8_t port_id, uint16_t queue_id,
+ struct rte_eth_rxtx_callback *user_cb);
/**
- * Add a new 2tuple filter rule on an Ethernet device.
+ * Remove a TX packet callback from a given port and queue.
+ *
+ * This function is used to removed callbacks that were added to a NIC port
+ * queue using rte_eth_add_tx_callback().
+ *
+ * Note: the callback is removed from the callback list but it isn't freed
+ * since the it may still be in use. The memory for the callback can be
+ * subsequently freed back by the application by calling rte_free():
+ *
+ * - Immediately - if the port is stopped, or the user knows that no
+ * callbacks are in flight e.g. if called from the thread doing RX/TX
+ * on that queue.
+ *
+ * - After a short delay - where the delay is sufficient to allow any
+ * in-flight callbacks to complete.
*
* @param port_id
* The port identifier of the Ethernet device.
- * @param index
- * The identifier of 2tuple filter.
- * @param filter
- * The pointer to the structure describing the 2tuple filter rule.
- * The *rte_2tuple_filter* structure includes the values of the different
- * fields to match: protocol, dst_port and
- * tcp_flags if the protocol is tcp type.
- * @param rx_queue
- * The index of the RX queue where to store RX packets matching the added
- * 2tuple filter.
+ * @param queue_id
+ * The queue on the Ethernet device from which the callback is to be removed.
+ * @param user_cb
+ * User supplied callback created via rte_eth_add_tx_callback().
+ *
* @return
- * - (0) if successful.
- * - (-ENOTSUP) if hardware doesn't support 2tuple filter.
- * - (-ENODEV) if *port_id* invalid.
- * - (-EINVAL) if the filter information is not correct.
+ * - 0: Success. Callback was removed.
+ * - -ENOTSUP: Callback support is not available.
+ * - -EINVAL: The port_id or the queue_id is out of range, or the callback
+ * is NULL or not found for the port/queue.
*/
-int rte_eth_dev_add_2tuple_filter(uint8_t port_id, uint16_t index,
- struct rte_2tuple_filter *filter, uint16_t rx_queue);
+int rte_eth_remove_tx_callback(uint8_t port_id, uint16_t queue_id,
+ struct rte_eth_rxtx_callback *user_cb);
/**
- * remove a 2tuple filter rule on an Ethernet device.
+ * Retrieve number of available registers for access
*
* @param port_id
* The port identifier of the Ethernet device.
- * @param index
- * The identifier of 2tuple filter.
* @return
- * - (0) if successful.
- * - (-ENOTSUP) if hardware doesn't support 2tuple filter.
+ * - (>=0) number of registers if successful.
+ * - (-ENOTSUP) if hardware doesn't support.
* - (-ENODEV) if *port_id* invalid.
- * - (-EINVAL) if the filter information is not correct.
+ * - others depends on the specific operations implementation.
*/
-int rte_eth_dev_remove_2tuple_filter(uint8_t port_id, uint16_t index);
+int rte_eth_dev_get_reg_length(uint8_t port_id);
/**
- * Get an 2tuple filter rule on an Ethernet device.
+ * Retrieve device registers and register attributes
*
* @param port_id
* The port identifier of the Ethernet device.
- * @param index
- * The identifier of 2tuple filter.
- * @param filter
- * A pointer to a structure of type *rte_2tuple_filter* to be filled with
- * the information of the 2tuple filter.
- * @param rx_queue
- * A pointer to get the queue index.
+ * @param info
+ * The template includes buffer for register data and attribute to be filled.
* @return
* - (0) if successful.
- * - (-ENOTSUP) if hardware doesn't support 2tuple filter.
+ * - (-ENOTSUP) if hardware doesn't support.
* - (-ENODEV) if *port_id* invalid.
- * - (-EINVAL) if the filter information is not correct.
- * - (-ENOENT) if no enabled filter in this index.
+ * - others depends on the specific operations implementation.
*/
-int rte_eth_dev_get_2tuple_filter(uint8_t port_id, uint16_t index,
- struct rte_2tuple_filter *filter, uint16_t *rx_queue);
+int rte_eth_dev_get_reg_info(uint8_t port_id, struct rte_dev_reg_info *info);
/**
- * Add a new 5tuple filter rule on an Ethernet device.
+ * Retrieve size of device EEPROM
*
* @param port_id
* The port identifier of the Ethernet device.
- * @param index
- * The identifier of 5tuple filter.
- * @param filter
- * The pointer to the structure describing the 5tuple filter rule.
- * The *rte_5tuple_filter* structure includes the values of the different
- * fields to match: dst src IP, dst src port, protocol and relative masks
- * @param rx_queue
- * The index of the RX queue where to store RX packets matching the added
- * 5tuple filter.
* @return
- * - (0) if successful.
- * - (-ENOTSUP) if hardware doesn't support 5tuple filter.
+ * - (>=0) EEPROM size if successful.
+ * - (-ENOTSUP) if hardware doesn't support.
* - (-ENODEV) if *port_id* invalid.
- * - (-EINVAL) if the filter information is not correct.
+ * - others depends on the specific operations implementation.
*/
-int rte_eth_dev_add_5tuple_filter(uint8_t port_id, uint16_t index,
- struct rte_5tuple_filter *filter, uint16_t rx_queue);
+int rte_eth_dev_get_eeprom_length(uint8_t port_id);
/**
- * remove a 5tuple filter rule on an Ethernet device.
+ * Retrieve EEPROM and EEPROM attribute
*
* @param port_id
* The port identifier of the Ethernet device.
- * @param index
- * The identifier of 5tuple filter.
+ * @param info
+ * The template includes buffer for return EEPROM data and
+ * EEPROM attributes to be filled.
* @return
* - (0) if successful.
- * - (-ENOTSUP) if hardware doesn't support 5tuple filter.
+ * - (-ENOTSUP) if hardware doesn't support.
* - (-ENODEV) if *port_id* invalid.
- * - (-EINVAL) if the filter information is not correct.
+ * - others depends on the specific operations implementation.
*/
-int rte_eth_dev_remove_5tuple_filter(uint8_t port_id, uint16_t index);
+int rte_eth_dev_get_eeprom(uint8_t port_id, struct rte_dev_eeprom_info *info);
/**
- * Get an 5tuple filter rule on an Ethernet device.
+ * Program EEPROM with provided data
*
* @param port_id
* The port identifier of the Ethernet device.
- * @param index
- * The identifier of 5tuple filter.
- * @param filter
- * A pointer to a structure of type *rte_5tuple_filter* to be filled with
- * the information of the 5tuple filter.
- * @param rx_queue
- * A pointer to get the queue index.
+ * @param info
+ * The template includes EEPROM data for programming and
+ * EEPROM attributes to be filled
* @return
* - (0) if successful.
- * - (-ENOTSUP) if hardware doesn't support 5tuple filter.
+ * - (-ENOTSUP) if hardware doesn't support.
* - (-ENODEV) if *port_id* invalid.
- * - (-EINVAL) if the filter information is not correct.
+ * - others depends on the specific operations implementation.
*/
-int rte_eth_dev_get_5tuple_filter(uint8_t port_id, uint16_t index,
- struct rte_5tuple_filter *filter, uint16_t *rx_queue);
+int rte_eth_dev_set_eeprom(uint8_t port_id, struct rte_dev_eeprom_info *info);
/**
- * Add a new flex filter rule on an Ethernet device.
+ * Set the list of multicast addresses to filter on an Ethernet device.
*
* @param port_id
* The port identifier of the Ethernet device.
- * @param index
- * The identifier of flex filter.
- * @param filter
- * The pointer to the structure describing the flex filter rule.
- * The *rte_flex_filter* structure includes the values of the different fields
- * to match: the dwords (first len bytes of packet ) and relative masks.
- * @param rx_queue
- * The index of the RX queue where to store RX packets matching the added
- * flex filter.
+ * @param mc_addr_set
+ * The array of multicast addresses to set. Equal to NULL when the function
+ * is invoked to flush the set of filtered addresses.
+ * @param nb_mc_addr
+ * The number of multicast addresses in the *mc_addr_set* array. Equal to 0
+ * when the function is invoked to flush the set of filtered addresses.
* @return
* - (0) if successful.
- * - (-ENOTSUP) if hardware doesn't support flex filter.
* - (-ENODEV) if *port_id* invalid.
- * - (-EINVAL) if the filter information is not correct.
- * - (-ENOENT) if no enabled filter in this index.
+ * - (-ENOTSUP) if PMD of *port_id* doesn't support multicast filtering.
+ * - (-ENOSPC) if *port_id* has not enough multicast filtering resources.
*/
-int rte_eth_dev_add_flex_filter(uint8_t port_id, uint16_t index,
- struct rte_flex_filter *filter, uint16_t rx_queue);
+int rte_eth_dev_set_mc_addr_list(uint8_t port_id,
+ struct ether_addr *mc_addr_set,
+ uint32_t nb_mc_addr);
/**
- * remove a flex filter rule on an Ethernet device.
+ * Enable IEEE1588/802.1AS timestamping for an Ethernet device.
*
* @param port_id
* The port identifier of the Ethernet device.
- * @param index
- * The identifier of flex filter.
+ *
* @return
- * - (0) if successful.
- * - (-ENOTSUP) if hardware doesn't support flex filter.
- * - (-ENODEV) if *port_id* invalid.
- * - (-EINVAL) if the filter information is not correct.
+ * - 0: Success.
+ * - -ENODEV: The port ID is invalid.
+ * - -ENOTSUP: The function is not supported by the Ethernet driver.
*/
-int rte_eth_dev_remove_flex_filter(uint8_t port_id, uint16_t index);
+extern int rte_eth_timesync_enable(uint8_t port_id);
/**
- * Get an flex filter rule on an Ethernet device.
+ * Disable IEEE1588/802.1AS timestamping for an Ethernet device.
*
* @param port_id
* The port identifier of the Ethernet device.
- * @param index
- * The identifier of flex filter.
- * @param filter
- * A pointer to a structure of type *rte_flex_filter* to be filled with
- * the information of the flex filter.
- * @param rx_queue
- * A pointer to get the queue index.
+ *
* @return
- * - (0) if successful.
- * - (-ENOTSUP) if hardware doesn't support flex filter.
- * - (-ENODEV) if *port_id* invalid.
- * - (-EINVAL) if the filter information is not correct.
- * - (-ENOENT) if no enabled filter in this index.
+ * - 0: Success.
+ * - -ENODEV: The port ID is invalid.
+ * - -ENOTSUP: The function is not supported by the Ethernet driver.
+ */
+extern int rte_eth_timesync_disable(uint8_t port_id);
+
+/**
+ * Read an IEEE1588/802.1AS RX timestamp from an Ethernet device.
+ *
+ * @param port_id
+ * The port identifier of the Ethernet device.
+ * @param timestamp
+ * Pointer to the timestamp struct.
+ * @param flags
+ * Device specific flags. Used to pass the RX timesync register index to
+ * i40e. Unused in igb/ixgbe, pass 0 instead.
+ *
+ * @return
+ * - 0: Success.
+ * - -EINVAL: No timestamp is available.
+ * - -ENODEV: The port ID is invalid.
+ * - -ENOTSUP: The function is not supported by the Ethernet driver.
+ */
+extern int rte_eth_timesync_read_rx_timestamp(uint8_t port_id,
+ struct timespec *timestamp,
+ uint32_t flags);
+
+/**
+ * Read an IEEE1588/802.1AS TX timestamp from an Ethernet device.
+ *
+ * @param port_id
+ * The port identifier of the Ethernet device.
+ * @param timestamp
+ * Pointer to the timestamp struct.
+ *
+ * @return
+ * - 0: Success.
+ * - -EINVAL: No timestamp is available.
+ * - -ENODEV: The port ID is invalid.
+ * - -ENOTSUP: The function is not supported by the Ethernet driver.
*/
-int rte_eth_dev_get_flex_filter(uint8_t port_id, uint16_t index,
- struct rte_flex_filter *filter, uint16_t *rx_queue);
+extern int rte_eth_timesync_read_tx_timestamp(uint8_t port_id,
+ struct timespec *timestamp);
#ifdef __cplusplus
}