/*******************************************************************************
-Copyright (c) 2001-2012, Intel Corporation
+Copyright (c) 2001-2014, Intel Corporation
All rights reserved.
Redistribution and use in source and binary forms, with or without
STATIC s32 e1000_acquire_nvm_82575(struct e1000_hw *hw);
STATIC void e1000_release_nvm_82575(struct e1000_hw *hw);
STATIC s32 e1000_check_for_link_82575(struct e1000_hw *hw);
+STATIC s32 e1000_check_for_link_media_swap(struct e1000_hw *hw);
STATIC s32 e1000_get_cfg_done_82575(struct e1000_hw *hw);
STATIC s32 e1000_get_link_up_info_82575(struct e1000_hw *hw, u16 *speed,
u16 *duplex);
-STATIC s32 e1000_init_hw_82575(struct e1000_hw *hw);
STATIC s32 e1000_phy_hw_reset_sgmii_82575(struct e1000_hw *hw);
STATIC s32 e1000_read_phy_reg_sgmii_82575(struct e1000_hw *hw, u32 offset,
u16 *data);
u32 offset, u16 data);
STATIC void e1000_clear_hw_cntrs_82575(struct e1000_hw *hw);
STATIC s32 e1000_acquire_swfw_sync_82575(struct e1000_hw *hw, u16 mask);
-static s32 e1000_get_pcs_speed_and_duplex_82575(struct e1000_hw *hw,
+STATIC s32 e1000_get_pcs_speed_and_duplex_82575(struct e1000_hw *hw,
u16 *speed, u16 *duplex);
-static s32 e1000_get_phy_id_82575(struct e1000_hw *hw);
+STATIC s32 e1000_get_phy_id_82575(struct e1000_hw *hw);
STATIC void e1000_release_swfw_sync_82575(struct e1000_hw *hw, u16 mask);
-static bool e1000_sgmii_active_82575(struct e1000_hw *hw);
+STATIC bool e1000_sgmii_active_82575(struct e1000_hw *hw);
STATIC s32 e1000_reset_init_script_82575(struct e1000_hw *hw);
STATIC s32 e1000_read_mac_addr_82575(struct e1000_hw *hw);
STATIC void e1000_config_collision_dist_82575(struct e1000_hw *hw);
STATIC s32 e1000_set_i2c_data(struct e1000_hw *hw, u32 *i2cctl, bool data);
STATIC bool e1000_get_i2c_data(u32 *i2cctl);
-static const u16 e1000_82580_rxpbs_table[] = {
+STATIC const u16 e1000_82580_rxpbs_table[] = {
36, 72, 144, 1, 2, 4, 8, 16, 35, 70, 140 };
#define E1000_82580_RXPBS_TABLE_SIZE \
- (sizeof(e1000_82580_rxpbs_table)/sizeof(u16))
+ (sizeof(e1000_82580_rxpbs_table) / \
+ sizeof(e1000_82580_rxpbs_table[0]))
/**
break;
case e1000_82580:
case e1000_i350:
+ case e1000_i354:
case e1000_i210:
case e1000_i211:
reg = E1000_READ_REG(hw, E1000_MDICNFG);
switch (hw->mac.type) {
case e1000_82580:
case e1000_i350:
+ case e1000_i354:
phy->ops.read_reg = e1000_read_phy_reg_82580;
phy->ops.write_reg = e1000_write_phy_reg_82580;
break;
/* Verify phy id and set remaining function pointers */
switch (phy->id) {
+ case M88E1543_E_PHY_ID:
+ case M88E1512_E_PHY_ID:
case I347AT4_E_PHY_ID:
case M88E1112_E_PHY_ID:
case M88E1340M_E_PHY_ID:
phy->id == M88E1340M_E_PHY_ID)
phy->ops.get_cable_length =
e1000_get_cable_length_m88_gen2;
+ else if (phy->id == M88E1543_E_PHY_ID ||
+ phy->id == M88E1512_E_PHY_ID)
+ phy->ops.get_cable_length =
+ e1000_get_cable_length_m88_gen2;
else
phy->ops.get_cable_length = e1000_get_cable_length_m88;
phy->ops.force_speed_duplex = e1000_phy_force_speed_duplex_m88;
+ /* Check if this PHY is confgured for media swap. */
+ if (phy->id == M88E1112_E_PHY_ID) {
+ u16 data;
+
+ ret_val = phy->ops.write_reg(hw,
+ E1000_M88E1112_PAGE_ADDR,
+ 2);
+ if (ret_val)
+ goto out;
+
+ ret_val = phy->ops.read_reg(hw,
+ E1000_M88E1112_MAC_CTRL_1,
+ &data);
+ if (ret_val)
+ goto out;
+
+ data = (data & E1000_M88E1112_MAC_CTRL_1_MODE_MASK) >>
+ E1000_M88E1112_MAC_CTRL_1_MODE_SHIFT;
+ if (data == E1000_M88E1112_AUTO_COPPER_SGMII ||
+ data == E1000_M88E1112_AUTO_COPPER_BASEX)
+ hw->mac.ops.check_for_link =
+ e1000_check_for_link_media_swap;
+ }
+ if (phy->id == M88E1512_E_PHY_ID) {
+ ret_val = e1000_initialize_M88E1512_phy(hw);
+ if (ret_val)
+ goto out;
+ }
break;
case IGP03E1000_E_PHY_ID:
case IGP04E1000_E_PHY_ID:
} else {
nvm->type = e1000_nvm_flash_hw;
}
+
/* Function Pointers */
nvm->ops.acquire = e1000_acquire_nvm_82575;
nvm->ops.release = e1000_release_nvm_82575;
nvm->ops.update = e1000_update_nvm_checksum_82580;
break;
case e1000_i350:
+ case e1000_i354:
nvm->ops.validate = e1000_validate_nvm_checksum_i350;
nvm->ops.update = e1000_update_nvm_checksum_i350;
break;
mac->rar_entry_count = E1000_RAR_ENTRIES_82576;
if (mac->type == e1000_82580)
mac->rar_entry_count = E1000_RAR_ENTRIES_82580;
- if (mac->type == e1000_i350) {
+ if (mac->type == e1000_i350 || mac->type == e1000_i354)
mac->rar_entry_count = E1000_RAR_ENTRIES_I350;
- /* Enable EEE default settings for i350 */
+
+ /* Enable EEE default settings for EEE supported devices */
+ if (mac->type >= e1000_i350)
dev_spec->eee_disable = false;
- }
+
+ /* Allow a single clear of the SW semaphore on I210 and newer */
+ if (mac->type >= e1000_i210)
+ dev_spec->clear_semaphore_once = true;
/* Set if part includes ASF firmware */
mac->asf_firmware_present = true;
else
mac->ops.reset_hw = e1000_reset_hw_82575;
/* hw initialization */
+ if ((mac->type == e1000_i210) || (mac->type == e1000_i211))
+ mac->ops.init_hw = e1000_init_hw_i210;
+ else
mac->ops.init_hw = e1000_init_hw_82575;
/* link setup */
mac->ops.setup_link = e1000_setup_link_generic;
mac->ops.config_collision_dist = e1000_config_collision_dist_82575;
/* multicast address update */
mac->ops.update_mc_addr_list = e1000_update_mc_addr_list_generic;
- if (mac->type == e1000_i350) {
+ if (hw->mac.type == e1000_i350 || mac->type == e1000_i354) {
/* writing VFTA */
mac->ops.write_vfta = e1000_write_vfta_i350;
/* clearing VFTA */
DEBUGFUNC("e1000_get_phy_id_82575");
+ /* some i354 devices need an extra read for phy id */
+ if (hw->mac.type == e1000_i354)
+ e1000_get_phy_id(hw);
+
/*
* For SGMII PHYs, we try the list of possible addresses until
* we find one that works. For non-SGMII PHYs
break;
case e1000_82580:
case e1000_i350:
+ case e1000_i354:
case e1000_i210:
case e1000_i211:
mdic = E1000_READ_REG(hw, E1000_MDICNFG);
STATIC s32 e1000_phy_hw_reset_sgmii_82575(struct e1000_hw *hw)
{
s32 ret_val = E1000_SUCCESS;
+ struct e1000_phy_info *phy = &hw->phy;
DEBUGFUNC("e1000_phy_hw_reset_sgmii_82575");
goto out;
ret_val = hw->phy.ops.commit(hw);
+ if (ret_val)
+ goto out;
+ if (phy->id == M88E1512_E_PHY_ID)
+ ret_val = e1000_initialize_M88E1512_phy(hw);
out:
return ret_val;
}
return ret_val;
}
+/**
+ * e1000_check_for_link_media_swap - Check which M88E1112 interface linked
+ * @hw: pointer to the HW structure
+ *
+ * Poll the M88E1112 interfaces to see which interface achieved link.
+ */
+STATIC s32 e1000_check_for_link_media_swap(struct e1000_hw *hw)
+{
+ struct e1000_phy_info *phy = &hw->phy;
+ s32 ret_val;
+ u16 data;
+ u8 port = 0;
+
+ DEBUGFUNC("e1000_check_for_link_media_swap");
+
+ /* Check the copper medium. */
+ ret_val = phy->ops.write_reg(hw, E1000_M88E1112_PAGE_ADDR, 0);
+ if (ret_val)
+ return ret_val;
+
+ ret_val = phy->ops.read_reg(hw, E1000_M88E1112_STATUS, &data);
+ if (ret_val)
+ return ret_val;
+
+ if (data & E1000_M88E1112_STATUS_LINK)
+ port = E1000_MEDIA_PORT_COPPER;
+
+ /* Check the other medium. */
+ ret_val = phy->ops.write_reg(hw, E1000_M88E1112_PAGE_ADDR, 1);
+ if (ret_val)
+ return ret_val;
+
+ ret_val = phy->ops.read_reg(hw, E1000_M88E1112_STATUS, &data);
+ if (ret_val)
+ return ret_val;
+
+ /* reset page to 0 */
+ ret_val = phy->ops.write_reg(hw, E1000_M88E1112_PAGE_ADDR, 0);
+ if (ret_val)
+ return ret_val;
+
+ if (data & E1000_M88E1112_STATUS_LINK)
+ port = E1000_MEDIA_PORT_OTHER;
+
+ /* Determine if a swap needs to happen. */
+ if (port && (hw->dev_spec._82575.media_port != port)) {
+ hw->dev_spec._82575.media_port = port;
+ hw->dev_spec._82575.media_changed = true;
+ } else {
+ ret_val = e1000_check_for_link_82575(hw);
+ }
+
+ return E1000_SUCCESS;
+}
+
/**
* e1000_power_up_serdes_link_82575 - Power up the serdes link after shutdown
* @hw: pointer to the HW structure
* Using the physical coding sub-layer (PCS), retrieve the current speed and
* duplex, then store the values in the pointers provided.
**/
-static s32 e1000_get_pcs_speed_and_duplex_82575(struct e1000_hw *hw,
+STATIC s32 e1000_get_pcs_speed_and_duplex_82575(struct e1000_hw *hw,
u16 *speed, u16 *duplex)
{
struct e1000_mac_info *mac = &hw->mac;
u32 pcs;
+ u32 status;
DEBUGFUNC("e1000_get_pcs_speed_and_duplex_82575");
else
*duplex = HALF_DUPLEX;
+ /* Check if it is an I354 2.5Gb backplane connection. */
+ if (mac->type == e1000_i354) {
+ status = E1000_READ_REG(hw, E1000_STATUS);
+ if ((status & E1000_STATUS_2P5_SKU) &&
+ !(status & E1000_STATUS_2P5_SKU_OVER)) {
+ *speed = SPEED_2500;
+ *duplex = FULL_DUPLEX;
+ DEBUGOUT("2500 Mbs, ");
+ DEBUGOUT("Full Duplex\n");
+ }
+ }
+
} else {
mac->serdes_has_link = false;
*speed = 0;
*
* This inits the hardware readying it for operation.
**/
-STATIC s32 e1000_init_hw_82575(struct e1000_hw *hw)
+s32 e1000_init_hw_82575(struct e1000_hw *hw)
{
struct e1000_mac_info *mac = &hw->mac;
s32 ret_val;
ctrl &= ~(E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX);
E1000_WRITE_REG(hw, E1000_CTRL, ctrl);
- /* Clear Go Link Disconnect bit */
- if (hw->mac.type >= e1000_82580) {
+ /* Clear Go Link Disconnect bit on supported devices */
+ switch (hw->mac.type) {
+ case e1000_82580:
+ case e1000_i350:
+ case e1000_i210:
+ case e1000_i211:
phpm_reg = E1000_READ_REG(hw, E1000_82580_PHY_POWER_MGMT);
phpm_reg &= ~E1000_82580_PM_GO_LINKD;
E1000_WRITE_REG(hw, E1000_82580_PHY_POWER_MGMT, phpm_reg);
+ break;
+ default:
+ break;
}
ret_val = e1000_setup_serdes_link_82575(hw);
switch (hw->phy.type) {
case e1000_phy_i210:
case e1000_phy_m88:
- if (hw->phy.id == I347AT4_E_PHY_ID ||
- hw->phy.id == M88E1112_E_PHY_ID ||
- hw->phy.id == M88E1340M_E_PHY_ID)
+ switch (hw->phy.id) {
+ case I347AT4_E_PHY_ID:
+ case M88E1112_E_PHY_ID:
+ case M88E1340M_E_PHY_ID:
+ case M88E1543_E_PHY_ID:
+ case M88E1512_E_PHY_ID:
+ case I210_I_PHY_ID:
ret_val = e1000_copper_link_setup_m88_gen2(hw);
- else
+ break;
+ default:
ret_val = e1000_copper_link_setup_m88(hw);
+ break;
+ }
break;
case e1000_phy_igp_3:
ret_val = e1000_copper_link_setup_igp(hw);
**/
STATIC s32 e1000_get_media_type_82575(struct e1000_hw *hw)
{
- u32 lan_id = 0;
- s32 ret_val = E1000_ERR_CONFIG;
struct e1000_dev_spec_82575 *dev_spec = &hw->dev_spec._82575;
+ s32 ret_val = E1000_SUCCESS;
u32 ctrl_ext = 0;
- u32 current_link_mode = 0;
- u16 init_ctrl_wd_3 = 0;
- u8 init_ctrl_wd_3_offset = 0;
- u8 init_ctrl_wd_3_bit_offset = 0;
+ u32 link_mode = 0;
/* Set internal phy as default */
dev_spec->sgmii_active = false;
dev_spec->module_plugged = false;
- /*
- * Check if NVM access method is attached already.
- * If it is then Init Control Word #3 is considered
- * otherwise runtime CSR register content is taken.
- */
-
/* Get CSR setting */
ctrl_ext = E1000_READ_REG(hw, E1000_CTRL_EXT);
- /* Get link mode setting */
- if ((hw->nvm.ops.read) && (hw->nvm.ops.read != e1000_null_read_nvm)) {
- /* Take link mode from EEPROM */
-
- /*
- * Get LAN port ID to derive its
- * adequate Init Control Word #3
- */
- lan_id = ((E1000_READ_REG(hw, E1000_STATUS) &
- E1000_STATUS_LAN_ID_MASK) >> E1000_STATUS_LAN_ID_OFFSET);
- /*
- * Derive Init Control Word #3 offset
- * and mask to pick up link mode setting.
- */
- if (hw->mac.type < e1000_82580) {
- init_ctrl_wd_3_offset = lan_id ?
- NVM_INIT_CONTROL3_PORT_A : NVM_INIT_CONTROL3_PORT_B;
- init_ctrl_wd_3_bit_offset = NVM_WORD24_LNK_MODE_OFFSET;
- } else {
- init_ctrl_wd_3_offset =
- NVM_82580_LAN_FUNC_OFFSET(lan_id) +
- NVM_INIT_CONTROL3_PORT_A;
- init_ctrl_wd_3_bit_offset =
- NVM_WORD24_82580_LNK_MODE_OFFSET;
- }
- /* Read Init Control Word #3*/
- hw->nvm.ops.read(hw, init_ctrl_wd_3_offset, 1, &init_ctrl_wd_3);
-
- /*
- * Align link mode bits to
- * their CTRL_EXT location.
- */
- current_link_mode = init_ctrl_wd_3;
- current_link_mode <<= (E1000_CTRL_EXT_LINK_MODE_OFFSET -
- init_ctrl_wd_3_bit_offset);
- current_link_mode &= E1000_CTRL_EXT_LINK_MODE_MASK;
-
- /*
- * Switch to CSR for all but internal PHY.
- */
- if (current_link_mode != E1000_CTRL_EXT_LINK_MODE_GMII)
- /* Take link mode from CSR */
- current_link_mode = ctrl_ext &
- E1000_CTRL_EXT_LINK_MODE_MASK;
- } else {
- /* Take link mode from CSR */
- current_link_mode = ctrl_ext & E1000_CTRL_EXT_LINK_MODE_MASK;
- }
-
- switch (current_link_mode) {
+ /* extract link mode setting */
+ link_mode = ctrl_ext & E1000_CTRL_EXT_LINK_MODE_MASK;
+ switch (link_mode) {
case E1000_CTRL_EXT_LINK_MODE_1000BASE_KX:
hw->phy.media_type = e1000_media_type_internal_serdes;
- current_link_mode = E1000_CTRL_EXT_LINK_MODE_1000BASE_KX;
break;
case E1000_CTRL_EXT_LINK_MODE_GMII:
hw->phy.media_type = e1000_media_type_copper;
- current_link_mode = E1000_CTRL_EXT_LINK_MODE_GMII;
break;
case E1000_CTRL_EXT_LINK_MODE_SGMII:
- case E1000_CTRL_EXT_LINK_MODE_PCIE_SERDES:
/* Get phy control interface type set (MDIO vs. I2C)*/
if (e1000_sgmii_uses_mdio_82575(hw)) {
hw->phy.media_type = e1000_media_type_copper;
dev_spec->sgmii_active = true;
- current_link_mode = E1000_CTRL_EXT_LINK_MODE_SGMII;
- } else {
- ret_val = e1000_set_sfp_media_type_82575(hw);
- if (ret_val != E1000_SUCCESS)
- goto out;
- if (hw->phy.media_type ==
- e1000_media_type_internal_serdes) {
- /* Keep Link Mode as SGMII for 100BaseFX */
- if (!dev_spec->eth_flags.e100_base_fx) {
- current_link_mode =
- E1000_CTRL_EXT_LINK_MODE_PCIE_SERDES;
- }
- } else if (hw->phy.media_type ==
- e1000_media_type_copper) {
- current_link_mode =
- E1000_CTRL_EXT_LINK_MODE_SGMII;
+ break;
+ }
+ /* fall through for I2C based SGMII */
+ case E1000_CTRL_EXT_LINK_MODE_PCIE_SERDES:
+ /* read media type from SFP EEPROM */
+ ret_val = e1000_set_sfp_media_type_82575(hw);
+ if ((ret_val != E1000_SUCCESS) ||
+ (hw->phy.media_type == e1000_media_type_unknown)) {
+ /*
+ * If media type was not identified then return media
+ * type defined by the CTRL_EXT settings.
+ */
+ hw->phy.media_type = e1000_media_type_internal_serdes;
+
+ if (link_mode == E1000_CTRL_EXT_LINK_MODE_SGMII) {
+ hw->phy.media_type = e1000_media_type_copper;
+ dev_spec->sgmii_active = true;
}
+
+ break;
}
- break;
- default:
- DEBUGOUT("Link mode mask doesn't fit bit field size\n");
- goto out;
- }
- /*
- * Do not change current link mode setting
- * if media type is fibre or has not been
- * recognized.
- */
- if ((hw->phy.media_type != e1000_media_type_unknown) &&
- (hw->phy.media_type != e1000_media_type_fiber)) {
- /* Update link mode */
+
+ /* do not change link mode for 100BaseFX */
+ if (dev_spec->eth_flags.e100_base_fx)
+ break;
+
+ /* change current link mode setting */
ctrl_ext &= ~E1000_CTRL_EXT_LINK_MODE_MASK;
- E1000_WRITE_REG(hw, E1000_CTRL_EXT, ctrl_ext |
- current_link_mode);
- }
- ret_val = E1000_SUCCESS;
-out:
- /*
- * If media type was not identified then return media type
- * defined by the CTRL_EXT settings.
- */
- if (hw->phy.media_type == e1000_media_type_unknown) {
- if (current_link_mode == E1000_CTRL_EXT_LINK_MODE_SGMII)
- hw->phy.media_type = e1000_media_type_copper;
+ if (hw->phy.media_type == e1000_media_type_copper)
+ ctrl_ext |= E1000_CTRL_EXT_LINK_MODE_SGMII;
else
- hw->phy.media_type = e1000_media_type_internal_serdes;
+ ctrl_ext |= E1000_CTRL_EXT_LINK_MODE_PCIE_SERDES;
+
+ E1000_WRITE_REG(hw, E1000_CTRL_EXT, ctrl_ext);
+
+ break;
}
return ret_val;
}
if (ret_val != E1000_SUCCESS)
goto out;
+
ret_val = e1000_read_sfp_data_byte(hw,
E1000_I2CCMD_SFP_DATA_ADDR(E1000_SFF_ETH_FLAGS_OFFSET),
(u8 *)eth_flags);
if (ret_val != E1000_SUCCESS)
goto out;
- /*
- * Check if there is some SFP
- * module plugged and powered
- */
+
+ /* Check if there is some SFP module plugged and powered */
if ((tranceiver_type == E1000_SFF_IDENTIFIER_SFP) ||
(tranceiver_type == E1000_SFF_IDENTIFIER_SFF)) {
dev_spec->module_plugged = true;
dev_spec->sgmii_active = true;
hw->phy.media_type = e1000_media_type_copper;
} else {
- hw->phy.media_type = e1000_media_type_unknown;
- DEBUGOUT("PHY module has not been recognized\n");
- goto out;
+ hw->phy.media_type = e1000_media_type_unknown;
+ DEBUGOUT("PHY module has not been recognized\n");
+ goto out;
}
} else {
hw->phy.media_type = e1000_media_type_unknown;
* which can be enabled for use in the embedded applications. Simply
* return the current state of the sgmii interface.
**/
-static bool e1000_sgmii_active_82575(struct e1000_hw *hw)
+STATIC bool e1000_sgmii_active_82575(struct e1000_hw *hw)
{
struct e1000_dev_spec_82575 *dev_spec = &hw->dev_spec._82575;
return dev_spec->sgmii_active;
**/
STATIC s32 e1000_read_mac_addr_82575(struct e1000_hw *hw)
{
- s32 ret_val = E1000_SUCCESS;
+ s32 ret_val;
DEBUGFUNC("e1000_read_mac_addr_82575");
**/
void e1000_vmdq_set_anti_spoofing_pf(struct e1000_hw *hw, bool enable, int pf)
{
- u32 dtxswc;
+ u32 reg_val, reg_offset;
switch (hw->mac.type) {
case e1000_82576:
- dtxswc = E1000_READ_REG(hw, E1000_DTXSWC);
- if (enable) {
- dtxswc |= (E1000_DTXSWC_MAC_SPOOF_MASK |
- E1000_DTXSWC_VLAN_SPOOF_MASK);
- /* The PF can spoof - it has to in order to
- * support emulation mode NICs */
- dtxswc ^= (1 << pf | 1 << (pf +
- E1000_DTXSWC_VLAN_SPOOF_SHIFT));
- } else {
- dtxswc &= ~(E1000_DTXSWC_MAC_SPOOF_MASK |
- E1000_DTXSWC_VLAN_SPOOF_MASK);
- }
- E1000_WRITE_REG(hw, E1000_DTXSWC, dtxswc);
+ reg_offset = E1000_DTXSWC;
break;
case e1000_i350:
- dtxswc = E1000_READ_REG(hw, E1000_TXSWC);
- if (enable) {
- dtxswc |= (E1000_DTXSWC_MAC_SPOOF_MASK |
- E1000_DTXSWC_VLAN_SPOOF_MASK);
- /* The PF can spoof - it has to in order to
- * support emulation mode NICs
- */
- dtxswc ^= (1 << pf | 1 << (pf +
- E1000_DTXSWC_VLAN_SPOOF_SHIFT));
- } else {
- dtxswc &= ~(E1000_DTXSWC_MAC_SPOOF_MASK |
- E1000_DTXSWC_VLAN_SPOOF_MASK);
- }
- E1000_WRITE_REG(hw, E1000_TXSWC, dtxswc);
- default:
+ case e1000_i354:
+ reg_offset = E1000_TXSWC;
break;
+ default:
+ return;
}
+
+ reg_val = E1000_READ_REG(hw, reg_offset);
+ if (enable) {
+ reg_val |= (E1000_DTXSWC_MAC_SPOOF_MASK |
+ E1000_DTXSWC_VLAN_SPOOF_MASK);
+ /* The PF can spoof - it has to in order to
+ * support emulation mode NICs
+ */
+ reg_val ^= (1 << pf | 1 << (pf + MAX_NUM_VFS));
+ } else {
+ reg_val &= ~(E1000_DTXSWC_MAC_SPOOF_MASK |
+ E1000_DTXSWC_VLAN_SPOOF_MASK);
+ }
+ E1000_WRITE_REG(hw, reg_offset, reg_val);
}
/**
E1000_WRITE_REG(hw, E1000_DTXSWC, dtxswc);
break;
case e1000_i350:
+ case e1000_i354:
dtxswc = E1000_READ_REG(hw, E1000_TXSWC);
if (enable)
dtxswc |= E1000_DTXSWC_VMDQ_LOOPBACK_EN;
hw->dev_spec._82575.global_device_reset = false;
+ /* 82580 does not reliably do global_device_reset due to hw errata */
+ if (hw->mac.type == e1000_82580)
+ global_device_reset = false;
+
/* Get current control state. */
ctrl = E1000_READ_REG(hw, E1000_CTRL);
DEBUGOUT("Auto Read Done did not complete\n");
}
- /* If EEPROM is not present, run manual init scripts */
- if (!(E1000_READ_REG(hw, E1000_EECD) & E1000_EECD_PRES))
- e1000_reset_init_script_82575(hw);
-
/* clear global device reset status bit */
E1000_WRITE_REG(hw, E1000_STATUS, E1000_STAT_DEV_RST_SET);
**/
STATIC s32 e1000_validate_nvm_checksum_82580(struct e1000_hw *hw)
{
- s32 ret_val = E1000_SUCCESS;
+ s32 ret_val;
u16 eeprom_regions_count = 1;
u16 j, nvm_data;
u16 nvm_offset;
return ret_val;
}
+/**
+ * __e1000_access_emi_reg - Read/write EMI register
+ * @hw: pointer to the HW structure
+ * @addr: EMI address to program
+ * @data: pointer to value to read/write from/to the EMI address
+ * @read: boolean flag to indicate read or write
+ **/
+STATIC s32 __e1000_access_emi_reg(struct e1000_hw *hw, u16 address,
+ u16 *data, bool read)
+{
+ s32 ret_val;
+
+ DEBUGFUNC("__e1000_access_emi_reg");
+
+ ret_val = hw->phy.ops.write_reg(hw, E1000_EMIADD, address);
+ if (ret_val)
+ return ret_val;
+
+ if (read)
+ ret_val = hw->phy.ops.read_reg(hw, E1000_EMIDATA, data);
+ else
+ ret_val = hw->phy.ops.write_reg(hw, E1000_EMIDATA, *data);
+
+ return ret_val;
+}
+
+/**
+ * e1000_read_emi_reg - Read Extended Management Interface register
+ * @hw: pointer to the HW structure
+ * @addr: EMI address to program
+ * @data: value to be read from the EMI address
+ **/
+s32 e1000_read_emi_reg(struct e1000_hw *hw, u16 addr, u16 *data)
+{
+ DEBUGFUNC("e1000_read_emi_reg");
+
+ return __e1000_access_emi_reg(hw, addr, data, true);
+}
+
+/**
+ * e1000_initialize_M88E1512_phy - Initialize M88E1512 PHY
+ * @hw: pointer to the HW structure
+ *
+ * Initialize Marverl 1512 to work correctly with Avoton.
+ **/
+s32 e1000_initialize_M88E1512_phy(struct e1000_hw *hw)
+{
+ struct e1000_phy_info *phy = &hw->phy;
+ s32 ret_val = E1000_SUCCESS;
+
+ DEBUGFUNC("e1000_initialize_M88E1512_phy");
+
+ /* Check if this is correct PHY. */
+ if (phy->id != M88E1512_E_PHY_ID)
+ goto out;
+
+ /* Switch to PHY page 0xFF. */
+ ret_val = phy->ops.write_reg(hw, E1000_M88E1543_PAGE_ADDR, 0x00FF);
+ if (ret_val)
+ goto out;
+
+ ret_val = phy->ops.write_reg(hw, E1000_M88E1512_CFG_REG_2, 0x214B);
+ if (ret_val)
+ goto out;
+
+ ret_val = phy->ops.write_reg(hw, E1000_M88E1512_CFG_REG_1, 0x2144);
+ if (ret_val)
+ goto out;
+
+ ret_val = phy->ops.write_reg(hw, E1000_M88E1512_CFG_REG_2, 0x0C28);
+ if (ret_val)
+ goto out;
+
+ ret_val = phy->ops.write_reg(hw, E1000_M88E1512_CFG_REG_1, 0x2146);
+ if (ret_val)
+ goto out;
+
+ ret_val = phy->ops.write_reg(hw, E1000_M88E1512_CFG_REG_2, 0xB233);
+ if (ret_val)
+ goto out;
+
+ ret_val = phy->ops.write_reg(hw, E1000_M88E1512_CFG_REG_1, 0x214D);
+ if (ret_val)
+ goto out;
+
+ ret_val = phy->ops.write_reg(hw, E1000_M88E1512_CFG_REG_2, 0xCC0C);
+ if (ret_val)
+ goto out;
+
+ ret_val = phy->ops.write_reg(hw, E1000_M88E1512_CFG_REG_1, 0x2159);
+ if (ret_val)
+ goto out;
+
+ /* Switch to PHY page 0xFB. */
+ ret_val = phy->ops.write_reg(hw, E1000_M88E1543_PAGE_ADDR, 0x00FB);
+ if (ret_val)
+ goto out;
+
+ ret_val = phy->ops.write_reg(hw, E1000_M88E1512_CFG_REG_3, 0x000D);
+ if (ret_val)
+ goto out;
+
+ /* Switch to PHY page 0x12. */
+ ret_val = phy->ops.write_reg(hw, E1000_M88E1543_PAGE_ADDR, 0x12);
+ if (ret_val)
+ goto out;
+
+ /* Change mode to SGMII-to-Copper */
+ ret_val = phy->ops.write_reg(hw, E1000_M88E1512_MODE, 0x8001);
+ if (ret_val)
+ goto out;
+
+ /* Return the PHY to page 0. */
+ ret_val = phy->ops.write_reg(hw, E1000_M88E1543_PAGE_ADDR, 0);
+ if (ret_val)
+ goto out;
+
+ ret_val = phy->ops.commit(hw);
+ if (ret_val) {
+ DEBUGOUT("Error committing the PHY changes\n");
+ return ret_val;
+ }
+
+ msec_delay(1000);
+out:
+ return ret_val;
+}
+
/**
* e1000_set_eee_i350 - Enable/disable EEE support
* @hw: pointer to the HW structure
return ret_val;
}
+/**
+ * e1000_set_eee_i354 - Enable/disable EEE support
+ * @hw: pointer to the HW structure
+ *
+ * Enable/disable EEE legacy mode based on setting in dev_spec structure.
+ *
+ **/
+s32 e1000_set_eee_i354(struct e1000_hw *hw)
+{
+ struct e1000_phy_info *phy = &hw->phy;
+ s32 ret_val = E1000_SUCCESS;
+ u16 phy_data;
+
+ DEBUGFUNC("e1000_set_eee_i354");
+
+ if ((hw->phy.media_type != e1000_media_type_copper) ||
+ ((phy->id != M88E1543_E_PHY_ID) &&
+ (phy->id != M88E1512_E_PHY_ID)))
+ goto out;
+
+ if (!hw->dev_spec._82575.eee_disable) {
+ /* Switch to PHY page 18. */
+ ret_val = phy->ops.write_reg(hw, E1000_M88E1543_PAGE_ADDR, 18);
+ if (ret_val)
+ goto out;
+
+ ret_val = phy->ops.read_reg(hw, E1000_M88E1543_EEE_CTRL_1,
+ &phy_data);
+ if (ret_val)
+ goto out;
+
+ phy_data |= E1000_M88E1543_EEE_CTRL_1_MS;
+ ret_val = phy->ops.write_reg(hw, E1000_M88E1543_EEE_CTRL_1,
+ phy_data);
+ if (ret_val)
+ goto out;
+
+ /* Return the PHY to page 0. */
+ ret_val = phy->ops.write_reg(hw, E1000_M88E1543_PAGE_ADDR, 0);
+ if (ret_val)
+ goto out;
+
+ /* Turn on EEE advertisement. */
+ ret_val = e1000_read_xmdio_reg(hw, E1000_EEE_ADV_ADDR_I354,
+ E1000_EEE_ADV_DEV_I354,
+ &phy_data);
+ if (ret_val)
+ goto out;
+
+ phy_data |= E1000_EEE_ADV_100_SUPPORTED |
+ E1000_EEE_ADV_1000_SUPPORTED;
+ ret_val = e1000_write_xmdio_reg(hw, E1000_EEE_ADV_ADDR_I354,
+ E1000_EEE_ADV_DEV_I354,
+ phy_data);
+ } else {
+ /* Turn off EEE advertisement. */
+ ret_val = e1000_read_xmdio_reg(hw, E1000_EEE_ADV_ADDR_I354,
+ E1000_EEE_ADV_DEV_I354,
+ &phy_data);
+ if (ret_val)
+ goto out;
+
+ phy_data &= ~(E1000_EEE_ADV_100_SUPPORTED |
+ E1000_EEE_ADV_1000_SUPPORTED);
+ ret_val = e1000_write_xmdio_reg(hw, E1000_EEE_ADV_ADDR_I354,
+ E1000_EEE_ADV_DEV_I354,
+ phy_data);
+ }
+
+out:
+ return ret_val;
+}
+
+/**
+ * e1000_get_eee_status_i354 - Get EEE status
+ * @hw: pointer to the HW structure
+ * @status: EEE status
+ *
+ * Get EEE status by guessing based on whether Tx or Rx LPI indications have
+ * been received.
+ **/
+s32 e1000_get_eee_status_i354(struct e1000_hw *hw, bool *status)
+{
+ struct e1000_phy_info *phy = &hw->phy;
+ s32 ret_val = E1000_SUCCESS;
+ u16 phy_data;
+
+ DEBUGFUNC("e1000_get_eee_status_i354");
+
+ /* Check if EEE is supported on this device. */
+ if ((hw->phy.media_type != e1000_media_type_copper) ||
+ ((phy->id != M88E1543_E_PHY_ID) &&
+ (phy->id != M88E1512_E_PHY_ID)))
+ goto out;
+
+ ret_val = e1000_read_xmdio_reg(hw, E1000_PCS_STATUS_ADDR_I354,
+ E1000_PCS_STATUS_DEV_I354,
+ &phy_data);
+ if (ret_val)
+ goto out;
+
+ *status = phy_data & (E1000_PCS_STATUS_TX_LPI_RCVD |
+ E1000_PCS_STATUS_RX_LPI_RCVD) ? true : false;
+
+out:
+ return ret_val;
+}
+
/* Due to a hw errata, if the host tries to configure the VFTA register
* while performing queries from the BMC or DMA, then the VFTA in some
* cases won't be written.