ethdev: complete closing of port

After closing a port, it cannot be restarted.
So there is no reason to not free all associated resources.

The last step was done with rte_eth_dev_detach() which is deprecated.
Instead of blindly removing the associated rte_device, the driver should
check if no more port (ethdev, cryptodev, etc) is open for the device.

The last ethdev freeing which were done by rte_eth_dev_detach(),
are now done at the end of rte_eth_dev_close() if the driver supports
the flag RTE_ETH_DEV_CLOSE_REMOVE.
There will be a transition period for PMDs to enable this new flag
and migrate to the new behaviour.
When enabling RTE_ETH_DEV_CLOSE_REMOVE, the PMD must free all its
private resources for the port, in its dev_close function.
It is advised to call the dev_close function in the remove function
in order to support removing a device without closing its ports.

Some drivers does not allocate MAC addresses dynamically or separately.
In those cases, the pointer is set to NULL, in order to avoid wrongly
freeing them in rte_eth_dev_release_port().

A closed port will have the state RTE_ETH_DEV_UNUSED which is
considered as invalid by rte_eth_dev_is_valid_port().
So validity is not checked anymore for closed ports in testpmd.

Signed-off-by: Thomas Monjalon <thomas@monjalon.net>
Reviewed-by: Andrew Rybchenko <arybchenko@solarflare.com>

diff --git a/app/test-pmd/testpmd.c b/app/test-pmd/testpmd.c
index 8956d8e..eea6df0 100644 (file)
--- a/app/test-pmd/testpmd.c
+++ b/app/test-pmd/testpmd.c
@@ -1950,18 +1950,6 @@ port_is_started(portid_t port_id)
        return 1;
 }
 
-static int
-port_is_closed(portid_t port_id)
-{
-       if (port_id_is_invalid(port_id, ENABLED_WARN))
-               return 0;
-
-       if (ports[port_id].port_status != RTE_PORT_CLOSED)
-               return 0;
-
-       return 1;
-}
-
 int
 start_port(portid_t pid)
 {
@@ -2265,6 +2253,8 @@ close_port(portid_t pid)
                        port_flow_flush(pi);
                rte_eth_dev_close(pi);
 
+               remove_unused_fwd_ports();
+
                if (rte_atomic16_cmpset(&(port->port_status),
                        RTE_PORT_HANDLING, RTE_PORT_CLOSED) == 0)
                        printf("Port %d cannot be set to closed\n", pi);
@@ -2355,7 +2345,7 @@ detach_port(portid_t port_id)
 
        printf("Detaching a port...\n");
 
-       if (!port_is_closed(port_id)) {
+       if (ports[port_id].port_status != RTE_PORT_CLOSED) {
                if (ports[port_id].port_status != RTE_PORT_STOPPED) {
                        printf("Port not stopped\n");
                        return;

diff --git a/doc/guides/rel_notes/release_18_11.rst b/doc/guides/rel_notes/release_18_11.rst
index d7655d3..7163a3e 100644 (file)
--- a/doc/guides/rel_notes/release_18_11.rst
+++ b/doc/guides/rel_notes/release_18_11.rst
@@ -309,6 +309,11 @@ API Changes
   functions were deprecated since 17.05 and are replaced by
   ``rte_mbuf_raw_free()`` and ``rte_pktmbuf_prefree_seg()``.
 
+* ethdev: A call to ``rte_eth_dev_release_port()`` has been added in
+  ``rte_eth_dev_close()``. As a consequence, a closed port is freed
+  and seen as invalid because of its state ``RTE_ETH_DEV_UNUSED``.
+  This new behaviour is enabled per driver for a migration period.
+
 * A new device flag, RTE_ETH_DEV_NOLIVE_MAC_ADDR, changes the order of
   actions inside rte_eth_dev_start regarding MAC set. Some NICs do not
   support MAC changes once the port has started and with this new device

diff --git a/lib/librte_ethdev/rte_ethdev.c b/lib/librte_ethdev/rte_ethdev.c
index 178800a..0979c0c 100644 (file)
--- a/lib/librte_ethdev/rte_ethdev.c
+++ b/lib/librte_ethdev/rte_ethdev.c
@@ -1384,6 +1384,16 @@ rte_eth_dev_close(uint16_t port_id)
        dev->data->dev_started = 0;
        (*dev->dev_ops->dev_close)(dev);
 
+       /* check behaviour flag - temporary for PMD migration */
+       if ((dev->data->dev_flags & RTE_ETH_DEV_CLOSE_REMOVE) != 0) {
+               /* new behaviour: send event + reset state + free all data */
+               rte_eth_dev_release_port(dev);
+               return;
+       }
+       RTE_ETHDEV_LOG(DEBUG, "Port closing is using an old behaviour.\n"
+                       "The driver %s should migrate to the new behaviour.\n",
+                       dev->device->driver->name);
+       /* old behaviour: only free queue arrays */
        dev->data->nb_rx_queues = 0;
        rte_free(dev->data->rx_queues);
        dev->data->rx_queues = NULL;

diff --git a/lib/librte_ethdev/rte_ethdev.h b/lib/librte_ethdev/rte_ethdev.h
index fb40c89..c4caf06 100644 (file)
--- a/lib/librte_ethdev/rte_ethdev.h
+++ b/lib/librte_ethdev/rte_ethdev.h
@@ -1259,6 +1259,11 @@ struct rte_eth_dev_owner {
        char name[RTE_ETH_MAX_OWNER_NAME_LEN]; /**< The owner name. */
 };
 
+/**
+ * Port is released (i.e. totally freed and data erased) on close.
+ * Temporary flag for PMD migration to new rte_eth_dev_close() behaviour.
+ */
+#define RTE_ETH_DEV_CLOSE_REMOVE 0x0001
 /** Device supports link state interrupt */
 #define RTE_ETH_DEV_INTR_LSC     0x0002
 /** Device is a bonded slave */
@@ -1802,8 +1807,8 @@ int rte_eth_dev_set_link_down(uint16_t port_id);
 
 /**
  * Close a stopped Ethernet device. The device cannot be restarted!
- * The function frees all resources except for needed by the
- * closed state. To free these resources, call rte_eth_dev_detach().
+ * The function frees all port resources if the driver supports
+ * the flag RTE_ETH_DEV_CLOSE_REMOVE.
  *
  * @param port_id
  *   The port identifier of the Ethernet device.