doc: refer PMD compile/test section from nfp guide

Refer the section which explains driver compilation and running of
testpmd in Linux, instead of describing it in driver documentation.

Signed-off-by: Shijith Thotton <shijith.thotton@caviumnetworks.com>
Acked-by: John McNamara <john.mcnamara@intel.com>

diff --git a/doc/guides/nics/nfp.rst b/doc/guides/nics/nfp.rst
index b643e5b..c732fb1 100644 (file)
--- a/doc/guides/nics/nfp.rst
+++ b/doc/guides/nics/nfp.rst
@@ -81,85 +81,15 @@ Once DPDK is built all the DPDK apps and examples include support for
 the NFP PMD.
 
 
-System configuration
---------------------
-
-Using the NFP PMD is not different to using other PMDs. Usual steps are:
-
-#. **Configure hugepages:** All major Linux distributions have the hugepages
-   functionality enabled by default. By default this allows the system uses for
-   working with transparent hugepages. But in this case some hugepages need to
-   be created/reserved for use with the DPDK through the hugetlbfs file system.
-   First the virtual file system need to be mounted:
-
-   .. code-block:: console
-
-      mount -t hugetlbfs none /mnt/hugetlbfs
-
-   The command uses the common mount point for this file system and it needs to
-   be created if necessary.
-
-   Configuring hugepages is performed via sysfs:
-
-   .. code-block:: console
-
-      /sys/kernel/mm/hugepages/hugepages-2048kB/nr_hugepages
-
-   This sysfs file is used to specify the number of hugepages to reserve.
-   For example:
-
-   .. code-block:: console
-
-      echo 1024 > /sys/kernel/mm/hugepages/hugepages-2048kB/nr_hugepages
-
-   This will reserve 2GB of memory using 1024 2MB hugepages. The file may be
-   read to see if the operation was performed correctly:
-
-   .. code-block:: console
-
-      cat /sys/kernel/mm/hugepages/hugepages-2048kB/nr_hugepages
-
-   The number of unused hugepages may also be inspected.
-
-   Before executing the DPDK app it should match the value of nr_hugepages.
-
-   .. code-block:: console
-
-      cat /sys/kernel/mm/hugepages/hugepages-2048kB/free_hugepages
-
-   The hugepages reservation should be performed at system initialization and
-   it is usual to use a kernel parameter for configuration. If the reservation
-   is attempted on a busy system it will likely fail. Reserving memory for
-   hugepages may be done adding the following to the grub kernel command line:
-
-   .. code-block:: console
-
-      default_hugepagesz=1M hugepagesz=2M hugepages=1024
-
-   This will reserve 2GBytes of memory using 2Mbytes huge pages.
-
-   Finally, for a NUMA system the allocation needs to be made on the correct
-   NUMA node. In a DPDK app there is a master core which will (usually) perform
-   memory allocation. It is important that some of the hugepages are reserved
-   on the NUMA memory node where the network device is attached. This is because
-   of a restriction in DPDK by which TX and RX descriptors rings must be created
-   on the master code.
-
-   Per-node allocation of hugepages may be inspected and controlled using sysfs.
-   For example:
-
-   .. code-block:: console
+Driver compilation and testing
+------------------------------
 
-      cat /sys/devices/system/node/node0/hugepages/hugepages-2048kB/nr_hugepages
+Refer to the document :ref:`compiling and testing a PMD for a NIC <pmd_build_and_test>`
+for details.
 
-   For a NUMA system there will be a specific hugepage directory per node
-   allowing control of hugepage reservation. A common problem may occur when
-   hugepages reservation is performed after the system has been working for
-   some time. Configuration using the global sysfs hugepage interface will
-   succeed but the per-node allocations may be unsatisfactory.
 
-   The number of hugepages that need to be reserved depends on how the app uses
-   TX and RX descriptors, and packets mbufs.
+System configuration
+--------------------
 
 #. **Enable SR-IOV on the NFP-6xxx device:** The current NFP PMD works with
    Virtual Functions (VFs) on a NFP device. Make sure that one of the Physical
@@ -191,62 +121,3 @@ Using the NFP PMD is not different to using other PMDs. Usual steps are:
    -k option shows the device driver, if any, that devices are bound to.
    Depending on the modules loaded at this point the new PCI devices may be
    bound to nfp_netvf driver.
-
-#. **To install the uio kernel module (manually):** All major Linux
-   distributions have support for this kernel module so it is straightforward
-   to install it:
-
-   .. code-block:: console
-
-      modprobe uio
-
-   The module should now be listed by the lsmod command.
-
-#. **To install the igb_uio kernel module (manually):** This module is part
-   of DPDK sources and configured by default (CONFIG_RTE_EAL_IGB_UIO=y).
-
-   .. code-block:: console
-
-      modprobe igb_uio.ko
-
-   The module should now be listed by the lsmod command.
-
-   Depending on which NFP modules are loaded, it could be necessary to
-   detach NFP devices from the nfp_netvf module. If this is the case the
-   device needs to be unbound, for example:
-
-   .. code-block:: console
-
-      echo 0000:03:08.0 > /sys/bus/pci/devices/0000:03:08.0/driver/unbind
-
-      lspci -d19ee: -k
-
-   The output of lspci should now show that 0000:03:08.0 is not bound to
-   any driver.
-
-   The next step is to add the NFP PCI ID to the IGB UIO driver:
-
-   .. code-block:: console
-
-      echo 19ee 6003 > /sys/bus/pci/drivers/igb_uio/new_id
-
-   And then to bind the device to the igb_uio driver:
-
-   .. code-block:: console
-
-      echo 0000:03:08.0 > /sys/bus/pci/drivers/igb_uio/bind
-
-      lspci -d19ee: -k
-
-   lspci should show that device bound to igb_uio driver.
-
-#. **Using scripts to install and bind modules:** DPDK provides scripts which are
-   useful for installing the UIO modules and for binding the right device to those
-   modules avoiding doing so manually:
-
-   * **dpdk-setup.sh**
-   * **dpdk-devbind.py**
-
-   Configuration may be performed by running dpdk-setup.sh which invokes
-   dpdk-devbind.py as needed. Executing dpdk-setup.sh will display a menu of
-   configuration options.