#define IXGBE_MDIO_AUTO_NEG_CONTROL 0x0 /* AUTO_NEG Control Reg */
#define IXGBE_MDIO_AUTO_NEG_STATUS 0x1 /* AUTO_NEG Status Reg */
#define IXGBE_MDIO_AUTO_NEG_VENDOR_STAT 0xC800 /* AUTO_NEG Vendor Status Reg */
+#define IXGBE_MDIO_AUTO_NEG_VENDOR_TX_ALARM 0xCC00 /* AUTO_NEG Vendor TX Reg */
#define IXGBE_MDIO_AUTO_NEG_ADVT 0x10 /* AUTO_NEG Advt Reg */
#define IXGBE_MDIO_AUTO_NEG_LP 0x13 /* AUTO_NEG LP Status Reg */
#define IXGBE_MDIO_AUTO_NEG_EEE_ADVT 0x3C /* AUTO_NEG EEE Advt Reg */
#define IXGBE_MDIO_PHY_1000BASET_ABILITY 0x0020 /* 1000BaseT capable */
#define IXGBE_MDIO_PHY_100BASETX_ABILITY 0x0080 /* 100BaseTX capable */
#define IXGBE_MDIO_PHY_SET_LOW_POWER_MODE 0x0800 /* Set low power mode */
+#define IXGBE_AUTO_NEG_LP_STATUS 0xE820 /* AUTO NEG Rx LP Status Reg */
+#define IXGBE_AUTO_NEG_LP_1000BASE_CAP 0x8000 /* AUTO NEG Rx LP 1000BaseT Cap */
+#define IXGBE_AUTO_NEG_LP_10GBASE_CAP 0x0800 /* AUTO NEG Rx LP 10GBaseT Cap */
+#define IXGBE_AUTO_NEG_10GBASET_STAT 0x0021 /* AUTO NEG 10G BaseT Stat */
#define IXGBE_MDIO_TX_VENDOR_ALARMS_3 0xCC02 /* Vendor Alarms 3 Reg */
#define IXGBE_MDIO_TX_VENDOR_ALARMS_3_RST_MASK 0x3 /* PHY Reset Complete Mask */
#define IXGBE_MDIO_AUTO_NEG_LINK_STATUS 0x4 /* Indicates if link is up */
-#define IXGBE_MDIO_AUTO_NEG_VENDOR_STATUS_MASK 0x7 /* Speed/Duplex Mask */
+#define IXGBE_MDIO_AUTO_NEG_VENDOR_STATUS_MASK 0x7 /* Speed/Duplex Mask */
+#define IXGBE_MDIO_AUTO_NEG_VEN_STAT_SPEED_MASK 0x6 /* Speed Mask */
#define IXGBE_MDIO_AUTO_NEG_VENDOR_STATUS_10M_HALF 0x0 /* 10Mb/s Half Duplex */
#define IXGBE_MDIO_AUTO_NEG_VENDOR_STATUS_10M_FULL 0x1 /* 10Mb/s Full Duplex */
#define IXGBE_MDIO_AUTO_NEG_VENDOR_STATUS_100M_HALF 0x2 /* 100Mb/s Half Duplex */
#define IXGBE_MDIO_AUTO_NEG_VENDOR_STATUS_1GB_FULL 0x5 /* 1Gb/s Full Duplex */
#define IXGBE_MDIO_AUTO_NEG_VENDOR_STATUS_10GB_HALF 0x6 /* 10Gb/s Half Duplex */
#define IXGBE_MDIO_AUTO_NEG_VENDOR_STATUS_10GB_FULL 0x7 /* 10Gb/s Full Duplex */
+#define IXGBE_MDIO_AUTO_NEG_VENDOR_STATUS_1GB 0x4 /* 1Gb/s */
+#define IXGBE_MDIO_AUTO_NEG_VENDOR_STATUS_10GB 0x6 /* 10Gb/s */
#define IXGBE_MII_10GBASE_T_AUTONEG_CTRL_REG 0x20 /* 10G Control Reg */
#define IXGBE_MII_AUTONEG_VENDOR_PROVISION_1_REG 0xC400 /* 1G Provisioning 1 */
#define IXGBE_NVM_POLL_WRITE 1 /* Flag for polling for wr complete */
#define IXGBE_NVM_POLL_READ 0 /* Flag for polling for rd complete */
+#define NVM_INIT_CTRL_3 0x38
+#define NVM_INIT_CTRL_3_LPLU 0x8
+#define NVM_INIT_CTRL_3_D10GMP_PORT0 0x40
+#define NVM_INIT_CTRL_3_D10GMP_PORT1 0x100
+
#define IXGBE_ETH_LENGTH_OF_ADDRESS 6
#define IXGBE_EEPROM_PAGE_SIZE_MAX 128
s32 (*write_i2c_combined)(struct ixgbe_hw *, u8 addr, u16 reg, u16 val);
s32 (*check_overtemp)(struct ixgbe_hw *);
s32 (*set_phy_power)(struct ixgbe_hw *, bool on);
+ s32 (*enter_lplu)(struct ixgbe_hw *);
s32 (*read_i2c_combined_unlocked)(struct ixgbe_hw *, u8 addr, u16 reg,
u16 *value);
s32 (*write_i2c_combined_unlocked)(struct ixgbe_hw *, u8 addr, u16 reg,
u16 word_size;
u16 address_bits;
u16 word_page_size;
+ u16 ctrl_word_3;
};
#define IXGBE_FLAGS_DOUBLE_RESET_REQUIRED 0x01
break;
case ixgbe_phy_x550em_ext_t:
phy->ops.setup_internal_link = ixgbe_setup_internal_phy_x550em;
+ phy->ops.enter_lplu = ixgbe_enter_lplu_t_x550em;
break;
default:
break;
}
}
}
+
+/**
+ * ixgbe_enter_lplu_x550em - Transition to low power states
+ * @hw: pointer to hardware structure
+ *
+ * Configures Low Power Link Up on transition to low power states
+ * (from D0 to non-D0). Link is required to enter LPLU so avoid resetting the
+ * X557 PHY immediately prior to entering LPLU.
+ **/
+s32 ixgbe_enter_lplu_t_x550em(struct ixgbe_hw *hw)
+{
+ u16 autoneg_status, an_10g_cntl_reg, autoneg_reg, speed;
+ s32 status;
+ ixgbe_link_speed lcd_speed;
+
+ /* If blocked by MNG FW, then don't restart AN */
+ if (ixgbe_check_reset_blocked(hw))
+ return IXGBE_SUCCESS;
+
+ status = hw->phy.ops.read_reg(hw, IXGBE_MDIO_AUTO_NEG_STATUS,
+ IXGBE_MDIO_AUTO_NEG_DEV_TYPE,
+ &autoneg_status);
+
+ if (status != IXGBE_SUCCESS)
+ return status;
+
+ status = ixgbe_read_eeprom(hw, NVM_INIT_CTRL_3, &hw->eeprom.ctrl_word_3);
+
+ if (status != IXGBE_SUCCESS)
+ return status;
+
+ /* If link is down, LPLU disabled in NVM, WoL disabled, or manageability
+ * disabled, then force link down by entering low power mode.
+ */
+ if (!(autoneg_status & IXGBE_MDIO_AUTO_NEG_LINK_STATUS) ||
+ !(hw->eeprom.ctrl_word_3 & NVM_INIT_CTRL_3_LPLU) ||
+ !(hw->wol_enabled || ixgbe_mng_present(hw)))
+ return ixgbe_set_copper_phy_power(hw, FALSE);
+
+ /* Determine LCD */
+ status = ixgbe_get_lcd_t_x550em(hw, &lcd_speed);
+
+ if (status != IXGBE_SUCCESS)
+ return status;
+
+ /* If no valid LCD link speed, then force link down and exit. */
+ if (lcd_speed == IXGBE_LINK_SPEED_UNKNOWN)
+ return ixgbe_set_copper_phy_power(hw, FALSE);
+
+ status = hw->phy.ops.read_reg(hw, IXGBE_MDIO_AUTO_NEG_VENDOR_STAT,
+ IXGBE_MDIO_AUTO_NEG_DEV_TYPE,
+ &speed);
+
+ if (status != IXGBE_SUCCESS)
+ return status;
+
+ /* clear everything but the speed bits */
+ speed &= IXGBE_MDIO_AUTO_NEG_VEN_STAT_SPEED_MASK;
+
+ /* If current speed is already LCD, then exit. */
+ if (((speed == IXGBE_MDIO_AUTO_NEG_VENDOR_STATUS_1GB) &&
+ (lcd_speed == IXGBE_LINK_SPEED_1GB_FULL)) ||
+ ((speed == IXGBE_MDIO_AUTO_NEG_VENDOR_STATUS_10GB) &&
+ (lcd_speed == IXGBE_LINK_SPEED_10GB_FULL)))
+ return status;
+
+ /* Clear AN completed indication */
+ status = hw->phy.ops.read_reg(hw, IXGBE_MDIO_AUTO_NEG_VENDOR_TX_ALARM,
+ IXGBE_MDIO_AUTO_NEG_DEV_TYPE,
+ &autoneg_status);
+
+ if (status != IXGBE_SUCCESS)
+ return status;
+
+ status = hw->phy.ops.read_reg(hw, IXGBE_MII_10GBASE_T_AUTONEG_CTRL_REG,
+ IXGBE_MDIO_AUTO_NEG_DEV_TYPE,
+ &an_10g_cntl_reg);
+
+ if (status != IXGBE_SUCCESS)
+ return status;
+
+ status = hw->phy.ops.read_reg(hw,
+ IXGBE_MII_AUTONEG_VENDOR_PROVISION_1_REG,
+ IXGBE_MDIO_AUTO_NEG_DEV_TYPE,
+ &autoneg_reg);
+
+ if (status != IXGBE_SUCCESS)
+ return status;
+
+ /* Set AN advertizement to only include LCD */
+ if (lcd_speed == IXGBE_LINK_SPEED_1GB_FULL) {
+ an_10g_cntl_reg &= ~IXGBE_MII_10GBASE_T_ADVERTISE;
+ autoneg_reg |= IXGBE_MII_1GBASE_T_ADVERTISE;
+ }
+
+ if (lcd_speed == IXGBE_LINK_SPEED_10GB_FULL) {
+ an_10g_cntl_reg |= IXGBE_MII_10GBASE_T_ADVERTISE;
+ autoneg_reg &= ~IXGBE_MII_1GBASE_T_ADVERTISE;
+ }
+
+ status = hw->phy.ops.write_reg(hw, IXGBE_MII_10GBASE_T_AUTONEG_CTRL_REG,
+ IXGBE_MDIO_AUTO_NEG_DEV_TYPE,
+ an_10g_cntl_reg);
+
+ if (status != IXGBE_SUCCESS)
+ return status;
+
+ status = hw->phy.ops.write_reg(hw,
+ IXGBE_MII_AUTONEG_VENDOR_PROVISION_1_REG,
+ IXGBE_MDIO_AUTO_NEG_DEV_TYPE,
+ autoneg_reg);
+
+ if (status != IXGBE_SUCCESS)
+ return status;
+
+ /* Restart PHY auto-negotiation. */
+ status = hw->phy.ops.read_reg(hw, IXGBE_MDIO_AUTO_NEG_CONTROL,
+ IXGBE_MDIO_AUTO_NEG_DEV_TYPE, &autoneg_reg);
+
+ if (status != IXGBE_SUCCESS)
+ return status;
+
+ autoneg_reg |= IXGBE_MII_RESTART;
+
+ status = hw->phy.ops.write_reg(hw, IXGBE_MDIO_AUTO_NEG_CONTROL,
+ IXGBE_MDIO_AUTO_NEG_DEV_TYPE, autoneg_reg);
+
+ if (status != IXGBE_SUCCESS)
+ return status;
+
+ status = ixgbe_setup_ixfi_x550em(hw, &lcd_speed);
+
+ return status;
+}
+
+/**
+ * ixgbe_get_lcd_x550em - Determine lowest common denominator
+ * @hw: pointer to hardware structure
+ * @lcd_speed: pointer to lowest common link speed
+ *
+ * Determine lowest common link speed with link partner.
+ **/
+s32 ixgbe_get_lcd_t_x550em(struct ixgbe_hw *hw, ixgbe_link_speed *lcd_speed)
+{
+ u16 an_lp_status;
+ s32 status;
+ u16 word = hw->eeprom.ctrl_word_3;
+
+ *lcd_speed = IXGBE_LINK_SPEED_UNKNOWN;
+
+ status = hw->phy.ops.read_reg(hw, IXGBE_AUTO_NEG_LP_STATUS,
+ IXGBE_MDIO_AUTO_NEG_DEV_TYPE,
+ &an_lp_status);
+
+ if (status != IXGBE_SUCCESS)
+ return status;
+
+ /* If link partner advertised 1G, return 1G */
+ if (an_lp_status & IXGBE_AUTO_NEG_LP_1000BASE_CAP) {
+ *lcd_speed = IXGBE_LINK_SPEED_1GB_FULL;
+ return status;
+ }
+
+ /* If 10G disabled for LPLU via NVM D10GMP, then return no valid LCD */
+ if ((hw->bus.lan_id && (word & NVM_INIT_CTRL_3_D10GMP_PORT1)) ||
+ (word & NVM_INIT_CTRL_3_D10GMP_PORT0))
+ return status;
+
+ /* Link partner not capable of lower speeds, return 10G */
+ *lcd_speed = IXGBE_LINK_SPEED_10GB_FULL;
+ return status;
+}
git.droids-corp.org / dpdk.git / commitdiff