ixgbe: link up and down

It is implemented by enabling or disabling TX laser.

Signed-off-by: Ouyang Changchun <changchun.ouyang@intel.com>
Tested-by: Waterman Cao <waterman.cao@intel.com>
Acked by: Ivan Boule <ivan.boule@6wind.com>

diff --git a/lib/librte_pmd_ixgbe/ixgbe_ethdev.c b/lib/librte_pmd_ixgbe/ixgbe_ethdev.c
index eb31bd9..eab4ba8 100644 (file)
--- a/lib/librte_pmd_ixgbe/ixgbe_ethdev.c
+++ b/lib/librte_pmd_ixgbe/ixgbe_ethdev.c
@@ -98,6 +98,8 @@ static int eth_ixgbe_dev_init(struct eth_driver *eth_drv,
 static int  ixgbe_dev_configure(struct rte_eth_dev *dev);
 static int  ixgbe_dev_start(struct rte_eth_dev *dev);
 static void ixgbe_dev_stop(struct rte_eth_dev *dev);
+static int  ixgbe_dev_set_link_up(struct rte_eth_dev *dev);
+static int  ixgbe_dev_set_link_down(struct rte_eth_dev *dev);
 static void ixgbe_dev_close(struct rte_eth_dev *dev);
 static void ixgbe_dev_promiscuous_enable(struct rte_eth_dev *dev);
 static void ixgbe_dev_promiscuous_disable(struct rte_eth_dev *dev);
@@ -252,6 +254,8 @@ static struct eth_dev_ops ixgbe_eth_dev_ops = {
        .dev_configure        = ixgbe_dev_configure,
        .dev_start            = ixgbe_dev_start,
        .dev_stop             = ixgbe_dev_stop,
+       .dev_set_link_up    = ixgbe_dev_set_link_up,
+       .dev_set_link_down  = ixgbe_dev_set_link_down,
        .dev_close            = ixgbe_dev_close,
        .promiscuous_enable   = ixgbe_dev_promiscuous_enable,
        .promiscuous_disable  = ixgbe_dev_promiscuous_disable,
@@ -1524,6 +1528,65 @@ ixgbe_dev_stop(struct rte_eth_dev *dev)
        rte_ixgbe_dev_atomic_write_link_status(dev, &link);
 }
 
+/*
+ * Set device link up: enable tx laser.
+ */
+static int
+ixgbe_dev_set_link_up(struct rte_eth_dev *dev)
+{
+       struct ixgbe_hw *hw =
+               IXGBE_DEV_PRIVATE_TO_HW(dev->data->dev_private);
+       if (hw->mac.type == ixgbe_mac_82599EB) {
+#ifdef RTE_NIC_BYPASS
+               if (hw->device_id == IXGBE_DEV_ID_82599_BYPASS) {
+                       /* Not suported in bypass mode */
+                       PMD_INIT_LOG(ERR,
+                               "\nSet link up is not supported "
+                               "by device id 0x%x\n",
+                               hw->device_id);
+                       return -ENOTSUP;
+               }
+#endif
+               /* Turn on the laser */
+               ixgbe_enable_tx_laser(hw);
+               return 0;
+       }
+
+       PMD_INIT_LOG(ERR, "\nSet link up is not supported by device id 0x%x\n",
+               hw->device_id);
+       return -ENOTSUP;
+}
+
+/*
+ * Set device link down: disable tx laser.
+ */
+static int
+ixgbe_dev_set_link_down(struct rte_eth_dev *dev)
+{
+       struct ixgbe_hw *hw =
+               IXGBE_DEV_PRIVATE_TO_HW(dev->data->dev_private);
+       if (hw->mac.type == ixgbe_mac_82599EB) {
+#ifdef RTE_NIC_BYPASS
+               if (hw->device_id == IXGBE_DEV_ID_82599_BYPASS) {
+                       /* Not suported in bypass mode */
+                       PMD_INIT_LOG(ERR,
+                               "\nSet link down is not supported "
+                               "by device id 0x%x\n",
+                                hw->device_id);
+                       return -ENOTSUP;
+               }
+#endif
+               /* Turn off the laser */
+               ixgbe_disable_tx_laser(hw);
+               return 0;
+       }
+
+       PMD_INIT_LOG(ERR,
+               "\nSet link down is not supported by device id 0x%x\n",
+                hw->device_id);
+       return -ENOTSUP;
+}
+
 /*
  * Reest and stop device.
  */