Beilei Xing [Thu, 23 Jun 2016 07:22:27 +0000 (15:22 +0800)]
net/ixgbe/base: fix register access error
This patch corrects the FLA/GSCL/GSCN access offset values according
to the datasheet.
Fixes:
0790adeb5675 ("ixgbe/base: support X550em_a device")
Signed-off-by: Beilei Xing <beilei.xing@intel.com>
Beilei Xing [Thu, 23 Jun 2016 07:22:26 +0000 (15:22 +0800)]
net/ixgbe/base: fix race condition between ports
This patch fixes a possible race issue between ports, when issuing host
interface commands, by acquiring/releasing the management host interface
semaphore in ixgbe_host_interface_command.
Fixes:
36f43e8679ae ("ixgbe/base: refactor manageability block communication")
Signed-off-by: Beilei Xing <beilei.xing@intel.com>
Beilei Xing [Thu, 23 Jun 2016 07:22:25 +0000 (15:22 +0800)]
net/ixgbe/base: add function to reset swfw semaphore
For X540 onwards it is possible if a system reset occurs at the
right time to leave the SWFW semaphore high. This new function will
attempt to grab and release the semaphore. If the grab times out it
will still release the semaphore placing it in a known good state.
The idea is to call this when you know no one should be holding the
semaphore (i.e. probe time)
Signed-off-by: Beilei Xing <beilei.xing@intel.com>
Beilei Xing [Thu, 23 Jun 2016 07:22:24 +0000 (15:22 +0800)]
net/ixgbe/base: update device IDs
There are two device IDs changed from 15C6/15C7 to 15E4/15E5 because of
PHY info changes. 15C6/15C7 IDs are now used for the backplane
SGMII versions.
Also, clean up some discovery kludges from the previous shared ID,
and also add 15C6/15C7 to ixgbe_set_mdio_speed just for paranoia
to control MDIO speed even though nothing should be attached.
Signed-off-by: Beilei Xing <beilei.xing@intel.com>
Beilei Xing [Thu, 23 Jun 2016 07:22:23 +0000 (15:22 +0800)]
net/ixgbe/base: support new PHY types
This patch adds new phy definitions and support functions to enable those
new phy types.
Signed-off-by: Beilei Xing <beilei.xing@intel.com>
Beilei Xing [Thu, 23 Jun 2016 07:22:22 +0000 (15:22 +0800)]
net/ixgbe/base: refactor internal PHY mode determination
NW_MNG_IF_SEL register is a PHY link configuration register.
Add ixgbe_read_mng_if_sel_x550em to read NW_MNG_IF_SEL, validate
register values and save fields such as PHY MDIO address. This
centralises the reading and checking of the register in one place
Signed-off-by: Beilei Xing <beilei.xing@intel.com>
Beilei Xing [Thu, 23 Jun 2016 07:22:21 +0000 (15:22 +0800)]
net/ixgbe/base: rename header guard
The ixgbe_vf.h file did not use _<FILENAME>_ and instead used
__<FILENAME>__ which is not the standard used in every other file.
Fixes:
af75078fece3 ("first public release")
Signed-off-by: Beilei Xing <beilei.xing@intel.com>
Beilei Xing [Thu, 23 Jun 2016 07:22:20 +0000 (15:22 +0800)]
net/ixgbe/base: fix error path to release lock
When there is an error getting the PHY token, the error path
fails to release the locks that it has taken. Release those
locks in that failure case.
Fixes:
86b8fb293fdf ("ixgbe/base: add sw-firmware sync for resource sharing on X550em_a")
Signed-off-by: Beilei Xing <beilei.xing@intel.com>
Beilei Xing [Thu, 23 Jun 2016 07:22:19 +0000 (15:22 +0800)]
net/ixgbe/base: fix macro name
This patch renames IXGBE_PVFTTDLEN to IXGBE_PVFTDLEN according to
abbreviation of Transmit Descriptor Length in datasheet.
Fixes:
d2e72774e58c ("ixgbe/base: support X550")
Signed-off-by: Beilei Xing <beilei.xing@intel.com>
Beilei Xing [Thu, 23 Jun 2016 07:22:18 +0000 (15:22 +0800)]
net/ixgbe/base: clear stale VMDq pool mappings
This patch adds clearing the pool mappings when configuring default
MAC addresses for the interface. Without this there will be the risk
of leaking an address into pool 0 which really belongs to VF 0 when
SR-IOV is enabled.
Signed-off-by: Beilei Xing <beilei.xing@intel.com>
Beilei Xing [Thu, 23 Jun 2016 07:22:17 +0000 (15:22 +0800)]
net/ixgbe/base: add link MAC setup for X550a SFP+
This patch updates ixgbe_setup_mac_link_sfp_x550a for X550 SFP+.
ixgbe_set_lan_id_multi_port_pcie has been updated to set the MAC
instance(0/1) which is needed when configuring the external PHY,
since X550a has two instances of MGPK. The MAC instance is read
from the EEPROM.
Signed-off-by: Beilei Xing <beilei.xing@intel.com>
Beilei Xing [Thu, 23 Jun 2016 07:22:16 +0000 (15:22 +0800)]
net/ixgbe/base: allow per-device-type method calls
Use the method pointers instead of direct function calls for IOSF
access so that the right functions can be called on X550EM_a,
compared to other devices using the driver.
Signed-off-by: Beilei Xing <beilei.xing@intel.com>
Beilei Xing [Thu, 23 Jun 2016 07:22:15 +0000 (15:22 +0800)]
net/ixgbe/base: add KR support for X550em_a devices
Signed-off-by: Beilei Xing <beilei.xing@intel.com>
Beilei Xing [Thu, 23 Jun 2016 07:22:14 +0000 (15:22 +0800)]
net/ixgbe/base: refactor EEE setup for X550
Break ixgbe_setup_eee_X550 down to better handle a change from if
statements to switch statements needed to add X550em_a KR support.
Signed-off-by: Beilei Xing <beilei.xing@intel.com>
Beilei Xing [Thu, 23 Jun 2016 07:22:13 +0000 (15:22 +0800)]
net/ixgbe/base: fix firmware command checksum error
When software sends commands to firmware using the host
slave command interface, firmware fails to receive the
command due to a checksum failed error, as the checksum is
not being correctly set by the driver software.
This patch sets command checksum to the default value of
0xFF, as per the datasheet, therefore the checksum won't
be checked by firmware.
Fixes:
86b8fb293fdf ("ixgbe/base: add sw-firmware sync for resource sharing on X550em_a")
Fixes:
0790adeb5675 ("ixgbe/base: support X550em_a device")
Signed-off-by: Beilei Xing <beilei.xing@intel.com>
Beilei Xing [Thu, 23 Jun 2016 07:22:12 +0000 (15:22 +0800)]
net/ixgbe/base: add MAC link setup for X550a SFP
This patch adds ixgbe_setup_mac_link_sfp_x550a for X550a SFP.
Signed-off-by: Beilei Xing <beilei.xing@intel.com>
Beilei Xing [Thu, 23 Jun 2016 07:22:11 +0000 (15:22 +0800)]
net/ixgbe/base: return error on VF MAC address failure
An error code indicating that the PF rejects the MAC address change
should be returned, in case that the PF has already assigned a MAC
for the VF.
Fixes:
af75078fece3 ("first public release")
Signed-off-by: Beilei Xing <beilei.xing@intel.com>
Beilei Xing [Thu, 23 Jun 2016 07:22:10 +0000 (15:22 +0800)]
net/ixgbe/base: add SGMII link for X550
This patch adds new phy type and media type to support
SGMII link for X550, and add ixgbe_setup_sgmii to support
SGMII link setup.
Signed-off-by: Beilei Xing <beilei.xing@intel.com>
Beilei Xing [Thu, 23 Jun 2016 07:22:09 +0000 (15:22 +0800)]
net/ixgbe/base: add new VF requests to mailbox API
This patch adds two new VF requests of IXGBE_VF_GET_RETA and
IXGBE_VF_GET_RSS_KEY to the mailbox API.
Signed-off-by: Beilei Xing <beilei.xing@intel.com>
Nélio Laranjeiro [Fri, 24 Jun 2016 13:18:04 +0000 (15:18 +0200)]
net/mlx5: re-add Rx scatter support
This commit brings back Rx scatter and related support by the MTU update
function. The maximum number of segments per packet is not a fixed value
anymore (previously MLX5_PMD_SGE_WR_N, set to 4 by default) as it caused
performance issues when fewer segments were actually needed as well as
limitations on the maximum packet size that could be received with the
default mbuf size (supporting at most 8576 bytes).
These limitations are now lifted as the number of SGEs is derived from the
MTU (which implies MRU) at queue initialization and during MTU update.
Signed-off-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
Signed-off-by: Vasily Philipov <vasilyf@mellanox.com>
Signed-off-by: Nelio Laranjeiro <nelio.laranjeiro@6wind.com>
Adrien Mazarguil [Fri, 24 Jun 2016 13:18:03 +0000 (15:18 +0200)]
net/mlx5: make Rx queue reinitialization safer
The primary purpose of rxq_rehash() function is to stop and restart
reception on a queue after re-posting buffers. This may fail if the array
that temporarily stores existing buffers for reuse cannot be allocated.
Update rxq_rehash() to work on the target queue directly (not through a
template copy) and avoid this allocation.
rxq_alloc_elts() is modified accordingly to take buffers from an existing
queue directly and update their refcount.
Unlike rxq_rehash(), rxq_setup() must work on a temporary structure but
should not allocate new mbufs from the pool while reinitializing an
existing queue. This is achieved by using the refcount-aware
rxq_alloc_elts() before overwriting queue data.
Signed-off-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
Signed-off-by: Vasily Philipov <vasilyf@mellanox.com>
Adrien Mazarguil [Fri, 24 Jun 2016 13:18:02 +0000 (15:18 +0200)]
net/mlx5: remove redundant Rx queue initialization
Toggling RX checksum offloads is already done at initialization time. This
code does not belong in rxq_rehash().
Signed-off-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
Signed-off-by: Nelio Laranjeiro <nelio.laranjeiro@6wind.com>
Adrien Mazarguil [Fri, 24 Jun 2016 13:18:00 +0000 (15:18 +0200)]
net/mlx5: re-add Tx gather support
Compared to its previous incarnation, the software limit on the number of
mbuf segments is no more (previously MLX5_PMD_SGE_WR_N, set to 4 by
default) hence no need for linearization code and related buffers that
permanently consumed a non negligible amount of memory to handle oversized
mbufs.
The resulting code is both lighter and faster.
With the addition of this code, older GCC versions (such
as 4.8.5) may complain about 'wqe' variable being uninitialized, so
initialize it preemptively, even though it is not necessary to do so.
Signed-off-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
Signed-off-by: Nelio Laranjeiro <nelio.laranjeiro@6wind.com>
Adrien Mazarguil [Fri, 24 Jun 2016 13:17:59 +0000 (15:17 +0200)]
net/mlx5: check remaining space while processing Tx burst
The space necessary to store segmented packets cannot be known in advance
and must be verified for each of them.
Signed-off-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
Signed-off-by: Nelio Laranjeiro <nelio.laranjeiro@6wind.com>
Adrien Mazarguil [Fri, 24 Jun 2016 13:17:58 +0000 (15:17 +0200)]
net/mlx5: add debug information about Tx queues capabilities
Signed-off-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
Nélio Laranjeiro [Fri, 24 Jun 2016 13:17:57 +0000 (15:17 +0200)]
net/mlx5: support multi-packet send
This feature enables the TX burst function to emit up to 5 packets using
only two work queue entries (WQEs) on devices that support it. Saves PCI
bandwidth and improves performance.
Signed-off-by: Nelio Laranjeiro <nelio.laranjeiro@6wind.com>
Signed-off-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
Signed-off-by: Olga Shern <olgas@mellanox.com>
Yaacov Hazan [Fri, 24 Jun 2016 13:17:56 +0000 (15:17 +0200)]
net/mlx5: support inline send
Implement send inline feature which copies packet data directly into
work queue entries (WQEs) for improved latency. The maximum packet
size and the minimum number of Tx queues to qualify for inline send
are user-configurable.
This feature is effective when HW causes a performance bottleneck.
Signed-off-by: Yaacov Hazan <yaacovh@mellanox.com>
Signed-off-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
Signed-off-by: Nelio Laranjeiro <nelio.laranjeiro@6wind.com>
Adrien Mazarguil [Fri, 24 Jun 2016 13:17:55 +0000 (15:17 +0200)]
net/mlx5: replace countdown with threshold for Tx completions
Replacing the variable countdown (which depends on the number of
descriptors) with a fixed relative threshold known at compile time improves
performance by reducing the TX queue structure footprint and the amount of
code to manage completions during a burst.
Completions are now requested at most once per burst after threshold is
reached.
Signed-off-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
Signed-off-by: Nelio Laranjeiro <nelio.laranjeiro@6wind.com>
Signed-off-by: Vasily Philipov <vasilyf@mellanox.com>
Nélio Laranjeiro [Fri, 24 Jun 2016 13:17:54 +0000 (15:17 +0200)]
net/mlx5: handle Rx CQE compression
Mini (compressed) completion queue entries (CQEs) are returned by the
NIC when PCI back pressure is detected, in which case the first CQE64
contains common packet information followed by a number of CQE8
providing the rest, followed by a matching number of empty CQE64
entries to be used by software for decompression.
Before decompression:
0 1 2 6 7 8
+-------+ +---------+ +-------+ +-------+ +-------+ +-------+
| CQE64 | | CQE64 | | CQE64 | | CQE64 | | CQE64 | | CQE64 |
|-------| |---------| |-------| |-------| |-------| |-------|
| ..... | | cqe8[0] | | | . | | | | | ..... |
| ..... | | cqe8[1] | | | . | | | | | ..... |
| ..... | | ....... | | | . | | | | | ..... |
| ..... | | cqe8[7] | | | | | | | | ..... |
+-------+ +---------+ +-------+ +-------+ +-------+ +-------+
After decompression:
0 1 ... 8
+-------+ +-------+ +-------+
| CQE64 | | CQE64 | | CQE64 |
|-------| |-------| |-------|
| ..... | | ..... | . | ..... |
| ..... | | ..... | . | ..... |
| ..... | | ..... | . | ..... |
| ..... | | ..... | | ..... |
+-------+ +-------+ +-------+
This patch does not perform the entire decompression step as it would be
really expensive, instead the first CQE64 is consumed and an internal
context is maintained to interpret the following CQE8 entries directly.
Intermediate empty CQE64 entries are handed back to HW without further
processing.
Signed-off-by: Nelio Laranjeiro <nelio.laranjeiro@6wind.com>
Signed-off-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
Signed-off-by: Olga Shern <olgas@mellanox.com>
Signed-off-by: Vasily Philipov <vasilyf@mellanox.com>
Nélio Laranjeiro [Fri, 24 Jun 2016 13:17:53 +0000 (15:17 +0200)]
net/mlx5: refactor Tx data path
Bypass Verbs to improve Tx performance.
Signed-off-by: Nelio Laranjeiro <nelio.laranjeiro@6wind.com>
Signed-off-by: Yaacov Hazan <yaacovh@mellanox.com>
Signed-off-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
Nélio Laranjeiro [Fri, 24 Jun 2016 13:17:52 +0000 (15:17 +0200)]
net/mlx5: refactor Rx data path
Bypass Verbs to improve RX performance.
Signed-off-by: Nelio Laranjeiro <nelio.laranjeiro@6wind.com>
Signed-off-by: Yaacov Hazan <yaacovh@mellanox.com>
Signed-off-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
Signed-off-by: Vasily Philipov <vasilyf@mellanox.com>
Nélio Laranjeiro [Fri, 24 Jun 2016 13:17:51 +0000 (15:17 +0200)]
net/mlx5: add Tx/Rx burst function selection wrapper
These wrappers are meant to prevent code duplication later.
Signed-off-by: Nelio Laranjeiro <nelio.laranjeiro@6wind.com>
Signed-off-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
Nélio Laranjeiro [Fri, 24 Jun 2016 13:17:50 +0000 (15:17 +0200)]
net/mlx5: add support for configuration through kvargs
The intent is to replace the remaining compile-time options and environment
variables with a common mean of runtime configuration. This commit only
adds the kvargs handling code, subsequent commits will update the rest.
Signed-off-by: Nelio Laranjeiro <nelio.laranjeiro@6wind.com>
Signed-off-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
Nélio Laranjeiro [Fri, 24 Jun 2016 13:17:49 +0000 (15:17 +0200)]
net/mlx5: add definitions for data path without Verbs
These structures and macros extend those exposed by libmlx5 (in mlx5_hw.h)
to let the PMD manage work queue and completion queue elements directly.
Signed-off-by: Nelio Laranjeiro <nelio.laranjeiro@6wind.com>
Signed-off-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
Nélio Laranjeiro [Fri, 24 Jun 2016 13:17:48 +0000 (15:17 +0200)]
net/mlx5: update prerequisites for upcoming enhancements
The latest version of Mellanox OFED exposes hardware definitions necessary
to implement data path operation bypassing Verbs. Update the minimum
version requirement to MLNX_OFED >= 3.3 and clean up compatibility checks
for previous releases.
Signed-off-by: Nelio Laranjeiro <nelio.laranjeiro@6wind.com>
Signed-off-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
Nélio Laranjeiro [Fri, 24 Jun 2016 13:17:47 +0000 (15:17 +0200)]
net/mlx5: split Rx queue structure
To keep the data path as efficient as possible, move fields only useful to
the control path into new structure rxq_ctrl.
Signed-off-by: Nelio Laranjeiro <nelio.laranjeiro@6wind.com>
Signed-off-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
Nélio Laranjeiro [Fri, 24 Jun 2016 13:17:46 +0000 (15:17 +0200)]
net/mlx5: split Tx queue structure
To keep the data path as efficient as possible, move fields only useful to
the control path into new structure txq_ctrl.
Signed-off-by: Nelio Laranjeiro <nelio.laranjeiro@6wind.com>
Signed-off-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
Nélio Laranjeiro [Fri, 24 Jun 2016 13:17:45 +0000 (15:17 +0200)]
net/mlx5: remove inline Tx support
Inline TX will be fully managed by the PMD after Verbs is bypassed in the
data path. Remove the current code until then.
Signed-off-by: Nelio Laranjeiro <nelio.laranjeiro@6wind.com>
Signed-off-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
Nélio Laranjeiro [Fri, 24 Jun 2016 13:17:44 +0000 (15:17 +0200)]
net/mlx5: remove configuration variable
There is no scatter/gather support anymore, CONFIG_RTE_LIBRTE_MLX5_SGE_WR_N
has no purpose and can be removed.
Signed-off-by: Nelio Laranjeiro <nelio.laranjeiro@6wind.com>
Signed-off-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
Nélio Laranjeiro [Fri, 24 Jun 2016 13:17:43 +0000 (15:17 +0200)]
net/mlx5: remove Rx scatter support
This is done in preparation of bypassing Verbs entirely for the data path
as a performance improvement. RX scatter cannot be maintained during the
transition and will be reimplemented later.
Signed-off-by: Nelio Laranjeiro <nelio.laranjeiro@6wind.com>
Signed-off-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
Nélio Laranjeiro [Fri, 24 Jun 2016 13:17:42 +0000 (15:17 +0200)]
net/mlx5: remove Tx gather support
This is done in preparation of bypassing Verbs entirely for the data path
as a performance improvement. TX gather cannot be maintained during the
transition and will be reimplemented later.
Signed-off-by: Nelio Laranjeiro <nelio.laranjeiro@6wind.com>
Signed-off-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
Nélio Laranjeiro [Fri, 24 Jun 2016 13:17:41 +0000 (15:17 +0200)]
net/mlx5: split memory registration function
Except for the first time when memory registration occurs, the lkey is
always cached. Since memory registration is slow and performs system calls,
performance can be improved by moving that code to its own function outside
of the data path so only the lookup code is left in the original inlined
function.
Signed-off-by: Nelio Laranjeiro <nelio.laranjeiro@6wind.com>
Signed-off-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
Nélio Laranjeiro [Fri, 24 Jun 2016 13:17:40 +0000 (15:17 +0200)]
net: fix PCI class id
Use RTE_PCI_DEVICE macro to set all fields rather than explicitly setting
them individually in the code. This shortens the code while helping to
future-proof against future changes to the rte_pci_id structure.
Fixes:
701c8d80c820 ("pci: support class id probing")
Signed-off-by: Nelio Laranjeiro <nelio.laranjeiro@6wind.com>
Ferruh Yigit [Thu, 23 Jun 2016 10:52:54 +0000 (11:52 +0100)]
net/vmxnet3: fix dump format
Remove 0x prefix for %p format to prevent double 0x in logs
Signed-off-by: Ferruh Yigit <ferruh.yigit@intel.com>
Acked-by: Yong Wang <yongwang@vmware.com>
Alejandro Lucero [Tue, 26 Apr 2016 11:36:41 +0000 (12:36 +0100)]
doc: update UIO module in nfp guide
Removing dependency on nfp_uio kernel module. The igb_uio
kernel modules can be used instead.
Fixes:
80bc1752f16e ("nfp: add guide")
Signed-off-by: Alejandro Lucero <alejandro.lucero@netronome.com>
Acked-by: John McNamara <john.mcnamara@intel.com>
Beilei Xing [Thu, 23 Jun 2016 15:11:58 +0000 (23:11 +0800)]
net/ixgbe: fix single VLAN tag to be outer VLAN tag
Previously, a single VLAN header is treated as inner VLAN,
but generally, a single VLAN header is treated as the outer
VLAN header.
The patch fixes the ether type of a single VLAN type, and
enables configuring inner and outer TPID for double VLAN.
Fixes:
19b16e2f6442 ("ethdev: add vlan type when setting ether type")
Signed-off-by: Beilei Xing <beilei.xing@intel.com>
Beilei Xing [Wed, 22 Jun 2016 02:53:51 +0000 (10:53 +0800)]
net/i40e: fix single VLAN tag to be outer VLAN tag
In current i40e codebase, if single VLAN header is added in a packet,
it's treated as inner VLAN. Generally, a single VLAN header is
treated as the outer VLAN header, so update the driver behaviour
appropriately.
Fixes:
19b16e2f6442 ("ethdev: add vlan type when setting ether type")
Signed-off-by: Beilei Xing <beilei.xing@intel.com>
Ajit Khaparde [Tue, 21 Jun 2016 21:58:20 +0000 (16:58 -0500)]
net/bnxt: support Cumulus+ Ethernet adapter
This patch adds support for Cumulus+ Ethernet adapters.
These Cumulus+ Ethernet adapters support 10Gb/25Gb/40Gb/50Gb speeds.
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
John Daley [Mon, 20 Jun 2016 19:27:46 +0000 (12:27 -0700)]
net/enic: fix negative array index write
Negative array index write using variable pos as an index to array
enic->fdir.nodes. Fixed by add array index check.
Coverity issue: 13270
Fixes:
fefed3d1e62c ("enic: new driver")
Signed-off-by: John Daley <johndale@cisco.com>
Jerin Jacob [Fri, 17 Jun 2016 14:06:44 +0000 (19:36 +0530)]
net/ixgbe: use mbuf prefetch function
made second cache line access behavior same as IA
Signed-off-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
Reviewed-by: Jianbo Liu <jianbo.liu@linaro.org>
Charles (Chas) Williams [Thu, 16 Jun 2016 22:50:06 +0000 (18:50 -0400)]
net/bnx2x: fix incorrect buffer length on Rx
The Rx function should not be setting the mbuf buffer length, so remove
the assignment.
Fixes:
540a211084a7 ("bnx2x: driver core")
Signed-off-by: Charles (Chas) Williams <ciwillia@brocade.com>
Acked-by: Harish Patil <harish.patil@qlogic.com>
Nelson Escobar [Thu, 16 Jun 2016 19:19:05 +0000 (12:19 -0700)]
net/enic: support scattered Rx
For performance reasons, this patch uses 2 VIC RQs per RQ presented to
DPDK.
The VIC requires that each descriptor be marked as either a start of
packet (SOP) descriptor or a non-SOP descriptor. A one RQ solution
requires skipping descriptors when receiving small packets and results
in bad performance when receiving many small packets.
The 2 RQ solution makes use of the VIC feature that allows a receive
on primary queue to 'spill over' into another queue if the receive is
too large to fit in the buffer assigned to the descriptor on the
primary queue. This means that there is no skipping of descriptors
when receiving small packets and results in much better performance.
Signed-off-by: Nelson Escobar <neescoba@cisco.com>
Reviewed-by: John Daley <johndale@cisco.com>
Beilei Xing [Thu, 16 Jun 2016 13:36:28 +0000 (21:36 +0800)]
net/e1000: configure outer VLAN TPID field
This patch enables configuring the outer TPID for double VLAN.
Note that all other TPID values, for single VLANs or inner VLAN in the
QinQ case, are read only.
Signed-off-by: Beilei Xing <beilei.xing@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Harish Patil [Thu, 16 Jun 2016 05:47:11 +0000 (22:47 -0700)]
net/qede: update version to 8.7.9.0_1.1.0.1
Signed-off-by: Harish Patil <harish.patil@qlogic.com>
Sony Chacko [Thu, 16 Jun 2016 05:47:10 +0000 (22:47 -0700)]
net/qede: enable VF-VF traffic with unmatched dest address
This patch enables VF to VF traffic with unmatched destination addresses.
The steps to enable this are:
- Enable promiscuous mode filter settings.
- Check for VF mode and enable promiscuous mode settings for VF.
- Check filter configuration to ensure conflicting filter modes
are not set.
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Harish Patil [Thu, 16 Jun 2016 05:47:09 +0000 (22:47 -0700)]
net/qede: support 100G
- Add device id to the PCI table
- Add polling for the slowpath events for CMT mode device
- Add prerequisites to allow 100g mode
* Min number of queues needed is 2
* Only even number of queues are allowed
- Update documentation
Signed-off-by: Harish Patil <harish.patil@qlogic.com>
Sony Chacko [Thu, 16 Jun 2016 05:47:07 +0000 (22:47 -0700)]
net/qede: set MTU
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
[NIC overview doc update]
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
Sony Chacko [Thu, 16 Jun 2016 05:47:06 +0000 (22:47 -0700)]
net/qede: query RSS redirection table
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Sony Chacko [Thu, 16 Jun 2016 05:47:05 +0000 (22:47 -0700)]
net/qede: update RSS redirection table
Add support for configuring the RSS redirection table and update
corresponding documentation.
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Sony Chacko [Thu, 16 Jun 2016 05:47:04 +0000 (22:47 -0700)]
net/qede: get RSS hash configuration
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Sony Chacko [Thu, 16 Jun 2016 05:47:03 +0000 (22:47 -0700)]
net/qede: support RSS hash configuration
Add support for setting hash configuration based on adapter capability
and update corresponding NIC documentation.
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Konstantin Ananyev [Wed, 15 Jun 2016 12:58:37 +0000 (13:58 +0100)]
net/ixgbe: fix missed packet types on Rx
ixgbe PMD RX function(s) misses some packet types that are:
- correctly recognised by the underlying HW.
- marked as supported by ixgbe_dev_supported_ptypes_get().
Fixes:
9586ebd358d5 ("ixgbe: replace some offload flags with packet type")
Signed-off-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Tested-by: Olivier Matz <olivier.matz@6wind.com>
Chen Jing D(Mark) [Wed, 8 Jun 2016 08:43:50 +0000 (16:43 +0800)]
doc: remove Match Interface in fm10k guide
Intel stopped supporting Match Interface, remove reference to it in the
documentation.
Signed-off-by: Chen Jing D(Mark) <jing.d.chen@intel.com>
Acked-by: John McNamara <john.mcnamara@intel.com>
Nelson Escobar [Tue, 14 Jun 2016 23:55:34 +0000 (16:55 -0700)]
net/enic: fix releasing mbufs when tearing down Rx queue
When trying to release the mbufs, the function was incorrectly
iterating over the max size configured instead of the actual size
of the ring.
Fixes:
947d860c821f ("enic: improve Rx performance")
Signed-off-by: Nelson Escobar <neescoba@cisco.com>
Reviewed-by: John Daley <johndale@cisco.com>
Nelson Escobar [Tue, 14 Jun 2016 23:54:05 +0000 (16:54 -0700)]
net/enic: improve packet type identification
- add l4 ptypes to the ones we report as supporting
- report/use RTE_PTYPE_L3_IPV4_EXT_UNKNOWN and
RTE_PTYPE_L3_IPV6_EXT_UNKNOWN instead of RTE_PTYPE_L3_IPV4 and
RTE_PTYPE_L3_IPV6 as vic can't distinguish between packets with
extentions and those without extentions.
- correctly set the ptype bits set on packets that are both tcp/udp
and a frag
- set RTE_PTYPE_L4_NONFRAG on ip packets we know are not udp, tcp,
or fragments.
Fixes:
947d860c821f ("enic: improve Rx performance")
Signed-off-by: Nelson Escobar <neescoba@cisco.com>
Reviewed-by: John Daley <johndale@cisco.com>
Zhe Tao [Tue, 14 Jun 2016 05:24:16 +0000 (13:24 +0800)]
net/i40e: fix offload flags for vector Rx
The flags for RSS and flow director are not set correctly in the vector
Rx function, so applications which use these flags will not work
correctly.
The problem is caused by incorrect constants for masking,
shuffling and shifting the descriptor bytes, to create the resultant
flags in the mbuf. Correcting the constants fixes the problem
Fixes:
9ed94e5bb04e ("i40e: add vector Rx")
Signed-off-by: Zhe Tao <zhe.tao@intel.com>
Reviewed-by: Piotr Azarewicz <piotrx.t.azarewicz@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Ricardo Salveti [Mon, 18 Apr 2016 03:06:06 +0000 (00:06 -0300)]
net/xenvirt: support dynamic page size
PAGE_SIZE constant is not defined on ARM since multiple values
are possible, so DPDK needs to dynamically get the page size.
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
Acked-by: Bruce Richardson <bruce.richardson@intel.com>
Charles (Chas) Williams [Fri, 10 Jun 2016 22:18:52 +0000 (18:18 -0400)]
net/bnx2x: fix MSIX vector and VF resource counts
If MSIX is available, the vector count given by the table size is one
less than the actual count. This count also limits the receive and
transmit queue resources the VF can support.
Fixes:
540a211084a7 ("bnx2x: driver core")
Signed-off-by: Charles (Chas) Williams <ciwillia@brocade.com>
Acked-by: Harish Patil <harish.patil@qlogic.com>
Eric Kinzie [Fri, 27 May 2016 19:44:06 +0000 (12:44 -0700)]
app/test: add external state machine in mode 4
This adds test cases for exercising the external state machine API to
the mode 4 autotest.
Signed-off-by: Eric Kinzie <ehkinzie@gmail.com>
Acked-by: Declan Doherty <declan.doherty@intel.com>
Eric Kinzie [Fri, 27 May 2016 19:44:05 +0000 (12:44 -0700)]
net/bonding: allow external state machine in mode 4
Provide functions to allow an external 802.3ad state machine to transmit
and receive LACPDUs and to set the collection/distribution flags on
slave interfaces.
Signed-off-by: Eric Kinzie <ehkinzie@gmail.com>
Acked-by: Declan Doherty <declan.doherty@intel.com>
Eric Kinzie [Sat, 7 May 2016 03:45:24 +0000 (20:45 -0700)]
net/bonding: inherit maximum Rx packet length
Instead of a hard-coded maximum receive length, allow the bonded interface
to inherit this limit from the slave interfaces. This allows
an application that uses jumbo frames to pass realistic values to
rte_eth_dev_configure without causing an error.
Before the bonding interface is configured, allow slaves with any
max_rx_pktlen to be added and remember the lowest of these values as
a candidate value. During dev_configure, set the bond device's
max_rx_pktlen to the candidate value. After this point only slaves
with a max_rx_pktlen greater or equal to that of the bonding device
can be added.
If all slaves are removed, the bond device's pktlen is cleared.
Signed-off-by: Eric Kinzie <ehkinzie@gmail.com>
Acked-by: Declan Doherty <declan.doherty@intel.com>
Jerin Jacob [Fri, 17 Jun 2016 13:29:53 +0000 (18:59 +0530)]
doc: add ThunderX nicvf
Updated doc/guides/nics/overview.rst, doc/guides/nics/thunderx.rst
and release notes
Changed "*" to "P" in overview.rst to capture the partially supported
feature as "*" creating alignment issues with Sphinx table
Signed-off-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
Signed-off-by: Slawomir Rosek <slawomir.rosek@semihalf.com>
Signed-off-by: Maciej Czekaj <maciej.czekaj@caviumnetworks.com>
Acked-by: John McNamara <john.mcnamara@intel.com>
Jerin Jacob [Fri, 17 Jun 2016 13:29:52 +0000 (18:59 +0530)]
net/thunderx: add device start/stop and close
Signed-off-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
Signed-off-by: Maciej Czekaj <maciej.czekaj@caviumnetworks.com>
Signed-off-by: Kamil Rytarowski <kamil.rytarowski@caviumnetworks.com>
Signed-off-by: Zyta Szpak <zyta.szpak@semihalf.com>
Signed-off-by: Slawomir Rosek <slawomir.rosek@semihalf.com>
Signed-off-by: Radoslaw Biernacki <rad@semihalf.com>
Jerin Jacob [Fri, 17 Jun 2016 13:29:51 +0000 (18:59 +0530)]
net/thunderx: support Tx queue start and stop
Signed-off-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
Signed-off-by: Maciej Czekaj <maciej.czekaj@caviumnetworks.com>
Signed-off-by: Kamil Rytarowski <kamil.rytarowski@caviumnetworks.com>
Signed-off-by: Zyta Szpak <zyta.szpak@semihalf.com>
Signed-off-by: Slawomir Rosek <slawomir.rosek@semihalf.com>
Signed-off-by: Radoslaw Biernacki <rad@semihalf.com>
Jerin Jacob [Fri, 17 Jun 2016 13:29:50 +0000 (18:59 +0530)]
net/thunderx: support Rx queue start and stop
Signed-off-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
Signed-off-by: Maciej Czekaj <maciej.czekaj@caviumnetworks.com>
Signed-off-by: Kamil Rytarowski <kamil.rytarowski@caviumnetworks.com>
Signed-off-by: Zyta Szpak <zyta.szpak@semihalf.com>
Signed-off-by: Slawomir Rosek <slawomir.rosek@semihalf.com>
Signed-off-by: Radoslaw Biernacki <rad@semihalf.com>
Jerin Jacob [Fri, 17 Jun 2016 13:29:49 +0000 (18:59 +0530)]
net/thunderx: get Rx queue count
Signed-off-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
Signed-off-by: Maciej Czekaj <maciej.czekaj@caviumnetworks.com>
Signed-off-by: Kamil Rytarowski <kamil.rytarowski@caviumnetworks.com>
Signed-off-by: Zyta Szpak <zyta.szpak@semihalf.com>
Signed-off-by: Slawomir Rosek <slawomir.rosek@semihalf.com>
Signed-off-by: Radoslaw Biernacki <rad@semihalf.com>
Jerin Jacob [Fri, 17 Jun 2016 13:29:48 +0000 (18:59 +0530)]
net/thunderx: query supported packet types
Signed-off-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
Signed-off-by: Maciej Czekaj <maciej.czekaj@caviumnetworks.com>
Signed-off-by: Kamil Rytarowski <kamil.rytarowski@caviumnetworks.com>
Signed-off-by: Zyta Szpak <zyta.szpak@semihalf.com>
Signed-off-by: Slawomir Rosek <slawomir.rosek@semihalf.com>
Signed-off-by: Radoslaw Biernacki <rad@semihalf.com>
Jerin Jacob [Fri, 17 Jun 2016 13:29:47 +0000 (18:59 +0530)]
net/thunderx: add single and multi-segment Rx
Signed-off-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
Signed-off-by: Maciej Czekaj <maciej.czekaj@caviumnetworks.com>
Signed-off-by: Kamil Rytarowski <kamil.rytarowski@caviumnetworks.com>
Signed-off-by: Zyta Szpak <zyta.szpak@semihalf.com>
Signed-off-by: Slawomir Rosek <slawomir.rosek@semihalf.com>
Signed-off-by: Radoslaw Biernacki <rad@semihalf.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
Jerin Jacob [Fri, 17 Jun 2016 13:29:46 +0000 (18:59 +0530)]
net/thunderx: add single and multi-segment Tx
Signed-off-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
Signed-off-by: Maciej Czekaj <maciej.czekaj@caviumnetworks.com>
Signed-off-by: Kamil Rytarowski <kamil.rytarowski@caviumnetworks.com>
Signed-off-by: Zyta Szpak <zyta.szpak@semihalf.com>
Signed-off-by: Slawomir Rosek <slawomir.rosek@semihalf.com>
Signed-off-by: Radoslaw Biernacki <rad@semihalf.com>
Jerin Jacob [Fri, 17 Jun 2016 13:29:45 +0000 (18:59 +0530)]
net/thunderx: add statistics
Signed-off-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
Signed-off-by: Maciej Czekaj <maciej.czekaj@caviumnetworks.com>
Signed-off-by: Kamil Rytarowski <kamil.rytarowski@caviumnetworks.com>
Signed-off-by: Zyta Szpak <zyta.szpak@semihalf.com>
Signed-off-by: Slawomir Rosek <slawomir.rosek@semihalf.com>
Signed-off-by: Radoslaw Biernacki <rad@semihalf.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
Jerin Jacob [Fri, 17 Jun 2016 13:29:44 +0000 (18:59 +0530)]
net/thunderx: support promiscuous mode
Signed-off-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
Signed-off-by: Maciej Czekaj <maciej.czekaj@caviumnetworks.com>
Signed-off-by: Kamil Rytarowski <kamil.rytarowski@caviumnetworks.com>
Signed-off-by: Zyta Szpak <zyta.szpak@semihalf.com>
Signed-off-by: Slawomir Rosek <slawomir.rosek@semihalf.com>
Signed-off-by: Radoslaw Biernacki <rad@semihalf.com>
Jerin Jacob [Fri, 17 Jun 2016 13:29:43 +0000 (18:59 +0530)]
net/thunderx: support MTU configuration
Signed-off-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
Signed-off-by: Maciej Czekaj <maciej.czekaj@caviumnetworks.com>
Signed-off-by: Kamil Rytarowski <kamil.rytarowski@caviumnetworks.com>
Signed-off-by: Zyta Szpak <zyta.szpak@semihalf.com>
Signed-off-by: Slawomir Rosek <slawomir.rosek@semihalf.com>
Signed-off-by: Radoslaw Biernacki <rad@semihalf.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
Jerin Jacob [Fri, 17 Jun 2016 13:29:42 +0000 (18:59 +0530)]
net/thunderx: support RSS and RETA query and update
Signed-off-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
Signed-off-by: Maciej Czekaj <maciej.czekaj@caviumnetworks.com>
Signed-off-by: Kamil Rytarowski <kamil.rytarowski@caviumnetworks.com>
Signed-off-by: Zyta Szpak <zyta.szpak@semihalf.com>
Signed-off-by: Slawomir Rosek <slawomir.rosek@semihalf.com>
Signed-off-by: Radoslaw Biernacki <rad@semihalf.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
Jerin Jacob [Fri, 17 Jun 2016 13:29:41 +0000 (18:59 +0530)]
net/thunderx: add Tx queue setup and release
Signed-off-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
Signed-off-by: Maciej Czekaj <maciej.czekaj@caviumnetworks.com>
Signed-off-by: Kamil Rytarowski <kamil.rytarowski@caviumnetworks.com>
Signed-off-by: Zyta Szpak <zyta.szpak@semihalf.com>
Signed-off-by: Slawomir Rosek <slawomir.rosek@semihalf.com>
Signed-off-by: Radoslaw Biernacki <rad@semihalf.com>
Jerin Jacob [Fri, 17 Jun 2016 13:29:40 +0000 (18:59 +0530)]
net/thunderx: add Rx queue setup and release
Signed-off-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
Signed-off-by: Maciej Czekaj <maciej.czekaj@caviumnetworks.com>
Signed-off-by: Kamil Rytarowski <kamil.rytarowski@caviumnetworks.com>
Signed-off-by: Zyta Szpak <zyta.szpak@semihalf.com>
Signed-off-by: Slawomir Rosek <slawomir.rosek@semihalf.com>
Signed-off-by: Radoslaw Biernacki <rad@semihalf.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
Jerin Jacob [Fri, 17 Jun 2016 13:29:39 +0000 (18:59 +0530)]
net/thunderx: get device infos
Signed-off-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
Signed-off-by: Maciej Czekaj <maciej.czekaj@caviumnetworks.com>
Signed-off-by: Kamil Rytarowski <kamil.rytarowski@caviumnetworks.com>
Signed-off-by: Zyta Szpak <zyta.szpak@semihalf.com>
Signed-off-by: Slawomir Rosek <slawomir.rosek@semihalf.com>
Signed-off-by: Radoslaw Biernacki <rad@semihalf.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
Jerin Jacob [Fri, 17 Jun 2016 13:29:38 +0000 (18:59 +0530)]
net/thunderx: support ethdev configure
Signed-off-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
Signed-off-by: Maciej Czekaj <maciej.czekaj@caviumnetworks.com>
Signed-off-by: Kamil Rytarowski <kamil.rytarowski@caviumnetworks.com>
Signed-off-by: Zyta Szpak <zyta.szpak@semihalf.com>
Signed-off-by: Slawomir Rosek <slawomir.rosek@semihalf.com>
Signed-off-by: Radoslaw Biernacki <rad@semihalf.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
Jerin Jacob [Fri, 17 Jun 2016 13:29:37 +0000 (18:59 +0530)]
net/thunderx: support register dump
Signed-off-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
Signed-off-by: Maciej Czekaj <maciej.czekaj@caviumnetworks.com>
Signed-off-by: Kamil Rytarowski <kamil.rytarowski@caviumnetworks.com>
Signed-off-by: Zyta Szpak <zyta.szpak@semihalf.com>
Signed-off-by: Slawomir Rosek <slawomir.rosek@semihalf.com>
Signed-off-by: Radoslaw Biernacki <rad@semihalf.com>
Jerin Jacob [Fri, 17 Jun 2016 13:29:36 +0000 (18:59 +0530)]
net/thunderx: add link status and update
Extended the nicvf_interrupt function to respond
NIC_MBOX_MSG_BGX_LINK_CHANGE mbox message from PF and update
struct rte_eth_link accordingly.
Signed-off-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
Signed-off-by: Maciej Czekaj <maciej.czekaj@caviumnetworks.com>
Signed-off-by: Kamil Rytarowski <kamil.rytarowski@caviumnetworks.com>
Signed-off-by: Zyta Szpak <zyta.szpak@semihalf.com>
Signed-off-by: Slawomir Rosek <slawomir.rosek@semihalf.com>
Signed-off-by: Radoslaw Biernacki <rad@semihalf.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
Jerin Jacob [Fri, 17 Jun 2016 13:29:35 +0000 (18:59 +0530)]
net/thunderx: add PMD skeleton
Introduce driver initialization and enable build infrastructure for
nicvf pmd driver.
By default, It is enabled only for defconfig_arm64-thunderx-*
config as it is an inbuilt NIC device.
Signed-off-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
Signed-off-by: Maciej Czekaj <maciej.czekaj@caviumnetworks.com>
Signed-off-by: Kamil Rytarowski <kamil.rytarowski@caviumnetworks.com>
Signed-off-by: Zyta Szpak <zyta.szpak@semihalf.com>
Signed-off-by: Slawomir Rosek <slawomir.rosek@semihalf.com>
Signed-off-by: Radoslaw Biernacki <rad@semihalf.com>
Jerin Jacob [Fri, 17 Jun 2016 13:29:34 +0000 (18:59 +0530)]
net/thunderx/base: add statistics
Signed-off-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
Signed-off-by: Maciej Czekaj <maciej.czekaj@caviumnetworks.com>
Signed-off-by: Kamil Rytarowski <kamil.rytarowski@caviumnetworks.com>
Signed-off-by: Zyta Szpak <zyta.szpak@semihalf.com>
Signed-off-by: Slawomir Rosek <slawomir.rosek@semihalf.com>
Signed-off-by: Radoslaw Biernacki <rad@semihalf.com>
Jerin Jacob [Fri, 17 Jun 2016 13:29:33 +0000 (18:59 +0530)]
net/thunderx/base: add RSS and RETA configuration
Signed-off-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
Signed-off-by: Maciej Czekaj <maciej.czekaj@caviumnetworks.com>
Signed-off-by: Kamil Rytarowski <kamil.rytarowski@caviumnetworks.com>
Signed-off-by: Zyta Szpak <zyta.szpak@semihalf.com>
Signed-off-by: Slawomir Rosek <slawomir.rosek@semihalf.com>
Signed-off-by: Radoslaw Biernacki <rad@semihalf.com>
Jerin Jacob [Fri, 17 Jun 2016 13:29:32 +0000 (18:59 +0530)]
net/thunderx/base: add hardware API
add nicvf hardware specific APIs for initialization and configuration.
Signed-off-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
Signed-off-by: Maciej Czekaj <maciej.czekaj@caviumnetworks.com>
Signed-off-by: Kamil Rytarowski <kamil.rytarowski@caviumnetworks.com>
Signed-off-by: Zyta Szpak <zyta.szpak@semihalf.com>
Signed-off-by: Slawomir Rosek <slawomir.rosek@semihalf.com>
Signed-off-by: Radoslaw Biernacki <rad@semihalf.com>
Jerin Jacob [Fri, 17 Jun 2016 13:29:31 +0000 (18:59 +0530)]
net/thunderx/base: add mailbox for PF/VF communication
DPDK nicvf driver doesn't have access to NIC's PF address space.
Introduce a mailbox mechanism to communicate with PF driver through
shared 128bit register interface.
Signed-off-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
Signed-off-by: Maciej Czekaj <maciej.czekaj@caviumnetworks.com>
Signed-off-by: Kamil Rytarowski <kamil.rytarowski@caviumnetworks.com>
Signed-off-by: Zyta Szpak <zyta.szpak@semihalf.com>
Signed-off-by: Slawomir Rosek <slawomir.rosek@semihalf.com>
Signed-off-by: Radoslaw Biernacki <rad@semihalf.com>
Jerin Jacob [Fri, 17 Jun 2016 13:29:30 +0000 (18:59 +0530)]
net/thunderx/base: implement platform abstraction
implement DPDK based platform abstraction for base code
Signed-off-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
Signed-off-by: Maciej Czekaj <maciej.czekaj@caviumnetworks.com>
Signed-off-by: Kamil Rytarowski <kamil.rytarowski@caviumnetworks.com>
Signed-off-by: Zyta Szpak <zyta.szpak@semihalf.com>
Signed-off-by: Slawomir Rosek <slawomir.rosek@semihalf.com>
Signed-off-by: Radoslaw Biernacki <rad@semihalf.com>
Jerin Jacob [Fri, 17 Jun 2016 13:29:29 +0000 (18:59 +0530)]
net/thunderx/base: add HW register definitions
add HW register definitions of ThunderX inbuilt NIC
Signed-off-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
Signed-off-by: Maciej Czekaj <maciej.czekaj@caviumnetworks.com>
Signed-off-by: Kamil Rytarowski <kamil.rytarowski@caviumnetworks.com>
Signed-off-by: Zyta Szpak <zyta.szpak@semihalf.com>
Signed-off-by: Slawomir Rosek <slawomir.rosek@semihalf.com>
Signed-off-by: Radoslaw Biernacki <rad@semihalf.com>
Jerin Jacob [Fri, 17 Jun 2016 13:29:28 +0000 (18:59 +0530)]
net/thunderx/base: add HW constants
add HW constants of ThunderX inbuilt NIC
Signed-off-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
Signed-off-by: Maciej Czekaj <maciej.czekaj@caviumnetworks.com>
Signed-off-by: Kamil Rytarowski <kamil.rytarowski@caviumnetworks.com>
Signed-off-by: Zyta Szpak <zyta.szpak@semihalf.com>
Signed-off-by: Slawomir Rosek <slawomir.rosek@semihalf.com>
Signed-off-by: Radoslaw Biernacki <rad@semihalf.com>
Xiao Wang [Mon, 6 Jun 2016 09:00:47 +0000 (17:00 +0800)]
net/fm10k: fix promiscuous receive for VF
When app tries to change promisc/allmulti setting, fm10k will check if a
valid glort is acquired, and exit without doing anything if not.
For VFs, this glort value is not necessary, and so the check can be
removed. This saves having unnecessary failures of the API call, as well as
saving the time taken for the mailbox communication between VF and PF in
the case when the glort check passes.
Fixes:
df02ba864695 ("fm10k: support promiscuous mode")
Signed-off-by: Wang Xiao W <xiao.w.wang@intel.com>
Acked-by: Jing Chen <jing.d.chen@intel.com>
Olivier Matz [Mon, 13 Jun 2016 11:24:29 +0000 (13:24 +0200)]
net/xenvirt: fix build after mempool changes
The field elt_va_start has been removed from the mempool structure,
and it was not replaced in xenvirt.
Fix this by getting the mempool objects address by using the address of
the first memory chunk list.
Note that it won't work with mempool composed of several chunks,
but it was already the case before.
Fixes:
84121f197187 ("mempool: store memory chunks in a list")
Reported-by: Christian Ehrhardt <christian.ehrhardt@canonical.com>
Signed-off-by: Olivier Matz <olivier.matz@6wind.com>
Acked-by: Christian Ehrhardt <christian.ehrhardt@canonical.com>
Ajit Khaparde [Wed, 15 Jun 2016 21:23:38 +0000 (14:23 -0700)]
net/bnxt: add flow control operations
Add flow_ctrl_get and flow_ctrl_set dev_ops.
Uses the bnxt_set_hwrm_link_config() HWRM API added in earlier patch.
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: Stephen Hurd <stephen.hurd@broadcom.com>
Reviewed-by: David Christensen <david.christensen@broadcom.com>