git.droids-corp.org - dpdk.git/log

net/ixgbe/base: fix firmware command checksum error

When software sends commands to firmware using the host
slave command interface, firmware fails to receive the
command due to a checksum failed error, as the checksum is
not being correctly set by the driver software.

This patch sets command checksum to the default value of
0xFF, as per the datasheet, therefore the checksum won't
be checked by firmware.

Fixes: 86b8fb293fdf ("ixgbe/base: add sw-firmware sync for resource sharing on X550em_a")
Fixes: 0790adeb5675 ("ixgbe/base: support X550em_a device")

Signed-off-by: Beilei Xing <beilei.xing@intel.com>

net/ixgbe/base: add MAC link setup for X550a SFP

This patch adds ixgbe_setup_mac_link_sfp_x550a for X550a SFP.

Signed-off-by: Beilei Xing <beilei.xing@intel.com>

net/ixgbe/base: return error on VF MAC address failure

An error code indicating that the PF rejects the MAC address change
should be returned, in case that the PF has already assigned a MAC
for the VF.

Fixes: af75078fece3 ("first public release")

Signed-off-by: Beilei Xing <beilei.xing@intel.com>

net/ixgbe/base: add SGMII link for X550

This patch adds new phy type and media type to support
SGMII link for X550, and add ixgbe_setup_sgmii to support
SGMII link setup.

Signed-off-by: Beilei Xing <beilei.xing@intel.com>

net/ixgbe/base: add new VF requests to mailbox API

This patch adds two new VF requests of IXGBE_VF_GET_RETA and
IXGBE_VF_GET_RSS_KEY to the mailbox API.

Signed-off-by: Beilei Xing <beilei.xing@intel.com>

net/mlx5: re-add Rx scatter support

This commit brings back Rx scatter and related support by the MTU update
function. The maximum number of segments per packet is not a fixed value
anymore (previously MLX5_PMD_SGE_WR_N, set to 4 by default) as it caused
performance issues when fewer segments were actually needed as well as
limitations on the maximum packet size that could be received with the
default mbuf size (supporting at most 8576 bytes).

These limitations are now lifted as the number of SGEs is derived from the
MTU (which implies MRU) at queue initialization and during MTU update.

Signed-off-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
Signed-off-by: Vasily Philipov <vasilyf@mellanox.com>
Signed-off-by: Nelio Laranjeiro <nelio.laranjeiro@6wind.com>

net/mlx5: make Rx queue reinitialization safer

The primary purpose of rxq_rehash() function is to stop and restart
reception on a queue after re-posting buffers. This may fail if the array
that temporarily stores existing buffers for reuse cannot be allocated.

Update rxq_rehash() to work on the target queue directly (not through a
template copy) and avoid this allocation.

rxq_alloc_elts() is modified accordingly to take buffers from an existing
queue directly and update their refcount.

Unlike rxq_rehash(), rxq_setup() must work on a temporary structure but
should not allocate new mbufs from the pool while reinitializing an
existing queue. This is achieved by using the refcount-aware
rxq_alloc_elts() before overwriting queue data.

Signed-off-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
Signed-off-by: Vasily Philipov <vasilyf@mellanox.com>

net/mlx5: remove redundant Rx queue initialization

Toggling RX checksum offloads is already done at initialization time. This
code does not belong in rxq_rehash().

Signed-off-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
Signed-off-by: Nelio Laranjeiro <nelio.laranjeiro@6wind.com>

net/mlx5: re-add Tx gather support

Compared to its previous incarnation, the software limit on the number of
mbuf segments is no more (previously MLX5_PMD_SGE_WR_N, set to 4 by
default) hence no need for linearization code and related buffers that
permanently consumed a non negligible amount of memory to handle oversized
mbufs.

The resulting code is both lighter and faster.

With the addition of this code, older GCC versions (such
as 4.8.5) may complain about 'wqe' variable being uninitialized, so
initialize it preemptively, even though it is not necessary to do so.

Signed-off-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
Signed-off-by: Nelio Laranjeiro <nelio.laranjeiro@6wind.com>

net/mlx5: check remaining space while processing Tx burst

The space necessary to store segmented packets cannot be known in advance
and must be verified for each of them.

Signed-off-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
Signed-off-by: Nelio Laranjeiro <nelio.laranjeiro@6wind.com>

net/mlx5: add debug information about Tx queues capabilities

Signed-off-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>

net/mlx5: support multi-packet send

This feature enables the TX burst function to emit up to 5 packets using
only two work queue entries (WQEs) on devices that support it. Saves PCI
bandwidth and improves performance.

Signed-off-by: Nelio Laranjeiro <nelio.laranjeiro@6wind.com>
Signed-off-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
Signed-off-by: Olga Shern <olgas@mellanox.com>

net/mlx5: support inline send

Implement send inline feature which copies packet data directly into
work queue entries (WQEs) for improved latency. The maximum packet
size and the minimum number of Tx queues to qualify for inline send
are user-configurable.

This feature is effective when HW causes a performance bottleneck.

Signed-off-by: Yaacov Hazan <yaacovh@mellanox.com>
Signed-off-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
Signed-off-by: Nelio Laranjeiro <nelio.laranjeiro@6wind.com>

net/mlx5: replace countdown with threshold for Tx completions

Replacing the variable countdown (which depends on the number of
descriptors) with a fixed relative threshold known at compile time improves
performance by reducing the TX queue structure footprint and the amount of
code to manage completions during a burst.

Completions are now requested at most once per burst after threshold is
reached.

Signed-off-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
Signed-off-by: Nelio Laranjeiro <nelio.laranjeiro@6wind.com>
Signed-off-by: Vasily Philipov <vasilyf@mellanox.com>

net/mlx5: handle Rx CQE compression

Mini (compressed) completion queue entries (CQEs) are returned by the
NIC when PCI back pressure is detected, in which case the first CQE64
contains common packet information followed by a number of CQE8
providing the rest, followed by a matching number of empty CQE64
entries to be used by software for decompression.

Before decompression:

      0           1          2           6         7         8
  +-------+  +---------+ +-------+   +-------+ +-------+ +-------+
  | CQE64 |  |  CQE64  | | CQE64 |   | CQE64 | | CQE64 | | CQE64 |
  |-------|  |---------| |-------|   |-------| |-------| |-------|
  | ..... |  | cqe8[0] | |       | . |       | |       | | ..... |
  | ..... |  | cqe8[1] | |       | . |       | |       | | ..... |
  | ..... |  | ....... | |       | . |       | |       | | ..... |
  | ..... |  | cqe8[7] | |       |   |       | |       | | ..... |
  +-------+  +---------+ +-------+   +-------+ +-------+ +-------+

After decompression:

      0          1     ...     8
  +-------+  +-------+     +-------+
  | CQE64 |  | CQE64 |     | CQE64 |
  |-------|  |-------|     |-------|
  | ..... |  | ..... |  .  | ..... |
  | ..... |  | ..... |  .  | ..... |
  | ..... |  | ..... |  .  | ..... |
  | ..... |  | ..... |     | ..... |
  +-------+  +-------+     +-------+

This patch does not perform the entire decompression step as it would be
really expensive, instead the first CQE64 is consumed and an internal
context is maintained to interpret the following CQE8 entries directly.

Intermediate empty CQE64 entries are handed back to HW without further
processing.

Signed-off-by: Nelio Laranjeiro <nelio.laranjeiro@6wind.com>
Signed-off-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
Signed-off-by: Olga Shern <olgas@mellanox.com>
Signed-off-by: Vasily Philipov <vasilyf@mellanox.com>

net/mlx5: refactor Tx data path

Bypass Verbs to improve Tx performance.

Signed-off-by: Nelio Laranjeiro <nelio.laranjeiro@6wind.com>
Signed-off-by: Yaacov Hazan <yaacovh@mellanox.com>
Signed-off-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>

net/mlx5: refactor Rx data path

Bypass Verbs to improve RX performance.

Signed-off-by: Nelio Laranjeiro <nelio.laranjeiro@6wind.com>
Signed-off-by: Yaacov Hazan <yaacovh@mellanox.com>
Signed-off-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
Signed-off-by: Vasily Philipov <vasilyf@mellanox.com>

net/mlx5: add Tx/Rx burst function selection wrapper

These wrappers are meant to prevent code duplication later.

Signed-off-by: Nelio Laranjeiro <nelio.laranjeiro@6wind.com>
Signed-off-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>

net/mlx5: add support for configuration through kvargs

The intent is to replace the remaining compile-time options and environment
variables with a common mean of runtime configuration. This commit only
adds the kvargs handling code, subsequent commits will update the rest.

Signed-off-by: Nelio Laranjeiro <nelio.laranjeiro@6wind.com>
Signed-off-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>

net/mlx5: add definitions for data path without Verbs

These structures and macros extend those exposed by libmlx5 (in mlx5_hw.h)
to let the PMD manage work queue and completion queue elements directly.

Signed-off-by: Nelio Laranjeiro <nelio.laranjeiro@6wind.com>
Signed-off-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>

net/mlx5: update prerequisites for upcoming enhancements

The latest version of Mellanox OFED exposes hardware definitions necessary
to implement data path operation bypassing Verbs. Update the minimum
version requirement to MLNX_OFED >= 3.3 and clean up compatibility checks
for previous releases.

Signed-off-by: Nelio Laranjeiro <nelio.laranjeiro@6wind.com>
Signed-off-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>

net/mlx5: split Rx queue structure

To keep the data path as efficient as possible, move fields only useful to
the control path into new structure rxq_ctrl.

Signed-off-by: Nelio Laranjeiro <nelio.laranjeiro@6wind.com>
Signed-off-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>

net/mlx5: split Tx queue structure

To keep the data path as efficient as possible, move fields only useful to
the control path into new structure txq_ctrl.

Signed-off-by: Nelio Laranjeiro <nelio.laranjeiro@6wind.com>
Signed-off-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>

net/mlx5: remove inline Tx support

Inline TX will be fully managed by the PMD after Verbs is bypassed in the
data path. Remove the current code until then.

Signed-off-by: Nelio Laranjeiro <nelio.laranjeiro@6wind.com>
Signed-off-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>

net/mlx5: remove configuration variable

There is no scatter/gather support anymore, CONFIG_RTE_LIBRTE_MLX5_SGE_WR_N
has no purpose and can be removed.

Signed-off-by: Nelio Laranjeiro <nelio.laranjeiro@6wind.com>
Signed-off-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>

net/mlx5: remove Rx scatter support

This is done in preparation of bypassing Verbs entirely for the data path
as a performance improvement. RX scatter cannot be maintained during the
transition and will be reimplemented later.

Signed-off-by: Nelio Laranjeiro <nelio.laranjeiro@6wind.com>
Signed-off-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>

net/mlx5: remove Tx gather support

This is done in preparation of bypassing Verbs entirely for the data path
as a performance improvement. TX gather cannot be maintained during the
transition and will be reimplemented later.

Signed-off-by: Nelio Laranjeiro <nelio.laranjeiro@6wind.com>
Signed-off-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>

net/mlx5: split memory registration function

Except for the first time when memory registration occurs, the lkey is
always cached. Since memory registration is slow and performs system calls,
performance can be improved by moving that code to its own function outside
of the data path so only the lookup code is left in the original inlined
function.

Signed-off-by: Nelio Laranjeiro <nelio.laranjeiro@6wind.com>
Signed-off-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>

net: fix PCI class id

Use RTE_PCI_DEVICE macro to set all fields rather than explicitly setting
them individually in the code. This shortens the code while helping to
future-proof against future changes to the rte_pci_id structure.

Fixes: 701c8d80c820 ("pci: support class id probing")

Signed-off-by: Nelio Laranjeiro <nelio.laranjeiro@6wind.com>

net/vmxnet3: fix dump format

Remove 0x prefix for %p format to prevent double 0x in logs

Signed-off-by: Ferruh Yigit <ferruh.yigit@intel.com>
Acked-by: Yong Wang <yongwang@vmware.com>

doc: update UIO module in nfp guide

Removing dependency on nfp_uio kernel module. The igb_uio
kernel modules can be used instead.

Fixes: 80bc1752f16e ("nfp: add guide")

Signed-off-by: Alejandro Lucero <alejandro.lucero@netronome.com>
Acked-by: John McNamara <john.mcnamara@intel.com>

net/ixgbe: fix single VLAN tag to be outer VLAN tag

Previously, a single VLAN header is treated as inner VLAN,
but generally, a single VLAN header is treated as the outer
VLAN header.
The patch fixes the ether type of a single VLAN type, and
enables configuring inner and outer TPID for double VLAN.

Fixes: 19b16e2f6442 ("ethdev: add vlan type when setting ether type")

Signed-off-by: Beilei Xing <beilei.xing@intel.com>

net/i40e: fix single VLAN tag to be outer VLAN tag

In current i40e codebase, if single VLAN header is added in a packet,
it's treated as inner VLAN. Generally, a single VLAN header is
treated as the outer VLAN header, so update the driver behaviour
appropriately.

Fixes: 19b16e2f6442 ("ethdev: add vlan type when setting ether type")

Signed-off-by: Beilei Xing <beilei.xing@intel.com>

net/bnxt: support Cumulus+ Ethernet adapter

This patch adds support for Cumulus+ Ethernet adapters.
These Cumulus+ Ethernet adapters support 10Gb/25Gb/40Gb/50Gb speeds.

Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>

net/enic: fix negative array index write

Negative array index write using variable pos as an index to array
enic->fdir.nodes. Fixed by add array index check.

Coverity issue: 13270

Fixes: fefed3d1e62c ("enic: new driver")

Signed-off-by: John Daley <johndale@cisco.com>

net/ixgbe: use mbuf prefetch function

made second cache line access behavior same as IA

Signed-off-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
Reviewed-by: Jianbo Liu <jianbo.liu@linaro.org>

net/bnx2x: fix incorrect buffer length on Rx

The Rx function should not be setting the mbuf buffer length, so remove
the assignment.

Fixes: 540a211084a7 ("bnx2x: driver core")

Signed-off-by: Charles (Chas) Williams <ciwillia@brocade.com>
Acked-by: Harish Patil <harish.patil@qlogic.com>

net/enic: support scattered Rx

For performance reasons, this patch uses 2 VIC RQs per RQ presented to
DPDK.

The VIC requires that each descriptor be marked as either a start of
packet (SOP) descriptor or a non-SOP descriptor. A one RQ solution
requires skipping descriptors when receiving small packets and results
in bad performance when receiving many small packets.

The 2 RQ solution makes use of the VIC feature that allows a receive
on primary queue to 'spill over' into another queue if the receive is
too large to fit in the buffer assigned to the descriptor on the
primary queue. This means that there is no skipping of descriptors
when receiving small packets and results in much better performance.

Signed-off-by: Nelson Escobar <neescoba@cisco.com>
Reviewed-by: John Daley <johndale@cisco.com>

net/e1000: configure outer VLAN TPID field

This patch enables configuring the outer TPID for double VLAN.
Note that all other TPID values, for single VLANs or inner VLAN in the
QinQ case, are read only.

Signed-off-by: Beilei Xing <beilei.xing@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>

net/qede: update version to 8.7.9.0_1.1.0.1

Signed-off-by: Harish Patil <harish.patil@qlogic.com>

net/qede: enable VF-VF traffic with unmatched dest address

This patch enables VF to VF traffic with unmatched destination addresses.
The steps to enable this are:
- Enable promiscuous mode filter settings.
- Check for VF mode and enable promiscuous mode settings for VF.
- Check filter configuration to ensure conflicting filter modes
are not set.

Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>

net/qede: support 100G

- Add device id to the PCI table
- Add polling for the slowpath events for CMT mode device
- Add prerequisites to allow 100g mode
* Min number of queues needed is 2
* Only even number of queues are allowed
- Update documentation

Signed-off-by: Harish Patil <harish.patil@qlogic.com>

net/qede: set MTU

Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
[NIC overview doc update]
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>

net/qede: query RSS redirection table

Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>

net/qede: update RSS redirection table

Add support for configuring the RSS redirection table and update
corresponding documentation.

Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>

net/qede: get RSS hash configuration

Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>

net/qede: support RSS hash configuration

Add support for setting hash configuration based on adapter capability
and update corresponding NIC documentation.

Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>

net/ixgbe: fix missed packet types on Rx

ixgbe PMD RX function(s) misses some packet types that are:
- correctly recognised by the underlying HW.
- marked as supported by ixgbe_dev_supported_ptypes_get().

Fixes: 9586ebd358d5 ("ixgbe: replace some offload flags with packet type")

Signed-off-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Tested-by: Olivier Matz <olivier.matz@6wind.com>

doc: remove Match Interface in fm10k guide

Intel stopped supporting Match Interface, remove reference to it in the
documentation.

Signed-off-by: Chen Jing D(Mark) <jing.d.chen@intel.com>
Acked-by: John McNamara <john.mcnamara@intel.com>

net/enic: fix releasing mbufs when tearing down Rx queue

When trying to release the mbufs, the function was incorrectly
iterating over the max size configured instead of the actual size
of the ring.

Fixes: 947d860c821f ("enic: improve Rx performance")

Signed-off-by: Nelson Escobar <neescoba@cisco.com>
Reviewed-by: John Daley <johndale@cisco.com>

net/enic: improve packet type identification

- add l4 ptypes to the ones we report as supporting
- report/use RTE_PTYPE_L3_IPV4_EXT_UNKNOWN and
  RTE_PTYPE_L3_IPV6_EXT_UNKNOWN instead of RTE_PTYPE_L3_IPV4 and
  RTE_PTYPE_L3_IPV6 as vic can't distinguish between packets with
  extentions and those without extentions.
- correctly set the ptype bits set on packets that are both tcp/udp
  and a frag
- set RTE_PTYPE_L4_NONFRAG on ip packets we know are not udp, tcp,
  or fragments.

Fixes: 947d860c821f ("enic: improve Rx performance")

Signed-off-by: Nelson Escobar <neescoba@cisco.com>
Reviewed-by: John Daley <johndale@cisco.com>

net/i40e: fix offload flags for vector Rx

The flags for RSS and flow director are not set correctly in the vector
Rx function, so applications which use these flags will not work
correctly.

The problem is caused by incorrect constants for masking,
shuffling and shifting the descriptor bytes, to create the resultant
flags in the mbuf. Correcting the constants fixes the problem

Fixes: 9ed94e5bb04e ("i40e: add vector Rx")

Signed-off-by: Zhe Tao <zhe.tao@intel.com>
Reviewed-by: Piotr Azarewicz <piotrx.t.azarewicz@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>

net/xenvirt: support dynamic page size

PAGE_SIZE constant is not defined on ARM since multiple values
are possible, so DPDK needs to dynamically get the page size.

Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
Acked-by: Bruce Richardson <bruce.richardson@intel.com>

net/bnx2x: fix MSIX vector and VF resource counts

If MSIX is available, the vector count given by the table size is one
less than the actual count. This count also limits the receive and
transmit queue resources the VF can support.

Fixes: 540a211084a7 ("bnx2x: driver core")

Signed-off-by: Charles (Chas) Williams <ciwillia@brocade.com>
Acked-by: Harish Patil <harish.patil@qlogic.com>

app/test: add external state machine in mode 4

This adds test cases for exercising the external state machine API to
the mode 4 autotest.

Signed-off-by: Eric Kinzie <ehkinzie@gmail.com>
Acked-by: Declan Doherty <declan.doherty@intel.com>

net/bonding: allow external state machine in mode 4

Provide functions to allow an external 802.3ad state machine to transmit
and receive LACPDUs and to set the collection/distribution flags on
slave interfaces.

Signed-off-by: Eric Kinzie <ehkinzie@gmail.com>
Acked-by: Declan Doherty <declan.doherty@intel.com>

net/bonding: inherit maximum Rx packet length

Instead of a hard-coded maximum receive length, allow the bonded interface
to inherit this limit from the slave interfaces.  This allows
an application that uses jumbo frames to pass realistic values to
rte_eth_dev_configure without causing an error.

Before the bonding interface is configured, allow slaves with any
max_rx_pktlen to be added and remember the lowest of these values as
a candidate value.  During dev_configure, set the bond device's
max_rx_pktlen to the candidate value.  After this point only slaves
with a max_rx_pktlen greater or equal to that of the bonding device
can be added.

If all slaves are removed, the bond device's pktlen is cleared.

Signed-off-by: Eric Kinzie <ehkinzie@gmail.com>
Acked-by: Declan Doherty <declan.doherty@intel.com>

doc: add ThunderX nicvf

Updated doc/guides/nics/overview.rst, doc/guides/nics/thunderx.rst
and release notes

Changed "*" to "P" in overview.rst to capture the partially supported
feature as "*" creating alignment issues with Sphinx table

Signed-off-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
Signed-off-by: Slawomir Rosek <slawomir.rosek@semihalf.com>
Signed-off-by: Maciej Czekaj <maciej.czekaj@caviumnetworks.com>
Acked-by: John McNamara <john.mcnamara@intel.com>

net/thunderx: add device start/stop and close

Signed-off-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
Signed-off-by: Maciej Czekaj <maciej.czekaj@caviumnetworks.com>
Signed-off-by: Kamil Rytarowski <kamil.rytarowski@caviumnetworks.com>
Signed-off-by: Zyta Szpak <zyta.szpak@semihalf.com>
Signed-off-by: Slawomir Rosek <slawomir.rosek@semihalf.com>
Signed-off-by: Radoslaw Biernacki <rad@semihalf.com>

net/thunderx: support Tx queue start and stop

Signed-off-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
Signed-off-by: Maciej Czekaj <maciej.czekaj@caviumnetworks.com>
Signed-off-by: Kamil Rytarowski <kamil.rytarowski@caviumnetworks.com>
Signed-off-by: Zyta Szpak <zyta.szpak@semihalf.com>
Signed-off-by: Slawomir Rosek <slawomir.rosek@semihalf.com>
Signed-off-by: Radoslaw Biernacki <rad@semihalf.com>

net/thunderx: support Rx queue start and stop

Signed-off-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
Signed-off-by: Maciej Czekaj <maciej.czekaj@caviumnetworks.com>
Signed-off-by: Kamil Rytarowski <kamil.rytarowski@caviumnetworks.com>
Signed-off-by: Zyta Szpak <zyta.szpak@semihalf.com>
Signed-off-by: Slawomir Rosek <slawomir.rosek@semihalf.com>
Signed-off-by: Radoslaw Biernacki <rad@semihalf.com>

net/thunderx: get Rx queue count

Signed-off-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
Signed-off-by: Maciej Czekaj <maciej.czekaj@caviumnetworks.com>
Signed-off-by: Kamil Rytarowski <kamil.rytarowski@caviumnetworks.com>
Signed-off-by: Zyta Szpak <zyta.szpak@semihalf.com>
Signed-off-by: Slawomir Rosek <slawomir.rosek@semihalf.com>
Signed-off-by: Radoslaw Biernacki <rad@semihalf.com>

net/thunderx: query supported packet types

Signed-off-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
Signed-off-by: Maciej Czekaj <maciej.czekaj@caviumnetworks.com>
Signed-off-by: Kamil Rytarowski <kamil.rytarowski@caviumnetworks.com>
Signed-off-by: Zyta Szpak <zyta.szpak@semihalf.com>
Signed-off-by: Slawomir Rosek <slawomir.rosek@semihalf.com>
Signed-off-by: Radoslaw Biernacki <rad@semihalf.com>

net/thunderx: add single and multi-segment Rx

Signed-off-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
Signed-off-by: Maciej Czekaj <maciej.czekaj@caviumnetworks.com>
Signed-off-by: Kamil Rytarowski <kamil.rytarowski@caviumnetworks.com>
Signed-off-by: Zyta Szpak <zyta.szpak@semihalf.com>
Signed-off-by: Slawomir Rosek <slawomir.rosek@semihalf.com>
Signed-off-by: Radoslaw Biernacki <rad@semihalf.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>

net/thunderx: add single and multi-segment Tx

Signed-off-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
Signed-off-by: Maciej Czekaj <maciej.czekaj@caviumnetworks.com>
Signed-off-by: Kamil Rytarowski <kamil.rytarowski@caviumnetworks.com>
Signed-off-by: Zyta Szpak <zyta.szpak@semihalf.com>
Signed-off-by: Slawomir Rosek <slawomir.rosek@semihalf.com>
Signed-off-by: Radoslaw Biernacki <rad@semihalf.com>

net/thunderx: add statistics

Signed-off-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
Signed-off-by: Maciej Czekaj <maciej.czekaj@caviumnetworks.com>
Signed-off-by: Kamil Rytarowski <kamil.rytarowski@caviumnetworks.com>
Signed-off-by: Zyta Szpak <zyta.szpak@semihalf.com>
Signed-off-by: Slawomir Rosek <slawomir.rosek@semihalf.com>
Signed-off-by: Radoslaw Biernacki <rad@semihalf.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>

net/thunderx: support promiscuous mode

Signed-off-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
Signed-off-by: Maciej Czekaj <maciej.czekaj@caviumnetworks.com>
Signed-off-by: Kamil Rytarowski <kamil.rytarowski@caviumnetworks.com>
Signed-off-by: Zyta Szpak <zyta.szpak@semihalf.com>
Signed-off-by: Slawomir Rosek <slawomir.rosek@semihalf.com>
Signed-off-by: Radoslaw Biernacki <rad@semihalf.com>

net/thunderx: support MTU configuration

Signed-off-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
Signed-off-by: Maciej Czekaj <maciej.czekaj@caviumnetworks.com>
Signed-off-by: Kamil Rytarowski <kamil.rytarowski@caviumnetworks.com>
Signed-off-by: Zyta Szpak <zyta.szpak@semihalf.com>
Signed-off-by: Slawomir Rosek <slawomir.rosek@semihalf.com>
Signed-off-by: Radoslaw Biernacki <rad@semihalf.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>

net/thunderx: support RSS and RETA query and update

Signed-off-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
Signed-off-by: Maciej Czekaj <maciej.czekaj@caviumnetworks.com>
Signed-off-by: Kamil Rytarowski <kamil.rytarowski@caviumnetworks.com>
Signed-off-by: Zyta Szpak <zyta.szpak@semihalf.com>
Signed-off-by: Slawomir Rosek <slawomir.rosek@semihalf.com>
Signed-off-by: Radoslaw Biernacki <rad@semihalf.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>

net/thunderx: add Tx queue setup and release

Signed-off-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
Signed-off-by: Maciej Czekaj <maciej.czekaj@caviumnetworks.com>
Signed-off-by: Kamil Rytarowski <kamil.rytarowski@caviumnetworks.com>
Signed-off-by: Zyta Szpak <zyta.szpak@semihalf.com>
Signed-off-by: Slawomir Rosek <slawomir.rosek@semihalf.com>
Signed-off-by: Radoslaw Biernacki <rad@semihalf.com>

net/thunderx: add Rx queue setup and release

Signed-off-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
Signed-off-by: Maciej Czekaj <maciej.czekaj@caviumnetworks.com>
Signed-off-by: Kamil Rytarowski <kamil.rytarowski@caviumnetworks.com>
Signed-off-by: Zyta Szpak <zyta.szpak@semihalf.com>
Signed-off-by: Slawomir Rosek <slawomir.rosek@semihalf.com>
Signed-off-by: Radoslaw Biernacki <rad@semihalf.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>

net/thunderx: get device infos

Signed-off-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
Signed-off-by: Maciej Czekaj <maciej.czekaj@caviumnetworks.com>
Signed-off-by: Kamil Rytarowski <kamil.rytarowski@caviumnetworks.com>
Signed-off-by: Zyta Szpak <zyta.szpak@semihalf.com>
Signed-off-by: Slawomir Rosek <slawomir.rosek@semihalf.com>
Signed-off-by: Radoslaw Biernacki <rad@semihalf.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>

net/thunderx: support ethdev configure

Signed-off-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
Signed-off-by: Maciej Czekaj <maciej.czekaj@caviumnetworks.com>
Signed-off-by: Kamil Rytarowski <kamil.rytarowski@caviumnetworks.com>
Signed-off-by: Zyta Szpak <zyta.szpak@semihalf.com>
Signed-off-by: Slawomir Rosek <slawomir.rosek@semihalf.com>
Signed-off-by: Radoslaw Biernacki <rad@semihalf.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>

net/thunderx: support register dump

Signed-off-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
Signed-off-by: Maciej Czekaj <maciej.czekaj@caviumnetworks.com>
Signed-off-by: Kamil Rytarowski <kamil.rytarowski@caviumnetworks.com>
Signed-off-by: Zyta Szpak <zyta.szpak@semihalf.com>
Signed-off-by: Slawomir Rosek <slawomir.rosek@semihalf.com>
Signed-off-by: Radoslaw Biernacki <rad@semihalf.com>

net/thunderx: add link status and update

Extended the nicvf_interrupt function to respond
NIC_MBOX_MSG_BGX_LINK_CHANGE mbox message from PF and update
struct rte_eth_link accordingly.

Signed-off-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
Signed-off-by: Maciej Czekaj <maciej.czekaj@caviumnetworks.com>
Signed-off-by: Kamil Rytarowski <kamil.rytarowski@caviumnetworks.com>
Signed-off-by: Zyta Szpak <zyta.szpak@semihalf.com>
Signed-off-by: Slawomir Rosek <slawomir.rosek@semihalf.com>
Signed-off-by: Radoslaw Biernacki <rad@semihalf.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>

net/thunderx: add PMD skeleton

Introduce driver initialization and enable build infrastructure for
nicvf pmd driver.

By default, It is enabled only for defconfig_arm64-thunderx-*
config as it is an inbuilt NIC device.

Signed-off-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
Signed-off-by: Maciej Czekaj <maciej.czekaj@caviumnetworks.com>
Signed-off-by: Kamil Rytarowski <kamil.rytarowski@caviumnetworks.com>
Signed-off-by: Zyta Szpak <zyta.szpak@semihalf.com>
Signed-off-by: Slawomir Rosek <slawomir.rosek@semihalf.com>
Signed-off-by: Radoslaw Biernacki <rad@semihalf.com>

net/thunderx/base: add statistics

Signed-off-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
Signed-off-by: Maciej Czekaj <maciej.czekaj@caviumnetworks.com>
Signed-off-by: Kamil Rytarowski <kamil.rytarowski@caviumnetworks.com>
Signed-off-by: Zyta Szpak <zyta.szpak@semihalf.com>
Signed-off-by: Slawomir Rosek <slawomir.rosek@semihalf.com>
Signed-off-by: Radoslaw Biernacki <rad@semihalf.com>

net/thunderx/base: add RSS and RETA configuration

Signed-off-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
Signed-off-by: Maciej Czekaj <maciej.czekaj@caviumnetworks.com>
Signed-off-by: Kamil Rytarowski <kamil.rytarowski@caviumnetworks.com>
Signed-off-by: Zyta Szpak <zyta.szpak@semihalf.com>
Signed-off-by: Slawomir Rosek <slawomir.rosek@semihalf.com>
Signed-off-by: Radoslaw Biernacki <rad@semihalf.com>

net/thunderx/base: add hardware API

add nicvf hardware specific APIs for initialization and configuration.

Signed-off-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
Signed-off-by: Maciej Czekaj <maciej.czekaj@caviumnetworks.com>
Signed-off-by: Kamil Rytarowski <kamil.rytarowski@caviumnetworks.com>
Signed-off-by: Zyta Szpak <zyta.szpak@semihalf.com>
Signed-off-by: Slawomir Rosek <slawomir.rosek@semihalf.com>
Signed-off-by: Radoslaw Biernacki <rad@semihalf.com>

net/thunderx/base: add mailbox for PF/VF communication

DPDK nicvf driver doesn't have access to NIC's PF address space.
Introduce a mailbox mechanism to communicate with PF driver through
shared 128bit register interface.

Signed-off-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
Signed-off-by: Maciej Czekaj <maciej.czekaj@caviumnetworks.com>
Signed-off-by: Kamil Rytarowski <kamil.rytarowski@caviumnetworks.com>
Signed-off-by: Zyta Szpak <zyta.szpak@semihalf.com>
Signed-off-by: Slawomir Rosek <slawomir.rosek@semihalf.com>
Signed-off-by: Radoslaw Biernacki <rad@semihalf.com>

net/thunderx/base: implement platform abstraction

implement DPDK based platform abstraction for base code

Signed-off-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
Signed-off-by: Maciej Czekaj <maciej.czekaj@caviumnetworks.com>
Signed-off-by: Kamil Rytarowski <kamil.rytarowski@caviumnetworks.com>
Signed-off-by: Zyta Szpak <zyta.szpak@semihalf.com>
Signed-off-by: Slawomir Rosek <slawomir.rosek@semihalf.com>
Signed-off-by: Radoslaw Biernacki <rad@semihalf.com>

net/thunderx/base: add HW register definitions

add HW register definitions of ThunderX inbuilt NIC

Signed-off-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
Signed-off-by: Maciej Czekaj <maciej.czekaj@caviumnetworks.com>
Signed-off-by: Kamil Rytarowski <kamil.rytarowski@caviumnetworks.com>
Signed-off-by: Zyta Szpak <zyta.szpak@semihalf.com>
Signed-off-by: Slawomir Rosek <slawomir.rosek@semihalf.com>
Signed-off-by: Radoslaw Biernacki <rad@semihalf.com>

net/thunderx/base: add HW constants

add HW constants of ThunderX inbuilt NIC

Signed-off-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
Signed-off-by: Maciej Czekaj <maciej.czekaj@caviumnetworks.com>
Signed-off-by: Kamil Rytarowski <kamil.rytarowski@caviumnetworks.com>
Signed-off-by: Zyta Szpak <zyta.szpak@semihalf.com>
Signed-off-by: Slawomir Rosek <slawomir.rosek@semihalf.com>
Signed-off-by: Radoslaw Biernacki <rad@semihalf.com>

net/fm10k: fix promiscuous receive for VF

When app tries to change promisc/allmulti setting, fm10k will check if a
valid glort is acquired, and exit without doing anything if not.

For VFs, this glort value is not necessary, and so the check can be
removed. This saves having unnecessary failures of the API call, as well as
saving the time taken for the mailbox communication between VF and PF in
the case when the glort check passes.

Fixes: df02ba864695 ("fm10k: support promiscuous mode")

Signed-off-by: Wang Xiao W <xiao.w.wang@intel.com>
Acked-by: Jing Chen <jing.d.chen@intel.com>

net/xenvirt: fix build after mempool changes

The field elt_va_start has been removed from the mempool structure,
and it was not replaced in xenvirt.

Fix this by getting the mempool objects address by using the address of
the first memory chunk list.

Note that it won't work with mempool composed of several chunks,
but it was already the case before.

Fixes: 84121f197187 ("mempool: store memory chunks in a list")

Reported-by: Christian Ehrhardt <christian.ehrhardt@canonical.com>
Signed-off-by: Olivier Matz <olivier.matz@6wind.com>
Acked-by: Christian Ehrhardt <christian.ehrhardt@canonical.com>

net/bnxt: add flow control operations

Add flow_ctrl_get and flow_ctrl_set dev_ops.
Uses the bnxt_set_hwrm_link_config() HWRM API added in earlier patch.

Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: Stephen Hurd <stephen.hurd@broadcom.com>
Reviewed-by: David Christensen <david.christensen@broadcom.com>

net/bnxt: add RSS hash configuration

Add rss_hash_update and rss_hash_conf_get dev_ops
Uses the bnxt_hwrm_vnic_rss_cfg() HWRM API added in the previous patch.

Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: Stephen Hurd <stephen.hurd@broadcom.com>
Reviewed-by: David Christensen <david.christensen@broadcom.com>

net/bnxt: add RSS redirection table operations

Add code to Update/query reta dev_ops
Uses the bnxt_hwrm_vnic_rss_cfg() HWRM API added earlier.

Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: Stephen Hurd <stephen.hurd@broadcom.com>
Reviewed-by: David Christensen <david.christensen@broadcom.com>

net/bnxt: add link state operations

Adds dev_ops to set link Up or Down as appropriate.
Uses the bnxt_set_hwrm_link_config() API added previously.

Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: Stephen Hurd <stephen.hurd@broadcom.com>
Reviewed-by: David Christensen <david.christensen@broadcom.com>

net/bnxt: add MAC address

This patch adds dev_ops to Add/Remove MAC addresses.
These use the bnxt_hwrm_set_filter() defined previously

Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: Stephen Hurd <stephen.hurd@broadcom.com>
Reviewed-by: David Christensen <david.christensen@broadcom.com>

net/bnxt: free memory in close operation

This patch adds code to free all resources except the one corresponding
to HWRM, which are required to notify the HWRM that the driver is unloaded
(these are freed in uninit()).

Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: Stephen Hurd <stephen.hurd@broadcom.com>
Reviewed-by: David Christensen <david.christensen@broadcom.com>

net/bnxt: add multicast

This patch adds dev_ops to enable/disable multicast traffic.
Uses the bnxt_hwrm_cfa_l2_set_rx_mask() API added earlier.

Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: Stephen Hurd <stephen.hurd@broadcom.com>
Reviewed-by: David Christensen <david.christensen@broadcom.com>

net/bnxt: add promiscuous mode

This patch adds the promiscuous mode enable and disable dev_ops.
Uses the bnxt_hwrm_cfa_l2_set_rx_mask() API added in an earlier commit.

Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: Stephen Hurd <stephen.hurd@broadcom.com>
Reviewed-by: David Christensen <david.christensen@broadcom.com>

net/bnxt: add start/stop/link update operations

This patch adds code to add the start, stop and link update dev_ops.

Also adds wrapper functions like bnxt_init_chip(), bnxt_init_nic(),
bnxt_alloc_mem(), bnxt_free_mem()

The BNXT driver will now minimally pass traffic with testpmd.

Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: Stephen Hurd <stephen.hurd@broadcom.com>
Reviewed-by: David Christensen <david.christensen@broadcom.com>

net/bnxt: query PHY configuration

Add HWRM calls to query the port's PHY and link configuration.

New HWRM call:
bnxt_hwrm_port_phy_qcfg
This command queries the PHY configuration for the port

Also adding helper function like bnxt_get_hwrm_link_config()
and bnxt_parse_hw_link_speed() parse the link state.

Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: Stephen Hurd <stephen.hurd@broadcom.com>
Reviewed-by: David Christensen <david.christensen@broadcom.com>

net/bnxt: allocate rings and groups

Add a top level functions to initialize ring groups, and functions
to allocate and free all the rings via HWRM.

A ring group is identified by an index. It consists of Rx or Tx ring id,
completion ring id and a statistics context. Once a ring group is
initialized, use this group index while creating the rings in the ASIC
using the appropriate HWRM API added via earlier patches.

Functions added:
bnxt_free_cp_ring
Calls the HWRM function generic ring free with arguments specific
to a completion ring and sanitizes the host completion structure
bnxt_free_all_hwrm_rings
Frees all the HWRM allocated hardware rings
bnxt_free_all_hwrm_resources
Frees all the resources allocated via the HRM in the hardware
bnxt_alloc_hwrm_rings
Allocates all the HWRM rings needed in the current configuration

This should be the last functionality needed to add start/stop
device operations.

Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: Stephen Hurd <stephen.hurd@broadcom.com>
Reviewed-by: David Christensen <david.christensen@broadcom.com>

net/bnxt: set L2 filters

New HWRM call:
bnxt_clear_hwrm_vnic_filters
This patch adds code to set and clear L2 filters from the
corresponding VNIC. These filters will determine the Rx flows

Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: Stephen Hurd <stephen.hurd@broadcom.com>
Reviewed-by: David Christensen <david.christensen@broadcom.com>

net/bnxt: free statistics context

Add function and associated structures and definitions to free
statistics context from the ASIC.

New HWRM call:
bnxt_hwrm_stat_ctx_free
This command is used to free a stat context.

Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: Stephen Hurd <stephen.hurd@broadcom.com>
Reviewed-by: David Christensen <david.christensen@broadcom.com>