mem: fix potential underflow on mem size calculation

If total memory is already bigger than max memory, an underflow
will occur on subtraction. Fix it by simply stopping whenever
we already have amount of memory that is bigger than maximum.

Fixes: 66cc45e293ed ("mem: replace memseg with memseg lists")

Signed-off-by: Anatoly Burakov <anatoly.burakov@intel.com>

memzone: document reserving zero-length memzones

Currently, reserving a memzone with length set to 0 will not trigger
any memory allocations, and memzone will instead be looking through
already allocated memory only. Document this limitation.

Signed-off-by: Anatoly Burakov <anatoly.burakov@intel.com>

memzone: fix size on reserving biggest memzone

Size of malloc heap elements include overhead, which should not
be counted as part of memzone.

Fixes: fafcc11985a2 ("mem: rework memzone to be allocated by malloc")
Cc: stable@dpdk.org
Signed-off-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>

memzone: fix race condition on alloc failure

Deallocation used the wrong function, which could have resulted in
race conditions because the function does not use locks internally.

Fixes: 1403f87d4fb8 ("malloc: enable memory hotplug support")

Signed-off-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>

mem: unmap unneeded space

When we ask to reserve virtual areas, we usually include
alignment in the mapping size, and that memory ends up
being wasted. Wasting a gigabyte of VA space while trying to
reserve one gigabyte is pretty expensive on 32-bit, so after
we're done mapping, unmap unneeded space.

Signed-off-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Bruce Richardson <bruce.richardson@intel.com>

mem: check if allocation size is too big

Mapping size is a 64-bit integer, but mmap() will accept size_t for
size mappings. A user could request a mapping with an alignment, which
would have overflown size_t, so check if (size + alignment) will
overflow size_t.

Signed-off-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Bruce Richardson <bruce.richardson@intel.com>

mem: fix typo in local function name

Fixes: 582bed1e1d1d ("mem: support mapping hugepages at runtime")

Signed-off-by: Thomas Monjalon <thomas@monjalon.net>
Acked-by: Anatoly Burakov <anatoly.burakov@intel.com>

eal: fix typo in doc of pointer offset macro

Fixes: af75078fece3 ("first public release")
Cc: stable@dpdk.org
Signed-off-by: Thomas Monjalon <thomas@monjalon.net>

eal: fix mempool ops name parsing

The code aimed to pick and remember the value of
mempool ops name from EAL command line arguments does not
copy the string and remembers the pointer provided
by getopt_long() directly. The latter could be clobbered
later and result in reading wrong mbuf pool ops name
by rte_mempool library.

Typically, this flaw could be avoided by using strdup()
to remember the string value of the option.

Fixes: a103a97e7191 ("eal: allow user to override default mempool driver")
Cc: stable@dpdk.org
Signed-off-by: Ivan Malov <ivan.malov@oktetlabs.ru>
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Acked-by: Santosh Shukla <santosh.shukla@caviumnetworks.com>

rawdev: remove dead code

Coverity issue: 260406
Fixes: c88b3f2558ed ("rawdev: introduce raw device library")
Cc: stable@dpdk.org
Signed-off-by: Shreyansh Jain <shreyansh.jain@nxp.com>

raw/skeleton: remove dead code

Coverity Issue: 260411
Fixes: 55ca1b0f2151 ("raw/skeleton: add test cases")
Cc: stable@dpdk.org
Signed-off-by: Shreyansh Jain <shreyansh.jain@nxp.com>

raw/skeleton: fix resource leak in test

Coverity issue: 260402
Fixes: 55ca1b0f2151 ("raw/skeleton: add test cases")
Cc: stable@dpdk.org
Signed-off-by: Shreyansh Jain <shreyansh.jain@nxp.com>

bus/fslmc: remove dead code

Coverity issue: 268338
Fixes: 828d51d8fc3e ("bus/fslmc: refactor scan and probe functions")
Cc: stable@dpdk.org
Signed-off-by: Shreyansh Jain <shreyansh.jain@nxp.com>
Acked-by: Hemant Agrawal <hemant.agrawal@nxp.com>

bus/fslmc: fix memory leak and cleanup

Coverity issue: 268327
Fixes: 828d51d8fc3e ("bus/fslmc: refactor scan and probe functions")
Cc: stable@dpdk.org
Signed-off-by: Shreyansh Jain <shreyansh.jain@nxp.com>
Acked-by: Hemant Agrawal <hemant.agrawal@nxp.com>

bus/dpaa: improve dynamic logging

Signed-off-by: Hemant Agrawal <hemant.agrawal@nxp.com>
Acked-by: Shreyansh Jain <shreyansh.jain@nxp.com>

net/dpaa: fix xstats implementation

Some of the applications are expecting that if n is 0, it shall
return the supported number of stats. e.g. VPP

Fixes: b21ed3e2a16d ("net/dpaa: support extended statistics")
Cc: stable@dpdk.org
Signed-off-by: Hemant Agrawal <hemant.agrawal@nxp.com>
Acked-by: Shreyansh Jain <shreyansh.jain@nxp.com>

bus/fslmc: improve debug logging

Signed-off-by: Hemant Agrawal <hemant.agrawal@nxp.com>
Acked-by: Shreyansh Jain <shreyansh.jain@nxp.com>

bus/fslmc: support device blacklisting

Signed-off-by: Hemant Agrawal <hemant.agrawal@nxp.com>
Acked-by: Shreyansh Jain <shreyansh.jain@nxp.com>

bus/dpaa: support device blacklisting

Signed-off-by: Hemant Agrawal <hemant.agrawal@nxp.com>
Acked-by: Shreyansh Jain <shreyansh.jain@nxp.com>

kni: fix possible mbuf leaks and speed up port release

rx_q fifo can only be released by kernel thread. There may be
mbuf leaks in rx_q because kernel threads are randomly stopped.

When the kni is released and netdev is unregisterd, convert the
physical address mbufs in rx_q to the virtual address in free_q.
By the way, alloc_q can be processed together to speed up the
release rate in userspace.

In my test, it is improved from 300-500ms with a mempool that has
 131072 mbufs to 10ms(regardless of the specifications).

Suggested-by: Ferruh Yigit <ferruh.yigit@intel.com>
Signed-off-by: Yangchao Zhou <zhouyates@gmail.com>
Acked-by: Ferruh Yigit <ferruh.yigit@intel.com>

examples/vhost_scsi: replace strncpy with strlcpy

Use strlcpy instead of strncpy.

Fixes: db75c7af19 ("examples/vhost_scsi: introduce a new sample app")
Cc: stable@dpdk.org
Signed-off-by: Reshma Pattan <reshma.pattan@intel.com>
Acked-by: Bruce Richardson <bruce.richardson@intel.com>

examples/ipsec-secgw: replace strncpy with strlcpy

Use strlcpy instead of strncpy.
Use strcpy where boundchecks on destination is not needed.

Fixes: 0d547ed037 ("examples/ipsec-secgw: support configuration file")
Fixes: 07b156199f ("examples/ipsec-secgw: fix configuration string termination")
Fixes: a1469c319f ("examples/ipsec-secgw: fix configuration parsing")
Cc: stable@dpdk.org
Signed-off-by: Reshma Pattan <reshma.pattan@intel.com>
Acked-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>

examples/quota_watermark: fix return type of threads

Gcc 8.0.1 reports incompatible cast between types i.e. from
`void (*)(void *)` to `(int (*)(void *)`.

Change the pipeline_stage prototype to retun int type
to fix the issue.

Fixes: a0ffcb257a ("examples/quota_watermark: correct code indentation")
Cc: stable@dpdk.org
Signed-off-by: Reshma Pattan <reshma.pattan@intel.com>
Acked-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
Signed-off-by: Thomas Monjalon <thomas@monjalon.net>

test/pipeline: fix return type of stub miss

New warning with gcc 8.1:
The table_action_stub_miss() function was incorrectly
declared as returning a typedef of
rte_pipeline_table_action_handler_miss, instead of what it
should have been, an int.
Changed this to declare the function as returning an int, and
now when the action_handler_miss is set to table_action_stub_miss
(cast as rte_pipeline_table_action_handler_miss), gcc 8.1 no
longer complains about the cast.

Fixes: 5205954791cb ("app/test: packet framework unit tests")
Cc: stable@dpdk.org
Signed-off-by: David Hunt <david.hunt@intel.com>
Reviewed-by: Reshma Pattan <reshma.pattan@intel.com>
Acked-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>

test/distributor: fix return type of thread function

New warning with gcc 8.1:
When casting the function pointer passed to
rte_eal_remote_launch() as an lcore_function_t *,
it expects the cast function to return an int, but
instead it was returning void. Fixed to return
an int.

Fixes: c3eabff124e6 ("distributor: add unit tests")
Cc: stable@dpdk.org
Signed-off-by: David Hunt <david.hunt@intel.com>
Acked-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>

test/reorder: fix freeing mbuf twice

mbufs are being freed twice in error, once in rte_mempool_put_bulk()
and then in rte_reorder_free(). Refactor the code so that we use
rte_reorder_free() to free mbufs in the reorder buffer, and use
rte_pktmbuf_free() to free any unused or drained mbufs.

Fixes: d0c9b58d71 ("app/test: new reorder unit test")
Cc: stable@dpdk.org
Signed-off-by: Reshma Pattan <reshma.pattan@intel.com>
Reviewed-by: David Hunt <david.hunt@intel.com>

hash: explicit casts for truncation in CRC32c

In function 'crc32c_sse42_u64_mimic':
rte_hash_crc.h:402:40:
warning: conversion from 'uint64_t' {aka 'long unsigned int'}
to 'uint32_t' {aka 'unsigned int'} may change value [-Wconversion]
  init_val = crc32c_sse42_u32(d.u32[0], init_val);

Fixes: 00bf774bab0b ("hash: add assembly implementation of CRC32 intrinsics")
Cc: stable@dpdk.org
Signed-off-by: Andy Green <andy@warmcat.com>
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>

hash: move stack declaration at top of CRC32c function

In function 'crc32c_2words':
rte_hash_crc.h:347:2:
warning: ISO C90 forbids mixed declarations and code
[-Wdeclaration-after-statement]
  uint32_t crc, term1, term2;

Fixes: d983cf41698f ("hash: add software CRC32 implementation")
Cc: stable@dpdk.org
Signed-off-by: Andy Green <andy@warmcat.com>
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>

ethdev: explicit cast of buffered Tx number

In function 'rte_eth_tx_buffer_flush':
rte_ethdev.h:4248:55:
warning: conversion from 'int' to 'uint16_t'
{aka 'short unsigned int'} may change value [-Wconversion]
   buffer->error_callback(&buffer->pkts[sent], to_send - sent,

Fixes: d6c99e62c852 ("ethdev: add buffered Tx")
Cc: stable@dpdk.org
Signed-off-by: Andy Green <andy@warmcat.com>
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>

net: move stack variable at top of VLAN strip function

In function 'rte_vlan_strip':
rte_ether.h:357:2:
warning: ISO C90 forbids mixed declarations and code
[-Wdeclaration-after-statement]
  struct vlan_hdr *vh = (struct vlan_hdr *)(eh + 1);

Fixes: c974021a5949 ("ether: add soft vlan encap/decap")
Cc: stable@dpdk.org
Signed-off-by: Andy Green <andy@warmcat.com>
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>

spinlock/x86: move stack declaration before code

In function 'rte_try_tm':
rte_spinlock.h:82:2:
warning: ISO C90 forbids mixed declarations and code
[-Wdeclaration-after-statement]
  int retries = RTE_RTM_MAX_RETRIES;

Fixes: ba7468997ea6 ("spinlock: add HTM lock elision for x86")
Cc: stable@dpdk.org
Signed-off-by: Andy Green <andy@warmcat.com>
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>

eal: declare trace buffer at top of own block

rte_dev.h:54:2:
warning: ISO C90 forbids mixed declarations and
code [-Wdeclaration-after-statement]
  char buffer[vsnprintf(NULL, 0, fmt, ap) + 1];

Fixes: b974e4a40cb5 ("ethdev: make error checking macros public")
Cc: stable@dpdk.org
Signed-off-by: Andy Green <andy@warmcat.com>
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>

eal: explicit cast of core id when getting index

rte_lcore.h: In function 'rte_lcore_index':
rte_lcore.h:122:14:
warning: conversion to 'int' from 'unsigned int' may change
the sign of the result [-Wsign-conversion]
   lcore_id = rte_lcore_id();

Fixes: 5583037a7950 ("eal: get relative core index")
Cc: stable@dpdk.org
Signed-off-by: Andy Green <andy@warmcat.com>
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>

eal: explicit cast of builtin for bsf32

rte_common.h:416:9:
warning: conversion to 'uint32_t' {aka 'unsigned int'} from
'int' may change the sign of the result [-Wsign-conversion]
  return __builtin_ctz(v);
         ^~~~~~~~~~~~~~~~

The builtin is defined to return int, but we want to
return it as uint32_t.  Its only defined valid return
values are positive integers or zero, which is OK for
uint32_t.  So just add an explicit cast.

Fixes: 03f6bced5bba ("eal: use intrinsic function")
Cc: stable@dpdk.org
Signed-off-by: Andy Green <andy@warmcat.com>
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>

bus/fpga: use strlcpy instead of strncpy

Gcc 8 reports a build error:

drivers/bus/ifpga/ifpga_bus.c:161:2: error: ‘strncpy’ specified
bound 256 equals destination size [-Werror=stringop-truncation]
  strncpy(afu_pr_conf.bs_path, path, sizeof(afu_pr_conf.bs_path));
  ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

Fixes: 05fa3d4a6539 ("bus/ifpga: add Intel FPGA bus library")

Signed-off-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>

crypto/ccp: add meson build

Signed-off-by: Ravi Kumar <Ravi1.kumar@amd.com>
Acked-by: Bruce Richardson <bruce.richardson@intel.com>

build: ensure compatibility with future meson versions

Meson 0.46 fixed a bug where "extract_all_objects" would not recursively
extract objects not compiled from source for a target. To keep backward
compatibility, a "recursive" keyword-arg was added to make this optional.
The value is "false" by default for now, but will change to "true" in
future, so we hard-code it to "false" in our code to ensure future
compatibility.

Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
Acked-by: Luca Boccassi <bluca@debian.org>

build: fix check for libbsd in meson

When we check for libbsd we were just checking for the library itself.
However, on some distros, e.g. CentOS, libbsd will be found even though
it's not usable by DPDK as it's missing the string header. Therefore we
should check for both the library and the header file.

Fixes: 5364de644a4b ("eal: support strlcpy function")

Signed-off-by: Bruce Richarson <bruce.richardson@intel.com>
Reported-by: Vladimir Medvedkin <medvedkinv@gmail.com>
Acked-by: Vladimir Medvedkin <medvedkinv@gmail.com>
Acked-by: Luca Boccassi <bluca@debian.org>

kernel: fix cross-build of Linux modules with meson

When cross-compiling, if no kernel_dir was specified, then the kernel
modules were still being compiled for the build machine. Fix this by
only building modules on cross-compile when we have a kernel_dir value
set. Print out a message indicating why we are skipping kernel
compilation, and in case that the headers for kernel compile are not
found, print a warning instead of erroring out.

Fixes: a52f4574f798 ("igb_uio: build with meson")

Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
Acked-by: Luca Boccassi <bluca@debian.org>

net/i40e: fix missing defines for non-AVX build

For non-AVX builds, the cflags used for compiling the i40e driver files
are not passed to the call to build the AVX-specific code path. This can
cause build failures.

../drivers/net/i40e/i40e_ethdev.h:888:42: error: ‘I40E_PFQF_HKEY_MAX_INDEX’ undeclared here (not in a function)

Fixes: e940646b20fa ("drivers/net: build Intel NIC PMDs with meson")

Reported-by: Shreyansh Jain <shreyansh.jain@nxp.com>
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
Tested-by: Shreyansh Jain <shreyansh.jain@nxp.com>

doc: add BPF library guide

Signed-off-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Acked-by: Ferruh Yigit <ferruh.yigit@intel.com>

test/bpf: introduce functional test

Signed-off-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Acked-by: Ferruh Yigit <ferruh.yigit@intel.com>

test/bpf: add samples

Add few simple eBPF programs as an example.

Signed-off-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Acked-by: Ferruh Yigit <ferruh.yigit@intel.com>

app/testpmd: add commands to load/unload BPF filters

Introduce new testpmd commands to load/unload RX/TX BPF-based filters.

Signed-off-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Acked-by: Ferruh Yigit <ferruh.yigit@intel.com>

bpf: introduce basic Rx/Tx filters

Introduce API to install BPF based filters on ethdev RX/TX path.
Current implementation is pure SW one, based on ethdev RX/TX
callback mechanism.

Signed-off-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Acked-by: Ferruh Yigit <ferruh.yigit@intel.com>

bpf: add JIT compilation for x86_64 ISA

Signed-off-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Acked-by: Ferruh Yigit <ferruh.yigit@intel.com>

bpf: add more checks

Add checks for:
 - all instructions are valid ones
   (known opcodes, correct syntax, valid reg/off/imm values, etc.)
 - no unreachable instructions
 - no loops
 - basic stack boundaries checks
 - division by zero

Still need to add checks for:
 - use/return only initialized registers and stack data.
 - memory boundaries violation

Signed-off-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Acked-by: Ferruh Yigit <ferruh.yigit@intel.com>

bpf: add ability to load eBPF program from ELF object file

Introduce rte_bpf_elf_load() function to provide ability to
load eBPF program from ELF object file.
It also adds dependency on libelf.

Signed-off-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Acked-by: Ferruh Yigit <ferruh.yigit@intel.com>

bpf: add BPF loading and execution framework

librte_bpf provides a framework to load and execute eBPF bytecode
inside user-space dpdk based applications.
It supports basic set of features from eBPF spec
(https://www.kernel.org/doc/Documentation/networking/filter.txt).

Not currently supported features:
 - JIT
 - cBPF
 - tail-pointer call
 - eBPF MAP
 - skb
 - function calls for 32-bit apps
 - mbuf pointer as input parameter for 32-bit apps

Signed-off-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Acked-by: Ferruh Yigit <ferruh.yigit@intel.com>

raw/ifpga: add Intel FPGA bus rawdev driver

Add Intel FPGA BUS Rawdev Driver which is based on
librte_rawdev library.

Signed-off-by: Rosen Xu <rosen.xu@intel.com>
Signed-off-by: Yanglong Wu <yanglong.wu@intel.com>
Signed-off-by: Tianfei Zhang <tianfei.zhang@intel.com>
Acked-by: Shreyansh Jain <shreyansh.jain@nxp.com>
Reviewed-by: Qi Zhang <qi.z.zhang@intel.com>

raw/ifpga/base: add Intel FPGA OPAE share code

This patch adds Intel FPGA Open Programmable Acceleration
Engine (OPAE)[1] base driver code, in order to support Intel
FPGA devices under DPDK. The base code currently supports
Intel FPGA solutions including integrated solution (Intel(R)
Xeon(R) CPU with FPGAs) and discrete solution (Intel(R)
Programmable Acceleration Card with Intel(R) Arria(R) 10 FPGA)
and it could be extended to support more FPGA devices in the
future. Please refer to [1][2] for more introduction on OPAE
and Intel FPGAs.

[1] https://01.org/OPAE
[2] https://www.altera.com/solutions/acceleration-hub/overview.html

Signed-off-by: Tianfei Zhang <tianfei.zhang@intel.com>
Signed-off-by: Hao Wu <hao.wu@intel.com>
Signed-off-by: Yilun Xu <yilun.xu@intel.com>
Reviewed-by: Qi Zhang <qi.z.zhang@intel.com>

bus/ifpga: add Intel FPGA bus library

Defined FPGA-BUS for Acceleration Drivers of AFUs

1. FPGA PCI Scan (1st Scan) follows DPDK UIO/VFIO PCI Scan Process,
probe Intel FPGA Rawdev Driver, it will be covered in following patches.

2. AFU Scan(2nd Scan) bind DPDK driver to FPGA Partial-Bitstream.
This scan is trigged by hotplug of IFPGA Rawdev probe, in this scan
the AFUs will be created and their drivers are also probed.

This patch will introduce rte_afu_device which describe the AFU device
listed in the FPGA-BUS.

Signed-off-by: Rosen Xu <rosen.xu@intel.com>
Signed-off-by: Tianfei Zhang <tianfei.zhang@intel.com>
Reviewed-by: Qi Zhang <qi.z.zhang@intel.com>

crypto/ccp: support run-time CPU based auth

CCP PMD supports authentication offload to either of CCP or CPU.
The earlier version of patch provides this option as compile time.
This patch changes this option from compile time to run time.
User can pass "ccp_auth_opt=1" as an additional arguments to vdev
parameter to enable authentication operations on CPU.

Signed-off-by: Ravi Kumar <ravi1.kumar@amd.com>

bbdev: change names of baseband devices

Change baseband device name:
 - from turbo_sw to baseband_turbo_sw
 - from bbdev_null to baseband_null
To keep backwards compatibility the old names are still valid

Signed-off-by: Kamil Chalupnik <kamilx.chalupnik@intel.com>
Acked-by: Amr Mokhtar <amr.mokhtar@intel.com>

doc: add compression driver and ISA-L PMD guides

This adds general compression drivers feature guide
as well as the ISA-L PMD documentation and guide.

Signed-off-by: Lee Daly <lee.daly@intel.com>
Reviewed-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>

compress/isal: add ISA-L decomp functionality

Adds decompression functionality, similar to compression,
this sets internal ISA-L structures, provides input & output mbuf
addresses, executes decompression, which ISA-L calls inflate and
finally error checks.

Signed-off-by: Lee Daly <lee.daly@intel.com>
Acked-by: Greg Tucker <greg.b.tucker@intel.com>
Reviewed-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>

compress/isal: add ISA-L compression functionality

Adds compression functionality, this sets internal ISA-L
structures, provides input & output mbuf addresses,
executes compression, which ISA-L calls deflate,
and finally error checks.

Signed-off-by: Lee Daly <lee.daly@intel.com>
Acked-by: Greg Tucker <greg.b.tucker@intel.com>
Reviewed-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>

compress/isal: add stats related ops

Add functions for statistic retrieval and resetting.

Signed-off-by: Lee Daly <lee.daly@intel.com>
Reviewed-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>

compress/isal: support burst enqueue/dequeue

This patchs adds support for the compressdev enqueue_burst
and dequeue_burst API operations.

Signed-off-by: Lee Daly <lee.daly@intel.com>
Reviewed-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>

compress/isal: add queue pair related ops

This adds queue pair operations such as setup and release.

Signed-off-by: Lee Daly <lee.daly@intel.com>
Reviewed-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>

compress/isal: add private xform related ops

This patch  creates, configures and frees the private xform, taking the
applications xform and using it to populate the PMDs own private xform
with the information which will be required for the compress/decompress
functions. This information includes the level, algorithm,
type of huffman code, type of checksum etc.

Signed-off-by: Lee Daly <lee.daly@intel.com>
Reviewed-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>

compress/isal: add basic PMD ops

Add basic device poll mode driver operations to
give ability to start, stop, close device etc.

Signed-off-by: Lee Daly <lee.daly@intel.com>
Reviewed-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>

compress/isal: add device init and de-init

This patch adds device initialization functionality such as
probe and create, also adding deinitialize functionality.
Dynamic logging component also added.

Signed-off-by: Lee Daly <lee.daly@intel.com>
Reviewed-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>

compress/isal: add skeleton ISA-L compression PMD

Adding basic skeleton of the ISA-L compression driver.
No compression functionality, but lays the foundation for
operations in the rest of the patchset.

The ISA-L compression driver utilizes Intel's ISA-L compression
library and compressdev API.

Signed-off-by: Lee Daly <lee.daly@intel.com>
Reviewed-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>

doc: update bbdev test app guide

Update the test app documentation:
- description of tests added
- usage of test app updated

Signed-off-by: Kamil Chalupnik <kamilx.chalupnik@intel.com>
Acked-by: Amr Mokhtar <amr.mokhtar@intel.com>

doc: add shared lib building instructions for bbdev

Added a note to enable building as a shared lib.

Signed-off-by: Kamil Chalupnik <kamilx.chalupnik@intel.com>
Acked-by: Amr Mokhtar <amr.mokhtar@intel.com>

doc: update bbdev guide

Update the documentation describing Wireless Baseband Device:
- device capabilities updated
- input/output data buffers description added
- details about implementation of turbo encode/decode
  operation added

Signed-off-by: Kamil Chalupnik <kamilx.chalupnik@intel.com>
Acked-by: Amr Mokhtar <amr.mokhtar@intel.com>

app/bbdev: improve readability

Improve readability of test application by replacing
int values with rte_bbdev_event_type enum.

Signed-off-by: Kamil Chalupnik <kamilx.chalupnik@intel.com>
Acked-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>

app/bbdev: add new test vectors

Creation of new vectors to test and validate BBDevice capabilities
Test app documentation updated accordingly

Signed-off-by: Kamil Chalupnik <kamilx.chalupnik@intel.com>
Acked-by: Amr Mokhtar <amr.mokhtar@intel.com>

app/bbdev: update default test vectors

Update test vectors directory for Wireless Baseband Device:
- update test vectors names
- python script used for tests execution updated

Update the test app documentation:
- vector test names updated

Signed-off-by: Kamil Chalupnik <kamilx.chalupnik@intel.com>
Acked-by: Amr Mokhtar <amr.mokhtar@intel.com>

bbdev: split queue groups

Splitting Queue Groups into UL/DL Groups in Turbo Software
Driver. They are independent for Decode/Encode.
Release note updated accordingly.

Signed-off-by: Kamil Chalupnik <kamilx.chalupnik@intel.com>
Acked-by: Amr Mokhtar <amr.mokhtar@intel.com>

bbdev: measure offload cost

New test created to measure offload cost.
Changes were introduced in API, turbo software driver
and test application

Signed-off-by: Kamil Chalupnik <kamilx.chalupnik@intel.com>
Acked-by: Amr Mokhtar <amr.mokhtar@intel.com>

baseband/turbo_sw: support optional CRC overlap

Support for optional CRC overlap in decode processing implemented
in Turbo Software driver

Signed-off-by: Kamil Chalupnik <kamilx.chalupnik@intel.com>
Acked-by: Amr Mokhtar <amr.mokhtar@intel.com>

baseband/turbo_sw: increase internal buffers

Sizes of the internal buffers used by decoding were increased due to
problem with memory for large vectors

Signed-off-by: Kamil Chalupnik <kamilx.chalupnik@intel.com>
Acked-by: Amr Mokhtar <amr.mokhtar@intel.com>

baseband/turbo_sw: scale likelihood ratio input

Update Turbo Software driver for Wireless Baseband Device:
- function scaling input LLR values to specific range [-16, 16] added
- new test vectors to check device capabilities added
- release note updated accordingly

Signed-off-by: Kamil Chalupnik <kamilx.chalupnik@intel.com>
Acked-by: Amr Mokhtar <amr.mokhtar@intel.com>

baseband/turbo_sw: move macros to bbdev library

Signed-off-by: Kamil Chalupnik <kamilx.chalupnik@intel.com>
Acked-by: Amr Mokhtar <amr.mokhtar@intel.com>

baseband/turbo_sw: optimize memory copy

Optimization of Turbo Software driver by limiting or changing
usage of memory copying function.

Signed-off-by: Kamil Chalupnik <kamilx.chalupnik@intel.com>
Acked-by: Amr Mokhtar <amr.mokhtar@intel.com>

baseband/turbo_sw: support FlexRAN 1.4.0

Adjusting BaseBand drivers code to changes in FlexRAN 1.4.0:
- update usage of crc functions after API changes

Update the documentation describing Wireless Baseband Device:
- FlexRAN releases mapping table added
- download and build instructions for BBDEV turbo_sw driver in
  compliance with FlexRAN 1.4.0 release added

Signed-off-by: Kamil Chalupnik <kamilx.chalupnik@intel.com>
Acked-by: Amr Mokhtar <amr.mokhtar@intel.com>

examples/ipsec-secgw: limit inflight packets count

Revert previous patch that introduce a performance
degradation in certain scenarios and add a configurable
limit for number inflight packets.

Revert
commit 84d4b5e4ec48 ("examples/ipsec-secgw: improve IPsec dequeue logic")
Cc: stable@dpdk.org
Signed-off-by: Radu Nicolau <radu.nicolau@intel.com>
Acked-by: Akhil Goyal <akhil.goyal@nxp.com>

app/crypto-perf: check minimum lcore number

The crypto performance application requires at least
two cores: one master core that launches the other slaves
and one core acting as slave running the crypto device.

Fixes: f8be1786b1b8 ("app/crypto-perf: introduce performance test application")
Cc: stable@dpdk.org
Signed-off-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
Acked-by: Fiona Trahe <fiona.trahe@intel.com>

test/crypto: enhance scheduler unit tests

Unit test cases for Multi-core mode, Fail-over mode,
anf Packet distribution mode are added to improve code coverage.

Signed-off-by: Jananee Parthasarathy <jananeex.m.parthasarathy@intel.com>
Acked-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>

crypto/dpaa2_sec: remove IOVA conversion for fle address

fle is already in virtual addressing mode - no need to perform
address conversion for it.

Fixes: 8d1f3a5d751b ("crypto/dpaa2_sec: support crypto operation")
Cc: stable@dpdk.org
Signed-off-by: Hemant Agrawal <hemant.agrawal@nxp.com>
Acked-by: Akhil Goyal <akhil.goyal@nxp.com>

app/crypto-perf: fix burst size calculation

This patch fixes segmentation fault in pmd_cyclecount_bench_ops
function in case when state->opts->nb_descriptors is not
natural multiple of burst size.
To reproduce run: dpdk-test-crypto-perf with params:
  --ptest pmd-cyclecount --pmd-cyclecount-delay-ms 5 \
  --devtype crypto_qat --optype cipher-then-auth \
  --cipher-algo aes-cbc --cipher-op encrypt \
  --cipher-key-sz 16 --cipher-iv-sz 16 \
  --auth-algo sha2-256-hmac \
  --auth-op generate --auth-key-sz 64 --digest-sz 32 \
  --total-ops 10000 --burst-sz 255 --buffer-sz 1024 --silent

Fixes: 96dfeb609be1 ("app/crypto-perf: add new PMD benchmarking mode")
Cc: stable@dpdk.org
Signed-off-by: Tomasz Jozwiak <tomaszx.jozwiak@intel.com>
Acked-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>

crypto/dpaa_sec: update maximum queue pairs to 8

The underlying hardware can support multiple queue pairs.

Signed-off-by: Nipun Gupta <nipun.gupta@nxp.com>
Acked-by: Akhil Goyal <akhil.goyal@nxp.com>

test/compress: add invalid configuration tests

Add tests that check if device configuration
is not successful when providing invalid parameters.

Signed-off-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
Acked-by: Fiona Trahe <fiona.trahe@intel.com>
Acked-by: Lee Daly <lee.daly@intel.com>

test/compress: add multi xform test

Add test that checks if multiple xforms can be
handled on a single enqueue call.

Signed-off-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
Acked-by: Fiona Trahe <fiona.trahe@intel.com>
Acked-by: Lee Daly <lee.daly@intel.com>

test/compress: add multi level test

Add test that checks if all compression levels
are supported and compress a buffer correctly.

Signed-off-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
Acked-by: Fiona Trahe <fiona.trahe@intel.com>
Acked-by: Lee Daly <lee.daly@intel.com>

test/compress: add multi op test

Add test that checks if multiple operations with
different buffers can be handled on a single enqueue call.

Signed-off-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
Acked-by: Fiona Trahe <fiona.trahe@intel.com>
Acked-by: Lee Daly <lee.daly@intel.com>

test/compress: add initial unit tests

This commit introduces the initial tests for compressdev,
performing basic compression and decompression operations
of sample test buffers, using the Zlib library in one direction
and compressdev in another direction, to make sure that
the library is compatible with Zlib.

Due to the use of Zlib API, the test is disabled by default,
to avoid adding a new dependency on DPDK.

Signed-off-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
Signed-off-by: Ashish Gupta <ashish.gupta@caviumnetworks.com>
Signed-off-by: Shally Verma <shally.verma@caviumnetworks.com>
Acked-by: Fiona Trahe <fiona.trahe@intel.com>
Acked-by: Lee Daly <lee.daly@intel.com>

doc: add compressdev library guide

Add section in programmer’s guide for Compressdev library.

Signed-off-by: Shally Verma <shally.verma@caviumnetworks.com>
Signed-off-by: Sunila Sahu <sunila.sahu@caviumnetworks.com>
Signed-off-by: Ashish Gupta <ashish.gupta@caviumnetworks.com>

compressdev: get device id from name

Added API to retrieve the device id provided the device name.

Signed-off-by: Fiona Trahe <fiona.trahe@intel.com>
Signed-off-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
Signed-off-by: Shally Verma <shally.verma@caviumnetworks.com>
Signed-off-by: Ashish Gupta <ashish.gupta@caviumnetworks.com>

compressdev: add device capabilities

Added structure which each PMD will fill out,
providing the capabilities of each driver
(containing mainly which compression services
it supports).

Signed-off-by: Fiona Trahe <fiona.trahe@intel.com>
Signed-off-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
Signed-off-by: Shally Verma <shally.verma@caviumnetworks.com>
Signed-off-by: Ashish Gupta <ashish.gupta@caviumnetworks.com>

compressdev: add device stats

Signed-off-by: Fiona Trahe <fiona.trahe@intel.com>
Signed-off-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
Signed-off-by: Shally Verma <shally.verma@caviumnetworks.com>
Signed-off-by: Ashish Gupta <ashish.gupta@caviumnetworks.com>

compressdev: add compression service feature flags

Signed-off-by: Fiona Trahe <fiona.trahe@intel.com>
Signed-off-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
Signed-off-by: Shally Verma <shally.verma@caviumnetworks.com>
Signed-off-by: Ashish Gupta <ashish.gupta@caviumnetworks.com>

compressdev: add device feature flags

Signed-off-by: Fiona Trahe <fiona.trahe@intel.com>
Signed-off-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
Signed-off-by: Shally Verma <shally.verma@caviumnetworks.com>
Signed-off-by: Ashish Gupta <ashish.gupta@caviumnetworks.com>

compressdev: support hash operations

- Added hash algo enumeration and params in xform and rte_comp_op
- Updated compress/decompress xform to input hash algorithm
- Updated struct rte_comp_op to input hash buffer

User in capability query will know about support hashes via
device info comp_feature_flag. If supported, application can initialize
desired algorithm enumeration in xform structure and pass valid hash
buffer during enqueue_burst().

Signed-off-by: Shally Verma <shally.verma@caviumnetworks.com>
Signed-off-by: Sunila Sahu <sunila.sahu@caviumnetworks.com>
Signed-off-by: Ashish Gupta <ashish.gupta@caviumnetworks.com>

compressdev: support stateful operations

Added stream data (stream) in compression operation,
which will contain the private data from each PMD
to support stateful operations.
Also, added functions to create/free this data.

Signed-off-by: Fiona Trahe <fiona.trahe@intel.com>
Signed-off-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
Signed-off-by: Shally Verma <shally.verma@caviumnetworks.com>
Signed-off-by: Ashish Gupta <ashish.gupta@caviumnetworks.com>

compressdev: support stateless operations

Added private transform data (priv_xform) in compression
operation, which will contain the private data from each
PMD to support stateless operations.
Also, added functions to create/free this data.

Signed-off-by: Fiona Trahe <fiona.trahe@intel.com>
Signed-off-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
Signed-off-by: Shally Verma <shally.verma@caviumnetworks.com>
Signed-off-by: Ashish Gupta <ashish.gupta@caviumnetworks.com>

compressdev: add operation management

Added functions to allocate and free compression operations.

Signed-off-by: Fiona Trahe <fiona.trahe@intel.com>
Signed-off-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
Signed-off-by: Shally Verma <shally.verma@caviumnetworks.com>
Signed-off-by: Ashish Gupta <ashish.gupta@caviumnetworks.com>

compressdev: add enqueue/dequeue functions

Signed-off-by: Fiona Trahe <fiona.trahe@intel.com>
Signed-off-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
Signed-off-by: Shally Verma <shally.verma@caviumnetworks.com>
Signed-off-by: Ashish Gupta <ashish.gupta@caviumnetworks.com>