dpdk.git
8 years agoi40evf: use base driver defined interface
Helin Zhang [Tue, 8 Mar 2016 08:14:37 +0000 (16:14 +0800)]
i40evf: use base driver defined interface

It removes the i40evf_set_mac_type() defined in PMD, and reuses
i40e_set_mac_type() defined in base driver.

Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Remy Horton <remy.horton@intel.com>
8 years agoi40e/base: add base driver release info
Helin Zhang [Tue, 8 Mar 2016 08:14:36 +0000 (16:14 +0800)]
i40e/base: add base driver release info

It adds base driver release information such as release date,
for better tracking in the future.

Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Remy Horton <remy.horton@intel.com>
8 years agoi40e/base: update AQ command structures and macros
Helin Zhang [Tue, 8 Mar 2016 08:14:35 +0000 (16:14 +0800)]
i40e/base: update AQ command structures and macros

Several structures and macros are added or updated, such
as 'struct i40e_aqc_get_link_status',
'struct i40e_aqc_run_phy_activity' and
'struct i40e_aqc_lldp_set_local_mib_resp'.

Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Remy Horton <remy.horton@intel.com>
8 years agoi40e/base: add AQ thermal sensor control struct
Helin Zhang [Tue, 8 Mar 2016 08:14:34 +0000 (16:14 +0800)]
i40e/base: add AQ thermal sensor control struct

It adds the new AQ command and struct for managing a
thermal sensor.

Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Remy Horton <remy.horton@intel.com>
8 years agoi40e/base: add virtchnl offload for X722 PCTYPES
Helin Zhang [Tue, 8 Mar 2016 08:14:33 +0000 (16:14 +0800)]
i40e/base: add virtchnl offload for X722 PCTYPES

X722 supports Expanded version of TCP, UDP PCTYPES for RSS.
Add a Virtchnl offload to support this.
Without this patch VF drivers will not be able to support
the correct PCTYPES for X722 and UDP flows will not fan out.

Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Remy Horton <remy.horton@intel.com>
8 years agoi40e/base: add some register definitions
Helin Zhang [Tue, 8 Mar 2016 08:14:32 +0000 (16:14 +0800)]
i40e/base: add some register definitions

This patch adds 7 new register definitions for programming the
parser, flow director and RSS blocks in the HW.

Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Remy Horton <remy.horton@intel.com>
8 years agoi40e: use AQ for Rx control register read/write
Helin Zhang [Tue, 8 Mar 2016 08:14:31 +0000 (16:14 +0800)]
i40e: use AQ for Rx control register read/write

RX control register read/write functions are added, as directly
read/write may fail when under stress small traffic. After the
adminq is ready, all rx control registers should be read/written
by dedicated functions.

Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Remy Horton <remy.horton@intel.com>
8 years agoi40e/base: fix coding style
Helin Zhang [Tue, 8 Mar 2016 08:14:30 +0000 (16:14 +0800)]
i40e/base: fix coding style

Clean up coding style in base code

Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Remy Horton <remy.horton@intel.com>
8 years agoi40e/base: save VSI resource count on update
Helin Zhang [Tue, 8 Mar 2016 08:14:29 +0000 (16:14 +0800)]
i40e/base: save VSI resource count on update

When updating a VSI, save off the number of allocated and
unallocated VSIs as we do when adding a VSI.

Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Remy Horton <remy.horton@intel.com>
8 years agoi40e/base: fix driver load failure
Helin Zhang [Tue, 8 Mar 2016 08:14:28 +0000 (16:14 +0800)]
i40e/base: fix driver load failure

Fix the driver load failure with linking with some
PHY types, as the amount of time it takes for the
GLGEN_RSTAT_DEVSTATE to be set increases greatly on those PHY
types, which can lead to a timeout.

Fixes: 9aeefed05538 ("i40e/base: support ESS")

Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Remy Horton <remy.horton@intel.com>
8 years agoi40e/base: avoid unwanted Tx traffic mirroring
Helin Zhang [Tue, 8 Mar 2016 08:14:27 +0000 (16:14 +0800)]
i40e/base: avoid unwanted Tx traffic mirroring

In Multi-Function Mode (MFP) particularly when the PF VSI is set
in limited promiscuous mode, the HW switch was still mirroring the
outgoing packets from other VSIs (VF/VMdq) onto the PF VSI.

This sets a new bit to avoid above mirroring, and it is in limited
promiscuous on the PF VSI in MFP which is similar to default port
VSI.

Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Remy Horton <remy.horton@intel.com>
8 years agoi40e/base: support LED blinking with new PHY
Helin Zhang [Tue, 8 Mar 2016 08:14:26 +0000 (16:14 +0800)]
i40e/base: support LED blinking with new PHY

This patch adds functions to blink led on devices using a new
PHY since MAC registers used in other designs do not work in
this device configuration.

Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Remy Horton <remy.horton@intel.com>
8 years agoi40e/base: add AQ switch configuration
Helin Zhang [Tue, 8 Mar 2016 08:14:25 +0000 (16:14 +0800)]
i40e/base: add AQ switch configuration

Add the support code for calling the AdminQ API call
aq_set_switch_config.

Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Remy Horton <remy.horton@intel.com>
8 years agoi40e/base: add VEB statistics control
Helin Zhang [Tue, 8 Mar 2016 08:14:24 +0000 (16:14 +0800)]
i40e/base: add VEB statistics control

With the latest firmware, statistics gathering can now be enabled and
disabled in the HW switch, so we need to add a parameter to allow the
driver to set it as desired. At the same time, the L2 cloud filtering
parameter has been removed as it was never used.

Older drivers working with the newer firmware and newer drivers working
with older firmware will not run into problems with these bits as the
defaults are reasonable and there is no overlap in the bit definitions.
Also, newer drivers will be forced to update because of the change in
function call parameters, a reminder that the functionality exists.

Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Remy Horton <remy.horton@intel.com>
8 years agoi40e/base: support mirroring rules
Helin Zhang [Tue, 8 Mar 2016 08:14:23 +0000 (16:14 +0800)]
i40e/base: support mirroring rules

This patch implements necessary functions related to port
mirroring features such as add/delete mirror rule, function
to set promiscuous VLAN mode for VSI if mirror rule_type is
"VLAN Mirroring".

Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Remy Horton <remy.horton@intel.com>
8 years agoi40e/base: set shared bit for multicast filters
Helin Zhang [Tue, 8 Mar 2016 08:14:22 +0000 (16:14 +0800)]
i40e/base: set shared bit for multicast filters

Add the use of the new shared MAC filter bit for multicast
and broadcast filters in order to make better use of the
filters available from the device.

Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Remy Horton <remy.horton@intel.com>
8 years agoi40e/base: fix PHY NVM interaction
Helin Zhang [Tue, 8 Mar 2016 08:14:21 +0000 (16:14 +0800)]
i40e/base: fix PHY NVM interaction

This patch fixes a problem where the NVMUpdate Tool, when
using the PHY NVM feature, gets bad data from the PHY because
of contention on the MDIO interface from get phy capability
calls from the driver during regular operations. The problem
is fixed by adding a check if media is available before calling
get phy capability function because that bit is not set when
device is in PHY interaction mode.

Fixes: 842ea1996335 ("i40e/base: save link module type")

Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Remy Horton <remy.horton@intel.com>
8 years agoi40e/base: unify the capability function
Helin Zhang [Tue, 8 Mar 2016 08:14:20 +0000 (16:14 +0800)]
i40e/base: unify the capability function

The device capabilities were defined in two places, and neither had
all the definitions. It really belongs with the AQ API definition,
so this patch removes the other set of definitions and fills out the
missing item.

Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Remy Horton <remy.horton@intel.com>
8 years agoi40e/base: fix proxy for X722
Helin Zhang [Tue, 8 Mar 2016 08:14:19 +0000 (16:14 +0800)]
i40e/base: fix proxy for X722

The recently added proxy opcodes should be available only with
X722_SUPPORT, so move them into the #ifdef, and reorder these
to be in numerical order with the rest of the opcodes. Several
structs that were added are unnecessary, so they are removed
here.

Fixes: 788fc17b2dec ("i40e/base: support proxy config for X722")

Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Remy Horton <remy.horton@intel.com>
8 years agoi40e/base: fix wake on lan for X722
Helin Zhang [Tue, 8 Mar 2016 08:14:18 +0000 (16:14 +0800)]
i40e/base: fix wake on lan for X722

The recently added Wakeup On Line (WOL) opcodes should be
available only with X722_SUPPORT, so move them into the #ifdef,
and reorder these to be in numerical order with the rest of the
opcodes. Several structs that were added are unnecessary, so
they are removed here.

Fixes: 3c89193a36fd ("i40e/base: support WOL config for X722")

Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Remy Horton <remy.horton@intel.com>
8 years agoi40e: update device ids
Helin Zhang [Tue, 8 Mar 2016 08:14:17 +0000 (16:14 +0800)]
i40e: update device ids

Add new Device ID's for backplane and QSFP+ adapters, and delete
deprecated one for backplane.

Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Remy Horton <remy.horton@intel.com>
8 years agoi40e/base: fix uncertain event descriptor issue
Helin Zhang [Tue, 8 Mar 2016 08:14:16 +0000 (16:14 +0800)]
i40e/base: fix uncertain event descriptor issue

In one obscure corner case, it was possible to clear the NVM update
wait flag when no update_done message was actually received. This
patch cleans the event descriptor before use, and moves the opcode
check to where it won't get done if there was no event to clean.

Fixes: 8db9e2a1b232 ("i40e: base driver")

Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Remy Horton <remy.horton@intel.com>
8 years agoi40e/base: set AQ count after memory allocation
Helin Zhang [Tue, 8 Mar 2016 08:14:15 +0000 (16:14 +0800)]
i40e/base: set AQ count after memory allocation

The standard way to check if the AQ is enabled is to look at
the count field. So it should only set this field after it has
successfully allocated memory.

Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Remy Horton <remy.horton@intel.com>
8 years agoi40e/base: fix missing check for stopped admin queue
Helin Zhang [Tue, 8 Mar 2016 08:14:14 +0000 (16:14 +0800)]
i40e/base: fix missing check for stopped admin queue

It's possible that while waiting for the spinlock, another
entity (that owns the spinlock) has shut down the admin queue.
If it then attempts to use the queue, it will panic.
It adds a check for this condition on the receive side. This
matches an existing check on the send queue side.

Fixes: 8db9e2a1b232 ("i40e: base driver")

Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Remy Horton <remy.horton@intel.com>
8 years agoi40e/base: limit version check of DCB
Helin Zhang [Tue, 8 Mar 2016 08:14:13 +0000 (16:14 +0800)]
i40e/base: limit version check of DCB

XL710/X710 devices requires FW version checks to properly handle
DCB configurations from the FW while other devices (e.g. X722)
do not, so limit these checks to XL710/X710 only.

Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Remy Horton <remy.horton@intel.com>
8 years agoi40e/base: support NVM read on X722
Helin Zhang [Tue, 8 Mar 2016 08:14:12 +0000 (16:14 +0800)]
i40e/base: support NVM read on X722

In X722, NVM reads can't be done through SRCTL registers.
And require AQ calls, which require grabbing the NVM lock.
Unfortunately some paths need the lock to be acquired once
and do a whole bunch of stuff and then release it.
This patch creates an unsafe version of the read calls, so
that it can be called from the paths that need the bulk access.

Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Remy Horton <remy.horton@intel.com>
8 years agoi40e/base: add flag for X722 register access
Helin Zhang [Tue, 8 Mar 2016 08:14:11 +0000 (16:14 +0800)]
i40e/base: add flag for X722 register access

Instead of doing the MAC check, use a flag that gets set per
MAC. This way there are less chances of user error and it
can enable multiple MACs with the capability in a single place
rather than cluttering the code with MAC checks.

Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Remy Horton <remy.horton@intel.com>
8 years agoi40e/base: acquire NVM ownership before reading it
Helin Zhang [Tue, 8 Mar 2016 08:14:10 +0000 (16:14 +0800)]
i40e/base: acquire NVM ownership before reading it

SW needs to acquire the NVM ownership before issuing an AQ read
to the X722 NVM otherwise it will get EBUSY from the firmware.
Also it should be released when done.

Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Remy Horton <remy.horton@intel.com>
8 years agoi40e/base: fix compilation warnings
Helin Zhang [Tue, 8 Mar 2016 08:14:09 +0000 (16:14 +0800)]
i40e/base: fix compilation warnings

Fix compilation warnings in base code on some platforms.

Fixes: bd6651c2d2d7 ("i40e/base: use bit shift macros")

Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Remy Horton <remy.horton@intel.com>
8 years agoi40evf: rework MAC address validation
Helin Zhang [Tue, 8 Mar 2016 06:42:09 +0000 (14:42 +0800)]
i40evf: rework MAC address validation

Use ether API of 'is_valid_assigned_ether_addr' to validate
MAC address.

Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Zhe Tao <zhe.tao@intel.com>
8 years agoi40e: generate MAC address for VF
Helin Zhang [Tue, 8 Mar 2016 06:42:08 +0000 (14:42 +0800)]
i40e: generate MAC address for VF

Generate a MAC address for each VF during PF host
initialization.

Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Zhe Tao <zhe.tao@intel.com>
8 years agoi40e: fix VLAN filtering
Julien Meunier [Thu, 4 Feb 2016 11:02:16 +0000 (12:02 +0100)]
i40e: fix VLAN filtering

VLAN filtering was always performed, even if hw_vlan_filter was
disabled. During device initialization, default filter
RTE_MACVLAN_PERFECT_MATCH was applied. In this situation, all incoming
VLAN frames were dropped by the card (increase of the register RUPP - Rx
Unsupported Protocol).

In order to restore default behavior, if HW VLAN filtering is activated,
set a filter to match MAC and VLAN. If not, set a filter to only match
MAC.

Fixes: 4861cde46116 ("i40e: new poll mode driver")
Fixes: 912b595146d6 ("i40e: mac vlan filter")

Signed-off-by: Julien Meunier <julien.meunier@6wind.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
8 years agoi40e: fix inverted check for no refcount
Rich Lane [Wed, 23 Dec 2015 08:08:00 +0000 (00:08 -0800)]
i40e: fix inverted check for no refcount

The no-refcount path was being taken without the application opting
in to it.

Fixes: 4861cde46116 ("i40e: new poll mode driver")

Reported-by: Mike Stolarchuk <mike.stolarchuk@bigswitch.com>
Signed-off-by: Rich Lane <rich.lane@bigswitch.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
8 years agoixgbe: disallow unsupported Rx mode
Jingjing Wu [Thu, 25 Feb 2016 07:33:34 +0000 (15:33 +0800)]
ixgbe: disallow unsupported Rx mode

The multi queue mode ETH_MQ_RX_VMDQ_DCB_RSS is not supported in
ixgbe driver.

Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
8 years agoixgbe: fix VF close to remove MAC address
Bernard Iremonger [Tue, 8 Mar 2016 17:10:27 +0000 (17:10 +0000)]
ixgbe: fix VF close to remove MAC address

Call the ixgbevf_remove_mac_addr() function in the ixgbevf_dev_close()
function to ensure that the VF traffic goes to the PF after stop,
close and detach of the VF.

Fixes: af75078fece3 ("first public release")

Signed-off-by: Bernard Iremonger <bernard.iremonger@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
8 years agoixgbe: add more information to multiqueue error message
Bernard Iremonger [Tue, 8 Mar 2016 17:10:26 +0000 (17:10 +0000)]
ixgbe: add more information to multiqueue error message

Add the nb_rx_q and nb_tx_q values to the error message
to give details about the error.

Fixes: 27b609cbd1c6 ("ethdev: move the multi-queue mode check to specific drivers")

Signed-off-by: Bernard Iremonger <bernard.iremonger@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
8 years agoixgbe: fix releasing queues twice when detaching VF
Bernard Iremonger [Tue, 8 Mar 2016 17:10:25 +0000 (17:10 +0000)]
ixgbe: fix releasing queues twice when detaching VF

Releasing the rx and tx queues is already done in ixgbe_dev_close()
so it does not need to be done in eth_ixgbevf_dev_uninit().

Fixes: 2866c5f1b87e ("ixgbe: support port hotplug")

Signed-off-by: Bernard Iremonger <bernard.iremonger@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
8 years agoixgbe: fix VF Rx/Tx function assignment
Zhe Tao [Thu, 10 Mar 2016 15:26:22 +0000 (15:26 +0000)]
ixgbe: fix VF Rx/Tx function assignment

For the secondary process of DPDK to initialize ixgbevf, it will always
use the simple RX function or LRO RX function, and this behavior is not
the same RX/TX function selection logic as it is for the primary process.
Use the ixgbe_set_tx_function and ixgbe_set_rx_function to select the
RX/TX function when secondary process calls the init function for eth dev.

Fixes: 9d8a92628f21 ("ixgbe: remove simple scalar scattered Rx method")

Signed-off-by: Zhe Tao <zhe.tao@intel.com>
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
8 years agoixgbe: support link speed auto-negotiation on X550em_x
Wenzhuo Lu [Fri, 26 Feb 2016 03:05:29 +0000 (11:05 +0800)]
ixgbe: support link speed auto-negotiation on X550em_x

Normally the auto-negotiation is supported by FW. SW need not care about
that. But on x550em_x, FW doesn't support auto-neg. As the x550em_x ports
are 10G, if we connect the port will a peer which is 1G, the link will
always be down.
We need support auto-neg by SW to avoid this link down issue. As we already
have the code to handle the link speed setting, what we need is a trigger.
When the advertised link speed changes, a PHY interruption will be
triggered. So, we should handle this interrupt and call ixgbe_handle_lasi
to set the link speed correctly.

Please be aware it's working when auto-neg is on. If the auto-neg of the
peer port is turned off and its speed is indicated manually, we should also
set the speed of our own port manually.

Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Shaopeng He <shaopeng.he@intel.com>
8 years agoixgbe: support multicast promiscuous mode on VF
Wenzhuo Lu [Sun, 14 Feb 2016 06:24:47 +0000 (14:24 +0800)]
ixgbe: support multicast promiscuous mode on VF

Add multicast promiscuous mode support on ixgbe VF driver.

Please note if we want to use this promiscuous mode, we need both PF
and VF driver to support it. The reason is this VF feature is
configged on PF.
If use kernel PF driver + dpdk VF driver, make sure kernel PF driver
support VF multicast promiscuous mode. If use dpdk PF + dpdk VF,
better make sure PF driver is the same version as VF.

Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Shaopeng He <shaopeng.he@intel.com>
Acked-by: Xiao Wang <xiao.w.wang@intel.com>
8 years agoixgbe: support new devices and MAC types
Wenzhuo Lu [Sun, 14 Feb 2016 08:55:06 +0000 (16:55 +0800)]
ixgbe: support new devices and MAC types

Add the support for new devices and mac types, as supported by the base
code update.

Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
8 years agoixgbe/base: update readme
Wenzhuo Lu [Sun, 14 Feb 2016 08:55:05 +0000 (16:55 +0800)]
ixgbe/base: update readme

Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
8 years agoixgbe/base: abstract out link read/write
Wenzhuo Lu [Sun, 14 Feb 2016 08:55:04 +0000 (16:55 +0800)]
ixgbe/base: abstract out link read/write

It's more valuable to abstract the link read/write interface. As such,
change the following method names, and add them to a new link info
structure:
  read_i2c_combined               => read_link
  read_i2c_combined_unlocked      => read_link_unlocked
  write_i2c_combined              => write_link
  write_i2c_combined_unlocked     => write_link_unlocked

This will allow X550EM_a to override these methods for MDIO access
while X550EM_x provides methods to use I2C combined access.
Initially the structure is just method pointers and a bus
address.

Two functions involved in combined I2C accesses were moved from
ixgbe_phy.c to ixgbe_x550.c. The underlying functions that carry
out the combined I2C accesses were left in ixgbe_phy.c because
they share some functions with other I2C methods.

Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
8 years agoixgbe/base: set MDIO speed after MAC reset
Wenzhuo Lu [Sun, 14 Feb 2016 08:55:03 +0000 (16:55 +0800)]
ixgbe/base: set MDIO speed after MAC reset

The MDIO clock speed must be reconfigured after the MAC reset.
The MDIO clock speed becomes invalid, therefore the driver reads
invalid PHY register values. The driver now set the MDIO clock
speed prior to initializing PHY ops and again after the MAC reset.

As now the MDIO speed gets set in more than one place, make a
function for it so it will always be done correctly.

Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
8 years agoixgbe/base: fix setting flow director flag twice
Wenzhuo Lu [Sun, 14 Feb 2016 08:55:02 +0000 (16:55 +0800)]
ixgbe/base: fix setting flow director flag twice

Do not set FDIRCTRL.DROP_NO_MATCH in ixgbe_init_fdir_perfect_82599(),
this bit is already set in ixgbe_set_fdir_drop_queue_82599() which
makes more sense for drivers that call that function.

This resolves an issue where packets were being dropped when switching
to perfect filters mode.

Setting this bit makes no sense in perfect filters mode for the
driver as we do not want to route all packets that don't match an FDIR
rule to a single queue and instead fall back to RSS.
Drivers that need this bit set can call ixgbe_set_fdir_drop_queue_82599()
and the ones that don't, can preserve the old behavior.

Fixes: 2241ce281646 ("ixgbe/base: add flow director drop queue")
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
8 years agoixgbe/base: add register definition for SGMII busy
Wenzhuo Lu [Sun, 14 Feb 2016 08:55:01 +0000 (16:55 +0800)]
ixgbe/base: add register definition for SGMII busy

The X550EM_a device provides the MAC_SGMII_BUSY register to
indicate when slow SGMII register writes complete. Add
definitions for the register. No definitions are provided for
the individual bits under the theory that it is better to wait
for everything to complete when needed rather than try to map
out which reads need to wait for which writes. So we should wait
when anything is marked as "busy".

Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
8 years agoixgbe/base: ignore manageability for PHY power on
Wenzhuo Lu [Sun, 14 Feb 2016 08:55:00 +0000 (16:55 +0800)]
ixgbe/base: ignore manageability for PHY power on

Instead of not defining the callback for set_phy_power when
manageability is enabled, put the check in the set_phy_power
function so that only turning the power off is conditional on
management, but not turning the PHY on.

Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
8 years agoixgbe/base: set VF MAC address only when acked by PF
Wenzhuo Lu [Sun, 14 Feb 2016 08:54:59 +0000 (16:54 +0800)]
ixgbe/base: set VF MAC address only when acked by PF

This patch resolves an issue where VF mac address is zeroed out
in cases where the VF driver is loaded while the PF interface
is down.
The solution is to only set it when we get an ACK from the PF.

Fixes: 6202266e5680 ("ixgbe/base: vf changes")
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
8 years agoixgbe/base: add sw-firmware sync for resource sharing on X550em_a
Wenzhuo Lu [Sun, 14 Feb 2016 08:54:58 +0000 (16:54 +0800)]
ixgbe/base: add sw-firmware sync for resource sharing on X550em_a

Use a PHY token, shared between sw-fw for PHY access on X550EM_a.

Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
8 years agoixgbe/base: support X550em_x V2 device
Wenzhuo Lu [Sun, 14 Feb 2016 08:54:57 +0000 (16:54 +0800)]
ixgbe/base: support X550em_x V2 device

Only x550em_x V1 was supported before. Now V2 is supported.
A mask for V1 and V2 is defined and used to support both.

Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
8 years agoixgbe/base: support X550em_a device
Wenzhuo Lu [Sun, 14 Feb 2016 08:54:56 +0000 (16:54 +0800)]
ixgbe/base: support X550em_a device

Add new X550EM_a devices and their mac types, X550EM_a
and X550EM_a_vf.
Update the code to use the new devices and mac types.

Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
8 years agoixgbe: fix disable interrupt twice
Michael Qiu [Fri, 29 Jan 2016 05:58:10 +0000 (13:58 +0800)]
ixgbe: fix disable interrupt twice

Currently, ixgbe vf and pf will disable interrupt twice in
stop stage and uninit stage. It will cause an error:

    testpmd> quit

    Shutting down port 0...
    Stopping ports...
    Done
    Closing ports...
    EAL: Error disabling MSI-X interrupts for fd 26
    Done

because the interrupt has already been disabled in stop stage.
Since it is enabled in init stage, better remove from
stop stage.

Fixes: 0eb609239efd ("ixgbe: enable Rx queue interrupts for PF and VF")

Signed-off-by: Michael Qiu <michael.qiu@intel.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
8 years agoixgbe: fix whitespace
Stephen Hemminger [Wed, 13 Jan 2016 04:54:10 +0000 (20:54 -0800)]
ixgbe: fix whitespace

Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Helin Zhang <helin.zhang@intel.com>
8 years agoixgbe: speed up non-vector Tx
Stephen Hemminger [Fri, 13 Nov 2015 16:10:13 +0000 (08:10 -0800)]
ixgbe: speed up non-vector Tx

The freeing of mbuf's in ixgbe is one of the observable hot spots
under load. Optimize it by doing bulk free of mbufs using code similar
to i40e and fm10k.

Drop the no longer needed micro-optimization for the no refcount flag.

Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
8 years agoigb: set default thresholds based on MAC type
Stephen Hemminger [Fri, 22 Jan 2016 01:38:37 +0000 (17:38 -0800)]
igb: set default thresholds based on MAC type

This brings the DPDK igb driver inline with the behavior used by
the current Linux driver. The IGB hardware has several different
MAC types and the threshold values that work vary based on the hardware.

Since DPDK 1.8 it has been up to devices to provide the correct default
configuration parameter. But the igb driver gives values that are broken
on some devices, and always causes a warning message at startup.

Please test this on real hardware, I don't have the luxury of a
hardware lab full of variations of this chip.

Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
8 years agoe1000: fix VF MAC address on close
Bernard Iremonger [Wed, 2 Mar 2016 16:09:06 +0000 (16:09 +0000)]
e1000: fix VF MAC address on close

Allow reprogramming of the RAR with a zero mac address,
to ensure that the VF traffic goes to the PF after
stop, close and detach of the VF.

Fixes: be2d648a2dd3 ("igb: add PF support")
Fixes: d82170d27918 ("igb: add VF support")

Signed-off-by: Bernard Iremonger <bernard.iremonger@intel.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
8 years agoe1000: support VF promiscuous and allmulticast
Yury Kylulin [Tue, 9 Feb 2016 09:09:43 +0000 (12:09 +0300)]
e1000: support VF promiscuous and allmulticast

Enable promiscuous and allmulticast mode control from the VF using
rte_eth_promiscuous_enable()/rte_eth_promiscuous_disable() and
rte_eth_allmulticast_enable()/rte_eth_allmulticast_disable().

For promiscuous mode host/PF igb driver should be built with
IGB_ENABLE_VF_PROMISC.

For allmulticast mode "allmulti" flag should be set for appropriate PF
ifconfig eth0 allmulti

Signed-off-by: Yury Kylulin <yury.kylulin@intel.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
8 years agoe1000: support I217 and I218 devices
Ravi Kerur [Wed, 2 Mar 2016 13:59:34 +0000 (05:59 -0800)]
e1000: support I217 and I218 devices

Modified driver and eal code to support I217 and I218 Intel NICs.

Compiled and tested (via testpmd) on Ubuntu 14.04 for target
x86_64-native-linuxapp-gcc
Compiled for target x86_64-native-linuxapp-clang

Signed-off-by: Ravi Kerur <rkerur@gmail.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
8 years agoenic: fix last packet not being sent
John Daley [Tue, 8 Mar 2016 18:49:07 +0000 (10:49 -0800)]
enic: fix last packet not being sent

The last packet of the tx burst function array was not being
emitted until the subsequent call.  The nic descriptor index
was being set to the current tx descriptor instead of one past
the descriptor as required by the nic.

Fixes: d739ba4c6abf ("enic: improve Tx packet rate")

Signed-off-by: John Daley <johndale@cisco.com>
8 years agoenic: improve Rx performance
John Daley [Fri, 4 Mar 2016 21:09:00 +0000 (13:09 -0800)]
enic: improve Rx performance

This is a wholesale replacement of the Enic PMD receive path in order
to improve performance and code clarity. The changes are:
- Simplify and reduce code path length of receive function.
- Put most of the fast-path receive functions in one file.
- Reduce the number of posted_index updates (pay attention to
  rx_free_thresh)
- Remove the unneeded container structure around the RQ mbuf ring
- Prefetch next Mbuf and descriptors while processing the current one
- Use a lookup table for converting CQ flags to mbuf flags.

Signed-off-by: John Daley <johndale@cisco.com>
8 years agoenic: fix DMA address of outgoing packets
Yoann Desmouceaux [Wed, 24 Feb 2016 23:06:15 +0000 (00:06 +0100)]
enic: fix DMA address of outgoing packets

The enic PMD driver send function uses a constant offset instead
of relying on the data_off in the mbuf to find the start of the packet.

Fixes: fefed3d1e62c ("enic: new driver")

Signed-off-by: Yoann Desmouceaux <ydesmouc@cisco.com>
Acked-by: Bruce Richardson <bruce.richardson@intel.com>
8 years agocxgbe: fix PCI info copy to ports under same PF
Rahul Lakkireddy [Thu, 25 Feb 2016 09:37:53 +0000 (15:07 +0530)]
cxgbe: fix PCI info copy to ports under same PF

Chelsio NIC ports share a single PF. Move rte_eth_copy_pci_info()
to copy the pci device information to the remaining ports as well.

Also update license year to 2016.

Fixes: eeefe73f0af1 ("drivers: copy PCI device info to ethdev data")

Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
8 years agocxgbe: fix memory leak after initialization failure
Rahul Lakkireddy [Fri, 12 Feb 2016 11:45:30 +0000 (17:15 +0530)]
cxgbe: fix memory leak after initialization failure

Add missing code to free adapter when the device initialization fails.

Fixes: 8318984927ff ("cxgbe: add pmd skeleton")

Reported-by: Seth Arnold <seth.arnold@canonical.com>
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
8 years agocxgbe: fix setting wrong MTU
Rahul Lakkireddy [Tue, 19 Jan 2016 10:17:08 +0000 (15:47 +0530)]
cxgbe: fix setting wrong MTU

max_rx_pkt_len already includes ETHER_HDR_LEN and ETHER_CRC_LEN for the
mtu. But, the firmware also adds ETHER_HDR_LEN and ETHER_CRC_LEN to the
mtu specified. Fix by subtracting these values from the mtu before
passing it to firmware.

Fixes: 4b2eff452d2e ("cxgbe: enable jumbo frames")

Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
8 years agocxgbe: fix allocated size for RSS table
Rahul Lakkireddy [Tue, 19 Jan 2016 10:17:07 +0000 (15:47 +0530)]
cxgbe: fix allocated size for RSS table

The size of each entry in the port's rss table is actually 2 bytes
and not 1 byte. A segfault occurs when accessing part of port 0's rss
table because it gets overwritten by subsequent port 1's part of the
rss table. Fix by setting the size of each entry appropriately.

Fixes: 92c8a63223e5 ("cxgbe: add device configuration and Rx support")

Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
8 years agobnx2x: determine queue sizes sooner
Charles (Chas) Williams [Thu, 31 Dec 2015 00:37:51 +0000 (19:37 -0500)]
bnx2x: determine queue sizes sooner

The VF needs to determine the queues sizes before .dev_infos_get
so that it can hint to the upper layer the proper sizes.  Move
bnx2x_vf_get_resources() to .eth_dev_init and probe with the guesses
from bnx2x_init_rte().

Signed-off-by: Chas Williams <3chas3@gmail.com>
Acked-by: Rasesh Mody <rasesh.mody@qlogic.com>
8 years agobnx2x: fix resource allocattion error handling
Charles (Chas) Williams [Thu, 31 Dec 2015 00:37:50 +0000 (19:37 -0500)]
bnx2x: fix resource allocattion error handling

bnx2x_loop_obtain_resources() returns a struct containing the status and
the error message.  If bnx2x_do_req4pf() fails, it shouldn't return both
of these fields set to 0 indicating failure and no error.

Further, bnx2x_do_req4pf() needs to be able fail and return NO_RESOURCES
so that bnx2x_loop_obtain_resources() can negotiate reduced resource
requirments.  This requires additional checking around bnx2x_do_req4pf().

Fixes: 540a211084a7 ("bnx2x: driver core")

Signed-off-by: Chas Williams <3chas3@gmail.com>
Acked-by: Rasesh Mody <rasesh.mody@qlogic.com>
8 years agobnx2x: remove unused variable
Stephen Hemminger [Tue, 5 Jan 2016 16:32:00 +0000 (08:32 -0800)]
bnx2x: remove unused variable

The mbuf_alloc_size is leftover from BSD or some other code base.
It is set but never used in DPDK driver.  After that the related defines
can also be eliminated.

Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Harish Patil <harish.patil@qlogic.com>
8 years agompipe: fix crash when testpmd is quit under load
Liming Sun [Wed, 10 Feb 2016 05:15:21 +0000 (00:15 -0500)]
mpipe: fix crash when testpmd is quit under load

Fixes: the hung/crash issue when quitting testpmd under high
traffic rate. The following issue were found and fixed.
1. edesc->size is not initialized properly in mpipe_do_xmit() and could
   cause buffer leak or corruption when HW buffer return is used.
2. Check the 'idesc.be' error bit in mpipe_recv_flush() to make sure
   buffer is valid before releasing it. This is to avoid issues when
   running out of buffers.
3. priv->rx_buffers counter is not accurate when HW buffer return is
   used. Remove this counter to simplify the code.

Signed-off-by: Liming Sun <lsun@ezchip.com>
Acked-by: Zhigang Lu <zlu@ezchip.com>
8 years agompipe: fix link initialization ordering
Liming Sun [Fri, 8 Jan 2016 14:30:38 +0000 (09:30 -0500)]
mpipe: fix link initialization ordering

Mpipe link structure is initialized in function mpipe_link_init().
Currently it's only called from the eth_dev_ops.dev_start, which
caused crashes when link mgmt APIs (like promiscuous_enable)
was called before eth_dev_ops.dev_start(). This submit fixed it
by calling mpipe_link_init() in rte_pmd_mpipe_devinit().

Fixes: a8dd50513dea ("mpipe: add TILE-Gx mPIPE poll mode driver")

Signed-off-by: Liming Sun <lsun@ezchip.com>
Acked-by: Zhigang Lu <zlu@ezchip.com>
8 years agompipe: optimize buffer return mechanism
Liming Sun [Fri, 8 Jan 2016 14:30:37 +0000 (09:30 -0500)]
mpipe: optimize buffer return mechanism

This submit has changes to optimize the mpipe buffer return. When
a packet is received, instead of allocating and refilling the
buffer stack right away, it tracks the number of pending buffers,
and use HW buffer return as an optimization when the pending
number is below certain threshold, thus save two MMIO writes and
improves performance especially for bidirectional traffic case.

Signed-off-by: Liming Sun <lsun@ezchip.com>
Acked-by: Zhigang Lu <zlu@ezchip.com>
8 years agomk: support native build on TILE-Gx
Liming Sun [Fri, 8 Jan 2016 14:30:36 +0000 (09:30 -0500)]
mk: support native build on TILE-Gx

The CROSS variable has empty default value (for native) and
must be set when using a cross-toolchain.

Signed-off-by: Liming Sun <lsun@ezchip.com>
Acked-by: Zhigang Lu <zlu@ezchip.com>
8 years agodoc: fix IPsec entry in the release notes
Thomas Monjalon [Tue, 15 Mar 2016 18:43:55 +0000 (19:43 +0100)]
doc: fix IPsec entry in the release notes

It was inserted in the "Resolved Issues" section.
Move the entry with the new features.

Signed-off-by: Thomas Monjalon <thomas.monjalon@6wind.com>
8 years agovhost: fix default value of kickfd and callfd
Tetsuya Mukawa [Mon, 14 Mar 2016 08:53:32 +0000 (17:53 +0900)]
vhost: fix default value of kickfd and callfd

Currently, default values of kickfd and callfd are -1.
If the values are -1, current code guesses kickfd and callfd haven't
been initialized yet. Then vhost library will guess the virtqueue isn't
ready for processing.

But callfd and kickfd will be set as -1 when "--enable-kvm"
isn't specified in QEMU command line. It means we cannot treat -1 as
uninitialized state.

The patch defines -1 and -2 as VIRTIO_INVALID_EVENTFD and
VIRTIO_UNINITIALIZED_EVENTFD, and uses VIRTIO_UNINITIALIZED_EVENTFD for
the default values of kickfd and callfd.

Signed-off-by: Tetsuya Mukawa <mukawa@igel.co.jp>
Acked-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
8 years agovhost: avoid dead loop chain
Yuanhan Liu [Thu, 10 Mar 2016 04:32:46 +0000 (12:32 +0800)]
vhost: avoid dead loop chain

If a malicious guest forges a dead loop chain, it could lead to a dead
loop of copying the desc buf to mbuf, which results to all mbuf being
exhausted.

Add a var nr_desc to avoid such case.

Suggested-by: Huawei Xie <huawei.xie@intel.com>
Signed-off-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
8 years agovhost: check for ring descriptors overflow
Yuanhan Liu [Thu, 10 Mar 2016 04:32:45 +0000 (12:32 +0800)]
vhost: check for ring descriptors overflow

A malicious guest may easily forge some illegal vring desc buf.
To make our vhost robust, we need make sure desc->next will not
go beyond the vq->desc[] array.

Suggested-by: Rich Lane <rich.lane@bigswitch.com>
Signed-off-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
8 years agovhost: do sanity check for ring descriptor length
Yuanhan Liu [Thu, 10 Mar 2016 04:32:44 +0000 (12:32 +0800)]
vhost: do sanity check for ring descriptor length

We need make sure that desc->len is bigger than the size of virtio net
header, otherwise, unexpected behaviour might happen due to "desc_avail"
would become a huge number with for following code:

desc_avail  = desc->len - vq->vhost_hlen;

For dequeue code path, it will try to allocate enough mbuf to hold such
size of desc buf, which ends up with consuming all mbufs, leading to no
free mbuf is available. Therefore, you might see an error message:

Failed to allocate memory for mbuf.

Also, for both dequeue/enqueue code path, while it copies data from/to
desc buf, the big "desc_avail" would result to access memory not belong
the desc buf, which could lead to some potential memory access errors.

A malicious guest could easily forge such malformed vring desc buf. Every
time we restart an interrupted DPDK application inside guest would also
trigger this issue, as all huge pages are reset to 0 during DPDK re-init,
leading to desc->len being 0.

Therefore, this patch does a sanity check for desc->len, to make vhost
robust.

Reported-by: Rich Lane <rich.lane@bigswitch.com>
Signed-off-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
8 years agovhost: remove wrong unlikely prediction in Rx
Yuanhan Liu [Thu, 10 Mar 2016 04:32:43 +0000 (12:32 +0800)]
vhost: remove wrong unlikely prediction in Rx

VIRTIO_NET_F_MRG_RXBUF is a default feature supported by vhost.
Adding unlikely for VIRTIO_NET_F_MRG_RXBUF detection doesn't
make sense to me at all.

Signed-off-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
8 years agovhost: remove rte_memcpy from header copy
Yuanhan Liu [Thu, 10 Mar 2016 04:32:42 +0000 (12:32 +0800)]
vhost: remove rte_memcpy from header copy

First of all, rte_memcpy() is mostly useful for copying big packets
by leveraging hardware advanced instructions like AVX. But for virtio
net hdr, which is 12 bytes at most, invoking rte_memcpy() will not
introduce any performance boost.

And, to my suprise, rte_memcpy() is VERY huge. Since rte_memcpy()
is inlined, it increases the binary code size linearly every time
we call it at a different place. Replacing the two rte_memcpy()
with directly copy saves nearly 12K bytes of code size!

Signed-off-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
8 years agovhost: refactor mergeable Rx
Yuanhan Liu [Mon, 14 Mar 2016 07:35:22 +0000 (15:35 +0800)]
vhost: refactor mergeable Rx

Current virtio_dev_merge_rx() implementation just looks like the
old rte_vhost_dequeue_burst(), full of twisted logic, that you
can see same code block in quite many different places.

However, the logic of virtio_dev_merge_rx() is quite similar to
virtio_dev_rx().  The big difference is that the mergeable one
could allocate more than one available entries to hold the data.
Fetching all available entries to vec_buf at once makes the
difference a bit bigger then.

The refactored code looks like below:

while (mbuf_has_not_drained_totally || mbuf_has_next) {
if (this_desc_has_no_room) {
this_desc = fetch_next_from_vec_buf();

if (it is the last of a desc chain)
update_used_ring();
}

if (this_mbuf_has_drained_totally)
mbuf = fetch_next_mbuf();

COPY(this_desc, this_mbuf);
}

This patch reduces quite many lines of code, therefore, make it much
more readable.

Signed-off-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
8 years agovhost: refactor Rx
Yuanhan Liu [Thu, 10 Mar 2016 04:32:40 +0000 (12:32 +0800)]
vhost: refactor Rx

This is a simple refactor, as there isn't any twisted logic in old
code. Here I just broke the code and introduced two helper functions,
reserve_avail_buf() and copy_mbuf_to_desc() to make the code more
readable.

Also, it saves nearly 1K bytes of binary code size.

Signed-off-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
8 years agovhost: refactor dequeueing
Yuanhan Liu [Thu, 10 Mar 2016 04:32:39 +0000 (12:32 +0800)]
vhost: refactor dequeueing

The current rte_vhost_dequeue_burst() implementation is a bit messy
and logic twisted. And you could see repeat code here and there.

However, rte_vhost_dequeue_burst() acutally does a simple job: copy
the packet data from vring desc to mbuf. What's tricky here is:

- desc buff could be chained (by desc->next field), so that you need
  fetch next one if current is wholly drained.

- One mbuf could not be big enough to hold all desc buff, hence you
  need to chain the mbuf as well, by the mbuf->next field.

The simplified code looks like following:

while (this_desc_is_not_drained_totally || has_next_desc) {
if (this_desc_has_drained_totally) {
this_desc = next_desc();
}

if (mbuf_has_no_room) {
mbuf = allocate_a_new_mbuf();
}

COPY(mbuf, desc);
}

Note that the old patch does a special handling for skipping virtio
header. However, that could be simply done by adjusting desc_avail
and desc_offset var:

desc_avail  = desc->len - vq->vhost_hlen;
desc_offset = vq->vhost_hlen;

This refactor makes the code much more readable (IMO), yet it reduces
binary code size.

Signed-off-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
8 years agovirtio: fix query of legacy features
Yuanhan Liu [Thu, 10 Mar 2016 07:01:20 +0000 (15:01 +0800)]
virtio: fix query of legacy features

Declare dst as type uint32_t instead of uint64_t, otherwise, we will get
a random upper 32 bit feature bits, as the following io port read reads
lower 32 bit only. It could lead a feature bits that include VIRTIO_F_VERSION_1
(the 32th bit) for legacy virtio, which is obviously wrong.

Fixes: b8f04520ad71 ("virtio: use PCI ioport API")

Signed-off-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Acked-by: Jianfeng Tan <jianfeng.tan@intel.com>
Reviewed-by: David Marchand <david.marchand@6wind.com>
8 years agoeal: decrease log level of some debug messages
Keith Wiles [Thu, 10 Sep 2015 19:40:50 +0000 (14:40 -0500)]
eal: decrease log level of some debug messages

When log level is set to 7 (INFO) these messages are still displayed
and should be set to DEBUG.

Signed-off-by: Keith Wiles <keith.wiles@intel.com>
8 years agosched: eliminate floating point in calculating byte clock
Stephen Hemminger [Sun, 29 Nov 2015 18:46:49 +0000 (10:46 -0800)]
sched: eliminate floating point in calculating byte clock

The old code was doing a floating point divide for each rte_dequeue()
which is very expensive. Change to using fixed point scaled inverse
multiply. To maintain equivalent precision, scaled math is used.
The application ABI is the same.

This improved performance from 5Gbit/sec to 10 Gbit/sec when configured
for 10 Gbit/sec rate.

Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
8 years agosched: introduce reciprocal divide
Stephen Hemminger [Sun, 29 Nov 2015 18:46:48 +0000 (10:46 -0800)]
sched: introduce reciprocal divide

This adds (with permission of the original author)
reciprocal divide based on algorithm in Linux.

Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
8 years agosched: keep track of RED drops
Stephen Hemminger [Sun, 29 Nov 2015 18:46:47 +0000 (10:46 -0800)]
sched: keep track of RED drops

Add new statistic to keep track of drops due to RED.

Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
8 years agomk: fix eal shared library dependencies
Panu Matilainen [Thu, 10 Mar 2016 13:16:01 +0000 (15:16 +0200)]
mk: fix eal shared library dependencies

Add DT_NEEDED entries for librte_eal external dependencies.
Details between the platforms differ somewhat, and for static
builds they need to be handled from mk/exec-env still.

Signed-off-by: Panu Matilainen <pmatilai@redhat.com>
8 years agomk: fix vhost shared library dependencies
Panu Matilainen [Thu, 10 Mar 2016 13:16:00 +0000 (15:16 +0200)]
mk: fix vhost shared library dependencies

Add DT_NEEDED entries for external library dependencies which
are the most critical ones for sane operation.
Clean up vhost_cuse CFLAGS/LDFLAGS confusion while at it.

Signed-off-by: Panu Matilainen <pmatilai@redhat.com>
8 years agomk: fix shared library dependencies on libm and librt
Panu Matilainen [Thu, 10 Mar 2016 13:15:59 +0000 (15:15 +0200)]
mk: fix shared library dependencies on libm and librt

There are two places that need -lm (test app and librte_sched) and
exactly one that needs -lrt (librte_sched). Add the relevant
DT_NEEDED entries to both, and eliminate the bogus discrepancy
between Linux and BSD EXECENV_LDLIBS wrt these libs.

Signed-off-by: Panu Matilainen <pmatilai@redhat.com>
8 years agoapp/testpmd: support unidirectional configuration
Reshma Pattan [Fri, 11 Mar 2016 15:16:55 +0000 (15:16 +0000)]
app/testpmd: support unidirectional configuration

Added testpmd support to validate zero nb_rxq/nb_txq
changes of ethdev (d505ba8).

Signed-off-by: Reshma Pattan <reshma.pattan@intel.com>
Acked-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
8 years agoexamples/ip_pipeline: use unsigned constants for left shift operations
Panu Matilainen [Thu, 10 Mar 2016 13:49:55 +0000 (15:49 +0200)]
examples/ip_pipeline: use unsigned constants for left shift operations

Tell the compiler to use unsigned constants for left shift ops,
otherwise building with gcc >= 6.0 fails due to multiple warnings like:
warning: left shift of negative value [-Wshift-negative-value]

Signed-off-by: Panu Matilainen <pmatilai@redhat.com>
Acked-by: Cristian Dumitrescu <cristian.dumitrescu@intel.com>
8 years agoexamples/ip_pipeline: add load balancing to pass-through
Jasvinder Singh [Thu, 10 Mar 2016 15:29:02 +0000 (15:29 +0000)]
examples/ip_pipeline: add load balancing to pass-through

The pass-through pipeline implementation is extended with load balancing
function. This function allows uniform distribution of the packets among
its output ports. For packets distribution, any application level logic
can be applied. For instance, in this implementation, hash value
computed over specific header fields of the incoming packets has been
used to spread traffic uniformly among the output ports.

The following pass-through configuration can be used for implementing
load balancing function over ipv4 traffic;

[PIPELINE0]
type = PASS-THROUGH
core = 0
pktq_in = RXQ0.0 RXQ1.0 RXQ2.0 RXQ3.0
pktq_out = TXQ0.0 TXQ1.0 TXQ2.0 TXQ3.0
dma_src_offset = 278; mbuf (128) + headroom (128) + 1st ethertype offset (14) + ttl offset within ip header = 278 (ipv4)
dma_dst_offset = 128; mbuf (128)
dma_size = 16
dma_src_mask = 00FF0000FFFFFFFFFFFFFFFFFFFFFFFF
dma_hash_offset = 144; (dma_dst_offset+dma_size)
lb = hash

Signed-off-by: Jasvinder Singh <jasvinder.singh@intel.com>
Acked-by: Cristian Dumitrescu <cristian.dumitrescu@intel.com>
8 years agoexamples/ip_pipeline: add pcap file dump
Fan Zhang [Fri, 11 Mar 2016 17:08:10 +0000 (17:08 +0000)]
examples/ip_pipeline: add pcap file dump

This patch add packet dumping feature to ip_pipeline. Output port type
SINK now supports dumping packets to PCAP file before releasing mbuf back
to mempool. This feature can be applied by specifying parameters in
configuration file as shown below:

[PIPELINE1]
type = PASS-THROUGH
core = 1
pktq_in = SOURCE0 SOURCE1
pktq_out = SINK0 SINK1
pcap_file_wr = /path/to/eth1.pcap /path/to/eth2.pcap
pcap_n_pkt_wr = 80 0

The configuration section "pcap_file_wr" contains full path and name of
the PCAP file which the packets will be dumped to. If multiple SINKs
exists, each shall have its own PCAP file path listed in this section,
separated by spaces. Multiple SINK ports shall NOT share same PCAP file to
be dumped.

The configuration section "pcap_n_pkt_wr" contains integer value(s)
and indicates the maximum number of packets to be dumped to the PCAP file.
If this value is "0", the "infinite" dumping mode will be used. If this
value is N (N > 0), the dumping will be finished when the number of
packets dumped to the file reaches N.

To enable PCAP dumping support to IP pipeline, the compiler option
CONFIG_RTE_PORT_PCAP must be set to 'y'. It is possible to disable this
feature by removing "pcap_file_wr" and "pcap_n_pkt_wr" lines from the
configuration file.

Signed-off-by: Fan Zhang <roy.fan.zhang@intel.com>
Acked-by: Cristian Dumitrescu <cristian.dumitrescu@intel.com>
8 years agoport: add pcap file dump
Fan Zhang [Fri, 11 Mar 2016 17:08:09 +0000 (17:08 +0000)]
port: add pcap file dump

Originally, sink ports in librte_port releases received mbufs back to
mempool. This patch adds optional packet dumping to PCAP feature in sink
port: the packets will be dumped to user defined PCAP file for storage or
debugging. The user may also choose the sink port's activity: either it
continuously dump the packets to the file, or stops at certain dumping

This feature shares same CONFIG_RTE_PORT_PCAP compiler option as source
port PCAP file support feature. Users can enable or disable this feature
by setting CONFIG_RTE_PORT_PCAP compiler option "y" or "n".

Signed-off-by: Fan Zhang <roy.fan.zhang@intel.com>
Acked-by: Cristian Dumitrescu <cristian.dumitrescu@intel.com>
8 years agoexamples/ip_pipeline: add pcap file source
Fan Zhang [Fri, 11 Mar 2016 17:08:08 +0000 (17:08 +0000)]
examples/ip_pipeline: add pcap file source

This patch add PCAP file support to ip_pipeline. Input port type SOURCE
now supports loading specific PCAP file and sends the packets in it to
pipeline instance. The packets are then released by SINK output port. This
feature can be applied by specifying parameters in configuration file as
shown below;

[PIPELINE1]
type = PASS-THROUGH
core = 1
pktq_in = SOURCE0 SOURCE1
pktq_out = SINK0 SINK1
pcap_file_rd = /path/to/eth1.PCAP /path/to/eth2.PCAP
pcap_bytes_rd_per_pkt = 0 64

The configuration section "pcap_file_rd" contains full path and name of
the PCAP file to be loaded. If multiple SOURCEs exists, each shall have
its own PCAP file path listed in this section, separated by spaces.
Multiple SOURCE ports may share same PCAP file to be copied.

The configuration section "pcap_bytes_rd_per_pkt" contains integer value
and indicates the maximum number of bytes to be copied from each packet
in the PCAP file. If this value is "0", all packets in the file will be
copied fully; if the packet size is smaller than the assigned value, the
entire packet is copied. Same as "pcap_file_rd", every SOURCE shall have
its own maximum copy byte number.

To enable PCAP support to IP pipeline, the compiler option
CONFIG_RTE_PORT_PCAP must be set to 'y'. It is possible to disable PCAP
support by removing "pcap_file_rd" and "pcap_bytes_rd_per_pkt" lines
from the configuration file.

Signed-off-by: Fan Zhang <roy.fan.zhang@intel.com>
Acked-by: Cristian Dumitrescu <cristian.dumitrescu@intel.com>
8 years agoport: add pcap file source
Fan Zhang [Fri, 11 Mar 2016 17:08:07 +0000 (17:08 +0000)]
port: add pcap file source

Originally, source ports in librte_port is an input port used as packet
generator. Similar to Linux kernel /dev/zero character device, it
generates null packets. This patch adds optional PCAP file support to
source port: instead of sending NULL packets, the source port generates
packets copied from a PCAP file. To increase the performance, the packets
in the file are loaded to memory initially, and copied to mbufs in circular
manner. Users can enable or disable this feature by setting
CONFIG_RTE_PORT_PCAP compiler option "y" or "n".

Signed-off-by: Fan Zhang <roy.fan.zhang@intel.com>
Acked-by: Cristian Dumitrescu <cristian.dumitrescu@intel.com>
8 years agoi40e: add tunnel filter for IP in GRE
Xutao Sun [Thu, 10 Mar 2016 03:06:01 +0000 (11:06 +0800)]
i40e: add tunnel filter for IP in GRE

Signed-off-by: Xutao Sun <xutao.sun@intel.com>
Signed-off-by: Jijiang Liu <jijiang.liu@intel.com>
8 years agoethdev: add IP in GRE tunnel
Xutao Sun [Thu, 10 Mar 2016 03:06:00 +0000 (11:06 +0800)]
ethdev: add IP in GRE tunnel

Signed-off-by: Xutao Sun <xutao.sun@intel.com>
Signed-off-by: Jijiang Liu <jijiang.liu@intel.com>
8 years agoethdev: rework tunnel filtering structure
Xutao Sun [Thu, 10 Mar 2016 03:05:59 +0000 (11:05 +0800)]
ethdev: rework tunnel filtering structure

Change the fields of outer_mac and inner_mac in struct
rte_eth_tunnel_filter_conf from pointer to struct in order to
keep the code's readability.

Signed-off-by: Xutao Sun <xutao.sun@intel.com>
Signed-off-by: Jijiang Liu <jijiang.liu@intel.com>
Signed-off-by: Thomas Monjalon <thomas.monjalon@6wind.com>