static void cmd_reconfig_device_queue(portid_t id, uint8_t dev, uint8_t queue);
-/* *** HELP *** */
-struct cmd_help_result {
+/* *** Help command with introduction. *** */
+struct cmd_help_brief_result {
cmdline_fixed_string_t help;
};
-static void cmd_help_parsed(__attribute__((unused)) void *parsed_result,
- struct cmdline *cl,
- __attribute__((unused)) void *data)
+static void cmd_help_brief_parsed(__attribute__((unused)) void *parsed_result,
+ struct cmdline *cl,
+ __attribute__((unused)) void *data)
{
- cmdline_printf(cl,
- "\n"
- "TEST PMD\n"
- "--------\n"
- "\n"
- "This commandline can be used to configure forwarding\n"
- "\n");
- cmdline_printf(cl,
- "Display informations:\n"
- "---------------------\n"
- "- show port info|stats|fdir|stat_qmap X|all\n"
- " Diplays information or stats or stats queue mapping on port X, or all\n"
- "- clear port stats X|all\n"
- " Clear stats for port X, or all\n"
- "- show config rxtx|cores|fwd\n"
- " Displays the given configuration\n"
- "- read reg port_id reg_off\n"
- " Displays value of a port register\n"
- "- read regfield port_id reg_off bit_x bit_y\n"
- " Displays value of a port register bit field\n"
- "- read regbit port_id reg_off bit_x\n"
- " Displays value of a port register bit\n"
- "- read rxd port_id queue_id rxd_id\n"
- " Displays a RX descriptor of a port RX queue\n"
- "- read txd port_id queue_id txd_id\n"
- " Displays a TX descriptor of a port TX queue\n"
- "\n");
- cmdline_printf(cl,
- "Configure:\n"
- "----------\n"
- "Modifications are taken into account once "
- "forwarding is restarted.\n"
- "- set default\n"
- " Set forwarding to default configuration\n"
- "- set nbport|nbcore|burst|verbose X\n"
- " Set number of ports, number of cores, number "
- "of packets per burst,\n or verbose level to X\n"
- "- set txpkts x[,y]*\n"
- " Set the length of each segment of TXONLY packets\n"
- "- set coremask|portmask X\n"
- " Set the hexadecimal mask of forwarding cores / "
- "forwarding ports\n"
- "- set corelist|portlist x[,y]*\n"
- " Set the list of forwarding cores / forwarding "
- "ports\n"
- "- vlan set strip|filter|qinq on/off port_id\n"
- " Set the VLAN strip, filter, QinQ(extended) on a port"
- "- rx_vlan add/rm vlan_id|all port_id\n"
- " Set the VLAN filter table, add/remove vlan_id, or all "
- "identifiers, to/from the set of VLAN Identifiers\n"
- "filtered by port_id\n"
- "- rx_vlan set tpid value port_id\n"
- " Set Outer VLAN TPID for Packet Filtering on a port \n"
- "- tx_vlan set vlan_id port_id\n"
- " Set hardware insertion of VLAN ID in packets sent on a port\n"
- "- tx_vlan reset port_id\n"
- " Disable hardware insertion of a VLAN header in "
- "packets sent on port_id\n"
- "- tx_checksum set mask port_id\n"
- " Enable hardware insertion of checksum offload with "
- "the 4-bit mask (0~0xf)\n in packets sent on port_id\n"
- " Please check the NIC datasheet for HW limits\n"
- " bit 0 - insert ip checksum offload if set \n"
- " bit 1 - insert udp checksum offload if set \n"
- " bit 2 - insert tcp checksum offload if set\n"
- " bit 3 - insert sctp checksum offload if set\n"
+ cmdline_printf(
+ cl,
+ "\n"
+ "Help is available for the following sections:\n\n"
+ " help control : Start and stop forwarding.\n"
+ " help display : Displaying port, stats and config "
+ "information.\n"
+ " help config : Configuration information.\n"
+ " help ports : Configuring ports.\n"
+ " help flowdir : Flow Director filter help.\n"
+ " help registers : Reading and setting port registers.\n"
+ " help all : All of the above sections.\n\n"
+ );
+
+}
+
+cmdline_parse_token_string_t cmd_help_brief_help =
+ TOKEN_STRING_INITIALIZER(struct cmd_help_brief_result, help, "help");
+
+cmdline_parse_inst_t cmd_help_brief = {
+ .f = cmd_help_brief_parsed,
+ .data = NULL,
+ .help_str = "show help",
+ .tokens = {
+ (void *)&cmd_help_brief_help,
+ NULL,
+ },
+};
+
+/* *** Help command with help sections. *** */
+struct cmd_help_long_result {
+ cmdline_fixed_string_t help;
+ cmdline_fixed_string_t section;
+};
+
+static void cmd_help_long_parsed(void *parsed_result,
+ struct cmdline *cl,
+ __attribute__((unused)) void *data)
+{
+ int show_all = 0;
+ struct cmd_help_long_result *res = parsed_result;
+
+ if (!strcmp(res->section, "all"))
+ show_all = 1;
+
+ if (show_all || !strcmp(res->section, "control")) {
+
+ cmdline_printf(
+ cl,
+ "\n"
+ "Control forwarding:\n"
+ "-------------------\n\n"
+
+ "start\n"
+ " Start packet forwarding with current configuration.\n\n"
+
+ "start tx_first\n"
+ " Start packet forwarding with current config"
+ " after sending one burst of packets.\n\n"
+
+ "stop\n"
+ " Stop packet forwarding, and display accumulated"
+ " statistics.\n\n"
+
+ "quit\n"
+ " Quit to prompt in Linux and reboot on Baremetal.\n\n"
+ );
+ }
+
+ if (show_all || !strcmp(res->section, "display")) {
+
+ cmdline_printf(
+ cl,
+ "\n"
+ "Display:\n"
+ "--------\n\n"
+
+ "show port (info|stats|fdir|stat_qmap) (port_id|all)\n"
+ " Display information for port_id, or all.\n\n"
+
+ "clear port (info|stats|fdir|stat_qmap) (port_id|all)\n"
+ " Clear information for port_id, or all.\n\n"
+
+ "show config (rxtx|cores|fwd)\n"
+ " Display the given configuration.\n\n"
+
+ "read rxd (port_id) (queue_id) (rxd_id)\n"
+ " Display an RX descriptor of a port RX queue.\n\n"
+
+ "read txd (port_id) (queue_id) (txd_id)\n"
+ " Display a TX descriptor of a port TX queue.\n\n"
+ );
+ }
+
+ if (show_all || !strcmp(res->section, "config")) {
+ cmdline_printf(
+ cl,
+ "\n"
+ "Configuration:\n"
+ "--------------\n"
+ "Configuration changes only become active when"
+ " forwarding is started/restarted.\n\n"
+
+ "set default\n"
+ " Reset forwarding to the default configuration.\n\n"
+
+ "set verbose (level)\n"
+ " Set the debug verbosity level X.\n\n"
+
+ "set nbport (num)\n"
+ " Set number of ports.\n\n"
+
+ "set nbcore (num)\n"
+ " Set number of cores.\n\n"
+
+ "set coremask (mask)\n"
+ " Set the forwarding cores hexadecimal mask.\n\n"
+
+ "set portmask (mask)\n"
+ " Set the forwarding ports hexadecimal mask.\n\n"
+
+ "set burst (num)\n"
+ " Set number of packets per burst.\n\n"
+
+ "set txpkts (x[,y]*)\n"
+ " Set the length of each segment of TXONLY"
+ " packets.\n\n"
+
+ "set corelist (x[,y]*)\n"
+ " Set the list of forwarding cores.\n\n"
+
+ "set portlist (x[,y]*)\n"
+ " Set the list of forwarding ports.\n\n"
+
+ "vlan set strip (on|off) (port_id)\n"
+ " Set the VLAN strip on a port.\n\n"
+
+ "vlan set filter (on|off) (port_id)\n"
+ " Set the VLAN filter on a port.\n\n"
+
+ "vlan set qinq (on|off) (port_id)\n"
+ " Set the VLAN QinQ (extended queue in queue)"
+ " on a port.\n\n"
+
+ "vlan set tpid (value) (port_id)\n"
+ " Set the outer VLAN TPID for Packet Filtering on"
+ " a port\n\n"
+
+ "rx_vlan add (vlan_id|all) (port_id)\n"
+ " Add a vlan_id, or all identifiers, to the set"
+ " of VLAN identifiers filtered by port_id.\n\n"
+
+ "rx_vlan rm (vlan_id|all) (port_id)\n"
+ " Remove a vlan_id, or all identifiers, from the set"
+ " of VLAN identifiers filtered by port_id.\n\n"
+
+ "tx_vlan set vlan_id (port_id)\n"
+ " Set hardware insertion of VLAN ID in packets sent"
+ " on a port.\n\n"
+
+ "tx_vlan reset (port_id)\n"
+ " Disable hardware insertion of a VLAN header in"
+ " packets sent on a port.\n\n"
+
+ "tx_checksum set mask (port_id)\n"
+ " Enable hardware insertion of checksum offload with"
+ " the 4-bit mask, 0~0xf, in packets sent on a port.\n"
+ " bit 0 - insert ip checksum offload if set\n"
+ " bit 1 - insert udp checksum offload if set\n"
+ " bit 2 - insert tcp checksum offload if set\n"
+ " bit 3 - insert sctp checksum offload if set\n"
+ " Please check the NIC datasheet for HW limits.\n\n"
+
#ifdef RTE_LIBRTE_IEEE1588
- "- set fwd io|mac|rxonly|txonly|csum|ieee1588\n"
- " Set IO, MAC, RXONLY, TXONLY, CSUM or IEEE1588 "
- "packet forwarding mode\n"
+ "set fwd (io|mac|rxonly|txonly|csum|ieee1588)\n"
+ " Set IO, MAC, RXONLY, CSUM or TXONLY or ieee1588"
+ " packet forwarding mode.\n\n"
+
#else
- "- set fwd io|mac|rxonly|txonly|csum\n"
- " Set IO, MAC, RXONLY, CSUM or TXONLY packet "
- "forwarding mode\n"
+ "set fwd (io|mac|rxonly|txonly|csum)\n"
+ " Set IO, MAC, RXONLY, CSUM or TXONLY packet"
+ " forwarding mode.\n\n"
+
#endif
- "- mac_addr add|remove X <xx:xx:xx:xx:xx:xx>\n"
- " Add/Remove the MAC address <xx:xx:xx:xx:xx:xx> on port X\n"
- "- set promisc|allmulti [all|X] on|off\n"
- " Set/unset promisc|allmulti mode on port X, or all\n"
- "- set flow_ctrl rx on|off tx on|off high_water low_water "
- "pause_time send_xon port_id \n"
- " Set the link flow control parameter on the port \n"
- "- set pfc_ctrl rx on|off tx on|off high_water low_water "
- "pause_time priority port_id \n"
- " Set the priority flow control parameter on the port \n"
- "- write reg port_id reg_off value\n"
- " Set value of a port register\n"
- "- write regfield port_id reg_off bit_x bit_y value\n"
- " Set bit field value of a port register\n"
- "- write regbit port_id reg_off bit_x value\n"
- " Set bit value of a port register\n"
- "- set stat_qmap tx|rx port_id queue_id qmapping\n"
- " Set statistics mapping (qmapping 0..15) for tx|rx queue_id on port_id\n"
- " e.g., 'set stat_qmap rx 0 2 5' sets rx queue 2 on port 0 to mapping 5\n"
- "\n");
- cmdline_printf(cl,
- "Control forwarding:\n"
- "-------------------\n"
- "- start\n"
- " Start packet forwarding with current config\n"
- "- start tx_first\n"
- " Start packet forwarding with current config"
- " after sending one burst\n of packets\n"
- "- stop\n"
- " Stop packet forwarding, and displays accumulated"
- " stats\n"
- "\n");
- cmdline_printf(cl,
- "Flow director mode:\n"
- "-------------------\n"
- "- add_signature_filter port_id ip|udp|tcp|sctp src\n"
- " ip_src_address port_src dst ip_dst_address port_dst\n"
- " flexbytes flexbytes_values vlan vlan_id queue queue_id\n"
- "- upd_signature_filter port_id ip|udp|tcp|sctp src \n"
- " ip_src_address port_src dst ip_dst_address port_dst\n"
- " flexbytes flexbytes_values vlan vlan_id queue queue_id\n"
- "- rm_signature_filter port_id ip|udp|tcp|sctp src\n"
- " ip_src_address port_src dst ip_dst_address port_dst\n"
- " flexbytes flexbytes_values vlan vlan_id\n"
- "- add_perfect_filter port_id ip|udp|tcp|sctp src\n"
- " ip_src_address port_src dst ip_dst_address port_dst\n"
- " flexbytes flexbytes_values vlan vlan_id queue \n"
- " queue_id soft soft_id\n"
- "- upd_perfect_filter port_id ip|udp|tcp|sctp src\n"
- " ip_src_address port_src dst ip_dst_address port_dst\n"
- " flexbytes flexbytes_values vlan vlan_id queue queue_id\n"
- "- rm_perfect_filter port_id ip|udp|tcp|sctp src\n"
- " ip_src_address port_src dst ip_dst_address port_dst\n"
- " flexbytes flexbytes_values vlan vlan_id soft soft_id\n"
- "- set_masks_filter port_id only_ip_flow 0|1 src_mask\n"
- " ip_src_mask port_src_mask dst_mask ip_dst_mask\n"
- " port_dst_mask flexbytes 0|1 vlan_id 0|1 vlan_prio 0|1\n"
- "- set_ipv6_masks_filter port_id only_ip_flow 0|1 src_mask\n"
- " ip_src_mask port_src_mask dst_mask ip_dst_mask\n"
- " port_dst_mask flexbytes 0|1 vlan_id 0|1\n"
- " vlan_prio 0|1 compare_dst 0|1\n"
- "\n");
- cmdline_printf(cl,
- "Port Operations:\n"
- "--------------\n"
- "- port start|stop|close all|X\n"
- " start/stop/close all ports or port X\n"
- "- port config all|X speed 10|100|1000|10000|auto "
- "duplex half|full|auto\n"
- " set speed for all ports or port X\n"
- "- port config all rxq|txq|rxd|txd value\n"
- " set number for rxq/txq/rxd/txd\n"
- "- port config all max-pkt-len value\n"
- " set the max packet lenght\n"
- "- port config all crc-strip|rx-cksum|hw-vlan|drop-en on|off\n"
- " set crc-strip/rx-checksum/hardware-vlan/drop_en on or off"
- "\n"
- "- port config all rss ip|udp|none\n"
- " set rss mode\n"
- "- port config port-id dcb vt on|off nb-tcs pfc on|off\n"
- " set dcb mode\n"
- "- port config all burst value\n"
- " set the number of packet per burst\n"
- "- port config all txpt|txht|txwt|rxpt|rxht|rxwt value\n"
- " set ring prefetch/host/writeback threshold for "
- "tx/rx queue\n"
- "- port config all txfreet|txrst|rxfreet value\n"
- " set free threshold for rx/tx, or set tx rs bit "
- "threshold\n"
- "\n");
- cmdline_printf(cl,
- "Misc:\n"
- "-----\n"
- "- quit\n"
- " Quit to prompt in linux, and reboot on baremetal\n"
- "\n");
+ "mac_addr add (port_id) (XX:XX:XX:XX:XX:XX)\n"
+ " Add a MAC address on port_id.\n\n"
+
+ "mac_addr remove (port_id) (XX:XX:XX:XX:XX:XX)\n"
+ " Remove a MAC address from port_id.\n\n"
+
+ "set promisc (port_id|all) (on|off)\n"
+ " Set the promiscuous mode on port_id, or all.\n\n"
+
+ "set allmulti (port_id|all) (on|off)\n"
+ " Set the allmulti mode on port_id, or all.\n\n"
+
+ "set flow_ctrl rx (on|off) tx (on|off) (high_water)"
+ " (low_water) (pause_time) (send_xon) (port_id)\n"
+ " Set the link flow control parameter on a port.\n\n"
+
+ "set pfc_ctrl rx (on|off) tx (on|off) (high_water)"
+ " (low_water) (pause_time) (priority) (port_id)\n"
+ " Set the priority flow control parameter on a"
+ " port.\n\n"
+
+ "set stat_qmap (tx|rx) (port_id) (queue_id) (qmapping)\n"
+ " Set statistics mapping (qmapping 0..15) for RX/TX"
+ " queue on port.\n"
+ " e.g., 'set stat_qmap rx 0 2 5' sets rx queue 2"
+ " on port 0 to mapping 5.\n\n"
+ );
+ }
+
+
+ if (show_all || !strcmp(res->section, "flowdir")) {
+
+ cmdline_printf(
+ cl,
+ "\n"
+ "Flow director mode:\n"
+ "-------------------\n\n"
+
+ "add_signature_filter (port_id) (ip|udp|tcp|sctp)"
+ " src (src_ip_address) (src_port)"
+ " dst (dst_ip_address) (dst_port)"
+ " flexbytes (flexbytes_values) vlan (vlan_id)"
+ " queue (queue_id)\n"
+ " Add a signature filter.\n\n"
+
+ "upd_signature_filter (port_id) (ip|udp|tcp|sctp)"
+ " src (src_ip_address) (src_port)"
+ " dst (dst_ip_address) (dst_port)"
+ " flexbytes (flexbytes_values) vlan (vlan_id)"
+ " queue (queue_id)\n"
+ " Update a signature filter.\n\n"
+
+ "rm_signature_filter (port_id) (ip|udp|tcp|sctp)"
+ " src (src_ip_address) (src_port)"
+ " dst (dst_ip_address) (dst_port)"
+ " flexbytes (flexbytes_values) vlan (vlan_id)\n"
+ " Remove a signature filter.\n\n"
+
+ "add_perfect_filter (port_id) (ip|udp|tcp|sctp)"
+ " src (src_ip_address) (src_port)"
+ " dst (dst_ip_address) (dst_port)"
+ " flexbytes (flexbytes_values) vlan (vlan_id)"
+ " queue (queue_id) soft (soft_id)\n"
+ " Add a perfect filter.\n\n"
+
+ "upd_perfect_filter (port_id) (ip|udp|tcp|sctp)"
+ " src (src_ip_address) (src_port)"
+ " dst (dst_ip_address) (dst_port)"
+ " flexbytes (flexbytes_values) vlan (vlan_id)"
+ " queue (queue_id)\n"
+ " Update a perfect filter.\n\n"
+
+ "rm_perfect_filter (port_id) (ip|udp|tcp|sctp)"
+ " src (src_ip_address) (src_port)"
+ " dst (dst_ip_address) (dst_port)"
+ " flexbytes (flexbytes_values) vlan (vlan_id)"
+ " soft (soft_id)\n"
+ " Remove a perfect filter.\n\n"
+
+ "set_masks_filter (port_id) only_ip_flow (0|1)"
+ " src_mask (ip_src_mask) (src_port_mask)"
+ " dst_mask (ip_dst_mask) (dst_port_mask)"
+ " flexbytes (0|1) vlan_id (0|1) vlan_prio (0|1)\n"
+ " Set IPv4 filter masks.\n\n"
+
+ "set_ipv6_masks_filter (port_id) only_ip_flow (0|1)"
+ " src_mask (ip_src_mask) (src_port_mask)"
+ " dst_mask (ip_dst_mask) (dst_port_mask)"
+ " flexbytes (0|1) vlan_id (0|1) vlan_prio (0|1)"
+ " compare_dst (0|1)\n"
+ " Set IPv6 filter masks.\n\n"
+ );
+ }
+
+ if (show_all || !strcmp(res->section, "ports")) {
+
+ cmdline_printf(
+ cl,
+ "\n"
+ "Port Operations:\n"
+ "----------------\n\n"
+
+ "port start (port_id|all)\n"
+ " Start all ports or port_id.\n\n"
+
+ "port stop (port_id|all)\n"
+ " Stop all ports or port_id.\n\n"
+
+ "port close (port_id|all)\n"
+ " Close all ports or port_id.\n\n"
+
+ "port config (port_id|all) speed (10|100|1000|10000|auto)"
+ " duplex (half|full|auto)\n"
+ " Set speed and duplex for all ports or port_id\n\n"
+
+ "port config all (rxq|txq|rxd|txd) (value)\n"
+ " Set number for rxq/txq/rxd/txd.\n\n"
+
+ "port config all max-pkt-len (value)\n"
+ " Set the max packet length.\n\n"
+
+ "port config all (crc-strip|rx-cksum|hw-vlan|drop-en)"
+ " (on|off)\n"
+ " Set crc-strip/rx-checksum/hardware-vlan/drop_en"
+ " for ports.\n\n"
+
+ "port config all rss (ip|udp|none)\n"
+ " Set the RSS mode.\n\n"
+
+ "port config (port_id) dcb vt (on|off) (traffic_class)"
+ " pfc (on|off)\n"
+ " Set the DCB mode.\n\n"
+
+ "port config all burst (value)\n"
+ " Set the number of packets per burst.\n\n"
+
+ "port config all (txpt|txht|txwt|rxpt|rxht|rxwt)"
+ " (value)\n"
+ " Set the ring prefetch/host/writeback threshold"
+ " for tx/rx queue.\n\n"
+
+ "port config all (txfreet|txrst|rxfreet) (value)\n"
+ " Set free threshold for rx/tx, or set"
+ " tx rs bit threshold.\n\n"
+ );
+ }
+
+ if (show_all || !strcmp(res->section, "registers")) {
+
+ cmdline_printf(
+ cl,
+ "\n"
+ "Registers:\n"
+ "----------\n\n"
+
+ "read reg (port_id) (address)\n"
+ " Display value of a port register.\n\n"
+
+ "read regfield (port_id) (address) (bit_x) (bit_y)\n"
+ " Display a port register bit field.\n\n"
+
+ "read regbit (port_id) (address) (bit_x)\n"
+ " Display a single port register bit.\n\n"
+
+ "write reg (port_id) (address) (value)\n"
+ " Set value of a port register.\n\n"
+
+ "write regfield (port_id) (address) (bit_x) (bit_y)"
+ " (value)\n"
+ " Set bit field of a port register.\n\n"
+
+ "write regbit (port_id) (address) (bit_x) (value)\n"
+ " Set single bit value of a port register.\n\n"
+ );
+ }
}
-cmdline_parse_token_string_t cmd_help_help =
- TOKEN_STRING_INITIALIZER(struct cmd_help_result, help, "help");
+cmdline_parse_token_string_t cmd_help_long_help =
+ TOKEN_STRING_INITIALIZER(struct cmd_help_long_result, help, "help");
-cmdline_parse_inst_t cmd_help = {
- .f = cmd_help_parsed,
+cmdline_parse_token_string_t cmd_help_long_section =
+ TOKEN_STRING_INITIALIZER(struct cmd_help_long_result, section,
+ "all#control#display#config#flowdir#"
+ "ports#registers");
+
+cmdline_parse_inst_t cmd_help_long = {
+ .f = cmd_help_long_parsed,
.data = NULL,
.help_str = "show help",
.tokens = {
- (void *)&cmd_help_help,
+ (void *)&cmd_help_long_help,
+ (void *)&cmd_help_long_section,
NULL,
},
};
+
/* *** start/stop/close all ports *** */
struct cmd_operate_port_result {
cmdline_fixed_string_t keyword;
struct cmd_config_dcb {
cmdline_fixed_string_t port;
cmdline_fixed_string_t config;
- uint8_t port_id;
+ uint8_t port_id;
cmdline_fixed_string_t dcb;
cmdline_fixed_string_t vt;
cmdline_fixed_string_t vt_en;
- uint8_t num_tcs;
+ uint8_t num_tcs;
cmdline_fixed_string_t pfc;
cmdline_fixed_string_t pfc_en;
};
struct dcb_config dcb_conf;
portid_t port_id = res->port_id;
struct rte_port *port;
-
+
port = &ports[port_id];
/** Check if the port is not started **/
if (port->port_status != RTE_PORT_STOPPED) {
printf("Please stop port %d first\n",port_id);
return;
}
-
+
dcb_conf.num_tcs = (enum rte_eth_nb_tcs) res->num_tcs;
if ((dcb_conf.num_tcs != ETH_4_TCS) && (dcb_conf.num_tcs != ETH_8_TCS)){
printf("The invalid number of traffic class,only 4 or 8 allowed\n");
}
/* DCB in VT mode */
- if (!strncmp(res->vt_en, "on",2))
- dcb_conf.dcb_mode = DCB_VT_ENABLED;
+ if (!strncmp(res->vt_en, "on",2))
+ dcb_conf.dcb_mode = DCB_VT_ENABLED;
else
dcb_conf.dcb_mode = DCB_ENABLED;
cmd_reconfig_device_queue(port_id, 1, 1);
}
-
+
cmdline_parse_token_string_t cmd_config_dcb_port =
TOKEN_STRING_INITIALIZER(struct cmd_config_dcb, port, "port");
cmdline_parse_token_string_t cmd_config_dcb_config =
__attribute__((unused)) void *data)
{
int on;
- struct cmd_vlan_offload_result *res = parsed_result;
+ struct cmd_vlan_offload_result *res = parsed_result;
char *str;
int i, len = 0;
portid_t port_id = 0;
unsigned int tmp;
-
+
str = res->port_id;
len = strnlen(str, STR_TOKEN_SIZE);
i = 0;
while(i < len){
if(str[i] == ',')
break;
-
+
i++;
}
str[i]='\0';
/* If queue_id greater that what 16-bits can represent, return */
if(tmp > 0xffff)
return;
-
+
queue_id = (uint16_t)tmp;
rx_vlan_strip_set_on_queue(port_id, queue_id, on);
}
/* list of instructions */
cmdline_parse_ctx_t main_ctx[] = {
- (cmdline_parse_inst_t *)&cmd_help,
+ (cmdline_parse_inst_t *)&cmd_help_brief,
+ (cmdline_parse_inst_t *)&cmd_help_long,
(cmdline_parse_inst_t *)&cmd_quit,
(cmdline_parse_inst_t *)&cmd_showport,
(cmdline_parse_inst_t *)&cmd_showportall,
printf("usage: %s [--interactive|-i] [--help|-h] | ["
"--coremask=COREMASK --portmask=PORTMASK --numa "
"--mbuf-size= | --total-num-mbufs= | "
+ "--nb-cores= | --nb-ports= | "
"--eth-peers-configfile= | "
- "--eth-peer=X,M:M:M:M:M:M | --nb-cores= | --nb-ports= | "
+ "--eth-peer=X,M:M:M:M:M:M | "
"--pkt-filter-mode= |"
"--rss-ip | --rss-udp | "
"--rxpt= | --rxht= | --rxwt= | --rxfreet= | "
"--txpt= | --txht= | --txwt= | --txfreet= | "
"--txrst= | --txqflags= ]\n",
progname);
- printf(" --interactive: run in interactive mode\n");
- printf(" --help: display this message and quit\n");
- printf(" --eth-peers-configfile=name of file with ethernet addresses "
- "of peer ports\n");
- printf(" --eth-peer=X,M:M:M:M:M:M set the mac address of the X peer "
- "port (0 <= X < %d)\n", RTE_MAX_ETHPORTS);
- printf(" --nb-cores=N set the number of forwarding cores"
- " (1 <= N <= %d)\n", nb_lcores);
- printf(" --nb-ports=N set the number of forwarding ports"
- " (1 <= N <= %d)\n", nb_ports);
+ printf(" --interactive: run in interactive mode.\n");
+ printf(" --help: display this message and quit.\n");
+ printf(" --nb-cores=N: set the number of forwarding cores "
+ "(1 <= N <= %d).\n", nb_lcores);
+ printf(" --nb-ports=N: set the number of forwarding ports "
+ "(1 <= N <= %d).\n", nb_ports);
printf(" --coremask=COREMASK: hexadecimal bitmask of cores running "
"the packet forwarding test. The master lcore is reserved for "
- "command line parsing only, and can not be masked on for running"
- "the packet forwarding\n");
+ "command line parsing only, and cannot be masked on for "
+ "packet forwarding.\n");
printf(" --portmask=PORTMASK: hexadecimal bitmask of ports used "
- "by the packet forwarding test\n");
+ "by the packet forwarding test.\n");
printf(" --numa: enable NUMA-aware allocation of RX/TX rings and of "
- " RX memory buffers (mbufs)\n");
- printf(" --mbuf-size=N set the data size of mbuf to N bytes\n");
- printf(" --total-num-mbufs=N set the number of mbufs to be allocated "
- "in mbuf pools\n");
- printf(" --max-pkt-len=N set the maximum size of packet to N bytes\n");
- printf(" --pkt-filter-mode=N: set Flow director mode "
- "( N: none (default mode) or signature or perfect)\n");
- printf(" --pkt-filter-report-hash=N: set Flow director report mode "
- "( N: none or match (default) or always)\n");
- printf(" --pkt-filter-size=N: set Flow director mode "
- "( N: 64K (default mode) or 128K or 256K)\n");
- printf(" --pkt-filter-flexbytes-offset=N: set flexbytes-offset."
- " The offset is defined in word units counted from the"
- " first byte of the destination Ethernet MAC address."
- " 0 <= N <= 32\n");
- printf(" --pkt-filter-drop-queue=N: set drop-queue."
- " In perfect mode, when you add a rule with queue -1"
- " the packet will be enqueued into the rx drop-queue."
- " If the drop-queue doesn't exist, the packet is dropped."
- " By default drop-queue=127\n");
- printf(" --crc-strip: enable CRC stripping by hardware\n");
- printf(" --enable-rx-cksum: enable rx hardware checksum offload\n");
- printf(" --disable-hw-vlan: disable hardware vlan\n");
- printf(" --enable-drop-en: enable per queue packet drop\n");
- printf(" --disable-rss: disable rss\n");
+ "RX memory buffers (mbufs).\n");
+ printf(" --mbuf-size=N: set the data size of mbuf to N bytes.\n");
+ printf(" --total-num-mbufs=N: set the number of mbufs to be allocated "
+ "in mbuf pools.\n");
+ printf(" --max-pkt-len=N: set the maximum size of packet to N bytes.\n");
+ printf(" --eth-peers-configfile=name: config file with ethernet addresses "
+ "of peer ports.\n");
+ printf(" --eth-peer=X,M:M:M:M:M:M: set the MAC address of the X peer "
+ "port (0 <= X < %d).\n", RTE_MAX_ETHPORTS);
+ printf(" --pkt-filter-mode=N: set Flow Director mode "
+ "(N: none (default mode) or signature or perfect).\n");
+ printf(" --pkt-filter-report-hash=N: set Flow Director report mode "
+ "(N: none or match (default) or always).\n");
+ printf(" --pkt-filter-size=N: set Flow Director mode "
+ "(N: 64K (default mode) or 128K or 256K).\n");
+ printf(" --pkt-filter-flexbytes-offset=N: set flexbytes-offset. "
+ "The offset is defined in word units counted from the "
+ "first byte of the destination Ethernet MAC address. "
+ "0 <= N <= 32.\n");
+ printf(" --pkt-filter-drop-queue=N: set drop-queue. "
+ "In perfect mode, when you add a rule with queue = -1 "
+ "the packet will be enqueued into the rx drop-queue. "
+ "If the drop-queue doesn't exist, the packet is dropped. "
+ "By default drop-queue=127.\n");
+ printf(" --crc-strip: enable CRC stripping by hardware.\n");
+ printf(" --enable-rx-cksum: enable rx hardware checksum offload.\n");
+ printf(" --disable-hw-vlan: disable hardware vlan.\n");
+ printf(" --enable-drop-en: enable per queue packet drop.\n");
+ printf(" --disable-rss: disable rss.\n");
printf(" --port-topology=N: set port topology (N: paired (default) or "
- "chained)\n");
- printf(" --rss-ip: set RSS functions to IPv4/IPv6 only \n");
- printf(" --rss-udp: set RSS functions to IPv4/IPv6 + UDP\n");
- printf(" --rxq=N set the number of RX queues per port to N\n");
- printf(" --rxd=N set the number of descriptors in RX rings to N\n");
- printf(" --txq=N set the number of TX queues per port to N\n");
- printf(" --txd=N set the number of descriptors in TX rings to N\n");
- printf(" --burst=N set the number of packets per burst to N\n");
- printf(" --mbcache=N set the cache of mbuf memory pool to N\n");
- printf(" --rxpt=N set prefetch threshold register of RX rings to N"
- " (0 <= N <= 16)\n");
- printf(" --rxht=N set the host threshold register of RX rings to N"
- " (0 <= N <= 16)\n");
- printf(" --rxfreet=N set the free threshold of RX descriptors to N"
- " (0 <= N < value of rxd)\n");
- printf(" --rxwt=N set the write-back threshold register of RX rings"
- " to N (0 <= N <= 16)\n");
- printf(" --txpt=N set the prefetch threshold register of TX rings"
- " to N (0 <= N <= 16)\n");
- printf(" --txht=N set the nhost threshold register of TX rings to N"
- " (0 <= N <= 16)\n");
- printf(" --txwt=N set the write-back threshold register of TX rings"
- " to N (0 <= N <= 16)\n");
- printf(" --txfreet=N set the transmit free threshold of TX rings to N"
- " (0 <= N <= value of txd)\n");
- printf(" --txrst=N set the transmit RS bit threshold of TX rings to N"
- " (0 <= N <= value of txd)\n");
- printf(" --txqflags=0xXXXXXXXX hexidecimal bitmask of TX queue flags"
- " (0 <= N <= 0x7FFFFFFF)\n");
- printf(" --tx-queue-stats-mapping (port,queue,mapping)[,(port,queue,mapping]:"
- " tx queues statistics counters mapping"
- " (0 <= mapping <= %d)\n", RTE_ETHDEV_QUEUE_STAT_CNTRS - 1);
- printf(" --rx-queue-stats-mapping (port,queue,mapping)[,(port,queue,mapping]:"
- " rx queues statistics counters mapping"
- " (0 <= mapping <= %d)\n", RTE_ETHDEV_QUEUE_STAT_CNTRS - 1);
+ "chained).\n");
+ printf(" --rss-ip: set RSS functions to IPv4/IPv6 only .\n");
+ printf(" --rss-udp: set RSS functions to IPv4/IPv6 + UDP.\n");
+ printf(" --rxq=N: set the number of RX queues per port to N.\n");
+ printf(" --rxd=N: set the number of descriptors in RX rings to N.\n");
+ printf(" --txq=N: set the number of TX queues per port to N.\n");
+ printf(" --txd=N: set the number of descriptors in TX rings to N.\n");
+ printf(" --burst=N: set the number of packets per burst to N.\n");
+ printf(" --mbcache=N: set the cache of mbuf memory pool to N.\n");
+ printf(" --rxpt=N: set prefetch threshold register of RX rings to N "
+ "(0 <= N <= 16).\n");
+ printf(" --rxht=N: set the host threshold register of RX rings to N "
+ "(0 <= N <= 16).\n");
+ printf(" --rxfreet=N: set the free threshold of RX descriptors to N "
+ "(0 <= N < value of rxd).\n");
+ printf(" --rxwt=N: set the write-back threshold register of RX rings "
+ "to N (0 <= N <= 16).\n");
+ printf(" --txpt=N: set the prefetch threshold register of TX rings "
+ "to N (0 <= N <= 16).\n");
+ printf(" --txht=N: set the nhost threshold register of TX rings to N "
+ "(0 <= N <= 16).\n");
+ printf(" --txwt=N: set the write-back threshold register of TX rings "
+ "to N (0 <= N <= 16).\n");
+ printf(" --txfreet=N: set the transmit free threshold of TX rings to N "
+ "(0 <= N <= value of txd).\n");
+ printf(" --txrst=N: set the transmit RS bit threshold of TX rings to N "
+ "(0 <= N <= value of txd).\n");
+ printf(" --txqflags=0xXXXXXXXX: hexadecimal bitmask of TX queue flags "
+ "(0 <= N <= 0x7FFFFFFF).\n");
+ printf(" --tx-queue-stats-mapping=(port,queue,mapping)[,(port,queue,mapping]: "
+ "tx queues statistics counters mapping "
+ "(0 <= mapping <= %d).\n", RTE_ETHDEV_QUEUE_STAT_CNTRS - 1);
+ printf(" --rx-queue-stats-mapping=(port,queue,mapping)[,(port,queue,mapping]: "
+ "rx queues statistics counters mapping "
+ "(0 <= mapping <= %d).\n", RTE_ETHDEV_QUEUE_STAT_CNTRS - 1);
}
static int
config_file = fopen(config_filename, "r");
if (config_file == NULL) {
- perror("open log file failed\n");
+ perror("Failed to open eth config file\n");
return -1;
}
break;
if (cmdline_parse_etheraddr(NULL, buf, &peer_eth_addrs[i]) < 0 ){
- printf("bad format of mac address on line %d\n", i);
+ printf("Bad MAC address format on line %d\n", i+1);
fclose(config_file);
return -1;
}
{ "portmask", 1, 0, 0 },
{ "numa", 0, 0, 0 },
{ "mbuf-size", 1, 0, 0 },
- { "total-num-mbufs", 1, 0, 0 },
+ { "total-num-mbufs", 1, 0, 0 },
{ "max-pkt-len", 1, 0, 0 },
{ "pkt-filter-mode", 1, 0, 0 },
{ "pkt-filter-report-hash", 1, 0, 0 },
git.droids-corp.org / dpdk.git / commitdiff