support lolo's board

[protos/xbee-avr.git] / uart_config.h

diff --git a/uart_config.h b/uart_config.h
index 8795a7e..f8b2f09 100644 (file)
--- a/uart_config.h
+++ b/uart_config.h
@@ -27,33 +27,64 @@
 #define UART_CONFIG_H\r
 \r
 /*\r
- * UART1 definitions\r
+ * UART0 definitions\r
  */\r
 \r
-/* compile uart1 fonctions, undefine it to pass compilation */\r
-#define UART1_COMPILE\r
+/* compile uart0 fonctions, undefine it to pass compilation */\r
+#define UART0_COMPILE\r
 \r
-/* enable uart1 if == 1, disable if == 0 */\r
-#define UART1_ENABLED  1\r
+/* enable uart0 if == 1, disable if == 0 */\r
+#define UART0_ENABLED  1\r
 \r
-/* enable uart1 interrupts if == 1, disable if == 0 */\r
-#define UART1_INTERRUPT_ENABLED  1\r
+/* enable uart0 interrupts if == 1, disable if == 0 */\r
+#define UART0_INTERRUPT_ENABLED  1\r
 \r
-#define UART1_BAUDRATE 57600\r
+#define UART0_BAUDRATE 57600\r
 \r
 /*\r
  * if you enable this, the maximum baudrate you can reach is\r
  * higher, but the precision is lower.\r
  */\r
-#define UART1_USE_DOUBLE_SPEED 1\r
+#define UART0_USE_DOUBLE_SPEED 1\r
 \r
-#define UART1_RX_FIFO_SIZE 64\r
-#define UART1_TX_FIFO_SIZE 127\r
-#define UART1_NBITS 8\r
+#define UART0_RX_FIFO_SIZE 64\r
+#define UART0_TX_FIFO_SIZE 127\r
+#define UART0_NBITS 8\r
 \r
-#define UART1_PARITY UART_PARTITY_NONE\r
+#define UART0_PARITY UART_PARTITY_NONE\r
 \r
-#define UART1_STOP_BIT UART_STOP_BITS_1\r
+#define UART0_STOP_BIT UART_STOP_BITS_1\r
+\r
+/* .... same for uart 1, 2, 3 ... */\r
+\r
+/*\r
+ * UART2 definitions\r
+ */\r
+\r
+/* compile uart2 fonctions, undefine it to pass compilation */\r
+#define UART2_COMPILE\r
+\r
+/* enable uart2 if == 1, disable if == 0 */\r
+#define UART2_ENABLED  1\r
+\r
+/* enable uart2 interrupts if == 1, disable if == 0 */\r
+#define UART2_INTERRUPT_ENABLED  1\r
+\r
+#define UART2_BAUDRATE 9600\r
+\r
+/*\r
+ * if you enable this, the maximum baudrate you can reach is\r
+ * higher, but the precision is lower.\r
+ */\r
+#define UART2_USE_DOUBLE_SPEED 1\r
+\r
+#define UART2_RX_FIFO_SIZE 64\r
+#define UART2_TX_FIFO_SIZE 127\r
+#define UART2_NBITS 8\r
+\r
+#define UART2_PARITY UART_PARTITY_NONE\r
+\r
+#define UART2_STOP_BIT UART_STOP_BITS_1\r
 \r
 /* .... same for uart 1, 2, 3 ... */\r
 \r